This improvement solution perfectly adapted to your Peugeot car. This 2-way coaxial kit integrates easily and quickly into the original slots without major modification. Go straight to the next level with powerful, sensitive and faithful acoustics. IC PSA 165 Features Respect of the original Peugeot® connectors Better precision in high frequencies High-density rubber ring for acoustic sealing with the door panel Taking the PEUGEOT kit to another level Acoustic insulation can also be added to improve the sound of these speakers.

This improvement solution perfectly adapted to your Peugeot car. This 2-way coaxial kit integrates easily and quickly into the original slots without major modification. Go straight to the next level with powerful, sensitive and faithful acoustics. IS PSA 165 Features Respect of the original Peugeot® connectors Better precision in high frequencies High-density rubber ring for acoustic sealing with the door panel Taking the PEUGEOT kit to another level Acoustic insulation (such as FOCAL BAM) can also be added to improve the sound of these speakers.

The woofer is the result of a long study on the efficiency/frequency compromise and offers intense but subtle bass reproduction. The aluminum inverted-dome tweeter, hallmark of the brand, provides neutral treble reproduction, which is accurate and reliable up to the highest frequencies. Working on the tweeter formers produced an aesthetic match with the dashboard. Above all, thanks to its orientation and specific binding, the tweeter development greatly improved the original sound image (height, depth and width of soundstage).  IFP207 Technical Specifications Woofer Diameter 61/2″ (165mm) Cone Polyglass Basket ABS Voice coil 1″ (25mm) Magnet 31/3″ (85mm) Sensitivity 92.7dB Re 2.6 Ohms Bandwidth 70 Hz – 25 kHz Max. power 140 W RMS Power 70 W Integrated crossover 6/18 dB/oct (4kHz) Tweeter Aluminium/Magnesium inverted dome TNB Tweeter mounting Moulded for perfect integration in the original location and respect of the dashboard design.

Harness IW-SPK-SIM simulates 4 ohm speaker load as required by various headunits.

Harness IW-SPK-SIM simulates 4 ohm speaker load as required by various headunits.

The compact PSB200 measures less than 51/8" deep (13cm deep, with the grille) and therefore slides easily into a car boot. And its size isn’t the only great feature: it is also easy to use and delivers quality sound performance thanks to its 8" subwoofer that has 250 watts of power. Delivered with brackets, screws and a set of hook-and-loop fastener, PSB200 can be fixed in various locations in your vehicle and it perfectly completes a 2 or 3-way audio system while remaining discreet and delivering precise and dynamic bass. With this passive enclosure, discover the pleasure of all sound nuances during your drive. Features: Easy to install 250W Max Compact Protection grille included MDF structure, rigid enclosure Includes screws, brackets and adhesive strip Specifications: Type: Sealed enclosure Subwoofer: 8" (200mm) Dimensions: (HxDxW) 12" x 4.9" x 19" (303.6 x 124.8 x 489mm) Weight: 15lbs (7kg) Impedance: 4Ω Max. power: 250W Nom. power: 150W Sensitivity (2.83 V/1 m): 83dB Frequency response: 45Hz - 150Hz Accessories: Screws, brackets and adhesive strip

PS 165 V1 Description The Focal PC 165 V1 6.5″ 2-way coaxial speakers feature Partial horn loading of the tweeter and high sensitivity to ensure dynamics and neutrality even off high powered factory stereo systems. Features: Partial Horn Loading High Sensitivity Dynamics & Neutrality Adjustable Tweeter Levels 80W RMS Nominal Power Handling 160W RMS Max. Power Handling Specifications: 2-way coaxial kit Diameter: 61/2" (165mm) Voice-coil diameter: 1" (25mm) Voice-coil height: 01/2" (13mm) Motor: Magnet Aluminium/Magnesium inverted dome tweeter Cone: Flax Integrated crossover: 6dB/Oct Max. power: 140W Nom. power: 70W RMS Sensitivity (2.83V/1m): 91.9dB Frequency response: 60Hz – 28kHz Impedance: 4Ω Accessories: Supplied grilles

The FDS 1.350 is a compact mono amplifier specifically designed for handling a subwoofer channel. It has a power of 210 and 350 Watts RMS under 4 and 2 Ohms respectively. In order to configure the system’s bass according to the car’s installation; it is equipped with an active crossover, bass correction and phase adjustment. Mono D Class amplifier with dual output RCA inputs FOCAL FDS 1.350 KEY FEATURES D Class – Direct Fet ® Technology – Efficient heat dissipation and precision Stable under 2 Ohms Stackable aluminium chassis with high heat dissipation Low noise operational amplifier New Japan Radio® NJM4580 Low ESR capacitors – 105°C (220°F) Pseudo-balanced inputs Cable accessories included – easy to install

