W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 2 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-2 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.55 Hz Electrical “Q” (Qes) 0.554 Mechanical “Q” (Qms) 8.731 Total Speaker “Q” (Qts) 0.521 Equivalent Compliance (Vas) 2.544 cu ft / 72.04 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.23% Efficiency (1 W / 1 m)** 85.9 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 2.210 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 38.99 Hz Fc 48.39 Hz Qtc 0.9496 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 4 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.21 Hz Electrical “Q” (Qes) 0.535 Mechanical “Q” (Qms) 8.2 Total Speaker “Q” (Qts) 0.502 Equivalent Compliance (Vas) 2.706 cu ft / 76.63 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.25% Efficiency (1 W / 1 m)** 86.1 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 3.915 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 39.63 Hz Fc 48.75 Hz Qtc 0.9338 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31.41 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 10-inch Subwoofer (300 W, 4 Ω)   The 10W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (4.6 in. / 117 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 10-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 10W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.92 in / 125 mm Mounting Depth (E) 4.6 in / 117 mm Driver Displacement 0.037 cu ft / 1.05 L Net Weight 9.9 lb / 4.5 kg Parameters Free Air Resonance (Fs) 26.15 Hz Electrical “Q” (Qes) 0.475 Mechanical “Q” (Qms) 7.243 Total Speaker “Q” (Qts) 0.446 Equivalent Compliance (Vas) 1.533 cu ft / 43.41 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.16% Efficiency (1 W / 1 m)** 84.2 dB SPL Effective Piston Area (Sd) 53.584 sq in / 0.0346 sq m DC Resistance (Re) 3.902 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 16.5 in / 419 mm External Height (H) 13.5 in / 343 mm External Depth (D) 7 in / 178 mm F3 43.1 Hz Fc 50.9 Hz Qtc 0.868 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.9 cu ft / 25.5 L External Width (W) 17.0 in / 432 mm External Height (H) 11.5 in / 292 mm External Depth (D) 15.25 in / 387 mm Internal Slot Port Width (SW) 1.125 in / 28.6 mm Internal Slot Port Height (SH) 10.0 in / 254 mm Internal Slot Port Length (SL) 30.1875 in / 767 mm Port Extension Length (EL) 12.50 in / 318 mm Tuning Frequency (Fb) 32.17 Hz F3 31.92 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 8-inch Subwoofer (150 W, 4 Ω) The 8W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (3.86 in. / 98 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 8-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 8W1v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a compact 0.350 cu. ft. (9.90 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 8.0 in / 200 mm Overall Diameter (A) 8.5 in / 216 mm Mounting Hole Diameter (B) 7.09 in / 180 mm Bolt Hole Circle Diameter (C) 7.85 in / 199 mm Motor Outer Diameter (D) 4.72 in / 120 mm Mounting Depth (E) 3.86 in / 98 mm Driver Displacement 0.018 cu ft / 0.51 L Net Weight 7.4 lb / 3.4 kg Parameters Free Air Resonance (Fs) 35.40 Hz Electrical “Q” (Qes) 0.451 Mechanical “Q” (Qms) 5.791 Total Speaker “Q” (Qts) 0.418 Equivalent Compliance (Vas) 0.68 cu ft / 19.26 L One-Way Linear Excursion (Xmax)* 0.3 in / 8 mm Reference Efficiency (no) 0.18% Efficiency (1 W / 1 m)** 84.8 dB SPL Effective Piston Area (Sd) 32.67 sq in / 0.0211 sq m DC Resistance (Re) 4.06 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.350 cu ft / 9.90 L External Width (W) 12 in / 305 mm External Height (H) 10 in / 254 mm External Depth (D) 8.625 in / 219 mm F3 59.9 Hz Fc 60.7 Hz Qtc 0.717 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.50 cu ft / 14.2 L External Width (W) 13.0 in / 330 mm External Height (H) 10 in / 254 mm External Depth (D) 11.125 in / 283 mm Internal Port Diameter (ID) 2 in / 51 mm Port Length (L) 10 in / 254 mm Tuning Frequency (Fb) 38 Hz F3 39.10 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

