C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with dual true, edge-driven, aluminium dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension. Both high-frequency drivers also benefit from the damping of a silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 36 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.94 in / 100 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 3.09 in / 79 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many “6-inch” speaker locations as well. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 48 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.25 in / 159 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 5.02 in / 128 mm Mounting Depth (G): 2.07 in / 53 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 54 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.83 in / 132 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.54 in / 14 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 4.70 in / 119 mm Mounting Depth (G): 2.42 in / 62 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 35 W Peak Music Power: 105 W Recommended Amplifier Power (RMS): 10 – 50 W / Ch. System Efficiency: 84.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 64 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 4.03 in / 102 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.33 in / 59 mm Frontal Coaxial Tweeter Protrusion** (D): 0.61 in / 16 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 3.70 in / 94 mm Mounting Depth (G): 1.81 in / 46 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

Steel mesh grille insert for select JL Audio 13-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 12-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for JL Audio 10-inch TW3 subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille insert for select JL Audio 10-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

Steel mesh grille inserts for select JL Audio 10-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer's rubber gasket ring.

Steel mesh grille insert for select JL Audio 8-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer's grille receiver ring.

Steel mesh grille insert for the 6W3v3 subwoofer driver. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer's grille receiver ring.

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-100ct component tweeter is designed to deliver unparalleled high-frequency performance. Utilizing a corundum ceramic-coated aluminium alloy diaphragm suspended via treated silk, s-roll surround, it provides spectacularly detailed reproduction of treble frequencies with an outstanding off-axis response. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Sold individually, with flush and surface mounting fixtures and hardware. One 15μF tweeter protection capacitor is also included. DESIGN FEATURES: Dome Diaphragm: Corundum ceramic-coated aluminium alloy diaphragm exhibits high stiffness, very low mass and excellent environmental stability. It also helps the tweeter dome to hold its shape and operate as a true piston at higher frequencies, without a penalty in moving mass. Suspension Design: The diaphragm’s motion is centred, sprung and damped by treated silk, s-roll surround. Ferrofluid in the magnetic gap acts as a rear suspension element in this design. The two combine to provide optimum damping without unduly restricting excursion. Motor Design: The C7-100ct employs a high-density magnetic circuit with a neodymium magnet and U-Yoke motor topology. An under-hung voice coil is employed, wound with copper-clad aluminium wire onto an aluminium voice coil former. Motor magnetics have been precisely optimized utilizing advanced FEA tools to lower even-order distortion and IMD/AMD. Acoustical Design: The shape of the tweeter housing is designed to boost sensitivity in a very specific bandwidth, helping to flatten the frequency response. It also provides improved control of directivity. DESIGN BANDWIDTH: With 48 dB/octave filters: 3,000 Hz – 30,000 Hz With 24 dB/octave filters: 4,000 Hz – 30,000 Hz With 12 dB/octave filters: 5,000 Hz – 30,000 Hz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 100 W Peak Music Power: 200 W Recommended Amplifier Power (RMS): 50 - 150 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 3 kHz - 30 KHz ± 3 dB Voice Coil Resistance (Re): 3.20 Ω Free Air Resonance (Fs): 1450 Hz Reference Efficiency (no): 0.267% Efficiency: 86.5 dB @ 1W / 1m | 92.5 dB @ 1W / 0.5m Sensitivity: 89.5 dB @ 2.83V / 1m Flush Mount Fixture Diameter (A1): 2.13 in / 54 mm Surface Mount Fixture Diameter (A2): 2.16 in / 55 mm Flush Mount Mounting Hole Diameter (B): 1.88 in / 48 mm Flush Mount Mounting Depth (C): 0.73 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.33 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2): 1.06 in / 27 mm

