JL Audio
JL AUDIO 6.5" (165 Mm) Woofer 125W Rms (Sold As Each) - C7-650cw
$1,239.00
C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing.
The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours.
Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance.
Made in the USA with Global Components
Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert
DESIGN FEATURES:
Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high-frequency behaviour.
Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw’s outstanding excursion capability.
Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver’s performance range.
A 32 mm (1.27 inch) diameter, the overhung voice coil is employed, wound with copper wire onto a fibreglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area and our patented Elevated Frame Cooling technology.
DESIGN BANDWIDTH:
With 48 dB/octave filters: 50 Hz – 5 kHz
With 24 dB/octave filters: 60 Hz – 5 kHz
With 12 dB/octave filters: 70 Hz – 5 kHz
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 125 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 50 - 175 W / Ch.
Nominal Impedance: 4 Ω
Frequency Response: 50 Hz - 5 KHz ± 3 dB
Voice Coil Resistance (Re): 3.114 Ω
Free Air Resonance (Fs): 54.5 Hz
Reference Efficiency (no): 0.304%
Efficiency: 87.0 dB @ 1W / 1m | 93.0 dB @ 1W / 0.5m
Sensitivity: 90.0 dB @ 2.83V / 1m
Electrical “Q” (Qes): 0.669
Mechanical “Q” (Qms): 6.265
Total Speaker “Q” (Qts): 0.605
Equivalent Compliance (Vas): 0.461 cu. ft. (13.05 liters)
Moving Mass (Mms): 17.679 g
Mechanical Compliance (Cms): 0.000482 m/N
Magnetic Strength (BL): 5.31 N/A
Effective Piston Area (Sd): 21.4 sq. in. (0.013807 sq. m)
One Way Linear Excursion (Xmax): 5 mm
JL Audio
JL AUDIO System Tuning Dsp Controlled By Tün Software, 8-Channel Analog & Digital Inputs /...
$979.00
The TwK™ 88 is a state-of-the-art digital signal processor engineered to deliver world-class system tuning capabilities in an easy-to-use format.
Equipped with an advanced 24-bit DSP processor, the TwK™ 88 includes flexible input/output options, 80 total bands of equalization and powerful mixing tools.
The included DRC-200 Digital Remote Controller offers dual level controls, toggles up to six presets, and has an LED indicator.
Control the TwK™ 88’s entire feature set by connecting it to your PC via USB, using the companion TüN™ Software interface.
FEATURES:
Flexible input design with 8 differential-balanced, line-level analog inputs (RCA), accepting line-level signals up to 7.1V (RMS)
Separate optical (Toslink) and coaxial digital inputs for connection to digital S/PDIF sources
Flexible input mixer allows input channels to be combined with full control over each input’s level and polarity
8 banks of 10-band graphic or parametric equalizers with configurable EQ assignment
Powerful crossover section with fully variable, high-pass and low-pass filters, crossover slopes are selectable from 6 dB/octave to 48 dB/octave (in 6 dB/octave increments)
Configurable polarity and delay settings, with separate entries for speaker distance plus offset control; fully linkable with other channels, in any combination, for adjustment
Precise output level controls, adjustable in 0.5 or 0.1 dB increments, fully linkable with other channels, in any combination
8 analog, line-level RCA output jacks (4V RMS)
Optical (Toslink) output jack provides a pass-through digital audio (S/PDIF) signal from any pair of input channels, with no signal processing applied
Remote turn-on output (+12VDC) for activating aftermarket audio equipment
JLid™ Port allows connection of the included DRC-200 Digital Remote Controller to add dual configurable level controls, preset selection and LED status reporting from the driver's seat
SPECIFICATIONS:
Power Supply Type: Regulated DC-DC SMPS
Input Operating Voltage: 10 - 16 VDC
Standby Current Draw: <1.5 mA
Operating Current Draw: 0.7 A
Recommended Fuse Value: 1 A
Input Channels: 8
Input Type: Line-level, Differential-Balanced
Input Voltage Range: 250 mV - 7.1 V RMS
Minimum Input Voltage: 10 mV RMS
Input Level Setting: 11 discrete selections from 250 mV - 7.1V RMS
Output Channels: 8
Analog Output: Unbalanced, stereo RCA jacks
Digital Output: Optical (Toslink) output (S/PDIF)
Output Impedance: 450 Ω
Latency Analog - Analog: 5.425 mS
Latency Analog - Optical: 5.470 mS
Latency Optical - Optical: 4.860 mS
Latency Optical - Analog: 4.805 mS
S/N Ratio: 98 dB (A-Weighted, referred to 4V RMS Output)
THD+N @ Rated Output: 0.02% (20 Hz - 20 kHz)
Audio Resolution: 24 bit / 48 kHz
Number of EQ Bands: 10 x 8 Channels
Remote Level Control: Included (DRC-200)
Remote Level Functions: Master Volume Control + Trim; Master Volume Control + Fader; Zone Control, LED Status Reporting
JL Audio
JL AUDIO 4-Channel Load-Sensing Adaptor For Use With Fix™ 82 Or Fix™ 86 Oem Integration...
$79.00
Some factory audio amplifiers employ a load detection circuit that looks for a low-impedance load in order to enable audio output.
When a high-impedance load, like the input section of a FiX™ DSP, is connected to these factory amplifiers, the audio signal will mute.
The FiX-LSA-4 is designed to provide a low enough load impedance to enable audio output in most of these situations. Simply disconnect the input connectors from the FiX™ DSP, insert the FiX-LSA-4 in-line and recalibrate with the FiX-LSA-4 in place.
Note: An additional FiX-LSA-4 will be necessary if your FiX™ is connected to more than four channels of audio from your OEM head unit or amplifier.
JL Audio
JL AUDIO Oem Integration Dsp With Automatic Time Correction And Digital Eq (8-Channel Inputs/4-Channel Stereo...
$889.00
The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction.
Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs.
By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well.
By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS).
Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat.
Achieving great sound from your factory stereo has never been easier, or sounded better.
GENERAL SPECIFICATIONS:
Power Supply Type Regulated DC-DC SMPS
Input Operating Voltage 10 – 16 VDC
Standby Current Draw <1.5 mA
Operating Current Draw 0.7 A
Recommended Fuse Value 1 A
Input Channels Eight
Input Type Differential-Balanced
Input Voltage Range 250 mV – 30 V RMS
Minimum Input Voltage 10 mV RMS
Input Level Setting Fully automatic
Output Channels Six (Front/Rear/Sub Output Pairs)
Analog Output Unbalanced, stereo RCA jacks
Digital Output N/A
Output Impedance 450 Ω
S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output)
THD+N @ Rated Output 0.02% (20 Hz – 20 kHz)
Audio Resolution 24 bit / 48 kHz
Number of EQ Bands 30 x 2 channels
EQ Resolution 1/3 octave (25 Hz – 20 kHz)
Remote Level Control Optional (DRC-100 or DRC-200)
Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control)
Height (H) 1.85 in / 47 mm
Width (W) 4.29 in / 109 mm
Depth (D) 6.14 in / 156 mm
Net Weight 2.58 lb / 1.17 kg
JL Audio
JL AUDIO Oem Integration Dsp With Automatic Time Correction & Digital Eq (8-Channel Inputs/2-Channel Stereo...
