DIRECTION-PLUS Transchill Arctic Black Transmission Cooler Kit Land Cruiser 200...
$552.60
$614.00
The NEW 32mm 14 row TransChill Arctic Black Transmission cooler kit TCB615DPK fits Toyota Landcruiser 200 Series models and is designed specifically to reduce excessive transmission heat caused by towing, carrying loads and driving in sand, snow, off-road or hot conditions.
The TransChill Arctic Black Transmission cooler is an effective & economical way to keep the transmission at its optimum operating temperature. High efficiency turbulators in each tube direct the fluid for superior heat transfer. The unique 32mm plate & fin design allows for extreme cooling whilst the compact design is perfect for our vehicle specific mounting.
New & Improved model
Designed and engineered in Australia
32mm, 14 row fin & plate design allows for extreme cooling
Durable Black powder coat resists oxidisation
100% pressure tested at 150psi for quality assurance
Internal tubulation for efficient heat transfer
Up to 50% more efficient (*heat transfer rate – BTU/hr)
Pre-drilled mounting plates for easy installation
Inlet & Outlet size: M16 fittings
WHY DO YOU NEED ONE?
Due to the extreme heat generated in an automatic transmission, an auxiliary oil cooler is an economical and efficient way to help protect against costly transmission repairs.
Automatic Transmission Fluid (ATF) cools, lubricates and cleans internal transmission components. When transmission components exceed 93°C (200°F) the performance of ATF is seriously compromised.
Subsequently the life span of the ATF, seals and internal components of the transmission are significantly reduced. Higher internal temperatures also increase the wear rate of the friction and clutch plates.
HOW IT WORKS
The Direction-Plus™ Transmission Cooler Kit can reduce the temperature of the ATF by as much as 33°C and assist maintaining acceptable operating temperatures. A reduction of just 11°C that can double the life expectancy of the transmission, ATF and all internal components.
AUTOMATIC TRANSCHILL CONTENTS:
Vehicle specific laser cut 4mm 5005-H34 aluminum mounting brackets
All mounting hardware included
ATF Hose (Meets or exceeds SAE J1019 requirements)
1x Davies Craig Black 32mm 14 row oil cooler
3yr Warranty *Conditions apply
FRONT RUNNER Under Rack Table - TBRA035
$551.70
$613.00
The lightweight Under Rack Table was engineered to be easily stored underneath most Front Runner Slimline II Roof Racks leaving more space for your gear on top. This lightweight, sturdy full-sized Under Rack Table is ideal for food preparation, food serving, and gathering around for a sit-down camp dinner. Features include an aluminium PVDF top and black powder-coated aluminium and high-strength steel frame.
DIRECTION-PLUS Transchill Arctic Black Transmission Cooler Kit Nissan Navara Np300...
$551.70
$613.00
The NEW & IMPROVED 32mm 14 row Arctic Black TransChill Transmission Oil Cooler Kit (TCB630DPK) suits the Nissan Navara NP300 YS23DTTi (2.3L 4cyl) 2015- On models and is designed specifically to reduce excessive transmission heat caused by towing, carrying loads and driving in sand, snow, off-road or hot conditions.
The 32mm TransChill Transmission cooler is an effective & economical way to keep the transmission at its optimum operating temperature. High efficiency turbulators in each tube direct the fluid for superior heat transfer. The unique 32mm plate & fin design allows for extreme cooling whilst the compact design is perfect for our vehicle specific mounting.
Designed and engineered in Australia
32mm, 14 row fin & plate design allows for extreme cooling
Durable Black powder coat resists oxidisation
Pressure tested at 150psi for quality assurance
Internal tubulation for efficient heat transfer
75% more performance than a comparable tube and fin design (*heat transfer rate – BTU/hr)
Pre-drilled mounting plates for easy installation
Inlet & Outlet size: M16 fittings
WHY DO YOU NEED ONE?
Due to the extreme heat generated in an automatic transmission, an auxiliary oil cooler is an economical and efficient way to help protect against costly transmission repairs.
Automatic Transmission Fluid (ATF) cools, lubricates and cleans internal transmission components. When transmission components exceed 93°C (200°F) the performance of ATF is seriously compromised.
Subsequently the life span of the ATF, seals and internal components of the transmission are significantly reduced. Higher internal temperatures also increase the wear rate of the friction and clutch plates.
HOW IT WORKS
The Direction-Plus™ Transmission Cooler Kit can reduce the temperature of the ATF by as much as 33°C and assist maintaining acceptable operating temperatures. A reduction of just 11°C that can double the life expectancy of the transmission, ATF and all internal components.