The smoothness and transparency of a high-end silk dome tweeter combine with top-flight component woofer performance to create a loudspeaker system with exceptional refinement and dynamic capability. The C5-650 component system features 6.5-inch (165 mm) component woofers with die-cast alloy baskets and Kurt Müller cones and suspensions. This woofer benefits from JL Audio’s vast woofer design experience and advanced modelling systems. The C5 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off-axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. The flush-mount fixtures feature our RSR (Ratcheting Swivel Rotation) mechanism to allow precise tweeter aiming after installation. C5 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 100 W Peak Music Power: 200 W Recommended Amplifier Power (RMS): 50 - 150 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 300 Hz - 10 KHz ± 3 dB Voice Coil Resistance (Re): 3.245 Ω Frame Outer Diameter (A): 3.45 in / 88 mm Bolt Hole Circle Diameter (B): 3.15 in / 80 mm Mounting Hole Diameter (C): 2.87 in / 73 mm Grille Tray Outer Diameter (D): 3.95 in / 100 mm Frontal Grille Protrusion (E): 0.58 in / 15 mm Mounting Depth (F): 1.46 in / 37 mm Motor Outer Diameter (G): 2.36 in / 60 mm

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Made in the USA with Global Components Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert DESIGN FEATURES: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high-frequency behaviour. Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw’s outstanding excursion capability. Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver’s performance range. A 32 mm (1.27 inch) diameter, the overhung voice coil is employed, wound with copper wire onto a fibreglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area and our patented Elevated Frame Cooling technology. DESIGN BANDWIDTH: With 48 dB/octave filters: 50 Hz – 5 kHz With 24 dB/octave filters: 60 Hz – 5 kHz With 12 dB/octave filters: 70 Hz – 5 kHz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 125 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 50 - 175 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 50 Hz - 5 KHz ± 3 dB Voice Coil Resistance (Re): 3.114 Ω Free Air Resonance (Fs): 54.5 Hz Reference Efficiency (no): 0.304% Efficiency: 87.0 dB @ 1W / 1m | 93.0 dB @ 1W / 0.5m Sensitivity: 90.0 dB @ 2.83V / 1m Electrical “Q” (Qes): 0.669 Mechanical “Q” (Qms): 6.265 Total Speaker “Q” (Qts): 0.605 Equivalent Compliance (Vas): 0.461 cu. ft. (13.05 liters) Moving Mass (Mms): 17.679 g Mechanical Compliance (Cms): 0.000482 m/N Magnetic Strength (BL): 5.31 N/A Effective Piston Area (Sd): 21.4 sq. in. (0.013807 sq. m) One Way Linear Excursion (Xmax): 5 mm

The TwK™ 88 is a state-of-the-art digital signal processor engineered to deliver world-class system tuning capabilities in an easy-to-use format. Equipped with an advanced 24-bit DSP processor, the TwK™ 88 includes flexible input/output options, 80 total bands of equalization and powerful mixing tools. The included DRC-200 Digital Remote Controller offers dual level controls, toggles up to six presets, and has an LED indicator. Control the TwK™ 88’s entire feature set by connecting it to your PC via USB, using the companion TüN™ Software interface. FEATURES: Flexible input design with 8 differential-balanced, line-level analog inputs (RCA), accepting line-level signals up to 7.1V (RMS) Separate optical (Toslink) and coaxial digital inputs for connection to digital S/PDIF sources Flexible input mixer allows input channels to be combined with full control over each input’s level and polarity 8 banks of 10-band graphic or parametric equalizers with configurable EQ assignment Powerful crossover section with fully variable, high-pass and low-pass filters, crossover slopes are selectable from 6 dB/octave to 48 dB/octave (in 6 dB/octave increments) Configurable polarity and delay settings, with separate entries for speaker distance plus offset control; fully linkable with other channels, in any combination, for adjustment Precise output level controls, adjustable in 0.5 or 0.1 dB increments, fully linkable with other channels, in any combination 8 analog, line-level RCA output jacks (4V RMS) Optical (Toslink) output jack provides a pass-through digital audio (S/PDIF) signal from any pair of input channels, with no signal processing applied Remote turn-on output (+12VDC) for activating aftermarket audio equipment JLid™ Port allows connection of the included DRC-200 Digital Remote Controller to add dual configurable level controls, preset selection and LED status reporting from the driver's seat SPECIFICATIONS: Power Supply Type: Regulated DC-DC SMPS Input Operating Voltage: 10 - 16 VDC Standby Current Draw: <1.5 mA Operating Current Draw: 0.7 A Recommended Fuse Value: 1 A Input Channels: 8 Input Type: Line-level, Differential-Balanced Input Voltage Range: 250 mV - 7.1 V RMS Minimum Input Voltage: 10 mV RMS Input Level Setting: 11 discrete selections from 250 mV - 7.1V RMS Output Channels: 8 Analog Output: Unbalanced, stereo RCA jacks Digital Output: Optical (Toslink) output (S/PDIF) Output Impedance: 450 Ω Latency Analog - Analog: 5.425 mS Latency Analog - Optical: 5.470 mS Latency Optical - Optical: 4.860 mS Latency Optical - Analog: 4.805 mS S/N Ratio: 98 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output: 0.02% (20 Hz - 20 kHz) Audio Resolution: 24 bit / 48 kHz Number of EQ Bands: 10 x 8 Channels Remote Level Control: Included (DRC-200) Remote Level Functions: Master Volume Control + Trim; Master Volume Control + Fader; Zone Control, LED Status Reporting

