Car Audio Upgrades and Sound System Enhancements

FEATURES: JLid™ Bluetooth® Communicator for VXi Amplifiers Tune your VXi amplifier via a Bluetooth device Not for Streaming or Hands Free

Monoblock Class D Subwoofer Amplifier, 500 W x 1 @ 2 Ω / 250 W x 1 @ 4 Ω - 14.4V Designed to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the JD500/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion. The JD500/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.  The JD500/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 250 W RMS x 1 @ 3 Ω 350 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 225 W RMS x 1 @ 3 Ω 300 W RMS x 1 @ 2 Ω 400 W RMS x 1 @ 1.5 Ω N/A   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™)   Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.10 in / 53 mm Width (W) 9.50 in / 242 mm Depth (D) 7.50 in / 190 mm Net Weight

The VXi amplifier ecosystem is designed to be very flexible, offering users almost limitless combinations of amplifiers and channel architectures, along with the amazing power of its integrated DSP technology. VXi-HUB is an accessory designed to simplify the control of a networked amplifier system, while greatly easing the setup process, by allowing all amplifiers to appear in a single TüN™ software session. VXi-HUB performs two distinct functions as part of a system employing two or more VXi amplifiers: data networking and digital audio distribution. Data networking is the primary function of the VXi-HUB, permitting a network of VXi amplifiers to respond to synchronized commands from a single DRC controller (DRC-100, DRC-200 or DRC-205, all sold separately). These commands can include Master Volume, Subwoofer Level, Fader, Zone Level and Preset Selection. The VXi-HUB also enables the networked VXi amplifiers to be tuned from within a single TüN™ software session, allowing the user to quickly switch between amplifiers during the tuning process, without disconnecting and connecting multiple cables. For data networking purposes, the VXi-HUB is equipped with one Master and five Slave JLid-COMM connections, permitting the networking of up to six VXi amplifiers using standard CAT5e cables (one master amplifier and five slave amplifiers). For more complex systems, two VXI-HUBs can be daisy-chained to create a network of up to ten VXi amplifiers (one master amplifier and nine slave amplifiers). VXi-HUB also includes a dedicated JLid-COMM accessory port to allow the connection of the optional VXi-BTC Bluetooth® Communicator (sold separately). This accessory enables convenient wireless setup and tuning of the entire amplifier network using a compatible iOS® or Android® device with TüN™ Mobile or TüN™ Express apps. The secondary function of the VXi-HUB is to distribute synchronous optical digital audio signals to the networked amplifiers, avoiding the delays associated with handing digital signals off through a chain of amplifiers. The optical digital audio output of a source unit connects directly to the VXi-HUB’s Optical Audio Input, which then distributes synchronous digital audio to the amplifiers from its five Optical Outputs. VXi-HUB handles S/PDIF signals up to 24 bits/192 kHz. For ease of connection, the VXi-HUB is powered via the JLid™ connection to VXI amplifiers and requires no separate power or turn-on wiring. FEATURES: JLid-COMM Connections: 1 Master Input / 5 Slave Outputs / 1 Accessory Port Optical Audio (S/PDIF) Connections: 1 Input / 5 Synchronous Outputs 3-way Configuration Switch: Standalone / Primary / Secondary Amp Identifier Status LEDs Powered via JLid™ connection to VXi amplifiers

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX400/4i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up to 200 W x 2. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 4 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness 6 ft A/B USB Cable