AUTOMATIC TRANSCHILL CONTENTS:
Australian Made vehicle specific laser cut 4mm 5005-H34 aluminum mounting brackets
Locally designed and packed with all the mounting hardware required for a DIY installation
ATF Hose (Meets or exceeds SAE J1019 requirements)
1x Davies Craig Black 32mm 14 row oil cooler
3yr Warranty *Conditions apply
FRONT RUNNER Land Rover Discovery 1And2 Load Bar Kit /...
$549.00
$610.00
A set of Gutter Mounted Load Bars used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 265mm Gutter Mount legs, 2 1425mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to a vehicle with gutters.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner load bars.
Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.
The Load Bars are mounted directly to the rain gutters using Gutter Mounted Legs.
Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The Load Bars and Gutter Mount Legs can be used in the future as components to build a complete Front Runner Roof Rack.
Made from stainless steel and a durable, weather resistant black powder-coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Features
KRLD026 - Land Rover Discovery 1&2 Load Bar Kit / Gutter Mount - by Front Runner
Consisting of:
2 x LASS109 - No 9 Leg 265mm (Pair) - by Front Runner
1 x LBSK016 - Roof Load Bar Pair 1425mm(W) - by Front Runner
1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 8kg (18lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 130mm (5")
Length 1540mm (61")
Height 195mm (8")
Shipping Weight:
Weight 9.7kg (21.4lbs)
DIRECTION-PLUS Ryco Pre-Filter Kit Land Cruiser 70 Series () -...
$549.00
$610.00
Direction Plus™ Ryco Pre-Filter Kit RC648DPK is designed, engineered & assembled in Australia to suit Toyota Landcruiser 70 series 1GD-FTV 2.8L 4cyl (2023 – On) models, protecting its engine against costly injector failure. Diesel contains more impurities than petrol, necessitating optimal filtration. This is crucial, especially while towing, taking your vehicle off-road, or accessing fuel of uncertain quality in remote areas. While the OE filter works well for many contaminants, it has limitations against water and other particles.
This kit fits:
Toyota Land Cruiser 70 Series 1GD-FTV (2.8L 4cyl) 2023 – On
Driver side mounting location.
PROTECT YOUR ENGINE
It’s easy to think that fuel contamination is something that happens “in the bush” but this is simply not true!
Did you know that 72% of all diesel fuel injection system failures are caused by water and fuel lubricity problems?
Direction Plus™ Ryco Pre-Filter kits are designed for modern high pressure fuel systems with a lift pump in the tank, offering 10-micron filter media, effectively removes 99% water and 98% particles from diesel fuel, providing maximum efficiency, life and flow to your vehicle’s fuel system. This protects the main fuel filter and engine from contamination-related damage. By fitting the Wireless Sensor Kit, it is a true fit-and-forget install, where you can monitor your pre-filter kit remotely, no longer having to look under the bonnet where space is restricted to check the bowl for water.
HOW IT WORKS
Installing a Direction Plus™ Ryco Pre-filter kit between the fuel tank and the O.E.M fuel filter, effectively removes 99% water and 98% particles from diesel fuel providing maximum efficiency, life and flow to your vehicle’s fuel system. This also leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system.
For the ultimate front line defence against water and particle contamination, investing in a Direction Plus™ Ryco Pre-Filter Kit will protect your investment 24 hours a day, 365 days a year.
BENEFITS OF A RYCO PRE-FILTER KIT:
Isolate water before it journeys through your fuel system causing damage.
Protect your fuel system from corrosion of metal components that left unaddressed
can cause expensive damage to your fuel system.
Reduce micro-bacterial growth caused by water contamination, which can reduce
engine durability and performance.
Remove other contaminants down to 10 microns, meaning your OE filter does not
have to work as hard.
Water resistant silicone coated filter media provides maximum efficiency, life and flow
Maximum working Pressure 87 PSI/6 bar/600 kPa
Give you a visible or audible alert to water in your fuel system allowing you to take
action to protect your engine (when used with S102XK and S101X accessories).
Allow you to easily drain water from your fuel system multiple times to get to safety
or a mechanical workshop.
Tested in the Ryco lab to meet or exceed OE equivalents and to international ISO and SAE standards
Check fitment guide below to confirm suitability for your vehicle.