Custom-fit (CF) Speaker System: 3.5" (90 mm) Mid-Tweeter Engineered to deliver amazing sound from factory locations, CF speakers are designed with shallow polymer frames and breakaway mounting tabs for maximum compatibility in today's most popular vehicles, including those from Chevrolet, GMC, Cadillac, Dodge, Jeep, RAM, Toyota and many more.  CF drivers benefit from our proprietary FEA modeling and expertise in loudspeaker design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic low-distortion sound. At the core of the CF-350mt mid-tweeter is a proprietary 3.5" (90 mm) composite frame and a DMA-optimized motor system. An ultralight, fiber-reinforced pulp cone with a custom "S" roll surround delivers excellent efficiency and extended high-frequency response. A flat, progressive-roll spider ensures linear compliance, while the neodymium motor packs astonishing energy from an ultracompact and lightweight package. Each speaker's glass-filled, high-temperature polymer frame is outfitted with insert-molded terminals and a low-profile perforated metal grille to easily fit behind factory trim, while providing excellent UV protection in exposed dashboard locations. For passive applications as midtreble speakers, in-line second order high-pass filters are included to enhance smoothness and improve power handling. CF-350mt speakers can also be used actively as true midrange or mid-tweeter drivers to create outstanding two-way or three-way systems. For active applications, we recommend a high-quality digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, and the recommended bandwidths below. Design Bandwidth:With 24 dB/octave filters: 400 Hz-20 kHzWith 12 dB/octave filters: 500 Hz-20 kHz  Enjoy factory-fit and next-level sound from OEM locations with CF speakers! Speakers are sold as a pair and include built-in grilles. General Specifications Continuous Power Handling (RMS) 35 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 86.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 450 Hz - 20 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 3.46 in / 88 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 1.29 in / 33 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion (E) 0.26 / 7 mm Mounting Hole Diameter (F) 3.12 in / 80 mm Mounting Depth (G) 1.59 in / 40 mm *Does not take into account mounting tabs

Custom-fit (CF) Speaker System: 2.75" (70 mm) Mid-Tweeter Engineered to deliver amazing sound from factory locations, CF speakers are designed with shallow polymer frames and breakaway mounting tabs for maximum compatibility in today's most popular vehicles, including those from Chevrolet, GMC, Cadillac, Dodge, Jeep, RAM, Toyota and many more.  CF drivers benefit from our proprietary FEA modeling and expertise in loudspeaker design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic low-distortion sound. At the core of the CF-275mt mid-tweeter is a proprietary, 2.75" (70 mm) composite frame and a DMA-optimized motor system. An ultralight, fiber-reinforced pulp cone with a custom "S" roll surround delivers excellent efficiency and extended high-frequency response. A flat, progressive-roll spider ensures linear compliance, while the neodymium motor packs astonishing energy from an ultracompact and lightweight package. Each speaker's glass-filled, high-temperature polymer frame is outfitted with insert-molded terminals and a low-profile perforated metal grille to easily fit behind factory trim while providing excellent UV protection in exposed dashboard locations. For passive applications as midtreble speakers, in-line, second order high-pass filters are included to enhance smoothness and improve power handling. CF-275mt speakers can also be used actively, as true midrange or mid-tweeter drivers to create outstanding two-way or three-way systems. For active applications, we recommend a high-quality digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, and the recommended bandwidths below. Design Bandwidth:With 24 dB/octave filters: 400 Hz-20 kHzWith 12 dB/octave filters: 500 Hz-20 kHz Enjoy factory-fit and next-level sound from OEM locations with CF speakers! Speakers are sold as a pair and include built-in grilles. General Specifications Continuous Power Handling (RMS) 30 W Recommended Amplifier Power (RMS) 10 - 40 W / Ch. System Efficiency 82.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 450 Hz - 20 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 2.85 in / 72 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 1.29 in / 33 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion (E) 0.26 / 6.5 mm Mounting Hole Diameter (F) 2.48 in / 63 mm Mounting Depth (G) 1.39 in / 35 mm *Does not take into account mounting tabs

Two-way Component System: 6.5" (165 mm) Woofer, 1" (25 mm) Silk Dome Tweeter   Born from shared technologies used in our flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grilles C6 Tweeter Features:• Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General SpecificationsContinuous Power Handling (RMS)    100 WRecommended Amplifier Power (RMS)    25 - 150 W / Ch.System Efficiency    87.37 dB @ 1 W / 1 mSystem Nominal Impedance    4 ΩSystem Frequency Response    53 Hz – 21 KHz ± 3 dB   Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.11 in / 54 mm Flush Mount Mounting Hole Diameter (B) 1.85 in / 47 mm Flush Mount Mounting Depth (C) 1.85 in / 47 mm Flush Mount Protrusion (D1) 0.30 in / 8 mm Surface Mount Protrusion (D2) 1.04 in / 26 mm Crossover Physical Specifications Width (W) 3.36 in / 85 mm Height (H) 1.44 in / 37 mm Depth (D) 4.72 in / 120 mm