JL AUDIO CP210-W0V3 DUAL 10W0V3 BASSWEDGE, PORTED, 2 Ω Product highlights •Dual 10" 10W0v3-4 Loaded Ported Enclosure • 1200W Peak • 600W RMS • Top-Quality MDF Construction • Durable Dark Gray Carpet Finish • Five-Way Binding Post Connectors • Embroidered JL Audio Logo Subwoofer Features Dual 10" W0v3 Series Subwoofer Manufacturer preloaded with a JL Audio 10W0v3-4 10" Subwoofer, JL Audio's best-selling subwoofer! Power Handling:RMS: 600 watts Recommended Power Range: 150 - 600 watts Impedance: 2-Ohm Mineral-filled, polypropylene cone woofer for excellent durability Large roll surround for generous amounts of excursion Elevated frame cooling brings air directly to the voice coil Designed for compact sealed enclosures or medium-sized ported enclosures Large excursion for louder bass and less distortion DMA Optimized motor system reduces distortion and tight, clean bass Lead wire woven into spider for added strength Metallic silver frame finish 2.0" High temperature voice coil Free Air Resonance (Fs): 32.09 Hz Sensitivity: 84.07 dB Xmax: 11.4 mm Reference Efficiency (no): 0.1500% Frequency response: ~26 ~ 250 Hz Black Steel-Mesh Grille Insert Available: JL Audio SGRU-10 Matching Amplifier: JL Audio XD600/1v2 JL Audio JX500/1D Authorized Internet Dealer 2 Year Manufacturer's Warranty Enclosure Features: 10" Slot Ported MDF Subwoofer Enclosure Loaded with two 10W0v3 10" subwoofers Designed for forward, rear or down-firing installation Top-quality MDF construction Durable dark gray carpet finish Five-Way binding post connectors Embroidered JL Audio logo Embroidered "Slot-Ported BassWedge" logo on port mouth 2 Ohm final impedance Dimensions: 17-1/2"TD x 14"BD x 29-5/8"W x 13-7/8"H JL Model ComparisonFrom entry level woofers to competition grade, JL has them all. Let us find which one works for you. Model RMS Power Cone Material Surround Material Sensitivity (dB) Frequency Response Xmax (mm Terminals Made In America W7 Series 500-1500 Watts Polypropylene Foam Overroll 82.7 - 86.3 15-250 Hz 19-32 Push Terminals Yes W6 Series 600 Watts Polypropylene Rubber 82.7 - 85.4 20-200 Hz 19 Push Terminals Yes W3 Series 150-600 Watts Polypropylene Rubber 80.5-87.90 20-250 Hz 8.89-15.5 Push Terminals Yes W1 Series 150-300 Watts Polypropylene Rubber 83.9-86.1 22-200 8-11 Push Terminals W0 Series 300-500 Watts Polypropylene Foam 84-88.20 20-250 Hz 11.4-12.7 Push Terminals WX Series 200 Watts Polypropylene Foam 86-87.17 22-250 Hz 10 Spade Terminals

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX600/6i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up a rock-solid 200 W x 3. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 4 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness 6 ft A/B USB Cable

NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX800/8i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms to deliver a powerful 200 W x 4. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harnesses (2) 6 ft A/B USB Cable

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. Employing our second-generation NexD2™ amplifier technology, the VX1000/5i efficiently powers a complete audio system. It can drive four main speakers with 75 W x 4 @ 4 ohms while also powering a subwoofer with up to 600W @ 2 ohms. Bridging the main channels converts it into a very powerful, 3-channel system amplifier with up to 200W x 2 @ 4 ohms on the main channels and 600W @ 2 ohms on the subwoofer channel. The NexD2™ full-range technology in the main channels of this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The subwoofer channel features an optimized low-frequency variant of the NexD2™ technology. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness Subwoofer Output Connector 6 ft A/B USB Cable

Enclosed Subwoofer System with Single 10W0v3-4 Subwoofer, Dark Gray Carpet (300 W, 4 Ω) - Ported Enclosure This powerful slot-ported BassWedge™ subwoofer system delivers awesome output at an unsurpassed value. The slot-port runs along the bottom of the enclosure and fires on the same plane as the woofer to produce excellent extension and response smoothness. The port mouth is flared to minimize air-flow noises. The ultra-versatile BassWedge™ shape has extended sides so that it can be placed with the woofer firing out or straight down, off the floor of the vehicle. The shape works equally well in forward or rear-firing installations. This gives you plenty of options for tweaking the loading of the enclosure into your vehicle. This subwoofer system is shipped wired, loaded and ready to connect via a push-button terminal. Finish: Dark gray, high-grade automotive carpet with "JL AUDIO" embroidery on the top edge and "Slot-Ported BassWedge™" embroidered on the port mouth. Construction: MDF Recommended amplifier power: 75 - 300WNominal Impedance: 4 Ω   General Specifications Continuous Power Handling (RMS) 300 W System Nominal Impedance 4 Ω Enclosure Type Slot-ported Finish Gray carpet Grille Included No   Physical Specifications External Width (W) 15.51 in / 394 mm External Height (H) 13.77 in / 350 mm External Depth (D1) 17.38 in / 441 mm External Top Surface Depth (D2) 14 in / 356 mm Net Weight 29 lb / 13.15 kg