$709.00
The FiX™ 82 is a state-of-the-art digital signal processor engineered to deliver world-class sound from factory audio systems, without replacing the OEM source unit.
The FiX™ 82 is the first DSP to automatically correct time delayed factory outputs prior to signal summing and EQ correction. With a powerful 24-bit DSP processor and dual 1/3 octave equalizers onboard, complex 2-way, 3-way and 4-way factory audio outputs are combined and level-matched automatically into a flat, full-range stereo signal.
Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Calibration is initiated with just a single button press and takes only about 30 seconds to complete, with no special equipment needed! By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs.
Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access a pair of user-adjustable, 10-band, graphic equalizers to fine-tune the output signals.
Output options include dual RCA jacks (4V RMS) or a digital optical (Toslink) output, supporting PCM audio (S/PDIF) at 24 bit/48 kHz resolution. Activation methods include 12-volt or automatic (Signal/DC-Offset Sensing), plus a dedicated remote turn-on output for activating your aftermarket equipment.
Connect the optional DRC-100/205 Digital Remote Controller (sold separately) to add Master Volume Control capabilities from the driver’s seat. Clipped input signals and overall condition are also reported via the DRC-100’s multi-colour status LED. Achieving great sound from your factory stereo has never been easier, or sounded better.
GENERAL SPECIFICATIONS:
Power Supply Type Regulated DC-DC SMPS
Input Operating Voltage 10 – 16 VDC
Standby Current Draw <1.5 mA
Operating Current Draw 0.7 A
Recommended Fuse Value 1 A
Input Channels Eight
Input Type Differential-Balanced
Input Voltage Range 250 mV – 30 V RMS
Minimum Input Voltage 10 mV RMS
Input Level Setting Fully automatic
Output Channels Two
Analog Output Unbalanced, stereo RCA jacks
Digital Output Optical (Toslink) output (S/PDIF)
Output Impedance 450 Ω
S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output)
THD+N @ Rated Output 0.02% (20 Hz – 20 kHz)
Audio Resolution 24 bit / 48 kHz
Number of EQ Bands 30 x 2 channels
EQ Resolution 1/3 octave (25 Hz – 20 kHz)
Remote Level Control Optional (DRC-100)
Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting
Height (H) 1.85 in / 47 mm
Width (W) 4.29 in / 109 mm
Depth (D) 6.14 in / 156 mm
Net Weight 2.58 lb / 1.17 kg
JL Audio
JL AUDIO Stealthbox For Toyota Landcruiser Wagon 86 (2016 - Up) & Subaru Brz (2013...
$1,769.00
Somebody finally paid attention and designed a no-nonsense, back-to-basics sports car that puts the emphasis on driving enjoyment.
Now all you need to do is add a healthy dose of JL Audio to ratchet up the listening enjoyment and make every drive even more memorable.
Our patented 10TW3 thin-line driver is the engine inside this Stealthbox® system, and it produces spectacular results from its perch in the passenger side rear corner of the trunk.
Your trunk remains completely useful and your installation is neat and secure.
A grille is also included to protect your investment.
GENERAL SPECIFICATIONS:
Contains one 10TW3-D4 subwoofer in a sealed enclosure
400-watt power handling
Wired for 2-ohm mono
Installs in the passenger side of the trunk compartment
Black steel mesh woofer grille is included
JL Audio
JL AUDIO Stealth Box For Ford Mustang 2015 And Onward (Does Not Fit Convertible) -...
$2,309.00
The latest all-American pony car gets a big dose of horsepower and major technology enhancements, all packaged in a new sleek and sexy body.
Sadly though, the stock audio systems just can’t deliver enough bass to keep up with the Mustang’s high-performance muscle.
Our Stealthbox® features an all-fibreglass, sealed enclosure design that fits in the same location as the optional factory subwoofer (and requires no holes to be drilled for installation).
Equipped with our revolutionary 12TW3 thin-line subwoofer, this Stealthbox delivers deep, powerful bass that’s worthy of your Mustang’s heritage.
GENERAL SPECIFICATIONS:
Contains one 12TW3-D4 in a sealed enclosure
400-watt power handling. Wired for 2-ohm mono
Installs in the passenger side rear corner of the trunk
Factory subwoofer (if equipped) must be removed for installation of Stealthbox®
Installation in Mustang Shelby GT350 models requires relocation of additional OEM equipment
Will not fit convertible models
![JL AUDIO Enclosed Subwoofer System With Single 12W6V3-D4 Subwoofer Driver, Dark Gray / Black Carpet (600 W, 2 Ω) [Ported Enclosure] - HO112-W6v3](http://tjmnorthernbeaches.com.au/cdn/shop/files/HO112-W6v3-FRT_d93de69f-65f6-4a48-a7d2-172b303246b5_10x.jpg?v=1746157717)
JL Audio
JL AUDIO Enclosed Subwoofer System With Single 12W6V3-D4 Subwoofer Driver, Dark Gray / Black Carpet...
$2,129.00
JL Audio’s patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output.
In the HO112-W6v3, the high power handling of the 12W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification.
JL Audio’s patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer’s direct output.
This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 12W6v3 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer.
A steel mesh woofer grille insert can be purchased separately (Model: SGR-12W6v2/v3) if additional woofer protection is desired.
GENERAL SPECIFICATIONS:
Finish: Dark grey, high-grade automotive carpet, with black carpet on woofer baffle
“JL AUDIO” is embroidered in silver on the side surface of the enclosure
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 200 – 600W
Nominal Impedance: 2 Ω
Continuous Power Handling (RMS) 600 W
System Nominal Impedance 2 Ω
Enclosure Type Chamber-coupled, slot-ported, rear-firing design
Finish Dark grey carpet with black insert
Grille Included: No
External Width (W) 14.5 in / 368 mm
External Height (H) 16 in / 406 mm
External Depth (D1) 24 in / 610 mm
Net Weight 60.7 lb / 27.52 kg
JL Audio
JL AUDIO Ported Dual Enclosure Fitted With 2X 8" 8W3V3 Woofers (Final Impedance 2 Ohms)...
$1,509.00
This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems.
The key to its performance lies in the precise tuning of its dual 8W3v3 subwoofer drivers, each in separate airspace, with an efficient slot-ported design.
Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port for each driver wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness.