Some factory audio amplifiers employ a load detection circuit that looks for a low-impedance load in order to enable audio output. When a high-impedance load, like the input section of a FiX™ DSP, is connected to these factory amplifiers, the audio signal will mute. The FiX-LSA-4 is designed to provide a low enough load impedance to enable audio output in most of these situations. Simply disconnect the input connectors from the FiX™ DSP, insert the FiX-LSA-4 in-line and recalibrate with the FiX-LSA-4 in place. Note: An additional FiX-LSA-4 will be necessary if your FiX™ is connected to more than four channels of audio from your OEM head unit or amplifier.

The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs. By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Six (Front/Rear/Sub Output Pairs) Analog Output Unbalanced, stereo RCA jacks Digital Output N/A Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100 or DRC-200) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control) Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

The FiX™ 82 is a state-of-the-art digital signal processor engineered to deliver world-class sound from factory audio systems, without replacing the OEM source unit. The FiX™ 82 is the first DSP to automatically correct time delayed factory outputs prior to signal summing and EQ correction. With a powerful 24-bit DSP processor and dual 1/3 octave equalizers onboard, complex 2-way, 3-way and 4-way factory audio outputs are combined and level-matched automatically into a flat, full-range stereo signal. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Calibration is initiated with just a single button press and takes only about 30 seconds to complete, with no special equipment needed! By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access a pair of user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Output options include dual RCA jacks (4V RMS) or a digital optical (Toslink) output, supporting PCM audio (S/PDIF) at 24 bit/48 kHz resolution. Activation methods include 12-volt or automatic (Signal/DC-Offset Sensing), plus a dedicated remote turn-on output for activating your aftermarket equipment. Connect the optional DRC-100/205 Digital Remote Controller (sold separately) to add Master Volume Control capabilities from the driver’s seat. Clipped input signals and overall condition are also reported via the DRC-100’s multi-colour status LED. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Two Analog Output Unbalanced, stereo RCA jacks Digital Output Optical (Toslink) output (S/PDIF) Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

Somebody finally paid attention and designed a no-nonsense, back-to-basics sports car that puts the emphasis on driving enjoyment. Now all you need to do is add a healthy dose of JL Audio to ratchet up the listening enjoyment and make every drive even more memorable. Our patented 10TW3 thin-line driver is the engine inside this Stealthbox® system, and it produces spectacular results from its perch in the passenger side rear corner of the trunk. Your trunk remains completely useful and your installation is neat and secure. A grille is also included to protect your investment. GENERAL SPECIFICATIONS: Contains one 10TW3-D4 subwoofer in a sealed enclosure 400-watt power handling Wired for 2-ohm mono Installs in the passenger side of the trunk compartment Black steel mesh woofer grille is included