4-CHANNEL AMPLIFIER – 4X120 W RMS The FPX 4.800 is a very compact 4-channel amplifier with a power of 4×120 Watts RMS at 4 Ohms. Offering a 4-/3-/2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, the FPX 4.800 is the most versatile model in this range. Thanks to its very high power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair of output lines. The high power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line. FOCAL FPX 4.800 KEY FEATURES 4-/3-/2-channel Class D amplifier 2-/4-channel input modes Stable at 2 Ohms Active crossover for each pair of channels EXTREMELY VERSATILE Thanks to its 4×120 Watts RMS at 4 Ohms and its compact chassis barely bigger than half a page of A4 paper, the FPX 4.800 is an ideal solution for a wide range of uses. In bridged mode, it delivers 2×370 Watts RMS at 4 Ohms, enabling it to power a significant subwoofer channel with channels 3 and 4. It is also stable at 2 Ohms (4×185 Watts RMS) so it can also be used for powering different types of speaker drivers. In order to perfectly power the speaker drivers, each pair of channels is equipped with an adjustable active crossover from 50 to 500 Hz: high-pass, low-pass or wideband. Channels 3 & 4 are equipped with bass correction. The 2-/4-channel input modes ensure compatibility with mid-range head units only equipped with a pair of output lines. WHAT MAKES THE DIFFERENCE A compact and versatile amplifier Optimised heat dissipation Extremely versatile Remarkable power/performance/price ratio

4-CHANNEL AMPLIFIER – 4 X 70 W RMS The FPX 4.400 SQ is a very compact 4-channel amplifier with a power of 4 x 70 Watts RMS at 4 Ohms. Offering a 4 or 2-channel mode, stable at 2 Ohms and equipped with an active crossover for each pair of channels, makes the FPX 4.400 SQ very versatile and suitable to a range of system designs. Thanks to its high power, this is the ideal amplifier for powering front and rear speaker drivers, or for hi-fi installations with a 2-way kit in the front and a subwoofer. The 2-/4-channel input modes ensure compatibility with head units only equipped with a pair of output lines. The high power and musicality of this amplifier will ensure you get the best out of your high-end speaker drivers from our Performance line. FOCAL FPX 4.400 SQ KEY FEATURES 4-/2-channel Class A/B amplifier 70 Watts RMS x 4 at 4 ohms (100 Watts RMS x 4 @ 2 ohms) Stable at 2 Ohms CEA-2006 Compliant Class A/B Design for Best Available Sound Reproduction Active crossover for each pair of channels WHAT MAKES THE DIFFERENCE A compact and versatile amplifier Optimised heat dissipation Extremely versatile Remarkable power/performance/price ratio

The FPX 1.1000 is a very compact mono amplifier with a power of 420 Watts RMS at 4 Ohms. Specially designed for powering a subwoofer, this amplifier combines very high power and some great features. POWERFUL AND VERSATILE 420W MONO AMPLIFIER The FPX 1.1000 is a very compact mono amplifier with a power of 420 Watts RMS at 4 Ohms. Specially designed for powering a subwoofer, this amplifier combines very high power and some great features. Stable at 2 Ohms and 1 Ohm, equipped with a complete range of settings for adjusting low-frequency sensitivity, a remote control and output lines, this amplifier is capable of bluffing performances. Whether it’s for powering an audiophile bass system or a powerful subwoofer, the FPX 1.1000 will meet all your needs for your bass channel. FOCAL FPX 1.1000 KEY FEATURES Mono Class D amplifier Complete range of settings (active crossover, subsonic filter, bass boost, phase control) Stable under 2 Ohms and 1 Ohm Output lines COLOSSAL POWER FOR SUCH A COMPACT CHASSIS Very compact and easy to integrate, the FPX 1.1000 amplifier has been specifically developed for powering all types of the subwoofer. It is stable at 4 Ohms, 2 Ohms and 1 Ohm, delivering a respective power of 420, 700 and 1000 Watts RMS. Whether it’s for an audiophile bass system or a powerful subwoofer, the FPX 1.1000 will meet all your needs. It features all the settings you’d expect to find in such an efficient bass amplification system: an adjustable low-pass active crossover with a slope of 24 dB, subsonic filter with a slope of 24 dB, bass boost and phase control. The FPX 1.1000 comes supplied with remote control for controlling the bass from the dashboard, and a pair of output lines for hooking up a second amp. This is especially useful for setting up a bass channel with two subwoofers and two amplifiers. WHAT MAKES THE DIFFERENCE A powerful and ultra-compact amplifier Perfect for audiophile installations or powerful subwoofer systems Optimised heat dissipation Extremely versatile Remarkable power/performance/price ratio

