Car Audio Upgrades and Sound System Enhancements

Two-way Component System: 6.5" (165 mm) Woofer, 1" (25 mm) Silk Dome Tweeter   Born from shared technologies used in our flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grilles C6 Tweeter Features:• Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General SpecificationsContinuous Power Handling (RMS)    100 WRecommended Amplifier Power (RMS)    25 - 150 W / Ch.System Efficiency    87.37 dB @ 1 W / 1 mSystem Nominal Impedance    4 ΩSystem Frequency Response    53 Hz – 21 KHz ± 3 dB   Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.11 in / 54 mm Flush Mount Mounting Hole Diameter (B) 1.85 in / 47 mm Flush Mount Mounting Depth (C) 1.85 in / 47 mm Flush Mount Protrusion (D1) 0.30 in / 8 mm Surface Mount Protrusion (D2) 1.04 in / 26 mm Crossover Physical Specifications Width (W) 3.36 in / 85 mm Height (H) 1.44 in / 37 mm Depth (D) 4.72 in / 120 mm

Monoblock Class D Subwoofer Amplifier, 1500 W x 1 @ 1 - 2 Ω / 750 W x 1 @ 4 Ω - 14.4V Engineered for high-power, subwoofer applications, the RD1500/1 monoblock amplifier is built to deliver staggering amounts of world-class bass output. Equipped with a special low impedance circuit, the RD1500/1 is capable of generating a whopping 1500 watts of output power, at either 1 or 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1500 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1200 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >82 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1100 / 50 Hz Damping Factor @ 2 Ω >550 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 2 AWG wire Fuse Rating 150A (AFS or AGU)   Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.13 in / 54 mm Width (W) 18.05 in / 458 mm Depth (D) 6.96 in / 177 mm Net Weight

Monoblock Class D Subwoofer Amplifier, 1000 W x 1 @ 2 Ω / 600 W x 1 @ 4 Ω - 14.4V Designed to produce a serious 1000 watts into 2 ohms (14.4V, 1% THD), the JD1000/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion. The JD1000/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.  The JD1000/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.] Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 600 W RMS x 1 @ 3 Ω 800 W RMS x 1 @ 2 Ω 1000 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 500 W RMS x 1 @ 3 Ω 650 W RMS x 1 @ 2 Ω 800 W RMS x 1 @ 1.5 Ω N/A   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.10 in / 53 mm Width (W) 11.40 in / 290 mm Depth (D) 7.50 in / 190 mm Net Weight

JL AUDIO JL AUDIO JD400/4 400W RMS JD SERIES CLASS-D 4-CHANNEL AMPLIFIER Premium Engineering Utilizing our exclusive NexD™ high-speed switching technologies, the JD400/4 amplifier is engineered to deliver loads of clean power, with excellent efficiency and low distortion. This little guy churns out 100 watts of audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms. The JD400/4’s controls can be found on the input panel of the amplifier, with all speaker and power connections located along the opposite end of the extruded aluminum chassis. Signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting line-level or speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment. Onboard LED-clipping indicators are also included surrounding each input sensitivity control. This convenient feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. You will also find a set of buffered, pass-through preamp outputs on-board, so you can pass signals to another amplifier. NexD Switching Technology Let's get a little nerdy... A traditional PWM switching amp design uses a fixed switching frequency and varies the pulse width based solely on the audio input signal to the pulse modulator. This basic approach assumes some ideal conditions, like a rock-steady power supply, that do not necessarily occur in a real, in-car installation. Power supply sag with signal causes distortion at all power levels with these designs, even well below clipping. The cure for this is feedback (a corrective signal sent back to the input side), but this becomes impractical as the audio frequency increases, making it a good solution for band-limited (subwoofer) amps, but not for full-range amplifiers. Taking the above into account when designing the NexD™ subwoofer amplifiers, we have taken the simple fixed PWM approach and enhanced it with a very high switching frequency: 240 kHz, which is about 4x higher than most Class D subwoofer amplifiers. This pushes the amplifier's bandwidth to at least 500 Hz with minimal distortion and improves efficiency, while keeping typically bulky circuity more compact. Your subwoofers will reward you with tight, rock-solid bass performance. For the full-range NexD™ amplifiers and channels we applied a variable, ultra-high speed version of the NexD™ technology (switching at well over 400 kHz). In these designs, a self-oscillating modulator with "feed-forward" sends information about the instantaneous power supply voltage to the modulator, combining this with the input signal to cancel out any distortion due to supply voltage fluctuation. This reduces distortion prior to applying feedback, simplifying the overall feedback loop design. Differential-Balanced Inputs Today’s vehicles are equipped with sophisticated electronics capable of generating noise and interference that can intrude into the audio path, ruining the listening experience. Most audio equipment uses single-ended, ground-referenced RCA jacks to receive audio signals. This means that the RCA shield is connected directly to the signal ground. This is a simple, cost-effective input design that works well for short runs in noise-free environments. In noisier environments, this method cannot reject the common mode noise that could be on both RCA conductors (shield and center conductor). By having more than one chassis-grounded RCA shield on a device, single-ended input designs are also more susceptible to ground loops. If noise is present on both conductors while the shield is connected to ground, the input amplifier will amplify the noise relative to the grounded RCA shield. When there are multiple RCA connections or any other conductors subjected to a magnetic field, this will cause a difference in potential across the RCA loop to be amplified at the grounded RCA as noise (a classic ground loop). JL Audio’s Differential-Balanced Input circuits measure the center pin of the RCA connection relative to the RCA shield, even when the shield is not connected to ground, and even when the voltages at both conductors are moving relative to ground. Because both the center conductor and the shield see high impedance to ground at the input, a ground loop cannot be formed, as there is no current flow to induce a voltage as noise. This works equally well with differential-balanced, or unbalanced signal sources, making this input architecture compatible with all standard car and marine audio equipment, using standard, unshielded, twisted-pair RCA cables. No special cables are required, unlike the fully balanced connections used in professional audio. Another benefit of the Differential-Balanced Input design is that it easily accepts low-level and high-level signals from a variety of factory head unit outputs and amplifiers, including single-ended “ground referenced” sources, as well as Balanced or Unbalanced “Bridged or BTL” sources. This eliminates the need for Line Output Converters (LOCs) in most installation scenarios. The obvious question is: “Why don’t all car audio amplifiers use Differential-Balanced Inputs?” The answer is simple: it costs more. Executing a proper differential-balanced input section requires more components and better quality components than a basic single-ended design, so you generally won’t find them on less expensive amplifiers. Product Details: JD Series Class D 2 ohms Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 100 watts x 4 channel Bridged: 200 watts x 2 channel @ 4 ohms Total power output: 400 watts LED Power/Protect Light Wired bass level remote control not included Speaker-level (high-level) inputs (Requires adapter like the JL Audio XD-CLRAIC2-SW) Signal sensing remote turn-on Protection Circuitry with Status LED NextD™ switching amp technology Differential-balanced inputs help eliminate noise Advanced Rollback Protection System prevents thermal shut-down Speaker-level (high-level) inputs Input sensitivity: Low level: 200mV - 2 volts High level: 800mV - 8 volts Frequency Response: 12 - 22000 Hz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: >104 dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Fuse Rating: 40A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 9-7/8" L x 7-1/2" W x 2-1/8" H Authorized Internet Dealer 2 Year Manufacturer's Warranty MFR #: JD400/4 Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer

Steel mesh grille insert for select JL Audio 13-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 12-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 10-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for select JL Audio 10-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for the 6W3v3 subwoofer driver. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer's grille receiver ring.

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Made in the USA with Global Components Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert DESIGN FEATURES: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high-frequency behaviour. Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw’s outstanding excursion capability. Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver’s performance range. A 32 mm (1.27 inch) diameter, the overhung voice coil is employed, wound with copper wire onto a fibreglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area and our patented Elevated Frame Cooling technology. DESIGN BANDWIDTH: With 48 dB/octave filters: 50 Hz – 5 kHz With 24 dB/octave filters: 60 Hz – 5 kHz With 12 dB/octave filters: 70 Hz – 5 kHz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 125 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 50 - 175 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 50 Hz - 5 KHz ± 3 dB Voice Coil Resistance (Re): 3.114 Ω Free Air Resonance (Fs): 54.5 Hz Reference Efficiency (no): 0.304% Efficiency: 87.0 dB @ 1W / 1m | 93.0 dB @ 1W / 0.5m Sensitivity: 90.0 dB @ 2.83V / 1m Electrical “Q” (Qes): 0.669 Mechanical “Q” (Qms): 6.265 Total Speaker “Q” (Qts): 0.605 Equivalent Compliance (Vas): 0.461 cu. ft. (13.05 liters) Moving Mass (Mms): 17.679 g Mechanical Compliance (Cms): 0.000482 m/N Magnetic Strength (BL): 5.31 N/A Effective Piston Area (Sd): 21.4 sq. in. (0.013807 sq. m) One Way Linear Excursion (Xmax): 5 mm

The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs. By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Six (Front/Rear/Sub Output Pairs) Analog Output Unbalanced, stereo RCA jacks Digital Output N/A Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100 or DRC-200) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control) Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

JL Audio’s patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output. In the HO112-W6v3, the high power handling of the 12W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification. JL Audio’s patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer’s direct output. This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 12W6v3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer. A steel mesh woofer grille insert can be purchased separately (Model: SGR-12W6v2/v3) if additional woofer protection is desired. GENERAL SPECIFICATIONS: Finish: Dark grey, high-grade automotive carpet, with black carpet on woofer baffle “JL AUDIO” is embroidered in silver on the side surface of the enclosure Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 600W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 600 W System Nominal Impedance 2 Ω Enclosure Type Chamber-coupled, slot-ported, rear-firing design Finish Dark grey carpet with black insert Grille Included: No External Width (W) 14.5 in / 368 mm External Height (H) 16 in / 406 mm External Depth (D1) 24 in / 610 mm Net Weight 60.7 lb / 27.52 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its dual 8W3v3 subwoofer drivers, each in separate airspace, with an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port for each driver wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The two flared port entries/exits, one on each end of the enclosure, further enhance sound quality by minimizing air-flow noises through these ports. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle Steel mesh grilles are included to protect the subwoofer drivers Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 500W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 500 W Enclosure Type Slot-ported, Low-profile External Width (W) 35.5 in / 902 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle A steel mesh grille is included to protect the subwoofer driver Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 – 250W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 250 W Enclosure Type Slot-ported, Low-profile Finish Black carpet External Width (W) 18.625 in / 473 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm Net Weight 17.40 lb / 7.89 kg