The two flared port entries/exits, one on each end of the enclosure, further enhance sound quality by minimizing air-flow noises through these ports.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
GENERAL SPECIFICATIONS:
Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle
Steel mesh grilles are included to protect the subwoofer drivers
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 200 – 500W
Nominal Impedance: 2 Ω
Continuous Power Handling (RMS) 500 W
Enclosure Type Slot-ported, Low-profile
External Width (W) 35.5 in / 902 mm
External Height (H) 11.0 in / 279 mm
External Depth (D1) 5.125 in / 130 mm
![JL AUDIO Enclosed Subwoofer System With Single 8W3V3-4 Subwoofer Driver, Black Carpet (250 W, 4 Ω) [Ported Enclosure] - CP108LG-W3v3](http://tjmnorthernbeaches.com.au/cdn/shop/files/CP106LG-W3v3-FRT_b948064d-1d23-47c5-b03d-2efd53b04d18_10x.jpg?v=1746157722)
JL Audio
JL AUDIO Enclosed Subwoofer System With Single 8W3V3-4 Subwoofer Driver, Black Carpet (250 W, 4...
$799.00
This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems.
The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume.
The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
GENERAL SPECIFICATIONS:
Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle
A steel mesh grille is included to protect the subwoofer driver
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 – 250W
Nominal Impedance: 4 Ω
Continuous Power Handling (RMS) 250 W
Enclosure Type Slot-ported, Low-profile
Finish Black carpet
External Width (W) 18.625 in / 473 mm
External Height (H) 11.0 in / 279 mm
External Depth (D1) 5.125 in / 130 mm
Net Weight 17.40 lb / 7.89 kg
![JL AUDIO Enclosed Subwoofer System With Single 6W3V3-4 Subwoofer Drivers, Black Carpet (150 W, 4 Ω) [Ported Enclosure] - CP106LG-W3v3](http://tjmnorthernbeaches.com.au/cdn/shop/files/CP106LG-W3v3-FRT_fb2eefeb-1b1b-4d48-8389-8b42bc178598_10x.jpg?v=1746157725)
JL Audio
JL AUDIO Enclosed Subwoofer System With Single 6W3V3-4 Subwoofer Drivers, Black Carpet (150 W, 4...
$709.00
This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems.
The key to its performance lies in the precise tuning of its 6W3v3 subwoofer driver into an efficient slot-ported design.
Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness.
The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
GENERAL SPECIFICATIONS:
Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on the front baffle
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 50 – 150W
Nominal Impedance: 4 Ω
Continuous Power Handling (RMS) 150 W
Enclosure Type Slot-ported, Low-profile
Finish Black carpet
Grille Included Black Steel Mesh
External Width (W) 14.125 in / 359 mm
External Height (H) 9.625 in / 245 mm
External Depth (D1) 5.125 in / 130 mm
Net Weight 12 lb / 5.44 kg
JL Audio
JL AUDIO Remote Bass Control For Rd Series Rd500/1, Rd1000/1 & Rd900/5 Amplifiers - RBC-1
$99.00
When the RBC-1 is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. Use it as a Subwoofer level control.
INCLUSIONS:
Rotary control with a black ABS knob,
Mounting hardware
1x 18 ft. (5.5 m) cable
COMPATIBLE WITH:
RD500/1
RD1000/1
RD900/5
JL Audio
JL AUDIO Monoblock Class D Subwoofer Amplifier, 1000 W X 1 @ 2 Ω /...
$989.00
Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD).
At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion.
For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels.
Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1000/1 is also equipped with an onboard LED-clipping indicator.
This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed.
The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition.
Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).
GENERAL SPECIFICATIONS:
Frequency Response 7 Hz – 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Damping Factor @ 4 Ω >1000 / 50 Hz
Damping Factor @ 2 Ω >500 / 50 Hz
THD+N @ Rated Power <1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge 4 AWG wire
Fuse Rating 80 A (AFS, AGU or MaxiFuse™)
Height (H) 2.13 in / 54 mm
Width (W) 14.66 in / 372 mm
Depth (D) 6.96 in / 177 mm
JL Audio
JL AUDIO Monoblock Class D Subwoofer Amplifier, 500 W X 1 @ 2 Ω /...
$669.00
Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis.
The secret behind its power proficiency is our proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion.
For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ.
Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.
The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition.
With the addition of RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat.
GENERAL SPECIFICATIONS:
Frequency Response 7 Hz – 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Damping Factor @ 4 Ω >1000 / 50 Hz
Damping Factor @ 2 Ω >500 / 50 Hz
THD+N @ Rated Power <1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge 4 AWG wire
Fuse Rating 50 A (AFS, AGU or MaxiFuse™)
Height (H): 2.13 in / 54 mm
Width (W): 9.78 in / 248 mm
Depth (D): 6.96 in / 177 mm
JL Audio
JL AUDIO 5-Channel Class D System Amplifier, 70 W X 4 @ 4 Ω +...
$1,169.00
Crafted as an all-in-one, total system solution, the RD900/5 is engineered to power a complete audio system consisting of a subwoofer + four satellite system with 900 watts of high-performance sound.
Equipped with our exclusive NexD™ switching technology, this complete power package efficiently generates a potent 70 watts of crystal-clear audio into 4 ohms, plus a robust 500 watts for a subwoofer system, all from a single compact chassis. Each pair of main channels is also fully bridgeable, stoutly producing 200 watts of full-range audio bliss (into 4 ohms), creating an ultra-powerful 3-channel amplifier.
Conveniently located on top of the RD900/5, you’ll find a complement of studio-grade signal processing features, all hidden beneath a removable protective cover. Each pair of main channels is equipped with a 12 dB / octave high-pass filter, with a dedicated low-pass filter for its subwoofer channel. All three crossovers offer continuously variable frequency selection from 50-500 Hz, for precise filtering.
Dual-range, differential-balanced inputs are also onboard, capable of accepting most input voltage levels, plus automatic turn-on capability (via signal sensing or DC-offset sensing) for maximum versatility.
LED clipping indicators are also standard equipment for each channel section. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed.
The RD900/5 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition.
With the addition of RBC-1 remote level control (sold separately), you can conveniently control the subwoofer’s output remotely from the driver’s seat.
GENERAL SPECIFICATIONS:
Frequency Response (Main Channels): 12 Hz – 22 kHz (+0, -1dB)
Frequency Response (Subwoofer Channel): 10 Hz – 500 Hz (+0, -1dB)
S/N Ratio, referred to highest rated power (Main Channels): >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W: >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Damping Factor @ 4 Ω: >150 / 50 Hz
Damping Factor @ 2 Ω: >75 / 50 Hz
THD+N @ Rated Power (Main Channels): <1% @ 2 Ω per Ch.
THD+N @ Rated Power (Subwoofer Channels): <1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs: Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge: 4 AWG wire
Fuse Rating: 80 A (AFS, AGU or MaxiFuse™)
JL Audio
JL AUDIO 4-Channel Class D Full Range Amplifier, 100 W X 4 @ 2 Ω...