Extremely Versatile With the FPX 5.1200, installation of this hi-fi system is much easier as there's only one amplifier and one power supply to fit into the vehicle. In order to control this 5-channel installation (with front and rear speaker drivers, and a subwoofer), the FPX 5.1200 features a wide range of settings. The input selector (2/4/6 channels) duplicates channels, meaning there will always be 5 output channels, even if the head unit only has one or two stereo outputs. For the main speaker drivers, each pair of channels has an adjustable active crossover. To perfectly tune the subwoofer to the rest of the installation, the bass channel has a low-pass active crossover, a bass equaliser, phase adjustment and a subsonic filter (particularly useful for cutting off frequencies which are too low for a small subwoofer). The remote control enables you to adjust the bass level from the driving seat depending on the type of music you’re listening to. Stable at 4 and 2 Ohms, this new FPX amplifier will drive most speaker drivers on the market with just the right amount of power: 4 x 75 Watts + 1 x 420 Watts RMS at 4 Ohms (CEA standard). With the launch of the FPX 5.1200, Focal now offers a full range of amplifiers, from the Impulse ‘Plug & Play’ amplifier to the audiophile FPX amplifier. Through our compact FD amplifiers, Focal is able to meet the expectations of all those looking for a car audio amplifier. With its high power, great musicality and compact design, as well as being ideal for powering a complete installation with Flax or K2 Power speaker drivers, the FPX 5.1200 will meet all the expectations of hi-fi car audio enthusiasts. Extensive research for unprecedented power in a compact enclosure Delivering very high power from such a compact enclosure is a true challenge. The more heat an amplifier produces, the higher the risk of distortion affecting the system’s musicality. By using Class D technology, Focal has reduced the need for heat dissipation for its FPX range. However, in order to achieve high efficiency and to optimise reliability, FPX amplifiers required extensive research: the selection of the best components, a thick aluminium chassis, very precise positioning of the components, monitoring heat dissipation with a thermal camera and accelerated aging tests in draconian conditions. Focal’s goal is to offer electronics equipment which is very compact and powerful, but without sacrificing musicality. The dimensions of the 5-channel FPX 5.1200 amplifier (337 x 175 x 57mm / 13.25"x 6.8" x 2.25") are nearly the same as the FPX 4.400 SQ. The FPX 5.1200 has a maximum power of 4 x 120 Watts + 1 x 720 Watts at 2 Ohms!

Give your head unit a breath of fresh air Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. TECHNOLOGY PLATFORM FROM FD AMPLIFIERS The technology used for Impulse 4.320 was inspired by the Performance range’s FD amplifiers. With an efficiency of more than 90%, Class D amplification has numerous advantages: less heat, low power consumption, low distortion at high volumes, compact…With the Impulse 4.320 amplifier, an unbeatable size/power ratio has been achieved. It delivers 4 x 55 or 2 x 160 Watts RMS at 4 Ohms. Thanks to the adequate power and the fast attack for realistic and more aerated sound, it will completely transform the sound of your front and rear speaker drivers. VERY EASY TO INSTALL AND PERFECT INTEGRATION Impulse 4.320 – Cables Measuring only 67/8 x 17/8 x 25/8″ (17.65 x 4.6 x 6.7 cm) Impulse 4.320 can easily be concealed within the dashboard or the centre console. Equipped with high-level (automatic detection feature) and low-level inputs, it is compatible with all head units. Supplied with all fastenings, an adaptor for the head unit’s speaker driver outputs, RCA adaptors for aftermarket head units and power connector, this amp was specially designed to be easy to install. No direct hook up to the vehicle’s battery is required. An optional ISO connector is available for “Plug&Play” connectivity via the head unit’s harness. Note: On certain cars, a harness adapter may be necessary. EXTREMELY VERSATILE To ensure compatibility with different head units, this amplifier features a 2-channel or 4-channel input selector switch. Most of all, Impulse 4.320 has been designed to power front and rear speaker drivers. However, it can also be used in a 3-channel or 2-channel mode in order to meet all needs for improving small installations and it can also be used for powering the front speaker drivers and a small subwoofer. Each pair of channels features an active crossover to adapt the sonic response according to the speaker drivers used. The front channels can be used for wideband speaker drivers or the high-pass filter can be used for frequencies above 75 Hz when only small speaker drivers are used. By avoiding having small speaker drivers reproduce very low frequencies, the sound will have more clarity. The rear channels are equipped with an active crossover (wideband, high-pass or low-pass) and with progressive phase adjustment for powering a small subwoofer or wideband speaker drivers of different sizes.