The latest all-American pony car gets a big dose of horsepower and major technology enhancements, all packaged in a new sleek and sexy body. Sadly though, the stock audio systems just can’t deliver enough bass to keep up with the Mustang’s high-performance muscle. Our Stealthbox® features an all-fibreglass, sealed enclosure design that fits in the same location as the optional factory subwoofer (and requires no holes to be drilled for installation). Equipped with our revolutionary 12TW3 thin-line subwoofer, this Stealthbox delivers deep, powerful bass that’s worthy of your Mustang’s heritage. GENERAL SPECIFICATIONS: Contains one 12TW3-D4 in a sealed enclosure 400-watt power handling. Wired for 2-ohm mono Installs in the passenger side rear corner of the trunk Factory subwoofer (if equipped) must be removed for installation of Stealthbox® Installation in Mustang Shelby GT350 models requires relocation of additional OEM equipment Will not fit convertible models

JL Audio’s patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output. In the HO112-W6v3, the high power handling of the 12W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification. JL Audio’s patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer’s direct output. This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 12W6v3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer. A steel mesh woofer grille insert can be purchased separately (Model: SGR-12W6v2/v3) if additional woofer protection is desired. GENERAL SPECIFICATIONS: Finish: Dark grey, high-grade automotive carpet, with black carpet on woofer baffle “JL AUDIO” is embroidered in silver on the side surface of the enclosure Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 600W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 600 W System Nominal Impedance 2 Ω Enclosure Type Chamber-coupled, slot-ported, rear-firing design Finish Dark grey carpet with black insert Grille Included: No External Width (W) 14.5 in / 368 mm External Height (H) 16 in / 406 mm External Depth (D1) 24 in / 610 mm Net Weight 60.7 lb / 27.52 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its dual 8W3v3 subwoofer drivers, each in separate airspace, with an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port for each driver wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The two flared port entries/exits, one on each end of the enclosure, further enhance sound quality by minimizing air-flow noises through these ports. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle Steel mesh grilles are included to protect the subwoofer drivers Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 500W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 500 W Enclosure Type Slot-ported, Low-profile External Width (W) 35.5 in / 902 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle A steel mesh grille is included to protect the subwoofer driver Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 – 250W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 250 W Enclosure Type Slot-ported, Low-profile Finish Black carpet External Width (W) 18.625 in / 473 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm Net Weight 17.40 lb / 7.89 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 6W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on the front baffle Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 50 – 150W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 150 W Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh External Width (W) 14.125 in / 359 mm External Height (H) 9.625 in / 245 mm External Depth (D1) 5.125 in / 130 mm Net Weight 12 lb / 5.44 kg

When the RBC-1 is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. Use it as a Subwoofer level control. INCLUSIONS: Rotary control with a black ABS knob, Mounting hardware 1x 18 ft. (5.5 m) cable COMPATIBLE WITH: RD500/1 RD1000/1 RD900/5

Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1000/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately). GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Height (H) 2.13 in / 54 mm Width (W) 14.66 in / 372 mm Depth (D) 6.96 in / 177 mm

Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is our proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion. For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Height (H): 2.13 in / 54 mm Width (W): 9.78 in / 248 mm Depth (D): 6.96 in / 177 mm