6.5" (165 mm) Component Woofer (with Grille) Born from shared technologies used in our flagship C7 speakers, the C6-650cw component woofer benefits from vast woofer design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-650cw component woofer features a proprietary cast alloy frame outfitted with our Elevated Frame Cooling™ technology and a DMA-optimized motor system to generate outstanding midbass impact with ultralow distortion. Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor, such as the JL Audio TwK® DSP, or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-650cw Component Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grille Design Bandwidth:With 48 dB/octave filters: 55 Hz-6 kHzWith 24 dB/octave filters: 65 Hz-6 kHzWith 12 dB/octave filters: 80 Hz-6 kHz Component woofers are sold individually and include a plastic grille tray, one fine steel mesh grille and one electroformed JL Audio badge logo. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 55 Hz - 6 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface

2-Way Component System: 6.5-inch (165 mm) Woofer, 1-inch (25 mm) Silk Dome Tweeter The C1-650se component system is engineered to deliver remarkable fidelity and outstanding value in a format that easily fits in factory locations. Outfitted with pure, silk dome tweeters, the C1-650se component system stands above others in its category with silky smooth, high-frequency clarity and definition. The 1-inch tweeter’s edge-driven design delivers excellent off-axis response and treble extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. Outboard, 3rd order, high-pass in-line filters, with Advanced Tweeter Protection Circuitry, are also included to guard against high-distortion damage and improve power handling. For maximum installation versatility, surface and flush tweeter mounts are also included.  C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low-distortion sound. At the core of the C1-650 woofer is a proprietary, stamped, steel 6.5-inch (165 mm) frame and DMA-optimized motor system. A mineral-filled, injection-molded, polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to each spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. To maximize fit, multi-application adaptor rings are included for the woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well.  When it comes to value, C1-650se is a real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 21 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.25 in / 159 mm Grille Tray Outer Diameter (B) 6.84 in / 174 mm Motor Outer Diameter (C) 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion** (E) N/A Mounting Hole Diameter (F) 5.02 in / 128 mm Mounting Depth (G) 2.07 in / 53 mm *Does not take into account mounting tabs**Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 1.97 in / 50 mm Surface Mount Fixture Diameter (A2) 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B) 1.75 in / 45 mm Flush Mount Mounting Depth (C) 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 0.87 in / 22 mm

Coaxial Speaker System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 91.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion** (D) 0.41 in / 10 mm Frontal Grille Protrusion (E) N/A Mounting Hole Diameter (F) N/A Mounting Depth (G) 2.75 in / 70 mm *Does not take into account mounting tabs**Frontal coaxial tweeter protrusion measured from mounting surface