10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level. Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label General Specifications Continuous Power Handling (RMS) 1500 W Recommended Amplifier Power (RMS) 500 - 1500 W Nominal Impedance (Znom) Dual 1.5 Ω Physical Specifications Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14 in / 356 mm Mounting Hole Diameter (B) 11.9 in / 302 mm Bolt Hole Circle Diameter (C) 12.7 in / 323 mm Motor Outer Diameter (D) 8.38 in / 213 mm Mounting Depth (E) 10.5 in / 267 mm Driver Displacement 0.21 cu ft / 5.9 L Net Weight 52 lb / 23.6 kg Parameters Free Air Resonance (Fs) 23.5 Hz Electrical “Q” (Qes) 0.476 Mechanical “Q” (Qms) 7.517 Total Speaker “Q” (Qts) 0.448 Equivalent Compliance (Vas) 3.68 cu ft / 104.3 L One-Way Linear Excursion (Xmax)* 1.25 in / 32 mm Reference Efficiency (no) 0.27% Efficiency (1 W / 1 m)** 86.3 dB SPL Effective Piston Area (Sd) 107.35 sq in / 0.0693 sq m DC Resistance (Re)*** 2.41 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 1.875 cu ft / 53.1 L External Width (W) 16 in / 407 mm External Height (H) 16 in / 407 mm External Depth (D) 18.875 in / 479 mm F3 37.4 Hz Fc 40.5 Hz Qtc 0.77 Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 2.375 cu ft / 67.3 L External Width (W) 25.875 in / 657 mm External Height (H) 16 in / 406 mm External Depth (D) 17.25 in / 438 mm Internal Slot Port Width (SW) 2.25 in / 57 mm Internal Slot Port Height (SH) 14.5 in / 368 mm Internal Slot Port Length (SL) 26.25 in / 667 mm Port Extension Length (EL) 7.875 in / 200 mm Tuning Frequency (Fb) 34.6 Hz F3 30.3 Hz Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)   If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 12W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.02 in / 280 mm Bolt Hole Circle Diameter (C) 11.86 in / 301 mm Motor Outer Diameter (D) 7.0 in / 178 mm Mounting Depth (E) 7.52 in / 191 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.105 cu ft / 2.97 L Net Weight 25.6 lb / 11.6 kg Parameters Free Air Resonance (Fs) 26.919 Hz Electrical “Q” (Qes) 0.487 Mechanical “Q” (Qms) 9.365 Total Speaker “Q” (Qts) 0.463 Equivalent Compliance (Vas) 1.920 cu ft / 54.37 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 85.4 dB SPL Effective Piston Area (Sd) 75.338 sq in / 0.0486 sq m DC Resistance (Re)*** 6.493 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.0 cu ft / 28.3 L External Width (W) 15 in / 381 mm External Height (H) 15 in / 381 mm External Depth (D) 12 in / 305 mm F3 41.62 Hz Fc 45.99 Hz Qtc 0.7912 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.3 cu ft / 36.8 L External Width (W) 27 in / 686 mm External Height (H) 14 in / 356 mm External Depth (D) 12.5 in / 318 mm Internal Slot Port Width (SW) 1.75 in / 44 mm Internal Slot Port Height (SH) 12.5 in / 318 mm Internal Slot Port Length (SL) 37.125 in / 943 mm Port Extension Length (EL) 21.250 in / 540 mm Tuning Frequency (Fb) 33 Hz F3 31 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 2 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-2 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.55 Hz Electrical “Q” (Qes) 0.554 Mechanical “Q” (Qms) 8.731 Total Speaker “Q” (Qts) 0.521 Equivalent Compliance (Vas) 2.544 cu ft / 72.04 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.23% Efficiency (1 W / 1 m)** 85.9 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 2.210 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 38.99 Hz Fc 48.39 Hz Qtc 0.9496 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 4 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.21 Hz Electrical “Q” (Qes) 0.535 Mechanical “Q” (Qms) 8.2 Total Speaker “Q” (Qts) 0.502 Equivalent Compliance (Vas) 2.706 cu ft / 76.63 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.25% Efficiency (1 W / 1 m)** 86.1 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 3.915 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 39.63 Hz Fc 48.75 Hz Qtc 0.9338 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31.41 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 10-inch Subwoofer (300 W, 4 Ω)   The 10W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (4.6 in. / 117 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 10-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 10W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.92 in / 125 mm Mounting Depth (E) 4.6 in / 117 mm Driver Displacement 0.037 cu ft / 1.05 L Net Weight 9.9 lb / 4.5 kg Parameters Free Air Resonance (Fs) 26.15 Hz Electrical “Q” (Qes) 0.475 Mechanical “Q” (Qms) 7.243 Total Speaker “Q” (Qts) 0.446 Equivalent Compliance (Vas) 1.533 cu ft / 43.41 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.16% Efficiency (1 W / 1 m)** 84.2 dB SPL Effective Piston Area (Sd) 53.584 sq in / 0.0346 sq m DC Resistance (Re) 3.902 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 16.5 in / 419 mm External Height (H) 13.5 in / 343 mm External Depth (D) 7 in / 178 mm F3 43.1 Hz Fc 50.9 Hz Qtc 0.868 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.9 cu ft / 25.5 L External Width (W) 17.0 in / 432 mm External Height (H) 11.5 in / 292 mm External Depth (D) 15.25 in / 387 mm Internal Slot Port Width (SW) 1.125 in / 28.6 mm Internal Slot Port Height (SH) 10.0 in / 254 mm Internal Slot Port Length (SL) 30.1875 in / 767 mm Port Extension Length (EL) 12.50 in / 318 mm Tuning Frequency (Fb) 32.17 Hz F3 31.92 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 8-inch Subwoofer (150 W, 4 Ω) The 8W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (3.86 in. / 98 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 8-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 8W1v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a compact 0.350 cu. ft. (9.90 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 8.0 in / 200 mm Overall Diameter (A) 8.5 in / 216 mm Mounting Hole Diameter (B) 7.09 in / 180 mm Bolt Hole Circle Diameter (C) 7.85 in / 199 mm Motor Outer Diameter (D) 4.72 in / 120 mm Mounting Depth (E) 3.86 in / 98 mm Driver Displacement 0.018 cu ft / 0.51 L Net Weight 7.4 lb / 3.4 kg Parameters Free Air Resonance (Fs) 35.40 Hz Electrical “Q” (Qes) 0.451 Mechanical “Q” (Qms) 5.791 Total Speaker “Q” (Qts) 0.418 Equivalent Compliance (Vas) 0.68 cu ft / 19.26 L One-Way Linear Excursion (Xmax)* 0.3 in / 8 mm Reference Efficiency (no) 0.18% Efficiency (1 W / 1 m)** 84.8 dB SPL Effective Piston Area (Sd) 32.67 sq in / 0.0211 sq m DC Resistance (Re) 4.06 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.350 cu ft / 9.90 L External Width (W) 12 in / 305 mm External Height (H) 10 in / 254 mm External Depth (D) 8.625 in / 219 mm F3 59.9 Hz Fc 60.7 Hz Qtc 0.717 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.50 cu ft / 14.2 L External Width (W) 13.0 in / 330 mm External Height (H) 10 in / 254 mm External Depth (D) 11.125 in / 283 mm Internal Port Diameter (ID) 2 in / 51 mm Port Length (L) 10 in / 254 mm Tuning Frequency (Fb) 38 Hz F3 39.10 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