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω  

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 250WNominal Impedance: 4 Ω

While extremely compact, this amazing amplifier will comfortably drive a complete high-performance car audio system: that is, four satellite speaker systems and a subwoofer system... with a very serious 900 watts of power! Using our Single Cycle Control switching design and R.I.P.S. technology, the HD900/5 delivers 100 W x 4 to its four main channels, plus a very meaty 500 W to its subwoofer channel. Thanks to R.I.P.S., high power can be delivered over a wide range of load impedances, while the tight power supply regulation keeps distortion down, maximizing sound quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. Main Channels @ 4 Ω 100 W RMS x 4 Main Channels @ 3 Ω 75 W RMS x 4 Main Channels @ 2 Ω 75 W RMS x 4 Main Channels @ 1.5 Ω 75 W RMS x 4 Main Channels - Bridged @ 8 Ω 200 W RMS x 2 Main Channels - Bridged @ 4 Ω 150 W RMS x 2 Subwoofer Channel @ 4 Ω 500 W RMS x 1 Subwoofer Channel @ 3 Ω 500 W RMS x 1 Subwoofer Channel @ 2 Ω 500 W RMS x 1 Subwoofer Channel @ 1.5 Ω 500 W RMS x 1

JL Audios most powerful HD amplifier employs our advanced Single-Cycle Control switching design and R.I.P.S. technology to deliver 1200 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. While targeted primarily to subwoofer applications, the HD1200/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. @ 4 Ω 1200 W RMS x 1 @ 3 Ω 1200 W RMS x 1 @ 2 Ω 1200 W RMS x 1 @ 1.5 Ω 1200 W RMS x 1

This ultra-compact monoblock amplifier employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 750 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. While targeted primarily to subwoofer applications, the HD750/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. @ 4 Ω 750 W RMS x 1 @ 3 Ω 750 W RMS x 1 @ 2 Ω 750 W RMS x 1 @ 1.5 Ω 750 W RMS x 1

JL AUDIO SB-TE-YG1/10TW1 TESLA MODEL Y STEALTHB OVERVIEW Tesla’s popular compact crossover delivers quick acceleration and a roomy cabin with plenty of space for both people and cargo. Sadly though, the factory audio options offer very little to satisfy in the bass reproduction departmen 10TW-1 SUBWOOFERS Featuring an all-fiberglass, custom-formed, sealed enclosure, this Stealthbox® houses an innovative. 10-inch TW1 thin-line subwoofer. Designed to drop into the driver’s side, rear storage compartment, this Stealthbox® solution produces amazing amounts of deep bass output, while practically vanishing into its surroundings. BUILT IN USA At a time when most audio products are built overseas, JL Audio’s commitment to in-house loudspeaker production continues to grow. To pull this off in a competitive world market, our production engineering team has created one of the world’s most advanced loudspeaker assembly facilities and established a global network of quality component suppliers who build to our specifications. This, combined with our commitment to state-of-the-art assembly technology, allows our skilled workforce to efficiently build JL Audio products to extremely high quality standards, right here in the U.S.A. INSTALL NOTES Use of driver's side, rear storage compartment is lost with installation. SPECIFICATIONS 2020-UP TESLA MODEL Y (5-SEAT) SUBWOOFERS 10TW1-2 POWER 300W RMS NOMINAL IMPEDANCE 2Ω MONO FEATURES BRAND JL AUDIO RMS POWER 300W RMS SHALLOW MOUNT YES SUBWOOFER SIZE 10"  

This compact multi-channel powerhouse employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 150 W x 4 or 300 W x 2. Tight power supply regulation keeps distortion down and maximizes sound quality. When using the HD750/1 or HD1200/1 to drive a subwoofer system, the HD600/4 is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. It can also be deployed on its own as a very capable 3-channel system amplifier with 150 W x 2 to the satellites and 300 W x 1 to a subwoofer system. This amplifier features a brushed aluminum finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.