When the RBC-1 is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. Use it as a Subwoofer level control. INCLUSIONS: Rotary control with a black ABS knob, Mounting hardware 1x 18 ft. (5.5 m) cable COMPATIBLE WITH: RD500/1 RD1000/1 RD900/5

Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1000/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately). GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Height (H) 2.13 in / 54 mm Width (W) 14.66 in / 372 mm Depth (D) 6.96 in / 177 mm

1" (25 mm) Silk Dome Component Tweeter Born from shared technologies used in our flagship C7 speakers, the C6-100ct component tweeter benefits from vast speaker design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-100ct component tweeter features an edge-driven, pure silk dome diaphragm for smooth, high-frequency performance with remarkable off-axis response and damping. A neodymium motor and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-100ct Component Tweeter Features:• Edge-driven pure-silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Design Bandwidth:With 48 dB/octave filters: 3-21 kHzWith 24 dB/octave filters: 4-21 kHzWith 12 dB/octave filters: 5-21 kHz Component tweeters are sold individually and include surface- and flush-mount fixtures and hardware. One 15 μF tweeter protection capacitor is also included.   General Specifications Continuous Power Handling (RMS) 75 W Recommended Amplifier Power (RMS) 25 - 100 W / Ch. Nominal Impedance 4 Ω Frequency Response 3 kHz - 21 KHz ± 3 dB Parameters Voice Coil Resistance (Re) 3.20 Ω Free Air Resonance (Fs) 1500 Hz Reference Efficiency (no) 0.602% Efficiency 90 dB @ 1W / 1m96 dB @ 1W / 0.5m Sensitivity 93 dB @ 2.83V / 1m Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.16 in / 55 mm Flush Mount Mounting Hole Diameter (B) 1.88 in / 48 mm Flush Mount Mounting Depth (C) 0.73 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.33 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 1.06 in / 27 mm

Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is our proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion. For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Height (H): 2.13 in / 54 mm Width (W): 9.78 in / 248 mm Depth (D): 6.96 in / 177 mm

Crafted as an all-in-one, total system solution, the RD900/5 is engineered to power a complete audio system consisting of a subwoofer + four satellite system with 900 watts of high-performance sound. Equipped with our exclusive NexD™ switching technology, this complete power package efficiently generates a potent 70 watts of crystal-clear audio into 4 ohms, plus a robust 500 watts for a subwoofer system, all from a single compact chassis. Each pair of main channels is also fully bridgeable, stoutly producing 200 watts of full-range audio bliss (into 4 ohms), creating an ultra-powerful 3-channel amplifier. Conveniently located on top of the RD900/5, you’ll find a complement of studio-grade signal processing features, all hidden beneath a removable protective cover. Each pair of main channels is equipped with a 12 dB / octave high-pass filter, with a dedicated low-pass filter for its subwoofer channel. All three crossovers offer continuously variable frequency selection from 50-500 Hz, for precise filtering. Dual-range, differential-balanced inputs are also onboard, capable of accepting most input voltage levels, plus automatic turn-on capability (via signal sensing or DC-offset sensing) for maximum versatility. LED clipping indicators are also standard equipment for each channel section. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. The RD900/5 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can conveniently control the subwoofer’s output remotely from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response (Main Channels): 12 Hz – 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel): 10 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels): >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W: >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω: >150 / 50 Hz Damping Factor @ 2 Ω: >75 / 50 Hz THD+N @ Rated Power (Main Channels): <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels): <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs: Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge: 4 AWG wire Fuse Rating: 80 A (AFS, AGU or MaxiFuse™)

Utilizing our exclusive NexD™ high-speed switching technologies, the ultra-compact RD400/4 amplifier is engineered to deliver loads of audio output power, with incredible efficiency and low distortion. Don’t let its modern styling and small size fool you though, this little powerhouse churns out 100 watts of crystal-clear audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms. For your convenience, the RD400/4’s controls can be found on top of the amplifier, beneath a protective cover, with all connections located along one side of its chassis. Studio-grade signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment, along with all-new input type switches for bridging of stereo output channels without needing to use Y-adaptors. Onboard LED-clipping indicators are also included with your RD400/4. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. You’ll also find a set of preamp outputs on-hand, so you can pass signals to another amplifier, almost effortlessly. The RD400/4 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. GENERAL SPECIFICATIONS: Frequency Response 12 Hz – 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge: 4 AWG wire Fuse Rating: 40 A (AFS, AGU or MaxiFuse™)