Custom-fit (CF) Speaker System: 3.5" (90 mm) Mid-Tweeter Engineered to deliver amazing sound from factory locations, CF speakers are designed with shallow polymer frames and breakaway mounting tabs for maximum compatibility in today's most popular vehicles, including those from Chevrolet, GMC, Cadillac, Dodge, Jeep, RAM, Toyota and many more.  CF drivers benefit from our proprietary FEA modeling and expertise in loudspeaker design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic low-distortion sound. At the core of the CF-350mt mid-tweeter is a proprietary 3.5" (90 mm) composite frame and a DMA-optimized motor system. An ultralight, fiber-reinforced pulp cone with a custom "S" roll surround delivers excellent efficiency and extended high-frequency response. A flat, progressive-roll spider ensures linear compliance, while the neodymium motor packs astonishing energy from an ultracompact and lightweight package. Each speaker's glass-filled, high-temperature polymer frame is outfitted with insert-molded terminals and a low-profile perforated metal grille to easily fit behind factory trim, while providing excellent UV protection in exposed dashboard locations. For passive applications as midtreble speakers, in-line second order high-pass filters are included to enhance smoothness and improve power handling. CF-350mt speakers can also be used actively as true midrange or mid-tweeter drivers to create outstanding two-way or three-way systems. For active applications, we recommend a high-quality digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, and the recommended bandwidths below. Design Bandwidth:With 24 dB/octave filters: 400 Hz-20 kHzWith 12 dB/octave filters: 500 Hz-20 kHz  Enjoy factory-fit and next-level sound from OEM locations with CF speakers! Speakers are sold as a pair and include built-in grilles. General Specifications Continuous Power Handling (RMS) 35 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 86.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 450 Hz - 20 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 3.46 in / 88 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 1.29 in / 33 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion (E) 0.26 / 7 mm Mounting Hole Diameter (F) 3.12 in / 80 mm Mounting Depth (G) 1.59 in / 40 mm *Does not take into account mounting tabs