$639.00
Utilizing our exclusive NexD™ high-speed switching technologies, the ultra-compact RD400/4 amplifier is engineered to deliver loads of audio output power, with incredible efficiency and low distortion.
Don’t let its modern styling and small size fool you though, this little powerhouse churns out 100 watts of crystal-clear audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms.
For your convenience, the RD400/4’s controls can be found on top of the amplifier, beneath a protective cover, with all connections located along one side of its chassis. Studio-grade signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting most input voltage levels.
Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment, along with all-new input type switches for bridging of stereo output channels without needing to use Y-adaptors.
Onboard LED-clipping indicators are also included with your RD400/4. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed.
You’ll also find a set of preamp outputs on-hand, so you can pass signals to another amplifier, almost effortlessly.
The RD400/4 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition.
GENERAL SPECIFICATIONS:
Frequency Response 12 Hz – 22 kHz (+0, -1dB)
S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth)
S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth)
Damping Factor @ 4 Ω >150 / 50 Hz
Damping Factor @ 2 Ω >75 / 50 Hz
THD+N @ Rated Power <1% @ 2 Ω per Ch.
Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High)
Min.Copper Power / Ground Wire Gauge: 4 AWG wire
Fuse Rating: 40 A (AFS, AGU or MaxiFuse™)
JL Audio
JL AUDIO Digital Remote Control For Jlid™ Compatible Products - DRC-205
$229.00
The DRC-205 is a panel-mount, wired digital remote controller designed to connect to the JLid™ port of compatible JL Audio electronics. The specific audio functionality of the DRC-205 controller will be determined by the device it is connected to.
COMPATIBLE WITH:
FiX™ OEM Integration DSP: All models
TwK™ System Tuning DSP: All models
VXi-Series Amplifiers: All models
FUNCTIONS:
Dual-concentric rotary controls with stops
Push-button mode selector
Status indicator (RGB LED)
COMMON USES INCLUDE:
Master Volume
Subwoofer Volume
Preset or Mode Selection
JL Audio
JL AUDIO Digital Remote Control To Suit All Vxi And Fix Models - DRC-100
$149.00
The DRC-100 is a panel-mount, wired digital remote controller designed to connect to the JLid™ port of compatible JL Audio electronics. The specific audio functionality of the DRC-100 controller will be determined by the device it is connected to.
COMPATIBLE WITH:
FiX™ OEM Integration DSP: All models
VXi-Series Amplifiers: All models
FUNCTIONS:
Rotary knob with stops
Push-button mode selector
Status indicator (RGB LED)
COMMON USES INCLUDE:
Master Volume
Subwoofer Volume
Preset or Mode Selection
JL Audio
JL AUDIO Bluetooth® Communicator To Suit Vxi Amplifiers - VXi-BTC
$269.00
FEATURES:
JLid™ Bluetooth® Communicator for VXi Amplifiers
Tune your VXi amplifier via a Bluetooth device
Not for Streaming or Hands Free
JL Audio
JL AUDIO Optical Audio Network Hub To Suit Vxi Amplifiers - VXi-HUB
$319.00
The VXi amplifier ecosystem is designed to be very flexible, offering users almost limitless combinations of amplifiers and channel architectures, along with the amazing power of its integrated DSP technology.
VXi-HUB is an accessory designed to simplify the control of a networked amplifier system, while greatly easing the setup process, by allowing all amplifiers to appear in a single TüN™ software session. VXi-HUB performs two distinct functions as part of a system employing two or more VXi amplifiers: data networking and digital audio distribution.
Data networking is the primary function of the VXi-HUB, permitting a network of VXi amplifiers to respond to synchronized commands from a single DRC controller (DRC-100, DRC-200 or DRC-205, all sold separately). These commands can include Master Volume, Subwoofer Level, Fader, Zone Level and Preset Selection.
The VXi-HUB also enables the networked VXi amplifiers to be tuned from within a single TüN™ software session, allowing the user to quickly switch between amplifiers during the tuning process, without disconnecting and connecting multiple cables.
For data networking purposes, the VXi-HUB is equipped with one Master and five Slave JLid-COMM connections, permitting the networking of up to six VXi amplifiers using standard CAT5e cables (one master amplifier and five slave amplifiers).
For more complex systems, two VXI-HUBs can be daisy-chained to create a network of up to ten VXi amplifiers (one master amplifier and nine slave amplifiers). VXi-HUB also includes a dedicated JLid-COMM accessory port to allow the connection of the optional VXi-BTC Bluetooth® Communicator (sold separately).
This accessory enables convenient wireless setup and tuning of the entire amplifier network using a compatible iOS® or Android® device with TüN™ Mobile or TüN™ Express apps.
The secondary function of the VXi-HUB is to distribute synchronous optical digital audio signals to the networked amplifiers, avoiding the delays associated with handing digital signals off through a chain of amplifiers. The optical digital audio output of a source unit connects directly to the VXi-HUB’s Optical Audio Input, which then distributes synchronous digital audio to the amplifiers from its five Optical Outputs. VXi-HUB handles S/PDIF signals up to 24 bits/192 kHz.
For ease of connection, the VXi-HUB is powered via the JLid™ connection to VXI amplifiers and requires no separate power or turn-on wiring.
FEATURES:
JLid-COMM Connections: 1 Master Input / 5 Slave Outputs / 1 Accessory Port
Optical Audio (S/PDIF) Connections: 1 Input / 5 Synchronous Outputs
3-way Configuration Switch: Standalone / Primary / Secondary
Amp Identifier Status LEDs
Powered via JLid™ connection to VXi amplifiers
JL Audio
JL AUDIO Mono Block Class D Sub Amplifier With Integrated Dsp - VX1000/1i
$2,479.00
Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
The VX1000/1i monoblock subwoofer amplifier outputs up to 600 watts into 4 ohms, or a jaw-dropping 1000 watts into 2 ohms.
A specialized, low-frequency version of our NexD2™ amplifier technology delivers rock-solid bass performance and fidelity, with outstanding efficiency. Compact dimensions with all connections placed on one side, via mating plugs, greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
INCLUSIONS:
Power Connector (for 2 AWG wire)
Analog Input/Pre-Out Harness
Subwoofer Output Connector
6 ft A/B USB Cable
JL Audio
JL AUDIO 4-Channel Class D Full Range Amplifier With Integrated Dsp - VX400/4i
$2,129.00
Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
With our second-generation NexD2™ technology, the VX400/4i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up to 200 W x 2.
The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency.
The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
INCLUSIONS:
Power Connector (for 4 AWG wire)
Analog Input/Pre-Out Harness
Speaker Output Harness
6 ft A/B USB Cable
JL Audio
JL AUDIO 6-Channel Class D Full Range Amplifier With Integrated Dsp - VX600/6i
$2,659.00
Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
With our second-generation NexD2™ technology, the VX600/6i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up a rock-solid 200 W x 3.