Crafted as an all-in-one, total system solution, the RD900/5 is engineered to power a complete audio system consisting of a subwoofer + four satellite system with 900 watts of high-performance sound. Equipped with our exclusive NexD™ switching technology, this complete power package efficiently generates a potent 70 watts of crystal-clear audio into 4 ohms, plus a robust 500 watts for a subwoofer system, all from a single compact chassis. Each pair of main channels is also fully bridgeable, stoutly producing 200 watts of full-range audio bliss (into 4 ohms), creating an ultra-powerful 3-channel amplifier. Conveniently located on top of the RD900/5, you’ll find a complement of studio-grade signal processing features, all hidden beneath a removable protective cover. Each pair of main channels is equipped with a 12 dB / octave high-pass filter, with a dedicated low-pass filter for its subwoofer channel. All three crossovers offer continuously variable frequency selection from 50-500 Hz, for precise filtering. Dual-range, differential-balanced inputs are also onboard, capable of accepting most input voltage levels, plus automatic turn-on capability (via signal sensing or DC-offset sensing) for maximum versatility. LED clipping indicators are also standard equipment for each channel section. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. The RD900/5 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can conveniently control the subwoofer’s output remotely from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response (Main Channels): 12 Hz – 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel): 10 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels): >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W: >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω: >150 / 50 Hz Damping Factor @ 2 Ω: >75 / 50 Hz THD+N @ Rated Power (Main Channels): <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels): <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs: Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge: 4 AWG wire Fuse Rating: 80 A (AFS, AGU or MaxiFuse™)

Utilizing our exclusive NexD™ high-speed switching technologies, the ultra-compact RD400/4 amplifier is engineered to deliver loads of audio output power, with incredible efficiency and low distortion. Don’t let its modern styling and small size fool you though, this little powerhouse churns out 100 watts of crystal-clear audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms. For your convenience, the RD400/4’s controls can be found on top of the amplifier, beneath a protective cover, with all connections located along one side of its chassis. Studio-grade signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment, along with all-new input type switches for bridging of stereo output channels without needing to use Y-adaptors. Onboard LED-clipping indicators are also included with your RD400/4. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity settings, quickly and accurately, with no special equipment needed. You’ll also find a set of preamp outputs on-hand, so you can pass signals to another amplifier, almost effortlessly. The RD400/4 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. GENERAL SPECIFICATIONS: Frequency Response 12 Hz – 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge: 4 AWG wire Fuse Rating: 40 A (AFS, AGU or MaxiFuse™)

The DRC-205 is a panel-mount, wired digital remote controller designed to connect to the JLid™ port of compatible JL Audio electronics. The specific audio functionality of the DRC-205 controller will be determined by the device it is connected to. COMPATIBLE WITH: FiX™ OEM Integration DSP: All models TwK™ System Tuning DSP: All models VXi-Series Amplifiers: All models FUNCTIONS: Dual-concentric rotary controls with stops Push-button mode selector Status indicator (RGB LED) COMMON USES INCLUDE: Master Volume Subwoofer Volume Preset or Mode Selection

The DRC-100 is a panel-mount, wired digital remote controller designed to connect to the JLid™ port of compatible JL Audio electronics. The specific audio functionality of the DRC-100 controller will be determined by the device it is connected to. COMPATIBLE WITH: FiX™ OEM Integration DSP: All models VXi-Series Amplifiers: All models FUNCTIONS: Rotary knob with stops Push-button mode selector Status indicator (RGB LED) COMMON USES INCLUDE: Master Volume Subwoofer Volume Preset or Mode Selection

FEATURES: JLid™ Bluetooth® Communicator for VXi Amplifiers Tune your VXi amplifier via a Bluetooth device Not for Streaming or Hands Free