Custom-fit (CF) Speaker System: 2.75" (70 mm) Mid-Tweeter Engineered to deliver amazing sound from factory locations, CF speakers are designed with shallow polymer frames and breakaway mounting tabs for maximum compatibility in today's most popular vehicles, including those from Chevrolet, GMC, Cadillac, Dodge, Jeep, RAM, Toyota and many more.  CF drivers benefit from our proprietary FEA modeling and expertise in loudspeaker design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic low-distortion sound. At the core of the CF-275mt mid-tweeter is a proprietary, 2.75" (70 mm) composite frame and a DMA-optimized motor system. An ultralight, fiber-reinforced pulp cone with a custom "S" roll surround delivers excellent efficiency and extended high-frequency response. A flat, progressive-roll spider ensures linear compliance, while the neodymium motor packs astonishing energy from an ultracompact and lightweight package. Each speaker's glass-filled, high-temperature polymer frame is outfitted with insert-molded terminals and a low-profile perforated metal grille to easily fit behind factory trim while providing excellent UV protection in exposed dashboard locations. For passive applications as midtreble speakers, in-line, second order high-pass filters are included to enhance smoothness and improve power handling. CF-275mt speakers can also be used actively, as true midrange or mid-tweeter drivers to create outstanding two-way or three-way systems. For active applications, we recommend a high-quality digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, and the recommended bandwidths below. Design Bandwidth:With 24 dB/octave filters: 400 Hz-20 kHzWith 12 dB/octave filters: 500 Hz-20 kHz Enjoy factory-fit and next-level sound from OEM locations with CF speakers! Speakers are sold as a pair and include built-in grilles. General Specifications Continuous Power Handling (RMS) 30 W Recommended Amplifier Power (RMS) 10 - 40 W / Ch. System Efficiency 82.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 450 Hz - 20 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 2.85 in / 72 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 1.29 in / 33 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion (E) 0.26 / 6.5 mm Mounting Hole Diameter (F) 2.48 in / 63 mm Mounting Depth (G) 1.39 in / 35 mm *Does not take into account mounting tabs

Two-way Component System: 6.5" (165 mm) Woofer, 1" (25 mm) Silk Dome Tweeter   Born from shared technologies used in our flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grilles C6 Tweeter Features:• Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General SpecificationsContinuous Power Handling (RMS)    100 WRecommended Amplifier Power (RMS)    25 - 150 W / Ch.System Efficiency    87.37 dB @ 1 W / 1 mSystem Nominal Impedance    4 ΩSystem Frequency Response    53 Hz – 21 KHz ± 3 dB   Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.11 in / 54 mm Flush Mount Mounting Hole Diameter (B) 1.85 in / 47 mm Flush Mount Mounting Depth (C) 1.85 in / 47 mm Flush Mount Protrusion (D1) 0.30 in / 8 mm Surface Mount Protrusion (D2) 1.04 in / 26 mm Crossover Physical Specifications Width (W) 3.36 in / 85 mm Height (H) 1.44 in / 37 mm Depth (D) 4.72 in / 120 mm