The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency.
The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
INCLUSIONS:
Power Connector (for 4 AWG wire)
Analog Input/Pre-Out Harness
Speaker Output Harness
6 ft A/B USB Cable
JL Audio
JL AUDIO 8-Channel Class D Full Range Amplifier With Integrated Dsp - VX800/8i
$3,189.00
NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
With our second-generation NexD2™ technology, the VX800/8i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms.
It can also be bridged into 4 ohms to deliver a powerful 200 W x 4. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency.
The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
INCLUSIONS:
Power Connector (for 2 AWG wire)
Analog Input/Pre-Out Harness
Speaker Output Harnesses (2)
6 ft A/B USB Cable
JL Audio
JL AUDIO 5-Channel Class D System Amplifier With Integrated Dsp - VX1000/5i
$2,839.00
Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor.
Employing our second-generation NexD2™ amplifier technology, the VX1000/5i efficiently powers a complete audio system. It can drive four main speakers with 75 W x 4 @ 4 ohms while also powering a subwoofer with up to 600W @ 2 ohms.
Bridging the main channels converts it into a very powerful, 3-channel system amplifier with up to 200W x 2 @ 4 ohms on the main channels and 600W @ 2 ohms on the subwoofer channel.
The NexD2™ full-range technology in the main channels of this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency.
The subwoofer channel features an optimized low-frequency variant of the NexD2™ technology. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces.
Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed.
INCLUSIONS:
Power Connector (for 2 AWG wire)
Analog Input/Pre-Out Harness
Speaker Output Harness
Subwoofer Output Connector
6 ft A/B USB Cable
JL Audio
JL AUDIO Enclosed Subwoofer System - CS112TG-TW3
$1,419.00
In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top.
This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω
JL Audio
JL AUDIO Enclosed Subwoofer System - CS110TG-TW3
$1,239.00
In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top.
This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω
JL Audio
JL AUDIO Enclosed Subwoofer System - CP108LG-W3v3
$799.00
This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design.
Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port.
This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal.
Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on the front baffle. A steel mesh grille is included to protect the subwoofer driver.
Construction: CNC-Cut High-Grade MDF
Recommended amplifier power: 100 - 250WNominal Impedance: 4 Ω
JL Audio
JL AUDIO 5-Channel Class D System Amplifier - HD900/5
$2,659.00
While extremely compact, this amazing amplifier will comfortably drive a complete high-performance car audio system: that is, four satellite speaker systems and a subwoofer system... with a very serious 900 watts of power!
Using our Single Cycle Control switching design and R.I.P.S. technology, the HD900/5 delivers 100 W x 4 to its four main channels, plus a very meaty 500 W to its subwoofer channel. Thanks to R.I.P.S., high power can be delivered over a wide range of load impedances, while the tight power supply regulation keeps distortion down, maximizing sound quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price.
This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.
Main Channels @ 4 Ω
100 W RMS x 4
Main Channels @ 3 Ω
75 W RMS x 4
Main Channels @ 2 Ω
75 W RMS x 4
Main Channels @ 1.5 Ω
75 W RMS x 4
Main Channels - Bridged @ 8 Ω
200 W RMS x 2
Main Channels - Bridged @ 4 Ω
150 W RMS x 2
Subwoofer Channel @ 4 Ω
500 W RMS x 1
Subwoofer Channel @ 3 Ω
500 W RMS x 1
Subwoofer Channel @ 2 Ω
500 W RMS x 1
Subwoofer Channel @ 1.5 Ω
500 W RMS x 1
JL Audio
JL AUDIO Monoblock Class D Wide-Range Amplifier - HD1200/1
$2,659.00
JL Audios most powerful HD amplifier employs our advanced Single-Cycle Control switching design and R.I.P.S. technology to deliver 1200 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price.
While targeted primarily to subwoofer applications, the HD1200/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems.
This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.
@ 4 Ω
1200 W RMS x 1
@ 3 Ω
1200 W RMS x 1
@ 2 Ω
1200 W RMS x 1
@ 1.5 Ω
1200 W RMS x 1
JL Audio
JL AUDIO Monoblock Class D Wide-Range Amplifier - HD750/1
$1,769.00
This ultra-compact monoblock amplifier employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 750 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price.
While targeted primarily to subwoofer applications, the HD750/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems.
This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.
@ 4 Ω
750 W RMS x 1
@ 3 Ω
750 W RMS x 1
@ 2 Ω
750 W RMS x 1
@ 1.5 Ω
750 W RMS x 1
JL Audio
JL AUDIO 4-Channel Class D Full-Range Amplifier - HD600/4
$1,949.00
This compact multi-channel powerhouse employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 150 W x 4 or 300 W x 2. Tight power supply regulation keeps distortion down and maximizes sound quality.
When using the HD750/1 or HD1200/1 to drive a subwoofer system, the HD600/4 is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price.
It can also be deployed on its own as a very capable 3-channel system amplifier with 150 W x 2 to the satellites and 300 W x 1 to a subwoofer system.
This amplifier features a brushed aluminum finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.
JL Audio
JL AUDIO Remote Level Control For Select Amplifiers - HD-RLC
$99.00
The HD-RLC remotely controls the Bass Level of the following JL Audio amplifiers:
HD-Series: All modelsXD-Series: All modelsMHD-Series: All modelsM-Series: All models
When the HD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle.
The HD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable.
JL Audio
JL AUDIO 2-Way Convertible Component / Coaxial System - C3-600
$889.00
There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application.
The new C3-600 expands the C3 lineup with a direct-fit product for many Japanese vehicles that will not accept a full-size 6.5-inch speaker.
The C3-600 system features 6-inch (150 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems.
The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures.
C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations!
Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Powerful
Sold as a pair.
Continuous Power Handling (RMS)
75 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
25 - 150 W / Ch.
System Efficiency
89.5 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
50 Hz - 25 KHz ± 3 dB
JL Audio
JL AUDIO 2-Way Convertible Component / Coaxial System - C3-570
$889.00
There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application.
Many people mistakenly believe that an oval speaker cannot perform as well as around one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems.
The C3-570 system features 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-moulded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures.
C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations!
Woofer grilles are not available for this product.
Sonic character: Clean and Powerful
Sold as a pair.
Continuous Power Handling (RMS)
75 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
25 - 150 W / Ch.
System Efficiency
90.0 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
48 Hz - 25 KHz ± 3 dB
JL Audio
JL AUDIO 2-Way Convertible Component / Coaxial System - C3-525
$889.00
There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application.
The C3-525 system features 5.25-inch (130 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-moulded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures.
C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations!
Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Powerful
Sold as a pair.
Continuous Power Handling (RMS)
75 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
25 - 150 W / Ch.
System Efficiency
90.0 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
48 Hz - 25 KHz ± 3 dB
JL Audio
JL AUDIO 2-Way Component System - C2-600
$529.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer deigns.