The VXi amplifier ecosystem is designed to be very flexible, offering users almost limitless combinations of amplifiers and channel architectures, along with the amazing power of its integrated DSP technology. VXi-HUB is an accessory designed to simplify the control of a networked amplifier system, while greatly easing the setup process, by allowing all amplifiers to appear in a single TüN™ software session. VXi-HUB performs two distinct functions as part of a system employing two or more VXi amplifiers: data networking and digital audio distribution. Data networking is the primary function of the VXi-HUB, permitting a network of VXi amplifiers to respond to synchronized commands from a single DRC controller (DRC-100, DRC-200 or DRC-205, all sold separately). These commands can include Master Volume, Subwoofer Level, Fader, Zone Level and Preset Selection. The VXi-HUB also enables the networked VXi amplifiers to be tuned from within a single TüN™ software session, allowing the user to quickly switch between amplifiers during the tuning process, without disconnecting and connecting multiple cables. For data networking purposes, the VXi-HUB is equipped with one Master and five Slave JLid-COMM connections, permitting the networking of up to six VXi amplifiers using standard CAT5e cables (one master amplifier and five slave amplifiers). For more complex systems, two VXI-HUBs can be daisy-chained to create a network of up to ten VXi amplifiers (one master amplifier and nine slave amplifiers). VXi-HUB also includes a dedicated JLid-COMM accessory port to allow the connection of the optional VXi-BTC Bluetooth® Communicator (sold separately). This accessory enables convenient wireless setup and tuning of the entire amplifier network using a compatible iOS® or Android® device with TüN™ Mobile or TüN™ Express apps. The secondary function of the VXi-HUB is to distribute synchronous optical digital audio signals to the networked amplifiers, avoiding the delays associated with handing digital signals off through a chain of amplifiers. The optical digital audio output of a source unit connects directly to the VXi-HUB’s Optical Audio Input, which then distributes synchronous digital audio to the amplifiers from its five Optical Outputs. VXi-HUB handles S/PDIF signals up to 24 bits/192 kHz. For ease of connection, the VXi-HUB is powered via the JLid™ connection to VXI amplifiers and requires no separate power or turn-on wiring. FEATURES: JLid-COMM Connections: 1 Master Input / 5 Slave Outputs / 1 Accessory Port Optical Audio (S/PDIF) Connections: 1 Input / 5 Synchronous Outputs 3-way Configuration Switch: Standalone / Primary / Secondary Amp Identifier Status LEDs Powered via JLid™ connection to VXi amplifiers

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. The VX1000/1i monoblock subwoofer amplifier outputs up to 600 watts into 4 ohms, or a jaw-dropping 1000 watts into 2 ohms. A specialized, low-frequency version of our NexD2™ amplifier technology delivers rock-solid bass performance and fidelity, with outstanding efficiency. Compact dimensions with all connections placed on one side, via mating plugs, greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Subwoofer Output Connector 6 ft A/B USB Cable

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX400/4i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up to 200 W x 2. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 4 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness 6 ft A/B USB Cable

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX600/6i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms, producing up a rock-solid 200 W x 3. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 4 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness 6 ft A/B USB Cable

NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. With our second-generation NexD2™ technology, the VX800/8i full-range amplifier outputs up to 75 watts per channel into 4 ohms, or 100 watts into 2 ohms. It can also be bridged into 4 ohms to deliver a powerful 200 W x 4. The NexD2™ full-range technology in this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harnesses (2) 6 ft A/B USB Cable

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. Employing our second-generation NexD2™ amplifier technology, the VX1000/5i efficiently powers a complete audio system. It can drive four main speakers with 75 W x 4 @ 4 ohms while also powering a subwoofer with up to 600W @ 2 ohms. Bridging the main channels converts it into a very powerful, 3-channel system amplifier with up to 200W x 2 @ 4 ohms on the main channels and 600W @ 2 ohms on the subwoofer channel. The NexD2™ full-range technology in the main channels of this amplifier is DSP-controlled and features a reduced loop area design utilizing DirectFET™ outputs for outstanding fidelity, very low noise and exceptional efficiency. The subwoofer channel features an optimized low-frequency variant of the NexD2™ technology. The amplifier chassis is ultra-compact, with all connections on one side, to greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Speaker Output Harness Subwoofer Output Connector 6 ft A/B USB Cable