SPECIFICATIONSContinuous Power Handling (RMS): 600 WRecommended Amplifier Power (RMS): 250 - 600 WNominal Impedance (Znom): 2 ΩNominal Diameter: 13.5 in / 345 mmOverall Diameter (A) A1: 14.2 in / 361mmA2: 13.0 in / 330 mmMounting Hole Diameter (B): 12.5 in / 318 mmBolt Hole Circle Diameter (C): 13.5 in / 343 mmMotor Outer Diameter (D): 6.75 in / 171 mmMounting Depth (E): 2.625 in / 67 mmDriver Displacement: 0.052 cu ft / 1.47 LNet Weight: 20.5 lb / 9.3 kgPARAMETERSFree Air Resonance (Fs): 25.95 HzElectrical “Q” (Qes): 0.51Mechanical “Q” (Qms): 10.648Total Speaker “Q” (Qts): 0.479Equivalent Compliance (Vas): 2.26 cu ft / 64.00 LOne-Way Linear Excursion (Xmax)*: 0.433 in / 11 mmReference Efficiency (no): 0.23%Efficiency (1 W / 1 m)**: 85.51 dB SPLEffective Piston Area (Sd): 98.26 sq in / 0.0634 sq mDC Resistance (Re): 2.100 Ω* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690 are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, 1-inch aluminium dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 39 Hz – 22 KHz ± 3 dB WOOFER PHYSICAL SPECIFICATIONS: Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 2.75 in / 70 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from the mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.97 in / 50 mm Surface Mount Fixture Diameter (A2): 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B): 1.75 in / 45 mm Flush Mount Mounting Depth (C): 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.87 in / 22 mm CROSSOVER PHYSICAL SPECIFICATIONS: Depth (D): 1.34 in / 34 mm Height (H): 0.90 in / 23 mm Width (W): 1.96 in / 50 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many “6-inch” speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 91.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 59 Hz – 22 kHz ± 3 dB Frame Outer Diameter* (A): 6.5 in / 165 mm Grille Tray Outer Diameter (B): 6.84 in / 174 mm Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion** (E): 0.85 in / 22 mm Mounting Hole Diameter (F): 5.56 in / 141 mm Mounting Depth (G): 2.44 in / 62 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.87 in / 48 mm Surface Mount Fixture Diameter (A2): 1.69 in / 43 mm Flush Mount Mounting Hole Diameter (B): 1.625 in / 41 mm Flush Mount Mounting Depth (C): 0.76 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.29 in / 7 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.92 in / 23 mm CROSSOVER PHYSICAL SPECIFICATIONS: Width (W): 1.96 in / 50 mm Height (H): 0.90 in / 23 mm Depth (D): 1.34 in / 34 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with dual true, edge-driven, aluminium dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension. Both high-frequency drivers also benefit from the damping of a silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 36 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.94 in / 100 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 3.09 in / 79 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many “6-inch” speaker locations as well. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 48 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.25 in / 159 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 5.02 in / 128 mm Mounting Depth (G): 2.07 in / 53 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included, allowing the C1-570x to be installed in bottom-mount applications. The speaker baskets are also equipped with slotted mounting holes to fit into 6 x 8-inch factory speaker locations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-570x are a proprietary, stamped, steel 5 x 7-inch (125 x 180 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 40 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.50 x 7.63 in / 140 x 194 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.46 in / 12 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 2.46 in / 63 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 54 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.83 in / 132 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.54 in / 14 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 4.70 in / 119 mm Mounting Depth (G): 2.42 in / 62 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 35 W Peak Music Power: 105 W Recommended Amplifier Power (RMS): 10 – 50 W / Ch. System Efficiency: 84.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 64 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 4.03 in / 102 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.33 in / 59 mm Frontal Coaxial Tweeter Protrusion** (D): 0.61 in / 16 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 3.70 in / 94 mm Mounting Depth (G): 1.81 in / 46 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Made in the USA with Global Components Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert DESIGN FEATURES: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high-frequency behaviour. Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw’s outstanding excursion capability. Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver’s performance range. A 32 mm (1.27 inch) diameter, the overhung voice coil is employed, wound with copper wire onto a fibreglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area and our patented Elevated Frame Cooling technology. DESIGN BANDWIDTH: With 48 dB/octave filters: 50 Hz – 5 kHz With 24 dB/octave filters: 60 Hz – 5 kHz With 12 dB/octave filters: 70 Hz – 5 kHz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 125 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 50 - 175 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 50 Hz - 5 KHz ± 3 dB Voice Coil Resistance (Re): 3.114 Ω Free Air Resonance (Fs): 54.5 Hz Reference Efficiency (no): 0.304% Efficiency: 87.0 dB @ 1W / 1m | 93.0 dB @ 1W / 0.5m Sensitivity: 90.0 dB @ 2.83V / 1m Electrical “Q” (Qes): 0.669 Mechanical “Q” (Qms): 6.265 Total Speaker “Q” (Qts): 0.605 Equivalent Compliance (Vas): 0.461 cu. ft. (13.05 liters) Moving Mass (Mms): 17.679 g Mechanical Compliance (Cms): 0.000482 m/N Magnetic Strength (BL): 5.31 N/A Effective Piston Area (Sd): 21.4 sq. in. (0.013807 sq. m) One Way Linear Excursion (Xmax): 5 mm

JL Audio’s patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output. In the HO112-W6v3, the high power handling of the 12W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification. JL Audio’s patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer’s direct output. This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 12W6v3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer. A steel mesh woofer grille insert can be purchased separately (Model: SGR-12W6v2/v3) if additional woofer protection is desired. GENERAL SPECIFICATIONS: Finish: Dark grey, high-grade automotive carpet, with black carpet on woofer baffle “JL AUDIO” is embroidered in silver on the side surface of the enclosure Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 600W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 600 W System Nominal Impedance 2 Ω Enclosure Type Chamber-coupled, slot-ported, rear-firing design Finish Dark grey carpet with black insert Grille Included: No External Width (W) 14.5 in / 368 mm External Height (H) 16 in / 406 mm External Depth (D1) 24 in / 610 mm Net Weight 60.7 lb / 27.52 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle A steel mesh grille is included to protect the subwoofer driver Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 – 250W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 250 W Enclosure Type Slot-ported, Low-profile Finish Black carpet External Width (W) 18.625 in / 473 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm Net Weight 17.40 lb / 7.89 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 6W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on the front baffle Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 50 – 150W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 150 W Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh External Width (W) 14.125 in / 359 mm External Height (H) 9.625 in / 245 mm External Depth (D1) 5.125 in / 130 mm Net Weight 12 lb / 5.44 kg

Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1000/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately). GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Height (H) 2.13 in / 54 mm Width (W) 14.66 in / 372 mm Depth (D) 6.96 in / 177 mm

Steel mesh grille insert for select JL Audio 13-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 12-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for select JL Audio 12-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 10-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for select JL Audio 10-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for the 6W3v3 subwoofer driver. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer's grille receiver ring.

Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is our proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion. For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Height (H): 2.13 in / 54 mm Width (W): 9.78 in / 248 mm Depth (D): 6.96 in / 177 mm

The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs. By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Six (Front/Rear/Sub Output Pairs) Analog Output Unbalanced, stereo RCA jacks Digital Output N/A Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100 or DRC-200) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control) Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω  

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its dual 8W3v3 subwoofer drivers, each in separate airspace, with an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port for each driver wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The two flared port entries/exits, one on each end of the enclosure, further enhance sound quality by minimizing air-flow noises through these ports. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle Steel mesh grilles are included to protect the subwoofer drivers Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 500W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 500 W Enclosure Type Slot-ported, Low-profile External Width (W) 35.5 in / 902 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 250WNominal Impedance: 4 Ω

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-690tx system features 6 x 9-inch (150 x 230 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6 x 9-inch (150 x 230 mm) format is a direct fit in many vehicles. The Mid-Range driver is ferrofluid-cooled, with a 2-inch Mylar® cone diaphragm to smoothly bridge the gap between the woofer and the dome tweeter. Tweeters are mounted next to the mid-range driver and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 70 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 125 W / Ch. System Efficiency 93 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-650x system features 6.5-inch (165 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. Many people mistakenly believe that an oval speaker cannot perform as well as around one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C2-570x system features 5 x 7 / 6 x 8-inch (125 x 180 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Grilles are not available for this speaker system. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-525x system features 5.25-inch (130 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-400x system features 4-inch (100 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Breakaway mounting tabs on the woofer frame allow the C2-400x to be installed in four-hole or two-hole configurations. Injection-moulded adaptor plates are also included to allow mounting of the C2-400x speakers into a 4 x 6 (100 x 150 mm) speaker location. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 35 W Peak Music Power 105 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 84.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 71 Hz - 22 KHz ± 3 dB

The 12W7AE brings serious performance to the table by combining the breakthrough of the long-excursion W7 design with a large 12-inch bore. It has been called "addictive," "seductive" and "the new subwoofer reference", by some of the world's toughest reviewers, and has earned these accolades by delivering nearly limitless dynamics, exceptional balance and world-class sound quality. This potent driver is best used with amplifier power in the 400W - 1000W range and is optimized to operate in a 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but are they distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label Continuous Power Handling (RMS) 1000 W Recommended Amplifier Power (RMS) 400 - 1000 W Nominal Impedance (Znom) 3 Ω

This subwoofer driver has been called the "best damn 8-inch subwoofer ever made" for its remarkable performance capabilities and design attributes. An impressive linear excursion envelope that exceeds 0.75 in. (19 mm) one-way allows it to deliver impact well beyond the range of other 8-inch subwoofer drivers. The 8W7AE is best used with amplifier power in the 200W - 500W range and is optimized to operate in a 0.875 cu. ft. (24.8 l) sealed enclosure, or a 1.0 cu. ft. (28.3 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 200 - 500 W Nominal Impedance (Znom) 3 Ω

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-600x system features 6-inch (150 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6-inch (150 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair.

JL Audio patented thin-line woofer technology compresses the architecture of the 13TW5v2 using a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the speaker than with conventional designs, while allowing excellent linear excursion capability and mechanical stability. To unleash even more performance from this technology, the v2 improves upon the original 13TW5 with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is also available in single 2 ohm and si4-ohm4 ohm voice coil versions to fit a wide range of applications. In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 10-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer. The 13TW5v2 is best used with amplifier power in the 250W - 600W range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure.

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Deep, powerful and accurate JL Audio bass is now possible in more applications than ever. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability. The 12W3v3-4 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 1.125 cu. ft. (31.8 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 4 Ω