The C2-600 system features 6-inch (150 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems.
The 6-inch (150 mm) format is a direct fit in many Japanese vehicles where a full-size 6.5-inch speaker (165 mm) will not fit without modification. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6-inch (150 mm) speaker.
The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs.
C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector.
Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
Continuous Power Handling (RMS)
60 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
15 - 100 W / Ch.
System Efficiency
90.5 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
59 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO 2-Way Component System - C2-525
$529.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer designs.
The C2-525 system features 5.25-inch (130 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs.
C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector.
Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
JL Audio
JL AUDIO Coaxial 3-Way Speaker System - C2-690tx
$499.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
The C2-690tx system features 6 x 9-inch (150 x 230 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The 6 x 9-inch (150 x 230 mm) format is a direct fit in many vehicles.
The Mid-Range driver is ferrofluid-cooled, with a 2-inch Mylar® cone diaphragm to smoothly bridge the gap between the woofer and the dome tweeter.
Tweeters are mounted next to the mid-range driver and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
Continuous Power Handling (RMS)
70 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
15 - 125 W / Ch.
System Efficiency
93 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
53 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO Coaxial Speaker System - C2-650x
$439.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
The C2-650x system features 6.5-inch (165 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker.
Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Continuous Power Handling (RMS)
60 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
15 - 100 W / Ch.
System Efficiency
91 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
59 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO Coaxial Speaker System - C2-600x
$439.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
The C2-600x system features 6-inch (150 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
The 6-inch (150 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker.
Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
JL Audio
JL AUDIO Coaxial Speaker System - C2-570x
$439.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
Many people mistakenly believe that an oval speaker cannot perform as well as around one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems.
The C2-570x system features 5 x 7 / 6 x 8-inch (125 x 180 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Grilles are not available for this speaker system.
Sonic character: Clean and Dynamic
Sold as a pair.
Continuous Power Handling (RMS)
60 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
15 - 100 W / Ch.
System Efficiency
90.5 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
53 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO Coaxial Speaker System - C2-525x
$439.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
The C2-525x system features 5.25-inch (130 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
Continuous Power Handling (RMS)
60 W
Peak Music Power
225 W
Recommended Amplifier Power (RMS)
15 - 100 W / Ch.
System Efficiency
89.0 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
63 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO Coaxial Speaker System - C2-400x
$319.00
The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs.
The C2-400x system features 4-inch (100 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems.
Breakaway mounting tabs on the woofer frame allow the C2-400x to be installed in four-hole or two-hole configurations. Injection-moulded adaptor plates are also included to allow mounting of the C2-400x speakers into a 4 x 6 (100 x 150 mm) speaker location.
Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles.
Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo.
Sonic character: Clean and Dynamic
Sold as a pair.
Continuous Power Handling (RMS)
35 W
Peak Music Power
105 W
Recommended Amplifier Power (RMS)
10 - 50 W / Ch.
System Efficiency
84.5 dB @ 1 W / 1 m
System Nominal Impedance
4 Ω
System Frequency Response
71 Hz - 22 KHz ± 3 dB
JL Audio
JL AUDIO 10Th Anniversary Edition - W7 12-Inch Subwoofer Driver - 12W7AE-3
$2,479.00
The 12W7AE brings serious performance to the table by combining the breakthrough of the long-excursion W7 design with a large 12-inch bore. It has been called "addictive," "seductive" and "the new subwoofer reference", by some of the world's toughest reviewers, and has earned these accolades by delivering nearly limitless dynamics, exceptional balance and world-class sound quality.
This potent driver is best used with amplifier power in the 400W - 1000W range and is optimized to operate in a 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure.
W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but are they distinguished by the following cosmetic differences:
Satin-Black Powdercoated Baskets
Bright Anodized Surround Clamp Ring
Anniversary Edition Cone Badge
Anniversary Edition Terminal Label
Continuous Power Handling (RMS)
1000 W
Recommended Amplifier Power (RMS)
400 - 1000 W
Nominal Impedance (Znom)
3 Ω
JL Audio
JL AUDIO W7 10-Inch Subwoofer Driver - 10W7AE-3
$1,949.00
If you are seeking reference-grade sub-bass from a 10-inch driver, your search ends here. Total Car Audio in the UK called it like this when they reviewed the 10W7: "This gives an all-around performance of such high quality on every level, that bettering it will be very hard to achieve." Not only does the 10W7 deliver amazing excursion capability for its size, but it also maintains complete composure under power and is able to track complex bass material with uncanny accuracy and power.
The 10W7AE is best used with amplifier power in the 300W - 750W range and is optimized to operate in a 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.5 cu. ft. (42.5 l) ported enclosure.
W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences:
Satin-Black Powdercoated Baskets
Bright Anodized Surround Clamp Ring
Anniversary Edition Cone Badge
Anniversary Edition Terminal Label
Continuous Power Handling (RMS)
750 W
Recommended Amplifier Power (RMS)
300 - 750 W
Nominal Impedance (Znom)
3 Ω
JL Audio
JL AUDIO W7 8-Inch Subwoofer Driver - 8W7AE-3
$1,419.00
This subwoofer driver has been called the "best damn 8-inch subwoofer ever made" for its remarkable performance capabilities and design attributes. An impressive linear excursion envelope that exceeds 0.75 in. (19 mm) one-way allows it to deliver impact well beyond the range of other 8-inch subwoofer drivers.
The 8W7AE is best used with amplifier power in the 200W - 500W range and is optimized to operate in a 0.875 cu. ft. (24.8 l) sealed enclosure, or a 1.0 cu. ft. (28.3 l) ported enclosure.
Continuous Power Handling (RMS)
500 W
Recommended Amplifier Power (RMS)
200 - 500 W
Nominal Impedance (Znom)
3 Ω
JL Audio
JL AUDIO Tw5V2 13.5-Inch Subwoofer Driver - 13TW5v2-4
$1,599.00
JL Audio patented thin-line woofer technology compresses the architecture of the 13TW5v2 using a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the speaker than with conventional designs, while allowing excellent linear excursion capability and mechanical stability.
To unleash even more performance from this technology, the v2 improves upon the original 13TW5 with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is also available in single 2 ohm and si4-ohm4 ohm voice coil versions to fit a wide range of applications.
In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 10-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer.
The 13TW5v2 is best used with amplifier power in the 250W - 600W range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure.
JL Audio
JL AUDIO Tw3 12-Inch Subwoofer Driver - 12TW3-D4
$979.00
Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s.
To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs.
TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers.
Continuous Power Handling (RMS)
400 W
Recommended Amplifier Power (RMS)
200 - 400 W
Nominal Impedance (Znom)
Dual 4 Ω
JL Audio
JL AUDIO Tw3 10-Inch Subwoofer Driver - 10TW3-D4
$889.00
Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s.
To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs.
TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers.
