is here! Shop now, pay later in 4 easy installments
ⓘ
10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear...
10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils)
Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does.
Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level.
Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab.
W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences:
| Continuous Power Handling (RMS) | 1500 W |
| Recommended Amplifier Power (RMS) | 500 - 1500 W |
| Nominal Impedance (Znom) | Dual 1.5 Ω |
| Nominal Diameter | 13.5 in / 345 mm |
| Overall Diameter (A) | 14 in / 356 mm |
| Mounting Hole Diameter (B) | 11.9 in / 302 mm |
| Bolt Hole Circle Diameter (C) | 12.7 in / 323 mm |
| Motor Outer Diameter (D) | 8.38 in / 213 mm |
| Mounting Depth (E) | 10.5 in / 267 mm |
| Driver Displacement | 0.21 cu ft / 5.9 L |
| Net Weight | 52 lb / 23.6 kg |
| Free Air Resonance (Fs) | 23.5 Hz |
| Electrical “Q” (Qes) | 0.476 |
| Mechanical “Q” (Qms) | 7.517 |
| Total Speaker “Q” (Qts) | 0.448 |
| Equivalent Compliance (Vas) | 3.68 cu ft / 104.3 L |
| One-Way Linear Excursion (Xmax)* | 1.25 in / 32 mm |
| Reference Efficiency (no) | 0.27% |
| Efficiency (1 W / 1 m)** | 86.3 dB SPL |
| Effective Piston Area (Sd) | 107.35 sq in / 0.0693 sq m |
| DC Resistance (Re)*** | 2.41 Ω |
|
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied. |
|
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 1.0 in / 25 mm |
| Volume (net int.) | 1.875 cu ft / 53.1 L |
| External Width (W) | 16 in / 407 mm |
| External Height (H) | 16 in / 407 mm |
| External Depth (D) | 18.875 in / 479 mm |
| F3 | 37.4 Hz |
| Fc | 40.5 Hz |
| Qtc | 0.77 |
|
Enclosure Notes * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety Notice |
|
| Wall Thickness | 0.75 in / 19 mm |
| Front Baffle Thickness | 1.0 in / 25 mm |
| Volume (net int.) | 2.375 cu ft / 67.3 L |
| External Width (W) | 25.875 in / 657 mm |
| External Height (H) | 16 in / 406 mm |
| External Depth (D) | 17.25 in / 438 mm |
| Internal Slot Port Width (SW) | 2.25 in / 57 mm |
| Internal Slot Port Height (SH) | 14.5 in / 368 mm |
| Internal Slot Port Length (SL) | 26.25 in / 667 mm |
| Port Extension Length (EL) | 7.875 in / 200 mm |
| Tuning Frequency (Fb) | 34.6 Hz |
| F3 | 30.3 Hz |
|
Enclosure Notes * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety Notice |
|
Glen and the guys did an amazing job installing a towbar and wiring kit on my vehicle. Well priced and they turned it around in a few hours on pretty short notice. Highly recommend.
Big shout out to the boys at TJM Northern Beaches. A great job for my suspension upgrade. Knowledgeable, greate communication, workmanship and efficiency. Very happy with the result.
Great team effort from Sales, Installation, and aftersales in looking after my GVM upgrade on my LC 300 GRS. Many thanks team
For all 4x4 advice, products and service, look no further than TJM Northern Beaches in Brookvale. Jason has built a fantastic team of professionals who have both in-depth technical knowledge and experience and demonstrate some of the best customer service skills I’ve seen. They beat their competitors in this area hands down. Jason was fantastic with helping me design and specify my Y62 Patrol build earlier this year and was very honest about what they could do / supply and things that I would be better sourcing from other suppliers. Throughout the build, he provided solutions, not problems particularly regarding a pre rego GVM upgrade. He was great in communicating progress and working with Nissan to ensure all the work was completed prior to registration. A big shout out also to Andy and Ed in the workshop who were very patient and helpful in providing me with an operational handover once it was complete. They have also provided great after sales service. I’ll definitely be going back to TJM Brookvale for all my 4x4 needs and highly recommend them – no need to look further. Well done team!
Great service and workmanship. Jason and his team looked after me very well. answered questions and emails promptly.I would recommend these guys!
The team just completed a heap of 12v work on my new car after doing work on my previous one. The workmanship as usual was first class and I can't recommend them highly enough. Given my Ineos is a brand new car to market they took the time and care to ensure it was completed professionally and exactly to my requirements.
The best 4WD shop in Sydney, cannot recommend more. Jason and Des are absolutely legend. They are very helpful and professional, Giving me the best options and keep everything on track. The boys from the workshop also provide high quality workmanship, and easy communication. They supply large range of high quality brands like Jmacx, RVSS, Enerdrive etc, your true one stop shop. I should build with them from the start, it would be much easier!
Phoned in the morning… with the roof top tent in stock… dropped vehicle off at lunch, and had it back that afternoon. Need I say more!? Thanks gents!
Jase, Glen and Des were a massive help after losing my car in the floods.
My 2022 D’max had a bullbar, winch and lift kit fitted and it looks and feels amazing! The guys at TJM Brookvale made every effort to get the work on my car done the second my car was off the boat and at the dealership and turned it around in a very short time, as they knew it was hurting me having no car, not to mention did it all at a very reasonable price. I can’t overstate how good these guys are. I will definitely be a repeat customer! Grateful to these blokes.
Thanks Glen and your team for an excellent first class service. Very price competitive as well.
The lads helped me out last minute to install my rooftop tent. They had all the necessary tools & equipment and were super friendly and helpful. Thanks guys!!
Got my TJM Outback bull bar, Rock slides & 2” lift with them in Brookvale.
Glen and the team are first class.
$132.00
