FRONT RUNNER Ute Load Bed Load Bar Kit / 1475Mm(W)...
$642.60
$714.00
A set of Ute Bed Load Bars used to transport gear over the bed of your ute when there’s no need for a full Front Runner Rack. This low profile, smaller footprint solution includes 4 188mm Load Bed Legs, 2 1475mm Load Bars, 2 Ute Load Bed Tracks and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the bed of the vehicle.
A set of Pickup Bed Load Bars used to transport gear over the bed of your truck when there’s no need for a full Front Runner Rack. This low profile, smaller footprint solution includes 4 188mm Load Bed Legs, 2 1475mm Load Bars, 2 Pickup Load Bed Tracks and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the bed of the vehicle.
You may not have the need for a full sized bed rack and find that you can get by using a set of Front Runner Load Bars.The Load Bars are mounted via Load Bed Legs that bolt directly onto a set of Front Runner bed mounted tracks.Allows for gear to be mounted above the pick up’s load bay.The load bay retains its load carrying ability, while the drop down door functions as usual.Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.The Load Bars and Load Bed Legs can be used in the future as components to build a complete Front Runner Roof Rack.Made from stainless steel and a durable, weather resistant black powder-coated aluminum.Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
AM General, Giant Motors, Sang Yong, American, Motors, Chevrolet, Dodge, Ford, Foton, GMC, GWM, Holden, Hyundai, International, Isuzu, JMC, Land Rover, Mahindra, Mazda, Mercedes-Benz, Mitsubishi, Nissan, Ram, Tata, Toyota, Volkswagen
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Consisting of:
2 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner1 x LBSK017 - Roof Load Bar Pair 1475mm(W) - by Front Runner1 x TRBU001 - Pickup Load Bed Tracks / 1000mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 9kg (20lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle’s rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 130mm (5")Length 1580mm (62")Height 220mm (9")
Shipping Weight:
Weight 10.6kg (23.3lbs)
FRONT RUNNER Ram 1500/2500/3500 Retrax Xr (2003-Current) Double Load Bar...
$573.30
$637.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500/2500/3500 when fitted with a ReTrax XR rails. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 x 1575mm Load Bars that fit into the existing ReTrax XR rails, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRDR025 - Ram 1500/2500/3500 ReTrax XR (2003-Current) Double Load Bar Kit - by Front Runner
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK018 - Roof Load Bar Pair 1575mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 6.8kg (14.99lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 170mm (7")
Length: 1690mm (67")
Height: 160mm (6")
Shipping Weight:
Weight: 8kg (18lbs)
FRONT RUNNER Ram 1500 6.4' Crew Cab (2009-Current) Triple Load...
$1,016.10
$1,129.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 Crew Cab. This low profile solution includes 6 Pickup Roll Top Leg Mounts, 3 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Features
KRDR020 - Ram 1500 6.4' Crew Cab (2009-Current) Triple Load Bar Kit - by Front Runner
Consisting of:
3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner
1 x LBSK019 - Roof Load Bar Set 1575mm(W) - by Front Runner
1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 16.6kg (36.7lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 390mm (15.0")
Length: 1630mm (64.0")
Height: 130mm (5.0")
Shipping Weight:
16.4kg (36.0lbs)
FRONT RUNNER Nissan Navara (2014-Current) Egr Rolltrac Load Bed Load...
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Nissan Navara when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT009 - Nissan Navara (2014-Current) EGR RollTrac Load Bed Load Bar Kit
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 8.54kg (18.83lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1590mm (63")
Height: 160mm (6")
Shipping Weight:
Weight: 8.4kg (18lbs)
FRONT RUNNER Mitsubishi Pajero Swb (1992-1999) Load Bar Kit /...
$576.00
$640.00
A set of Load Bars with Track Mounted Feet used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 2 40mm Feet, 2 60mm Feet, 2 1165mm Load Bars, 2 Mitsubishi Pajero SWB 1620mm Tracks, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner Load Bars.
These Load Bars are mounted to the vehicles roof via a set of supplied Tracks and Track Mounted Feet.
Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.
Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.
Made from stainless steel and a durable, weather resistant black powder-coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Features
KRMP017 - Mitsubishi Pajero SWB Load Bar Kit? / Track & Feet - by Front Runner
Consisting of:
1 x FASS012 - Foot Set / 40mm-50mm - by Front Runner
1 x FASS013 - Foot Set / 60mm-70mm - by Front Runner
1 x LBSK013 - Load Bar Pair 1165mm(W) - by Front Runner
1 x TRMP005 - Mitsubishi Pajero SWB Tracks / 1620mm(L) - by Front Runner
1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 8kg (18lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 110mm (4")
Length 1625mm (64")
Height 180mm (7")
Shipping Weight:
Weight 9.4kg (20.7lbs)
FRONT RUNNER Mazda Bt50 (2012-Current) Egr Rolltrac Load Bed Load...