Deep, powerful and accurate JL Audio bass is now possible in more applications than ever.
Continuous Power Handling (RMS)
400 W
Recommended Amplifier Power (RMS)
200 - 400 W
Nominal Impedance (Znom)
Dual 4 Ω
Wolverine
WOLVERINE Land Cruiser 300 Series Gr Flare Kit With Mudflaps (Full-Set) -WF300GRMF
$1,299.00
$1,799.00
Transform your Landcruiser 300 Series GR with our premium aftermarket flares, designed to provide additional clearance for larger tires while enhancing the rugged appearance of your vehicle. Each set includes four external flares and mudflaps for complete wheel arch coverage and compliance.
Key Features
35mm Width Extension – Perfect balance of protection and aggressive styling
Innovative 2-Piece Front Design – Compatible with Landcruiser 300 Series GR model, with or without bull bar
Contoured Seal System – Prevents mud/sand ingress and protects your vehicle's paintwork
Premium Materials – High-quality UV-coated ABS plastic for superior durability
Flare Kit – Includes four flares and mudflaps for full vehicle coverage
DIY Installation – Direct replacement design for straightforward installation
Australian Made – Designed, tested, and manufactured for Australian conditions
Technical Specifications
Compatibility: Toyota Landcruiser 300 Series GR ONLY
Material: Premium ABS Plastic with UV protection
Finish: Matte black, ready to install or paint
Installation: Direct replacement (DIY)
Package Contents: 4 external flares (front pair features 2-piece design), mudflaps, installation hardware, instructions
The Wolverine Difference
Unlike competitor products that require cutting or modification to fit vehicles with bull bars, our innovative 2-piece front flare design adapts perfectly to your Landcruiser 300 GR, regardless of your front-end setup. The precision-engineered contoured seal creates a cleaner look and protects your vehicle's paintwork from damage while preventing mud and debris from becoming trapped between the flare and the body.
Installation
Our flares are designed for straightforward DIY installation with standard tools. Comprehensive instructions are included, and installation typically takes 1-2 hours for the complete set.
Wolverine
WOLVERINE 4X4 Premium Fender Flares - W4X4-300
$990.00
$1,490.00
Wolverine 4x4 Premium Fender Flares - 300 Series Toyota Landcruiser
100% Australian designed, engineered, and manufactured, these premium fender flares are built tough for your 300 Series Landcruiser. Crafted from high-grade ABS plastic, they feature advanced UV-resistant coating to maintain their sleek appearance season after season. The intelligent design requires no cutting or modification for bullbar installation, making fitment a breeze across all 300 Series models.
Key Features:
100% Australian made, designed, and engineered
Full compatibility with all 300 Series Landcruiser models
Premium ABS plastic construction for durability
UV-resistant coating prevents sun fading
No cutting required for bullbar installation
Easy bolt-on fitment
Transform your 300 Series with the perfect blend of protection and style. Designed and manufactured right here in Australia to complement your vehicle's lines while providing essential coverage for oversized tires and protecting against debris.
nomadiQ
NOMADIQ - The Original Bbq - Nmq-35113 - NMQ-35113-01
$439.00
$499.00
Experience effortless outdoor cooking with the Original nomadiQ BBQ – NMQ-35113, a premium lightweight, dual-zone gas BBQ crafted for travel, camping, and open-air dining. With a sleek foldable design, 60-second setup, and the power to cook for up to 8 people, it combines performance with portability. At just $439, it’s the ideal companion for those who value quality, convenience, and adventure.
What’s in the Box?
Everything you need to get cookin’ - just add gas.
Here’s what’s inside:
The nomadiQ BBQ (foldable, dual-zone, gas-powered)
Gas hose with pressure regulator
2x drip trays
Shoulder carry strap
Quick-start manual
DELIVERY INFORMATION - PLEASE READ
✅ Lock in current $439 pricing by pre-ordering now✅ Guaranteed availability when next shipment arrives✅ First in line for delivery (3-5 days from order)✅ No payment until your BBQ is ready to ship*✅ Full refund available if you change your mind before shipping
All packed in a recyclable box. You’ll be up and cooking in under 60 seconds.
The nomadiQ BBQ comes in a recyclable box complete with gas hose, pressure regulator, drip trays, shoulder strap, and a manual. Only the gas bottle is needed for hours of grilling and fun.
You can take this lightweight gas BBQ with you anywhere. It has two separate temperature zones and is easy to clean after use. As a true outdoorsman, you can lick your fingers with this compact BBQ hit.
TRAVELLERS STATE OF MIND: Ultimate Lightweight and Portable BBQ
We developed the nomadiQ BBQ with the outdoorsmen in mind. Total weight is only 12.5lb. It comes standard with a shoulder strap. The unique folding design makes it sleek and ultra-portable while being a powerhouse of a gas BBQ. We also offer a nomadiQ Pouch for your convenience.
UNLOCK, UNFOLD & CONNECT: The nomadiQ BBQ Folding Design
The nomadiQ BBQ has a one-of-a-kind Folding Design. The only thing you have to do is unlock, unfold, connect to a propane tank, and grill food within a minute. When you're done, you can easily clean, pack, and drive home after a beautiful day with friends or family.
MAXIMUM CONTROL: Dual and Separate Heating System
On both sides of the nomadiQ BBQ you can enjoy a grill plate of 730 cm² (total 1460 cm²). With two separate sides, this BBQ allows you to use only one or both sides, while controlling their temperatures individually using independently controlled burners.
EASY CONNECTION: Propane Gas Bottle
You can use every standard propane fuel tank available at hardware stores, outdoor suppliers, and bigger supermarkets.
✅ Portable & Lightweight✅ Dual-Zone Grilling✅ Order: 3-5 Days Delivery (Due to High Demand)✅ $50 - $100 cheaper than other Aussie retailers
SPECIFICATIONS
Weight: 7.4 kgDimensions: 46 × 50 × 21 cmColour: Charcoal Black, Petrol, Pretty Pink, Terra, Urban GrayGas type: PropaneMaterial: Aluminium, Powder Coating, Stainless steelPower: 9200 btuGrilling surface: 1460 cm² / 226 in²Safety approval: C-ETLCertification standard: ANSI Z21.89:2017 / CSA 1.18:2017Brand: nomadiQ
Why NomadiQ?
Because it just works – anywhere you go. The nomadiQ is the lightest and most compact gas BBQ on the market.
nomadiQ is the BBQ you take to the beach, the bush, or the backyard without a second thought. It’s lightweight, packs down small, and heats up fast. Two separate burners give you proper control – bacon on one side, eggs on the other.
No fuss. No heavy lifting. Just good food, good times, and no compromises.
And for $439, it’s a no-brainer.
Pre-order now to lock in this price and secure your spot in the delivery queue.
NomadiQ BBQ Warranty Summary
Coverage: Defects in material and workmanship under normal, private residential use.