6.5" (165 mm) Component Woofer (with Grille) Born from shared technologies used in our flagship C7 speakers, the C6-650cw component woofer benefits from vast woofer design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-650cw component woofer features a proprietary cast alloy frame outfitted with our Elevated Frame Cooling™ technology and a DMA-optimized motor system to generate outstanding midbass impact with ultralow distortion. Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor, such as the JL Audio TwK® DSP, or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-650cw Component Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grille Design Bandwidth:With 48 dB/octave filters: 55 Hz-6 kHzWith 24 dB/octave filters: 65 Hz-6 kHzWith 12 dB/octave filters: 80 Hz-6 kHz Component woofers are sold individually and include a plastic grille tray, one fine steel mesh grille and one electroformed JL Audio badge logo. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 55 Hz - 6 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface

1" (25 mm) Silk Dome Component Tweeter Born from shared technologies used in our flagship C7 speakers, the C6-100ct component tweeter benefits from vast speaker design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-100ct component tweeter features an edge-driven, pure silk dome diaphragm for smooth, high-frequency performance with remarkable off-axis response and damping. A neodymium motor and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-100ct Component Tweeter Features:• Edge-driven pure-silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Design Bandwidth:With 48 dB/octave filters: 3-21 kHzWith 24 dB/octave filters: 4-21 kHzWith 12 dB/octave filters: 5-21 kHz Component tweeters are sold individually and include surface- and flush-mount fixtures and hardware. One 15 μF tweeter protection capacitor is also included.   General Specifications Continuous Power Handling (RMS) 75 W Recommended Amplifier Power (RMS) 25 - 100 W / Ch. Nominal Impedance 4 Ω Frequency Response 3 kHz - 21 KHz ± 3 dB Parameters Voice Coil Resistance (Re) 3.20 Ω Free Air Resonance (Fs) 1500 Hz Reference Efficiency (no) 0.602% Efficiency 90 dB @ 1W / 1m96 dB @ 1W / 0.5m Sensitivity 93 dB @ 2.83V / 1m Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.16 in / 55 mm Flush Mount Mounting Hole Diameter (B) 1.88 in / 48 mm Flush Mount Mounting Depth (C) 0.73 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.33 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 1.06 in / 27 mm

2-Way Component System: 6.5-inch (165 mm) Woofer, 1-inch (25 mm) Silk Dome Tweeter The C1-650se component system is engineered to deliver remarkable fidelity and outstanding value in a format that easily fits in factory locations. Outfitted with pure, silk dome tweeters, the C1-650se component system stands above others in its category with silky smooth, high-frequency clarity and definition. The 1-inch tweeter’s edge-driven design delivers excellent off-axis response and treble extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. Outboard, 3rd order, high-pass in-line filters, with Advanced Tweeter Protection Circuitry, are also included to guard against high-distortion damage and improve power handling. For maximum installation versatility, surface and flush tweeter mounts are also included.  C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low-distortion sound. At the core of the C1-650 woofer is a proprietary, stamped, steel 6.5-inch (165 mm) frame and DMA-optimized motor system. A mineral-filled, injection-molded, polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to each spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. To maximize fit, multi-application adaptor rings are included for the woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well.  When it comes to value, C1-650se is a real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 21 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.25 in / 159 mm Grille Tray Outer Diameter (B) 6.84 in / 174 mm Motor Outer Diameter (C) 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion** (E) N/A Mounting Hole Diameter (F) 5.02 in / 128 mm Mounting Depth (G) 2.07 in / 53 mm *Does not take into account mounting tabs**Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 1.97 in / 50 mm Surface Mount Fixture Diameter (A2) 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B) 1.75 in / 45 mm Flush Mount Mounting Depth (C) 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 0.87 in / 22 mm

Coaxial Speaker System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 91.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion** (D) 0.41 in / 10 mm Frontal Grille Protrusion (E) N/A Mounting Hole Diameter (F) N/A Mounting Depth (G) 2.75 in / 70 mm *Does not take into account mounting tabs**Frontal coaxial tweeter protrusion measured from mounting surface