$569.70
$633.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Mazda BT50 when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT005 - Mazda BT50 (2012-Current) EGR RollTrac Load Bed Load Bar Kit - by Front Runner
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 8.24kg (18.17lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1590mm (63")
Height: 290mm (11")
Shipping Weight:
Weight: 8.4kg (18lbs)
FRONT RUNNER Volkswagen Touareg (2002-2010) Load Bar Kit / Feet...
$367.20
$408.00
A set of Load Bars with Feet used to transport gear on the roof of your vehicle when there’s no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 50mm Feet, 2 1255mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle.
A set of Load Bars with Feet used to transport gear on the roof of your vehicle when there’s no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 50mm Feet, 2 1255mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner Load Bars.These Load Bars are mounted to the vehicle’s roof via a set of supplied Feet.Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.Made from stainless steel and a durable, weather resistant black powder-coated aluminum.Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
FRONT RUNNER Volkswagen T5/T6 (2003-Current) W/Sca Pop Top Roof Load...
$379.80
$422.00
Pile on the adventure gear with the help of these low-profile, Volkswagen T5/T6 Load Bars. Added bonus? These bad boys can be used in the future as part of a complete Front Runner Roof Rack.
A set of Load Bars used to transport gear on the roof of your Volkswagen T5/T6 (2003-Current) w/SCA Pop Top Roof. This low profile solution includes 4 mounting Feet that fit into OEM SCA Pop Top rails, 2 1345mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions.
These Load Bars are mounted to the Volkswagen T5/T6 w/SCA Pop Top Roof via a set of supplied Mounted Feet.
This system installs easily with off-road tough feet that grip onto the existing factory/OEM SCA Pop Top rails. No drilling required.
Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.
Made from stainless steel and a durable, weather resistant black powder-coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
KRVK009 - Volkswagen T5/T6 (2003-Current) w/SCA Pop Top Roof Load Bar Kit
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK015 - Roof Load Bar Pair 1345mm(W)2x RRAC940 - Merc Bens Sprinter Slimpro Van Track T-Bolt Kit1x WDLB001 - Load Bar Wind Deflector / 10mm
Material Used:Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 5.61kg (12.37lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 110mm (4")Length: 1475mm (58")Height: 150mm (6")
Shipping Weight:Weight: 6.2kg (14lbs)
FRONT RUNNER Slimline Ii Roof Rack Kit Fits Toyota 4Runner...
$1,741.50
$1,935.00
This 1762mm/69.4" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Toyota 4Runner (4th Gen). It easily installs using the existing factory mounting points. No drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables.
These Foot Rails contain 1 opening to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit).
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRTF051T - Toyota 4Runner (4th Gen) Slimline II Roof Rack Kit - by Front Runner
Consisting of:
1 x FATF003 - Toyota 4runner (2002-2008) Foot Rails - by Front Runner
1 x RRSTD09 - Slimline II Tray - 1255mm(W) X 1762mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 30kg (65lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 140mm (6")
Shipping Weight:
Weight 34.4kg (75.7lbs)
FRONT RUNNER Ute Roll Top Slimline Ii Load Bed Rack...
$1,537.20
$1,708.00
This kit creates a full-size rack that sits above your Pickup Truck's load bed when fitted with a Roll Top Cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1425mm x 1358mm) and 4 Pickup Roll Top Leg Mounts that fit into the existing factory/OEM tracks in your Roll Top Cover.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT001T - Bakkie Roll Top Slimline II Load Bed Rack Kit / 1425(W) x 1358(L) - by Front Runner
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 27.05kg (59.63lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 455mm (18"); Length: 1610mm (63"); Height: 235mm (9")
Shipping Weight:
Weight: 27.82kg (61lbs)
FRONT RUNNER Slimline Ii Roof Rack Kit Fits Toyota Condor...