Base & Grilling Shells: 5 years (2 years on paint; fading/discolouration not covered)
Stainless Steel Burner Tubes: 5 years
Aluminium Die-Cast Grates: 5 years
Plastic Components: 5 years (excluding fading/discolouration)
All Other Parts: 2 years
nomadiQ
NOMADIQ Grilling Grate - NMQ-79891
$39.95
This nomadiQ grate is a replacement of your original one. They will fit on any nomadiQ BBQ. Make sure you season it with vegetable oil before every use as it will increase the durability. DON”T use any metal utensils or cleaning brushes on them as they will damage the non-stick coating.
Lightforce
LIGHTFORCE Beast 3 Mode Led Driving Light - BEAST230PK
$989.00
$1,199.00
Conquer the night with the Lightforce Beast 3-Mode LED Driving Lights — built tough for serious off-roading. Switch between spot, flood, and Beast mode for unmatched visibility up to 1km ahead. Aussie-made, IP69K rated, and engineered for premium 4WD performance. Now only $989 a pair.
What’s in the Box?
2 x BEAST LED Driving Light
2 x Lightforce BEAST Clear Filter
2 x Lightforce BEAST Amber Filters
2 x Reversible mounting bracket
2 x 4 pin waterproof adaptor
1 x User instructions
CHANGE BEAM PATTERNS WITH THE PUSH OF A BUTTON
Ensuring you are in command of any situation with confidence, BEAST has a unique 3-mode operation, allowing effortless switching between spot, flood and BEAST mode all from the comfort of your driving seat.
3 MODES IN 1
Spot: 1 LUX @ - 1497M DISTANCE - 60M WIDE
Flood: 1 LUX @ - 778M Distance - 140M Wide
Beast: 1 LUX @ - 1375M Distance - 140M Wide
Tame your terrain with BEAST’s SPOT beam pattern. Ideally suited for those who require a long-distance LED driving light with a more focused beam pattern. The concentrated white light will provide increased visibility when wanting to see as far as you can at night.
AN UNRIVALLED DRIVING EXPERIENCE
Whether you're traversing long terrains or embarking on the next thrilling adventure, BEAST guarantees the ultimate driving experience. Its reliability and precision, make it the ideal companion for those who seek performance without compromise. Elevate your driving journey with BEAST, where every detail is designed to exceed your expectations.
BOLD, RUGGED, EVOLVED
When it comes to BEAST, we leave no room for compromise. Each component, and every detail has been scrutinised and perfected to deliver an unparalleled driving experience. By adhering to our rigorous design principles, BEAST ensures that it not only meets but exceeds expectations, making it an Australian Made driving light that embodies uncompromising quality.
REAR BASH PLATE
Eye catching, military inspired accessory bash plate
HARD COATED LENS
Extremely impact resistant and durable
BLACK REFLECTOR MASK
Provides a class leading look and feel
SLIMLINE FOOTPRINT
Almost half the weight of other driving lights
PREMIUM COATINGS & FINISHING
Chemical, UV and salt resistant, tested to exceed Australian standards
GORE® MEMBRANE
Genuine Gore® waterproof membrane with mechanical seal
ALUMINIUM HOUSING
Durability of the highest degree to withstand the hardest of conditions
TESTED BEYOND THE EXTREME
IP69K INGRESS PROTECTION
DUST, PRESSURISED STEAM, 1.5M DEEP SUBMERSION
RUNS SAFELY IN -40°C TO 70°C HEAT
WORKS IN HEAT SPIKES UP TO 125°C AND WHEN FROZEN SOLID
SURVIVES IK16 RATED IMPACTS
IMPACT ESTIMATE OF 400G ROCK AT 100KPH OR 1KG AT 60KPH
PASSES MIL-STD-810H 514.4 VIBRATION AND SHOCK TEST US MILITARY STANDARD FOR OFFROAD VEHICLES
IEC 60068-2-52 SALT SPRAY AND RUST RESISTANT
SURVIVES 150,000 POWER CYCLES
LASTS 10,000 HOURS OF CONTINUOUS RUNNING
LEDS RATED TO 50,000 HOURS LIFESPAN
ASTM D3359 TOUGH COATING SCRATCH TEST
CHEMICAL RESISTANT MATERIALS TO UN ECE.R149
SURVIVES PETROL, BRAKE FLUID, MEK AND PAINT SOLVENTS
IEC 60068-2-5 SOLAR AND UV RESISTANT LENS
EMI IMMUNITY TO UN ECE.R10
LOW RADIO EMISSIONS TO CISPR25
ROHS COMPLIANT MATERIALS
NON-HAZARDOUS SUBSTANCES
RCM, CE, AND FTC COMPLIANT
AU/NZ, EU AND USA APPROVALS RESPECTIVELY
THE AUSTRALIAN-DESIGNED, ENGINEERED, TESTED AND MANUFACTURED BEAST LED DRIVING LIGHT BY LIGHTFORCE FUSES MILITARY PRACTICALITY AND RUGGEDNESS WITH BOLD AND UNIQUE DESIGN STYLING.
Built to endure and offer versatility in the most extreme driving conditions, it surpasses global test standards for durability and longevity, leading us to consider it the most rigorously tested Australian made driving light on the market, ensuring you are in command of any situation with confidence.
With its unique 3-mode operation, effortlessly switch between spot, flood and a special BEAST mode all from the comfort of your driving seat.
BOASTING:
Improved peripheral vision, assisting a safe drive
Warm white colour reduces glare and eye strain
Consistent and precise beam patterns for driving with confidence on any road type
Slimline footprint and lightweight
Countless mounting opportunities for seamless vehicle integration
A hard coated lens that’s extremely impact resistant and durable
Evolve your driving experience and unleash the wild your way with BEAST by Lightforce.
KEY BENEFITS
Globe Tech: LED
Number of LEDs: 36
Distance: 1 lux at: 1497m
Effective Lumens: 10,275 / 7,826 / 13,269lm
Raw Lumens: 16,496 / 11,025 / 19,965lm
Colour Temperature: 5700K
CRI: 70
Current Draw: 11.2 / 6.5 / 13Amps @ 13.2V
Voltage: 13.2V
Wattage: 149W
Ingress Protection Rating: IP69K
Beam Type: 3 Mode
Diameter: 230mm
Candella: 1,105,100 / 302,740 / 945,300cd
Weight: 2.2kg / 4.9lb
Warranty: 5 Years
nomadiQ
NOMADIQ Drip Tray - NMQ-53491
$36.60
These nomadiQ Drip Tray are a replacement of your original ones. They will fit under any nomadiQ BBQ.
In case you have misplaced or damaged your nomadiQ BBQ Drip Trays this is a replacement pair.
Additional information
Weight
0.2 kg
Dimensions
18 × 7 × 4 cm
Colour
Charcoal Black
Material
Nylon + glassfiber
Capacity
125ml
Brand
nomadiQ