The HD-RLC remotely controls the Bass Level of the following JL Audio amplifiers: HD-Series: All modelsXD-Series: All modelsMHD-Series: All modelsM-Series: All models When the HD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The HD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable.

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included, allowing the C1-570x to be installed in bottom-mount applications. The speaker baskets are also equipped with slotted mounting holes to fit into 6 x 8-inch factory speaker locations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-570x are a proprietary, stamped, steel 5 x 7-inch (125 x 180 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 40 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.50 x 7.63 in / 140 x 194 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.46 in / 12 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 2.46 in / 63 mm

Focal Inside Mazda BT-50 6.0 Audio Upgrade Pack - IS FORD 165 + IC FORD 165 + Impulse 4.320 - MAZDA-BT50-6.0-PACK Upgrade your Mazda BT-50's factory sound system with the Focal Inside Mazda BT-50 6.0 Audio Upgrade Pack, a complete Plug & Play solution designed to deliver clearer vocals, stronger bass response, improved detail, and greater overall audio performance without compromising your vehicle's factory appearance. Specifically developed for compatible Mazda BT-50 models, this premium audio package combines Focal's renowned IS FORD 165 component speakers, IC FORD 165 coaxial speakers, and the powerful Impulse 4.320 compact digital amplifier. Together, these components create a balanced, dynamic sound system capable of delivering exceptional clarity and listening enjoyment whether you're commuting, touring, towing, or heading off-road. The front sound stage is enhanced by the IS FORD 165 component speaker system, featuring Polyglass cone technology and aluminium inverted dome tweeters for accurate vocals, detailed midrange reproduction, and crisp high frequencies. Rear passengers benefit from the IC FORD 165 coaxial speakers, providing improved tonal balance and a fuller cabin sound experience. Powering the system is the Focal Impulse 4.320 compact digital amplifier, delivering 4 x 55W RMS for greater speaker control, cleaner output, improved dynamics, and enhanced performance at higher listening volumes. Key Features Complete Plug & Play audio upgrade for Mazda BT-50 Premium Focal speaker and amplifier package Improves clarity, bass response, and overall sound quality Front component speakers for enhanced sound staging and detail Rear coaxial speakers for balanced cabin audio Compact digital amplifier delivers clean and powerful output Maintains factory appearance and OEM integration No major modifications required on compatible vehicles Ideal for touring, towing, work, and daily driving applications What's Included IS FORD 165 – 2-Way Component Speaker Kit (Front) IC FORD 165 – 2-Way Coaxial Speaker Kit (Rear) Impulse 4.320 – Compact 4-Channel Digital Amplifier Why Upgrade Your Mazda BT-50 Audio? While the Mazda BT-50 is built for reliability, work, and adventure, the factory audio system can often lack the clarity, power, and refinement many drivers expect. This Focal Inside upgrade package addresses those shortcomings by upgrading the most important components of the audio system. The combination of premium speakers and dedicated amplification creates a more immersive listening experience with improved vocals, stronger bass, greater detail, and better balance throughout the cabin. Benefits Clearer vocals and improved speech intelligibility Enhanced bass response and musical depth Greater detail and instrument separation Improved performance at higher volume levels Balanced front and rear sound reproduction OEM-style installation and appearance Designed specifically for Mazda BT-50 applications Installation Notes Designed for compatible Mazda BT-50 vehicles Suitable for vehicles without factory amplified or premium audio systems Factory head unit integration supported Aftermarket head unit installations may require additional wiring accessories Professional installation recommended Vehicle compatibility should be confirmed before purchase Pack Summary Vehicle Mazda BT-50 Pack Type Powered Speaker Upgrade Pack Front Speakers IS FORD 165 Component Speakers Rear Speakers IC FORD 165 Coaxial Speakers Amplifier Impulse 4.320 Compact Digital Amplifier Amplifier Output 4 x 55W RMS Installation Type Plug & Play Integration SKU MAZDA-BT50-6.0-PACK