$1,766.70
$1,963.00
This 1762mm/69.4" long full-size Slimline II cargo carrying roof rack kit for the Toyota Condor contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRTC001L - Toyota Condor Slimline II Roof Rack Kit - by Front Runner
Consisting of:
2 x LASS105 - No 5 Leg 190mm (Pair) - by Front Runner
1 x LASS106 - No 6 Leg 195mm (Pair) - by Front Runner
1 x RRSTD09 - Slimline II Tray - 1255mm(W) X 1762mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 28kg (62lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 140mm (6")
Shipping Weight:
Weight 32.9kg (72.4lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,458.90
$1,621.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to six (6) supplied Feet that slide in to the supplied Track. The 1400mm/55.1" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA001T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 1358mm(L) - by Front RunnerConsisting of:3x FASS024 - Foot Set / 50mm - 60mm1x RRSTA07 - SLII Tray - 1165mm(W)X1358mm(L)1x TRAC002 - Universal Track / 1400mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 25.89kg (57.08lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 445mm (18")Length: 1730mm (68")Height: 265mm (10")Shipping Weight:Weight: 29kg (64lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,072.80
$1,192.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1156mm/45.5" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA004TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1156mm(L) - by Front Runner
Consisting of
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA06 - Slimline II Tray - 1165mm(W) X 1156mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 18kg (39lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 20.7kg (45.6lbs)
FRONT RUNNER Canopy Load Bar Kit / 1165Mm (W) -...
$495.00
$550.00
A set of Load Bars with Track Mounted Feet used to transport gear on the roof of your vehicle when there’s no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 40mm Feet, 2 1165mm Load Bars, 2 1150mm Canopy Tracks, and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner Load Bars.These Load Bars are mounted to the vehicle’s roof via a set of supplied Tracks and Track Mounted Feet.Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.Made from stainless steel and a durable, weather resistant black powder-coated aluminum.Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA007 - Canopy Load Bar Kit / 1165mm (W) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x LBSK013 - Load Bar Pair 1165mm(W) - by Front Runner1 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 7kg (14lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle’s rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions:
Width 245mm (10")Length 1290mm (51")Height 115mm (5")
Shipping Weight:
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,233.90
$1,371.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1156mm/45.5" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 1150mm/45.3" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA004T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 1156mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA06 - Slimline II Tray - 1165mm(W) X 1156mm(L) - by Front Runner1 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 20kg (43lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot, Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 22.9kg (50.4lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,261.80
$1,402.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA005TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1358mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 20kg (44lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 23.1kg (50.9lbs)
FRONT RUNNER Canopy Load Bar Kit / 1345Mm - KRCA010
$360.90
$401.00
The Canopy Load Bar Kit was made for travelers who need additional canopy storage capacity, but don’t want to sacrifice a low-profile build. These 1345mm bars use the same durable aluminum slats as the Slimline II Roof Rack, allowing you to mount Front Runner accessories.
Comes with all hardware and components needed to fit load bars on a vehicle, including four (4) mounting feet, two (2) 1345mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA0010 - Canopy Load Bar Kit / 1345mm - by Front Runner
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK015 - Roof Load Bar Pair 1345mm(W)
Material Used:Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 6kg (13.23lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 110mm (4")Length: 1455mm (58")Height: 135mm (6")
Shipping Weight:Weight: 5.18kg (11.42lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,357.20
$1,508.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1560mm/61.4" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA001TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1560mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA08 - Slimline II Tray - 1165mm(W) X 1560mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 21kg (47lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")Shipping Weight:
Weight 25.0kg (55.0lbs)
FRONT RUNNER Rsi Double Cab Smart Canopy Slimline Ii Rack...
$1,286.10
$1,429.00
This kit creates a full size rack on a RSI Canopy with a roof top size of approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to supplied Feet that slide in to the canopy track.
This kit creates a full size rack on a RSI Canopy with a roof top size of approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to supplied Feet that slide in to the canopy track.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*Note: This Kit does not fit Volkswagen Amarok Double Cab Canopies. Please use .
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA008T - RSI Double Cab Smart Canopy Slimline II Rack Kit / 1165mm(W) x 1358mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner3 x RRAC921 - Canopy Rack Kit Installation Set1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner
Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steel
Approximate Installed Weight: 23.3kg (51.4lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 450mm (18.0")Length: 1615mm (64.0")Height: 140mm (6.0")
Shipping Weight:23.1kg (51.0lbs)
FRONT RUNNER Canopy Load Bar Kit / 1475Mm - KRCA011
$378.90
$421.00
The Canopy Load Bar Kit was made for travelers who need additional canopy storage capacity, but don’t want to sacrifice a low-profile build. These 1475mm bars use the same durable aluminum slats as the Slimline II Roof Rack, allowing you to mount Front Runner accessories.