DIRECTION-PLUS Ryco Pre-Filter Kit Land Cruiser 70 () - RC642DPK
$547.20
$608.00
Direction Plus™ Ryco Pre-Filter Kit RC642DPK is designed, engineered & assembled in Australia to suit Toyota Landcruiser 70 series 1VD-FTV (2018-2022) models, protecting its engine against costly injector failure. Diesel contains more impurities than petrol, necessitating optimal filtration. This is crucial, especially while towing, taking your vehicle off-road, or accessing fuel of uncertain quality in remote areas. While the OE filter works well for many contaminants, it has limitations against water and other particles.
This kit fits:
Toyota Land Cruiser 70 Series 1VD-FTV (4.5L 8cyl) 2018 – On
Driver side mounting location.
PROTECT YOUR ENGINE
It’s easy to think that fuel contamination is something that happens “in the bush” but this is simply not true!
Did you know that 72% of all diesel fuel injection system failures are caused by water and fuel lubricity problems?
Direction Plus™ Ryco Pre-Filter kits are designed for modern high pressure fuel systems with a lift pump in the tank, offering 10-micron filter media, effectively removes 99% water and 98% particles from diesel fuel, providing maximum efficiency, life and flow to your vehicle’s fuel system. This protects the main fuel filter and engine from contamination-related damage. By fitting the Wireless Sensor Kit, it is a true fit-and-forget install, where you can monitor your pre-filter kit remotely, no longer having to look under the bonnet where space is restricted to check the bowl for water.
HOW IT WORKS
Installing a Direction Plus™ Ryco Pre-filter kit between the fuel tank and the O.E.M fuel filter, effectively removes 99% water and 98% particles from diesel fuel providing maximum efficiency, life and flow to your vehicle’s fuel system. This also leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system.
For the ultimate front line defence against water and particle contamination, investing in a Direction Plus™ Ryco Pre-Filter Kit will protect your investment 24 hours a day, 365 days a year.
BENEFITS OF A RYCO PRE-FILTER KIT:
Isolate water before it journeys through your fuel system causing damage.
Protect your fuel system from corrosion of metal components that left unaddressed
can cause expensive damage to your fuel system.
Reduce micro-bacterial growth caused by water contamination, which can reduce
engine durability and performance.
Remove other contaminants down to 10 microns, meaning your OE filter does not
have to work as hard.
Water resistant silicone coated filter media provides maximum efficiency, life and flow
Maximum working Pressure 87 PSI/6 bar/600 kPa
Give you a visible or audible alert to water in your fuel system allowing you to take
action to protect your engine (when used with S102XK and S101X accessories).
Allow you to easily drain water from your fuel system multiple times to get to safety
or a mechanical workshop.
Tested in the Ryco lab to meet or exceed OE equivalents and to international ISO and SAE standards
Check fitment guide below to confirm suitability for your vehicle.
FRONT RUNNER Isuzu D-Max (2012-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
Clear your bed space and still haul your adventure gear and toys over your Isuzu D-Max EGR RollTrac roll cover.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Isuzu D-Max when fitted with a EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
KRRT006 - Isuzu D-Max (2012-Current) EGR RollTrac Load Bed Load Bar Kit - by Front RunnerConsisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK017 - Roof Load Bar Pair 1475mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 8.24kg (18.17lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 160mm (6")Length: 1585mm (62")Height: 165mm (6")Shipping Weight:Weight: 8.6kg (19lbs)
FRONT RUNNER Ford Ranger (2012-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
Clear your bed space and still haul your adventure gear and toys over your Ford Ranger load bed when fitted with an EGR RollTrac roll cover.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Ford Ranger when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
* Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
Consisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK017 - Roof Load Bar Pair 1475mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 8.08kg (17.81lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 160mm (6")Length: 1590mm (63")Height: 160mm (6")Shipping Weight:Weight: 8.4kg (18lbs)
FRONT RUNNER Nissan Navara (2014-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Nissan Navara when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT009 - Nissan Navara (2014-Current) EGR RollTrac Load Bed Load Bar Kit
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 8.54kg (18.83lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1590mm (63")
Height: 160mm (6")
Shipping Weight:
Weight: 8.4kg (18lbs)
FRONT RUNNER Volkswagen Amarok (2010-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Volkswagen Amarok when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT010 - Volkswagen Amarok (2010-Current) EGR RollTrac Load Bed Load Bar Kit - by Front Runner
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 8.54kg (18.83lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1585mm (62")
Height: 165mm (6")
Shipping Weight:
Weight: 8.6kg (19lbs)
FRONT RUNNER Toyota Hilux (2016-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Toyota Hilux when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT011 - Toyota Hilux (2016-Current) EGR RollTrac Load Bed Load Bar Kit - by Front Runner
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 8.08kg (17.81lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1585mm (62")
Height: 165mm (6")
Shipping Weight:
Weight: 8.6kg (19lbs)
FRONT RUNNER Ute Roll Top Load Bar Kit /1475Mm (W)...
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your truck when fitted with a Roll Top cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the OEM tracks of your Roll Top cover, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the Roll Top cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT004 - Pickup Roll Top Load Bar Kit /1475mm (W)
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 8.38kg (18.47lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6"); Length: 1590mm (63"); Height: 150mm (6")
Shipping Weight:
Weight: 8.2kg (18lbs)
FRONT RUNNER Toyota Tundra 6.4' Crew Max (2007-Current) Double Load...
$543.60
$604.00
Transport all your adventure gear safely over the bed of your Toyota Tundra Crew Max with this pair of strong, sleek, low-profile Pickup Bed Load Bars.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Toyota Tundra Crew Max. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Consisting of:
2 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner1 x LBSK018 - Roof Load Bar Pair 1575mm(W) - by Front Runner1 x RRAC901 - Load Bed Nut Kit / Toyota Tacoma 2004+/Tundra 2007+ - by Front Runner
Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steel
Approximate Installed Weight: 8.5kg (18.8lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 1685mm (66.0")Length: 150mm (6.0")Height: 200mm (8.0")
Shipping Weight:8.4kg (18.0lbs)
FRONT RUNNER Toyota Tundra 5.5' Crew Max (2007-Current) Double Load...
$543.60
$604.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Toyota Tundra Crew Max. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Features
KRTT961 - Toyota Tundra 5.5' Crew Max (2007-Current) Double Load Bar Kit - by Front Runner
Consisting of:
2 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner
1 x LBSK018 - Roof Load Bar Pair 1575mm(W) - by Front Runner
1 x RRAC901 - Load Bed Nut Kit / Toyota Tacoma 2004+/Tundra 2007+ - by Front Runner
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 8.5kg (18.8lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 1685mm (66.0")
Length: 150mm (6.0")
Height: 200mm (8.0")
Shipping Weight:
8.4kg (18.0lbs)
DIRECTION-PLUS Preline And Pre-Filter System Bt-50 - PL645DPK
$542.70
$603.00
Direction-Plus™ PreLine-Plus PL645DPK is an innovative pre-filter system for diesel fuel which suits Isuzu D-Max, MU-X and Mazda Bt-50 4JJ3-TCX (2020-2022) models. PreLine-Plus pre-filter system is designed specifically to cope with extreme weather conditions and poor fuel quality ensuring a high degree of water separation and particle pre-separation.
With a 100% water separation efficiency rating (based on 300um droplet size) and a long service life, meeting the specifications set by leading manufacturers of diesel fuel injection systems, this PreLine-Plus pre-filter kit will reliably protect your fuel system from corrosion, abrasion and the frequency of repairs reduced.
WATER ALERT SYSTEM
The PreLine-Plus kit includes an intuitive multi-stage water alert that separates it from other kits on the market. The alarm will notify the driver in the event that water is detected in the fuel which also eliminates the need to manually check for water.
ALPINE S2-Series 12" Prisma Subwoofer Enclosure - S2-SB12
$539.96
$599.95
Good looks, great bass
Alpine's PrismaLink S2-Series subwoofer enclosures combine great Alpine bass with stunning visual appeal. Integrated RGB lighting bars make your system look as good as it sounds while rugged built-in S2-Series subwoofers deliver the sonic goods. The rugged MDF enclosure with carpet covering stands up to the stresses of car life, and its wedge-shaped design allows it to fit in more places.
Lighting and multi-sub options
The pre-wired dual RGB lighting bars can be controlled by the included wireless remote or through the screen of the Alpine ILX-W670 receiver (sold separately). You can link multiple S2-S12B enclosures with the optional KTX-LK12 bracket for a kaleidoscopic multi-sub system. For the final touch, a twist-lock mounting system makes it easy to add one of Alpine's specially-designed speaker grilles (sold separately).
Big bass from a 12" sub
This S2-SB12 features Alpine's S2-W12D4 subwoofer with dual 4-ohm voice coils wired for 2-ohm impedance. Its carbon fiber/polypropylene cone and HAMR multi-roll rubber surround deliver powerful bass. It handles up to 600 watts of RMS power (1800 watts peak), so you can feed it plenty of power.