Monoblock Class D Subwoofer Amplifier, 1500 W x 1 @ 1 - 2 Ω / 750 W x 1 @ 4 Ω - 14.4V Engineered for high-power, subwoofer applications, the RD1500/1 monoblock amplifier is built to deliver staggering amounts of world-class bass output. Equipped with a special low impedance circuit, the RD1500/1 is capable of generating a whopping 1500 watts of output power, at either 1 or 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1500 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1200 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >82 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1100 / 50 Hz Damping Factor @ 2 Ω >550 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 2 AWG wire Fuse Rating 150A (AFS or AGU)   Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.13 in / 54 mm Width (W) 18.05 in / 458 mm Depth (D) 6.96 in / 177 mm Net Weight

Monoblock Class D Subwoofer Amplifier, 1000 W x 1 @ 2 Ω / 600 W x 1 @ 4 Ω - 14.4V Designed to produce a serious 1000 watts into 2 ohms (14.4V, 1% THD), the JD1000/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion. The JD1000/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.  The JD1000/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.] Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 600 W RMS x 1 @ 3 Ω 800 W RMS x 1 @ 2 Ω 1000 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 500 W RMS x 1 @ 3 Ω 650 W RMS x 1 @ 2 Ω 800 W RMS x 1 @ 1.5 Ω N/A   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.10 in / 53 mm Width (W) 11.40 in / 290 mm Depth (D) 7.50 in / 190 mm Net Weight

The next in line after our passive 2-way kit 165W-RC, a leading product heralded for its performance for several years now, the 165W-XP integrates our exclusives technologies: TMD® surround, progressive spider, ventilated motor, new Beryllium tweeter, bi-amplification crossover. We also gave it a new design, steeped in our DNA and geared towards performance. The result: an uncompromising kit that opens the door to the world of Utopia. THE BEST OF FOCAL TECHNOLOGIES 'W' sandwich coneThe ‘W’ sandwich cone perfectly optimises the frequency response curve by fully mastering the three key parameters of lightness, rigidity and damping. When listening through the ‘W' sandwich cone, the sound is completely transparent with extremely little distortion. TMD® surround Originally developed for the Sopra line of high-fidelity loudspeakers, our TMD® (Tuned Mass Damper) surround has a unique profile, designed to better control the effects of resonance and to drastically reduce the distortion associated with deformations of the cone. The speaker driver takes advantage of this patented technology by spreading better defined and very realistic midranges.Progressive spiderThe progressive spider used on all our Utopia drivers is built around a progressive section that reproduces all the impact of the bass whilst optimising the linearity, precision and dynamics of the sound.Bi-amplification crossover All the components on our crossover have been specially selected and optimised to better control the effects of thermal dissipation. These components, essential for managing different channels and the soundstage, have improved reliability. As for the bi-amplification, this enables the woofer and tweeter to be driven separately in terms of power, resulting in optimum performance.  Type Separated 2-way passive kit Tweeter Beryllium Inverted dome Woofer (6 1/2") 165mm Cone 'W' Suspension Tuned Mass Damper (TMD®) Impedance 2Ω Max. power 200W Nom. power 100W Sensitivity (2.83 V/1 m) 93dB Frequency response 60Hz - 40kHz Accessories Grilles, screws and filters supplied TWEETER  6.5" WOOFER 

Manufactured in France Focal is known for innovative design and accurate sound, and they continue their impressive record of revolutionary hi-fi car audio with the K2 Power M Series. This single Focal SUB5KM 5-3/4" subwoofer is designed, engineered, and manufactured at Focal's facilities in France for true hi-fi sound in custom installations. The Focal SUB5KM subwoofer will serve up sizeable bass as part of your K2 Power M Series component system. Real presence Focal engineers applied some of their most innovative technologies, including an M-profile Aramid fiber cone, to make this tidy 5" sub uniquely equipped for maximum output, despite its small size. The shape and material help reduce harmonic distortion so you'll enjoy Focal's signature clean, unstressed, K2 sound. Focal also prioritizes shallow depth to make this special speaker a better fit for more installation locations. And with power handling up to 200 watts RMS, you can safely drive this sub with a healthy amount of power. Subwoofer Wiring Diagrams Product highlights: 5-3/4" 4-ohm component woofer (single) 'M'-profile Aramid fiber cone tuned mass damper surround super-rigid aluminum basket ferrite magnet handles up to 200 watts RMS (400 watts peak power) frequency response: 35-250 Hz sensitivity at 2.83V: 86 dB top-mount depth: 2-3/8" sealed box volume: 0.14-0.21 cubic feet grille not included warranty: 1 year MFR # SUB5KM Item # 091SUB5KM