Comes with all hardware and components needed to fit load bars on a vehicle, including four (4) mounting feet, two (2) 1475mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA0011 - Canopy Load Bar Kit / 1475mm - by Front Runner
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material Used:Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 6kg (13.23lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 110mm (4")Length: 1585mm (63")Height: 135mm (6")
Shipping Weight:Weight: 5.6kg (12lbs)
LIGHTFORCE BEAST 230 Super Bundle — Driving Lights (pair) and...
$1,129.00
$1,352.00
LIGHTFORCE BEAST 230 3-Mode Driving Light Ultimate Bundle
Upgrade your vehicle lighting with the complete LIGHTFORCE BEAST 230 Ultimate Bundle. Designed for off-road enthusiasts, touring vehicles, and professional applications, this all-in-one kit delivers maximum visibility, durability, and ease of installation.
This bundle includes a pair of powerful BEAST 230 LED driving lights and a dedicated plug-and-play wiring harness for a complete lighting upgrade.
What’s Included
LIGHTFORCE BEAST 230 LED Driving Light - Pair (3-Mode) – BEAST230PK
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play solution with no additional parts required
3 beam modes: Spot, Flood, and BEAST for versatile driving conditions
Extended beam distance and wider spread for maximum visibility
Heavy-duty construction designed for extreme environments
Quick and easy installation with included wiring harness
BEAST 230 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
High-output LED performance for long-range and wide visibility
Optimised beam pattern for off-road and highway use
5700K colour temperature for clear, natural visibility
Large format design for increased light output and coverage
Daytime Running Light (DRL) functionality
Heavy-duty aluminium housing for durability and heat management
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Single 8-pin connector for clean installation
Includes relay, rocker switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
Impact-resistant construction for harsh environments
Operating temperature range: -40°C to 85°C
Resistant to UV, salt spray, and corrosion
Long-lasting LED lifespan
Specifications
Light Size: 230mm
Voltage: 12V system compatible
Colour Temperature: 5700K
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Rural and low-light environments
Why Choose LIGHTFORCE BEAST 230 Bundle
This bundle provides a complete, professional-grade lighting solution with industry-leading performance and durability. With advanced beam technology and simple installation, it is the ideal upgrade for drivers who demand reliability and visibility.
Order now to upgrade your driving visibility with a complete BEAST lighting setup.
LIGHTFORCE BEAST 190 Ultimate Bundle — Pair of Driving Lights...
$999.00
$1,150.00
LIGHTFORCE BEAST 190 Ultimate Bundle – 3-Mode Pair Of Driving Lights with Wiring Harness
The LIGHTFORCE BEAST 190 Ultimate Bundle is a complete high-performance lighting solution designed for off-road, touring, and demanding driving conditions. This bundle combines the powerful BEAST 190 LED driving lights with a dedicated 3-mode wiring harness for a simple, professional installation.
Engineered and manufactured in Australia, the BEAST 190 delivers exceptional beam distance, width, and durability in a compact 190mm design. With three selectable beam modes, this system allows you to adapt instantly to changing environments for maximum control and confidence.
What’s Included
2 X LIGHTFORCE BEAST 190 LED Driving Light – BEAST190X1
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play lighting solution
3 beam modes: Spot, Flood, and BEAST
Up to 1260m beam distance for long-range visibility
Compact design with extreme durability
Quick and easy installation with dedicated wiring harness
BEAST 190 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
Up to 1 lux at 1260m (pair) for long-distance performance
25 high-performance Osram LEDs
5700K colour temperature for clear, natural visibility
Compact 190mm size with ultra-slim 80mm depth
Daytime Running Light (DRL) functionality
Pressure die-cast aluminium housing for strength and heat dissipation
Beam Modes
Spot Mode: Long-distance beam up to 1195m
Flood Mode: Wide beam up to 496m
BEAST Mode: Combined distance and width up to 1260m
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Includes relay, switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
IK16 impact resistance for extreme durability
Operating temperature range from -40°C to 85°C
Resistant to UV, salt spray, and corrosion
LED lifespan up to 50,000 hours
Specifications
Diameter: 190mm
Depth: 80mm
Weight: 1.6kg
Voltage: 13.2V
Ingress Rating: IP69K
Colour Temperature: 5700K
Warranty: 5 Years
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Low-light and rural environments
Why Choose This Bundle
This bundle delivers a complete, professional-grade lighting upgrade with everything required for installation. Combining advanced LED performance, versatile beam control, and enhanced durability, it is ideal for drivers who demand reliability and maximum visibility in all conditions.
Upgrade your setup with the LIGHTFORCE BEAST 190 Ultimate Bundle today.
ALPINE LC70 Ultimate Status Audio & Camera Bundle, Speakers +...
$6,160.00
$7,700.00
ALPINE LC70 Ultimate Status Audio and Camera Bundle – Complete Premium Sound System
The ALPINE LC70 Ultimate Status Bundle is the complete high-end audio and safety upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining Alpine’s advanced i905-LC70 head unit, R2-Series speaker system, Alpine Status HDA-V90 amplifier, RS-SB10 shallow subwoofer, and rear view camera, this bundle delivers exceptional sound quality, powerful bass, and enhanced driving visibility.
Built using Alpine’s latest Hi-Res Audio technology, this system delivers a true high-resolution listening experience with precision, clarity, and depth, while maintaining seamless factory-style integration.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE HDA-V90 5-Channel Hi-Res Audio Amplifier
ALPINE RS-SB10 Shallow Subwoofer Enclosure
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete premium audio and safety system in one bundle
Hi-Res Audio performance with powerful, detailed sound
Deep, controlled bass from shallow subwoofer design
High-output 5-channel amplifier for full system control
Wireless Apple CarPlay and Android Auto connectivity
Improved reversing safety with rear view camera
Seamless integration for LandCruiser 70 Series Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier and advanced sound tuning
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for accurate sound reproduction
Glass-fibre reinforced cones for clarity and response
HAMR surround for enhanced bass performance
Integrated door pods with USB charging and storage
HDA-V90 Amplifier Features
5-channel Class-D amplifier with Hi-Res Audio certification
Frequency response: 10Hz – 60kHz
75W x 4 + 300W x 1 @ 4Ω output
100W x 4 + 500W x 1 @ 2Ω output
High damping factor for precise speaker control
Low distortion for clean and accurate sound
RS-SB10 Subwoofer Features
Shallow 12-inch high-performance subwoofer enclosure
600W RMS and 1800W peak power handling
Ultra-compact design for flexible installation
Neodymium magnet for high efficiency and power
20mm X-max for deep, controlled bass output
Rear View Camera Features
Wide viewing angle for improved rear visibility
HDR technology for clear image in low light conditions
Automatic activation when reversing
Day and night image adjustment
System Performance
High-resolution audio playback across full system
Powerful amplified output with deep bass response
Balanced sound staging with precise tuning capability
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete premium audio system
Off-road and touring vehicles
Users wanting high-performance sound and added safety
Why Choose This Bundle
This bundle represents the ultimate Alpine upgrade, combining industry-leading components into one complete system. Designed for performance, clarity, and reliability, it delivers a superior in-car experience with powerful sound, deep bass, and enhanced safety features.
Transform your LandCruiser 70 Series with Alpine’s ultimate audio and camera system.
ALPINE LC70 Premium Audio Bundle — Head Unit + Speakers
$4,159.92
$5,199.90
ALPINE LC70 Premium Audio Bundle – i905-LC70 Head Unit with R2-Series Speaker Upgrade
The ALPINE LC70 Premium Audio Bundle is the ultimate in-car sound upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 9-inch multimedia receiver with Alpine’s R2-Series door pod speaker system, this bundle delivers powerful, high-resolution audio with seamless factory-style integration.
Designed for both performance and practicality, this setup transforms your vehicle into a premium listening environment while enhancing interior functionality and aesthetics.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
Key Benefits
Complete premium audio upgrade for LandCruiser 70 Series Dual Cab
High-resolution sound with powerful bass and clarity
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration with modern design enhancement
Additional functionality with storage, USB charging, and lighting
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
Seamless integration designed for LC70 interior
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear for powerful output
Hi-Res Audio certified for accurate and detailed sound
Glass-fibre reinforced cones for fast response and clarity
HAMR surround for increased bass performance and control
Neodymium magnet structure for improved efficiency
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated front and rear speaker pods
Built-in USB charging ports (up to 4 devices)
Integrated puddle lighting for improved visibility at night
Storage compartments for bottles, maps, and accessories
Durable injection-moulded PC/ABS construction
Performance Specifications
Peak Power Handling: 300W
RMS Power Handling: 100W
Nominal Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Woofer Size: 6x9 inch
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers upgrading factory audio systems
Off-road and touring vehicles
Users seeking premium sound quality and modern connectivity
Why Choose This Bundle
This bundle delivers a complete, high-performance audio upgrade with seamless integration, powerful sound output, and added interior functionality. Designed specifically for the LC70, it combines Alpine’s industry-leading technology with practical features for everyday use and off-road adventures.
Upgrade your LandCruiser 70 Series with Alpine’s premium audio solution today.
ALPINE LC70 Ultimate Audio System Bundle — Head Unit +...
$4,719.88
$5,899.85
ALPINE LC70 Ultimate Audio System Bundle – Head Unit, Speaker Upgrade and Amplifier
The ALPINE LC70 Ultimate Audio System Bundle is a complete premium sound upgrade designed specifically for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 multimedia receiver, Alpine R2-Series speaker door pod system, and the powerful R2-A60F amplifier, this bundle delivers exceptional clarity, depth, and power.
Engineered for audiophiles and off-road enthusiasts, this system transforms your vehicle into a high-performance listening environment with seamless factory-style integration and modern connectivity.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE R2-A60F Class-D Digital Amplifier
Key Benefits
Complete premium audio system upgrade in one bundle
High-resolution sound with powerful bass and clarity
Amplified performance for maximum output and control
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration designed for LC70 Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for detailed and accurate sound
Glass-fibre reinforced cones for fast response
HAMR surround for increased bass performance
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated speaker pods front and rear
Built-in USB charging ports for up to 4 devices
Integrated puddle lighting for improved visibility
Storage compartments for everyday convenience
Durable PC/ABS construction for long-lasting use
R2-A60F Amplifier Features
Compact Class-D digital amplifier with reduced footprint
Hi-Res Audio certified up to 45kHz
Top panel sound controls for easy tuning
One-sided terminal layout for simplified installation
100W RMS x 4 @ 4Ω output
150W RMS x 2 @ 2Ω output
300W RMS x 2 @ 4Ω bridged
Frequency response: 10Hz – 45,000Hz
High damping factor for improved speaker control
Performance Specifications
Speaker Peak Power: 300W
Speaker RMS Power: 100W
Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete audio system upgrade
Off-road and touring vehicles
Users wanting powerful, high-quality sound performance
Why Choose This Bundle
This bundle delivers a complete, high-performance audio solution combining premium components for superior sound quality, power, and control. Designed specifically for the LC70, it ensures seamless integration while providing a significant upgrade over factory audio systems.
Upgrade your LandCruiser 70 Series with Alpine’s ultimate audio system bundle today.
ALPINE LC70 Premium Head Unit & Reverse Camera Bundle —...
$2,479.92
$3,099.90
ALPINE LC70 Premium Head Unit and Reverse Camera Bundle – i905-LC70 with HCE-C1100 Camera
The ALPINE LC70 Premium Bundle combines cutting-edge infotainment with enhanced driving safety, designed specifically for Toyota LandCruiser 70 Series. Featuring the advanced i905-LC70 9-inch multimedia receiver and the HCE-C1100 rear view camera, this bundle delivers seamless connectivity, high-resolution audio, and improved visibility when reversing.
Upgrade your dashboard with a modern, integrated system that enhances both your driving experience and vehicle functionality.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete infotainment and safety upgrade in one bundle
Wireless Apple CarPlay and Android Auto connectivity
High-definition 9-inch WXGA display
Enhanced reversing visibility with wide-angle camera
Seamless integration designed for LandCruiser 70 Series
i905-LC70 Head Unit Features
9-inch WXGA high-resolution display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for superior sound performance
Advanced sound tuning for custom audio control
Seamless integration with LandCruiser 70 Series interior
Rear View Camera Features
Wide viewing angle: 131° horizontal, 103° vertical
HDR technology for clear vision in low-light conditions
Automatic day and night image adjustment
RCA or direct Alpine connection compatibility
Automatic activation when reversing
Compact design with included mounting hardware
Camera Specifications
Resolution: 640 x 480
Waterproof rating: IP67
Power supply: DC5.0V – DC7.0V
Viewing angle: 131° horizontal, 103° vertical
Operating temperature: -30°C to +70°C
Designed For
Toyota LandCruiser 70 Series
Off-road and touring vehicles
Daily driving and work vehicles
Drivers seeking upgraded audio and safety
Why Choose This Bundle
This bundle delivers a complete in-car upgrade, combining premium audio performance with enhanced safety features. Designed specifically for the LandCruiser 70 Series, it ensures seamless integration, modern functionality, and improved driving confidence.
Upgrade your LandCruiser 70 Series with Alpine’s premium multimedia and camera solution today.