READ LESS
Product highlights:
sealed enclosure with one S2 Series 12" woofer
MDF enclosure with carpet covering
carbon fiber/polypropylene cone with ceramic/polypropylene dust cap
High-Amplitude Multi-Roll (HAMR) rubber surround
integrated RGB lighting bars
linkable to additional S2-SB12 enclosures with KTX-LK12 linking kit (sold separately)
includes twist-lock surround trim ring
2-ohm total impedance
power handling: 600 watts (1800 watts peak)
frequency response: 23-215 Hz
sensitivity: 86 dB
dimensions: 16.63"W x 15"H x 13.13"D1 x 6.25"D2
warranty: 1 year
MFR # S2-SB12
Item # 500S2SB12
What's in the box:
Linkable ported enclosure loaded with one S2-W12D4 subwoofer
IR Remote control (CR2025 battery NOT included)
6" RGB wiring harness
Instruction sheet
Product registration information
Warranty information
Important notice
DIRECTION-PLUS Fuel Manager Pre-Filter Kit Volkswagen Amarok () - FM643DPK
$538.20
$598.00
Direction Plus™ Fuel Manager Pre-Filter Kit FM643DPK is designed and engineered in Australia to suit Volkswagen Amarok 6cyl models, protecting the engine against costly injector failure.
VW Amarok DDXC/XE (3.0L 6cyl) 2016 – 2023
Single Battery Only
Only one Kit can be fitted, either Fuel Manager or ProVent Catch Can
Kit will not fit if the water pump is fitted on the drivers side. Please check before purchase.
PROTECT YOUR ENGINE
It’s easy to think that fuel contamination is something that happens “in the bush” but this is simply not true!
Did you know that 72% of all diesel fuel injection system failures are caused by water and fuel lubricity problems?
Direction Plus™ Fuel Manager Pre-Filter Kits protect late model common rail diesel engines against costly injector failure.
HOW IT WORKS
Installing a Direction Plus™ Fuel Manager Pre-filter kit between the fuel tank and the O.E.M fuel filter, the Fuel Manager will remove the majority of water and particle contamination. This leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system.
For the ultimate front line defence against water and particle contamination, investing in a DirectionPlus™ Fuel Manager Pre-Filter Kit will protect your investment 24 hours a day, 365 days a year.
BENEFITS OF A FUEL MANAGER PRE-FILTER KIT:
Reduce wear & tear and avoid repair costs that can exceed $10,000
95% water separation and superior particle removal
Ability to separate emulsified water from ULSD
Clear water drainage bowl to easily identify removed water
Keeps critical engine components clean
No filter bypass – contaminated fuel will not be sent to the fuel system even when the filter is blocked
Check fitment guide below to confirm suitability for your vehicle.
FRONT RUNNER Toyota Tacoma Retrax Xr 5 (2005-Current) Double Load...
$537.30
$597.00
This dual set of Load Bars allows you to transport gear and attach Front Runner accessories above the bed of your Toyota Tacoma when there’s no need for a full-sized bed rack. This low-profile solution fits into the existing ReTrax XR rails, and doesn’t compromise any of the load bed’s regular load-carrying ability, while the drop-down door functions as usual.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Toyota Tacoma when fitted with a ReTrax XR rails. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 x 1425mm Load Bars that fit into the existing ReTrax XR rails, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
KRTT970 - Toyota Tacoma ReTrax XR 5" (2005-Current) Double Load Bar Kit - by Front RunnerConsisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK016 - Roof Load Bar Pair 1425mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 6kg (13.23lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 170mm (7")Length: 1540mm (61")Height: 160mm (6")Shipping Weight:Weight: 9kg (20lbs)
FRONT RUNNER Ford Ranger Retrax Xr 6 (2019-2022) Double Load...
$537.30
$597.00
This dual set of Load Bars allows you to transport gear and attach Front Runner accessories above the bed of your Ford Range when there’s no need for a full-sized bed rack. This low-profile solution fits into the existing ReTrax XR rails, and doesn’t compromise any of the load bed’s regular load-carrying ability, while the drop-down door functions as usual.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Ford Ranger when fitted with a ReTrax XR rails. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 x 1425mm Load Bars that fit into the existing ReTrax XR rails, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
KRFR005 - Ford Ranger ReTrax XR 6" (2019-2022) Double Load Bar Kit - by Front RunnerConsisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK016 - Roof Load Bar Pair 1425mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 6kg (13.23lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 160mm (6")Length: 1500mm (59")Height: 155mm (6")Shipping Weight:Weight: 8kg (18lbs)
FRONT RUNNER Ford Ranger Retrax Xr 5In (2019-2022) Double Load...
$537.30
$597.00
This dual set of Load Bars allows you to transport gear and attach Front Runner accessories above the bed of your Ford Ranger when there’s no need for a full-sized bed rack. This low-profile solution fits into the existing ReTrax XR rails, and doesn’t compromise any of the load bed’s regular load-carrying ability, while the drop-down door functions as usual.
A set of Pickup Bed Load Bars used to transport gear over the bed of your Ford Ranger when fitted with a ReTrax XR rails. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 x 1425mm Load Bars that fit into the existing ReTrax XR rails, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails.
Allows for gear to be mounted above the pickup’s load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
Consisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK016 - Roof Load Bar Pair 1425mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 6kg (13.23lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 160mm (6")Length: 1500mm (59")Height: 155mm (6")Shipping Weight:Weight: 8kg (18lbs)
LIGHTFORCE BEAST 230 Super Bundle — Driving Lights (pair) and...
$1,129.00
$1,352.00
LIGHTFORCE BEAST 230 3-Mode Driving Light Ultimate Bundle
Upgrade your vehicle lighting with the complete LIGHTFORCE BEAST 230 Ultimate Bundle. Designed for off-road enthusiasts, touring vehicles, and professional applications, this all-in-one kit delivers maximum visibility, durability, and ease of installation.
This bundle includes a pair of powerful BEAST 230 LED driving lights and a dedicated plug-and-play wiring harness for a complete lighting upgrade.
What’s Included
LIGHTFORCE BEAST 230 LED Driving Light - Pair (3-Mode) – BEAST230PK
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play solution with no additional parts required
3 beam modes: Spot, Flood, and BEAST for versatile driving conditions
Extended beam distance and wider spread for maximum visibility
Heavy-duty construction designed for extreme environments
Quick and easy installation with included wiring harness
BEAST 230 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
High-output LED performance for long-range and wide visibility
Optimised beam pattern for off-road and highway use
5700K colour temperature for clear, natural visibility
Large format design for increased light output and coverage
Daytime Running Light (DRL) functionality
Heavy-duty aluminium housing for durability and heat management
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Single 8-pin connector for clean installation
Includes relay, rocker switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
Impact-resistant construction for harsh environments
Operating temperature range: -40°C to 85°C
Resistant to UV, salt spray, and corrosion
Long-lasting LED lifespan
Specifications
Light Size: 230mm
Voltage: 12V system compatible
Colour Temperature: 5700K
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Rural and low-light environments
Why Choose LIGHTFORCE BEAST 230 Bundle
This bundle provides a complete, professional-grade lighting solution with industry-leading performance and durability. With advanced beam technology and simple installation, it is the ideal upgrade for drivers who demand reliability and visibility.
Order now to upgrade your driving visibility with a complete BEAST lighting setup.
LIGHTFORCE BEAST 190 Ultimate Bundle — Pair of Driving Lights...
$999.00
$1,150.00
LIGHTFORCE BEAST 190 Ultimate Bundle – 3-Mode Pair Of Driving Lights with Wiring Harness
The LIGHTFORCE BEAST 190 Ultimate Bundle is a complete high-performance lighting solution designed for off-road, touring, and demanding driving conditions. This bundle combines the powerful BEAST 190 LED driving lights with a dedicated 3-mode wiring harness for a simple, professional installation.
Engineered and manufactured in Australia, the BEAST 190 delivers exceptional beam distance, width, and durability in a compact 190mm design. With three selectable beam modes, this system allows you to adapt instantly to changing environments for maximum control and confidence.
What’s Included
2 X LIGHTFORCE BEAST 190 LED Driving Light – BEAST190X1
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play lighting solution
3 beam modes: Spot, Flood, and BEAST
Up to 1260m beam distance for long-range visibility
Compact design with extreme durability
Quick and easy installation with dedicated wiring harness
BEAST 190 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
Up to 1 lux at 1260m (pair) for long-distance performance
25 high-performance Osram LEDs
5700K colour temperature for clear, natural visibility
Compact 190mm size with ultra-slim 80mm depth
Daytime Running Light (DRL) functionality
Pressure die-cast aluminium housing for strength and heat dissipation
Beam Modes
Spot Mode: Long-distance beam up to 1195m
Flood Mode: Wide beam up to 496m
BEAST Mode: Combined distance and width up to 1260m
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Includes relay, switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
IK16 impact resistance for extreme durability
Operating temperature range from -40°C to 85°C
Resistant to UV, salt spray, and corrosion
LED lifespan up to 50,000 hours
Specifications
Diameter: 190mm
Depth: 80mm
Weight: 1.6kg
Voltage: 13.2V
Ingress Rating: IP69K
Colour Temperature: 5700K
Warranty: 5 Years
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Low-light and rural environments
Why Choose This Bundle
This bundle delivers a complete, professional-grade lighting upgrade with everything required for installation. Combining advanced LED performance, versatile beam control, and enhanced durability, it is ideal for drivers who demand reliability and maximum visibility in all conditions.
Upgrade your setup with the LIGHTFORCE BEAST 190 Ultimate Bundle today.
ALPINE LC70 Ultimate Status Audio & Camera Bundle, Speakers +...
$6,899.00
$7,700.00
ALPINE LC70 Ultimate Status Audio and Camera Bundle – Complete Premium Sound System
The ALPINE LC70 Ultimate Status Bundle is the complete high-end audio and safety upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining Alpine’s advanced i905-LC70 head unit, R2-Series speaker system, Alpine Status HDA-V90 amplifier, RS-SB10 shallow subwoofer, and rear view camera, this bundle delivers exceptional sound quality, powerful bass, and enhanced driving visibility.
Built using Alpine’s latest Hi-Res Audio technology, this system delivers a true high-resolution listening experience with precision, clarity, and depth, while maintaining seamless factory-style integration.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE HDA-V90 5-Channel Hi-Res Audio Amplifier
ALPINE RS-SB10 Shallow Subwoofer Enclosure
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete premium audio and safety system in one bundle
Hi-Res Audio performance with powerful, detailed sound
Deep, controlled bass from shallow subwoofer design
High-output 5-channel amplifier for full system control
Wireless Apple CarPlay and Android Auto connectivity
Improved reversing safety with rear view camera
Seamless integration for LandCruiser 70 Series Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier and advanced sound tuning
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for accurate sound reproduction
Glass-fibre reinforced cones for clarity and response
HAMR surround for enhanced bass performance
Integrated door pods with USB charging and storage
HDA-V90 Amplifier Features
5-channel Class-D amplifier with Hi-Res Audio certification
Frequency response: 10Hz – 60kHz
75W x 4 + 300W x 1 @ 4Ω output
100W x 4 + 500W x 1 @ 2Ω output
High damping factor for precise speaker control
Low distortion for clean and accurate sound
RS-SB10 Subwoofer Features
Shallow 12-inch high-performance subwoofer enclosure
600W RMS and 1800W peak power handling
Ultra-compact design for flexible installation
Neodymium magnet for high efficiency and power
20mm X-max for deep, controlled bass output
Rear View Camera Features
Wide viewing angle for improved rear visibility
HDR technology for clear image in low light conditions
Automatic activation when reversing
Day and night image adjustment
System Performance
High-resolution audio playback across full system
Powerful amplified output with deep bass response
Balanced sound staging with precise tuning capability
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete premium audio system
Off-road and touring vehicles
Users wanting high-performance sound and added safety
Why Choose This Bundle
This bundle represents the ultimate Alpine upgrade, combining industry-leading components into one complete system. Designed for performance, clarity, and reliability, it delivers a superior in-car experience with powerful sound, deep bass, and enhanced safety features.
Transform your LandCruiser 70 Series with Alpine’s ultimate audio and camera system.
ALPINE LC70 Premium Audio Bundle — Head Unit + Speakers
$4,499.00
$5,199.90
ALPINE LC70 Premium Audio Bundle – i905-LC70 Head Unit with R2-Series Speaker Upgrade
The ALPINE LC70 Premium Audio Bundle is the ultimate in-car sound upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 9-inch multimedia receiver with Alpine’s R2-Series door pod speaker system, this bundle delivers powerful, high-resolution audio with seamless factory-style integration.
Designed for both performance and practicality, this setup transforms your vehicle into a premium listening environment while enhancing interior functionality and aesthetics.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
Key Benefits
Complete premium audio upgrade for LandCruiser 70 Series Dual Cab
High-resolution sound with powerful bass and clarity
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration with modern design enhancement
Additional functionality with storage, USB charging, and lighting
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
Seamless integration designed for LC70 interior
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear for powerful output
Hi-Res Audio certified for accurate and detailed sound
Glass-fibre reinforced cones for fast response and clarity
HAMR surround for increased bass performance and control
Neodymium magnet structure for improved efficiency
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated front and rear speaker pods
Built-in USB charging ports (up to 4 devices)
Integrated puddle lighting for improved visibility at night
Storage compartments for bottles, maps, and accessories
Durable injection-moulded PC/ABS construction
Performance Specifications
Peak Power Handling: 300W
RMS Power Handling: 100W
Nominal Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Woofer Size: 6x9 inch
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers upgrading factory audio systems
Off-road and touring vehicles
Users seeking premium sound quality and modern connectivity
Why Choose This Bundle
This bundle delivers a complete, high-performance audio upgrade with seamless integration, powerful sound output, and added interior functionality. Designed specifically for the LC70, it combines Alpine’s industry-leading technology with practical features for everyday use and off-road adventures.
Upgrade your LandCruiser 70 Series with Alpine’s premium audio solution today.
ALPINE LC70 Ultimate Audio System Bundle — Head Unit +...
$5,099.00
$5,899.85
ALPINE LC70 Ultimate Audio System Bundle – Head Unit, Speaker Upgrade and Amplifier
The ALPINE LC70 Ultimate Audio System Bundle is a complete premium sound upgrade designed specifically for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 multimedia receiver, Alpine R2-Series speaker door pod system, and the powerful R2-A60F amplifier, this bundle delivers exceptional clarity, depth, and power.
Engineered for audiophiles and off-road enthusiasts, this system transforms your vehicle into a high-performance listening environment with seamless factory-style integration and modern connectivity.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE R2-A60F Class-D Digital Amplifier
Key Benefits
Complete premium audio system upgrade in one bundle
High-resolution sound with powerful bass and clarity
Amplified performance for maximum output and control
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration designed for LC70 Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for detailed and accurate sound
Glass-fibre reinforced cones for fast response
HAMR surround for increased bass performance
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated speaker pods front and rear
Built-in USB charging ports for up to 4 devices
Integrated puddle lighting for improved visibility
Storage compartments for everyday convenience
Durable PC/ABS construction for long-lasting use
R2-A60F Amplifier Features
Compact Class-D digital amplifier with reduced footprint
Hi-Res Audio certified up to 45kHz
Top panel sound controls for easy tuning
One-sided terminal layout for simplified installation
100W RMS x 4 @ 4Ω output
150W RMS x 2 @ 2Ω output
300W RMS x 2 @ 4Ω bridged
Frequency response: 10Hz – 45,000Hz
High damping factor for improved speaker control
Performance Specifications
Speaker Peak Power: 300W
Speaker RMS Power: 100W
Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete audio system upgrade
Off-road and touring vehicles
Users wanting powerful, high-quality sound performance
Why Choose This Bundle
This bundle delivers a complete, high-performance audio solution combining premium components for superior sound quality, power, and control. Designed specifically for the LC70, it ensures seamless integration while providing a significant upgrade over factory audio systems.
Upgrade your LandCruiser 70 Series with Alpine’s ultimate audio system bundle today.
ALPINE LC70 Premium Head Unit & Reverse Camera Bundle —...
$2,699.00
$3,099.90
ALPINE LC70 Premium Head Unit and Reverse Camera Bundle – i905-LC70 with HCE-C1100 Camera
The ALPINE LC70 Premium Bundle combines cutting-edge infotainment with enhanced driving safety, designed specifically for Toyota LandCruiser 70 Series. Featuring the advanced i905-LC70 9-inch multimedia receiver and the HCE-C1100 rear view camera, this bundle delivers seamless connectivity, high-resolution audio, and improved visibility when reversing.
Upgrade your dashboard with a modern, integrated system that enhances both your driving experience and vehicle functionality.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete infotainment and safety upgrade in one bundle
Wireless Apple CarPlay and Android Auto connectivity
High-definition 9-inch WXGA display
Enhanced reversing visibility with wide-angle camera
Seamless integration designed for LandCruiser 70 Series
i905-LC70 Head Unit Features
9-inch WXGA high-resolution display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for superior sound performance
Advanced sound tuning for custom audio control
Seamless integration with LandCruiser 70 Series interior
Rear View Camera Features
Wide viewing angle: 131° horizontal, 103° vertical
HDR technology for clear vision in low-light conditions
Automatic day and night image adjustment
RCA or direct Alpine connection compatibility
Automatic activation when reversing
Compact design with included mounting hardware
Camera Specifications
Resolution: 640 x 480
Waterproof rating: IP67
Power supply: DC5.0V – DC7.0V
Viewing angle: 131° horizontal, 103° vertical
Operating temperature: -30°C to +70°C
Designed For
Toyota LandCruiser 70 Series
Off-road and touring vehicles
Daily driving and work vehicles
Drivers seeking upgraded audio and safety
Why Choose This Bundle
This bundle delivers a complete in-car upgrade, combining premium audio performance with enhanced safety features. Designed specifically for the LandCruiser 70 Series, it ensures seamless integration, modern functionality, and improved driving confidence.
Upgrade your LandCruiser 70 Series with Alpine’s premium multimedia and camera solution today.