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω  

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 250WNominal Impedance: 4 Ω

While extremely compact, this amazing amplifier will comfortably drive a complete high-performance car audio system: that is, four satellite speaker systems and a subwoofer system... with a very serious 900 watts of power! Using our Single Cycle Control switching design and R.I.P.S. technology, the HD900/5 delivers 100 W x 4 to its four main channels, plus a very meaty 500 W to its subwoofer channel. Thanks to R.I.P.S., high power can be delivered over a wide range of load impedances, while the tight power supply regulation keeps distortion down, maximizing sound quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. Main Channels @ 4 Ω 100 W RMS x 4 Main Channels @ 3 Ω 75 W RMS x 4 Main Channels @ 2 Ω 75 W RMS x 4 Main Channels @ 1.5 Ω 75 W RMS x 4 Main Channels - Bridged @ 8 Ω 200 W RMS x 2 Main Channels - Bridged @ 4 Ω 150 W RMS x 2 Subwoofer Channel @ 4 Ω 500 W RMS x 1 Subwoofer Channel @ 3 Ω 500 W RMS x 1 Subwoofer Channel @ 2 Ω 500 W RMS x 1 Subwoofer Channel @ 1.5 Ω 500 W RMS x 1

JL Audios most powerful HD amplifier employs our advanced Single-Cycle Control switching design and R.I.P.S. technology to deliver 1200 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. While targeted primarily to subwoofer applications, the HD1200/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. @ 4 Ω 1200 W RMS x 1 @ 3 Ω 1200 W RMS x 1 @ 2 Ω 1200 W RMS x 1 @ 1.5 Ω 1200 W RMS x 1

This ultra-compact monoblock amplifier employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 750 W of clean power into any impedance between 1.5 and 4 Ω, giving you the highest degree of flexibility in designing your subwoofer system. Tight power supply regulation keeps distortion down and maximizes your bass quality. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. While targeted primarily to subwoofer applications, the HD750/1 is a wide-range amplifier and can also be used to drive high-performance mid-range speaker systems. This amplifier features a brushed aluminium finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls. @ 4 Ω 750 W RMS x 1 @ 3 Ω 750 W RMS x 1 @ 2 Ω 750 W RMS x 1 @ 1.5 Ω 750 W RMS x 1

This compact multi-channel powerhouse employs our Single-Cycle Control switching design and R.I.P.S. technology to deliver 150 W x 4 or 300 W x 2. Tight power supply regulation keeps distortion down and maximizes sound quality. When using the HD750/1 or HD1200/1 to drive a subwoofer system, the HD600/4 is the ideal satellite amplifier, delivering huge dynamics with pristine resolution. From a pure sound quality perspective, we invite you to compare the real-world, in-car performance of this amplifier to any other amplifier on the market, of any type, at any price. It can also be deployed on its own as a very capable 3-channel system amplifier with 150 W x 2 to the satellites and 300 W x 1 to a subwoofer system. This amplifier features a brushed aluminum finish with black powder-coated cast alloy heat sinks and bottom panel. A black powder-coated, gasketed cover is also provided to protect the controls.

The HD-RLC remotely controls the Bass Level of the following JL Audio amplifiers: HD-Series: All modelsXD-Series: All modelsMHD-Series: All modelsM-Series: All models When the HD-RLC is connected to the above amplifiers, it acts as an attenuator on the input gain of the amplifier and is used to adjust the overall level of the amplifier from the front of the vehicle. The HD-RLC kit includes the rotary control with a black ABS knob, mounting hardware and one 18 ft. (5.5 m) cable.

There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The new C3-600 expands the C3 lineup with a direct-fit product for many Japanese vehicles that will not accept a full-size 6.5-inch speaker. The C3-600 system features 6-inch (150 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-molded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 89.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 50 Hz - 25 KHz ± 3 dB

There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. Many people mistakenly believe that an oval speaker cannot perform as well as around one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C3-570 system features 5 x 7 / 6 x 8-inch (125 x 180 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-moulded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are not available for this product. Sonic character: Clean and Powerful Sold as a pair. Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB

There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-525 system features 5.25-inch (130 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-moulded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and long linear excursion woofer deigns. The C2-600 system features 6-inch (150 mm) component woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modeling systems. The 6-inch (150 mm) format is a direct fit in many Japanese vehicles where a full-size 6.5-inch speaker (165 mm) will not fit without modification. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6-inch (150 mm) speaker. The C2 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. C2 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Three levels of tweeter attenuation are provided, as well as a tweeter protector. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB