FOCAL BAMXXXL Acoustic Absorption & Sound-dampening Material (Bulk Pack | 0.5mx6m) Soundproof your car Attenuates the speaker back wave Increases the bass level in your car Increases the soundproofing of outside noise This acoustic insulation kit is completing and essential to a quality car audio installation. From its use depends on optimum acoustic rendering of speakers, amplifiers and installed accessories. Technical materials made of honeycombed damping material, an Aluminum sheet and a viscoelastic complex (Butyl). Honeycombed damping material Just like the acoustic foam inside a loudspeaker, the honeycombed damping material attenuates the speaker back wave and thus increases the speaker performance. Aluminium sheet Aluminium provides rigidity to the Butyl/foam couple. This rigidity also permits the easy laying of BAM in difficult locations. Viscoelastic complex Self-adhesive, the Butyl complex absorbs the vibrations of the surface with which it’s in contact. It highly attenuates the outside noise that gets inside the car.

FOCAL BAMXL Acoustic Absorption & Sound-dampening Material (Bulk Pack | 0.5mx2m) Honeycombed damping material Just like the acoustic foam inside a loudspeaker, the honeycombed damping material attenuates the speaker back wave and then increases the speaker performance. Aluminum sheet essential component to the sandwich effect realization. This process permits to increase the performance of the viscoelastic complex. Viscoelastic complex Self-adhesive, the butyl complex absorbs the vibrations of the surface with which it’s in contact. It highly attenuates the outside noise that gets inside the car. Less noise means more music. Content: 50 x 200cm sheet

ICBMW100L BMW Upgrade 2-Way Coaxial Speaker Kit 2-WAY COAXIAL SPEAKER KIT IC BMW 100L is designed for drivers who want to replace their original audio system with a quality sound solution adapted to their vehicle. This kit is equipped with the neodymium engine and the Aluminium/Magnesium inverted dome tweeter, exclusive Focal technologies for high power handling and perfectly rendered trebles. IC BMW 100L KEY POINTS Quick installation No wire to cut, no modification 100% compatible with your vehicle Sound quality superior compared to the original one Mounting accessories included (ICBMW100L)

The Focal Inside I IW FORD Y-ISO HARNESS V2 car radio adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Ford original car radio and of Focal Inside extension cables. Designed specifically for your vehicle Quick and easy Plug and Play installation Direct link from the amplifier to your original car radio Connection to the extension cable via ISO connectors No soldering required Length: 1 foot (0.3m) Global vehicle compatibility : Ford vehicles from 2005 to 2021

FITS TOYOTA HILUX 2020-2023 Bundle Includes: Amplifier: Impulse 4.320 Power 2×55 Watts RMS to Front Speakers, 1×160 Watts RMS to Subwoofer Cables: IW IMP 2.1, IW TOY Y ISO 2020-2023 Front: IS TOY 165 Splits or *IS TOY 165 TWU if no factory tweeter podsRear: IC TOY 165 Coaxial Sub:Subwoofer: PSB 200 8inch Subwoofer Mounted in Sealed EnclosureAmplifier: Impulse4.320 Power 2x55WattsRMS to Front Speakers, 1x160WattsRMS to SubwooferCables: IW IMP 2.1, IW TOY Y ISO 2006-2019 or IW TOY V2 Y ISO 2020-2023   AMPLIFIER: Give your head unit a breath of fresh air. Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. It will give your installation a boost without you having to embark on a difficult installation process.   HARNESSES: The Focal Inside TOYOTA Y-ISO HARNESS head unit adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Toyota original head unit and of Focal Inside extension cables. AND: Compatible with the IMPULSE 4.320 compact 4-channel digital amplifier, the IMP EXTENSION I/O 150 extension cables with Plug & Play connections offer total installation freedom as they can connect each amplifier channel to one of the speaker drivers. Input/output extension: ‘Input’ to send the audio signal from the main unit to the amplifier and ‘output’ to send the signal leaving the amplifier to the original audio system.   

Designed and developed in France, the Sub 12 benefits from Focal’s sound savoir-faire. With its 12” (30cm) polypropylene cone, this subwoofer provides an excellent bass boost for any on-board audio system. It has a single voice coil architecture for simplicity and efficacy. Key points• A deep and powerful bass• Effective as bass-reflex or sealed box• Sealed box from 15L• Bass-reflex box from 30L• Robust design; steel chassis• Excellent power handling

Designed and developed in France, the Sub 10 benefits from Focal’s sound savoir-faire. With its 10” (25 cm) polypropylene cone, this subwoofer provides an excellent bass boost for any on-board audio system. It has a single voice coil architecture for simplicity and efficacy. Key points• A deep and powerful bass• Effective as bass-reflex or sealed box• Sealed box from 10L• Bass-reflex box from 25L• Robust design; steel chassis• Excellent power handling

SUB 30A4 Description The Access 30 A4 subwoofer is a great addition to your car audio installation, it gives your system heightened dynamics and you benefit from powerful Focal sound. It is ideal for use in sealed and bass reflex enclosures. Suggested Enclosures ‚Ä¢ Compact sealed enclosure: 20-30L (0.70 – 1.05 cu.ft)‚Ä¢ Bass reflex enclosure: 25-35L (0.88 – 1.23 cu.ft) SUB 30A4 Features DFS¬Æ cone (Dual Fiberglass Structure) Powerful 43/4″ (120 mm) magnet: 250 Watts RMS Spider decompression ventilated coil Great dynamics High power

10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level. Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label General Specifications Continuous Power Handling (RMS) 1500 W Recommended Amplifier Power (RMS) 500 - 1500 W Nominal Impedance (Znom) Dual 1.5 Ω Physical Specifications Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14 in / 356 mm Mounting Hole Diameter (B) 11.9 in / 302 mm Bolt Hole Circle Diameter (C) 12.7 in / 323 mm Motor Outer Diameter (D) 8.38 in / 213 mm Mounting Depth (E) 10.5 in / 267 mm Driver Displacement 0.21 cu ft / 5.9 L Net Weight 52 lb / 23.6 kg Parameters Free Air Resonance (Fs) 23.5 Hz Electrical “Q” (Qes) 0.476 Mechanical “Q” (Qms) 7.517 Total Speaker “Q” (Qts) 0.448 Equivalent Compliance (Vas) 3.68 cu ft / 104.3 L One-Way Linear Excursion (Xmax)* 1.25 in / 32 mm Reference Efficiency (no) 0.27% Efficiency (1 W / 1 m)** 86.3 dB SPL Effective Piston Area (Sd) 107.35 sq in / 0.0693 sq m DC Resistance (Re)*** 2.41 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 1.875 cu ft / 53.1 L External Width (W) 16 in / 407 mm External Height (H) 16 in / 407 mm External Depth (D) 18.875 in / 479 mm F3 37.4 Hz Fc 40.5 Hz Qtc 0.77 Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 2.375 cu ft / 67.3 L External Width (W) 25.875 in / 657 mm External Height (H) 16 in / 406 mm External Depth (D) 17.25 in / 438 mm Internal Slot Port Width (SW) 2.25 in / 57 mm Internal Slot Port Height (SH) 14.5 in / 368 mm Internal Slot Port Length (SL) 26.25 in / 667 mm Port Extension Length (EL) 7.875 in / 200 mm Tuning Frequency (Fb) 34.6 Hz F3 30.3 Hz Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 2 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-2 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.55 Hz Electrical “Q” (Qes) 0.554 Mechanical “Q” (Qms) 8.731 Total Speaker “Q” (Qts) 0.521 Equivalent Compliance (Vas) 2.544 cu ft / 72.04 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.23% Efficiency (1 W / 1 m)** 85.9 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 2.210 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 38.99 Hz Fc 48.39 Hz Qtc 0.9496 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

The Focal Inside I IW MBZ Y-ISO HARNESS car radio adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Mercedes original car radio and of Focal Inside extension cables. Designed specifically for your vehicle Quick and easy Plug and Play installation Direct link from the amplifier to your original car radio Connection to the extension cable via ISO connectors No soldering required Length: 1 foot (0.3m) Global vehicle compatibility : E-class from 2016, S-class from 2013, C-class from 2014 until 2019

W1v3 12-inch Subwoofer (300 W, 4 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.21 Hz Electrical “Q” (Qes) 0.535 Mechanical “Q” (Qms) 8.2 Total Speaker “Q” (Qts) 0.502 Equivalent Compliance (Vas) 2.706 cu ft / 76.63 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.25% Efficiency (1 W / 1 m)** 86.1 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 3.915 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 39.63 Hz Fc 48.75 Hz Qtc 0.9338 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31.41 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 10-inch Subwoofer (300 W, 4 Ω)   The 10W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (4.6 in. / 117 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 10-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary.  Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 10W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 0.55 cu. ft. (15.57 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.92 in / 125 mm Mounting Depth (E) 4.6 in / 117 mm Driver Displacement 0.037 cu ft / 1.05 L Net Weight 9.9 lb / 4.5 kg Parameters Free Air Resonance (Fs) 26.15 Hz Electrical “Q” (Qes) 0.475 Mechanical “Q” (Qms) 7.243 Total Speaker “Q” (Qts) 0.446 Equivalent Compliance (Vas) 1.533 cu ft / 43.41 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.16% Efficiency (1 W / 1 m)** 84.2 dB SPL Effective Piston Area (Sd) 53.584 sq in / 0.0346 sq m DC Resistance (Re) 3.902 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 16.5 in / 419 mm External Height (H) 13.5 in / 343 mm External Depth (D) 7 in / 178 mm F3 43.1 Hz Fc 50.9 Hz Qtc 0.868 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.9 cu ft / 25.5 L External Width (W) 17.0 in / 432 mm External Height (H) 11.5 in / 292 mm External Depth (D) 15.25 in / 387 mm Internal Slot Port Width (SW) 1.125 in / 28.6 mm Internal Slot Port Height (SH) 10.0 in / 254 mm Internal Slot Port Length (SL) 30.1875 in / 767 mm Port Extension Length (EL) 12.50 in / 318 mm Tuning Frequency (Fb) 32.17 Hz F3 31.92 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 8-inch Subwoofer (150 W, 4 Ω) The 8W1v3 is an outstanding choice when space is very tight and amplifier power is moderate. It features shallow mounting depth (3.86 in. / 98 mm) and a compact motor structure, allowing it to comfortably fit in a lot of spaces where a typical 8-inch driver will not. Lacking a pole vent, the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 8W1v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a compact 0.350 cu. ft. (9.90 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 8.0 in / 200 mm Overall Diameter (A) 8.5 in / 216 mm Mounting Hole Diameter (B) 7.09 in / 180 mm Bolt Hole Circle Diameter (C) 7.85 in / 199 mm Motor Outer Diameter (D) 4.72 in / 120 mm Mounting Depth (E) 3.86 in / 98 mm Driver Displacement 0.018 cu ft / 0.51 L Net Weight 7.4 lb / 3.4 kg Parameters Free Air Resonance (Fs) 35.40 Hz Electrical “Q” (Qes) 0.451 Mechanical “Q” (Qms) 5.791 Total Speaker “Q” (Qts) 0.418 Equivalent Compliance (Vas) 0.68 cu ft / 19.26 L One-Way Linear Excursion (Xmax)* 0.3 in / 8 mm Reference Efficiency (no) 0.18% Efficiency (1 W / 1 m)** 84.8 dB SPL Effective Piston Area (Sd) 32.67 sq in / 0.0211 sq m DC Resistance (Re) 4.06 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.350 cu ft / 9.90 L External Width (W) 12 in / 305 mm External Height (H) 10 in / 254 mm External Depth (D) 8.625 in / 219 mm F3 59.9 Hz Fc 60.7 Hz Qtc 0.717 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.50 cu ft / 14.2 L External Width (W) 13.0 in / 330 mm External Height (H) 10 in / 254 mm External Depth (D) 11.125 in / 283 mm Internal Port Diameter (ID) 2 in / 51 mm Port Length (L) 10 in / 254 mm Tuning Frequency (Fb) 38 Hz F3 39.10 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

2-Way Component System: 6.5-inch (165 mm) Woofer, 1-inch (25 mm) Silk Dome Tweeter The C1-650se component system is engineered to deliver remarkable fidelity and outstanding value in a format that easily fits in factory locations. Outfitted with pure, silk dome tweeters, the C1-650se component system stands above others in its category with silky smooth, high-frequency clarity and definition. The 1-inch tweeter’s edge-driven design delivers excellent off-axis response and treble extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. Outboard, 3rd order, high-pass in-line filters, with Advanced Tweeter Protection Circuitry, are also included to guard against high-distortion damage and improve power handling. For maximum installation versatility, surface and flush tweeter mounts are also included.  C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low-distortion sound. At the core of the C1-650 woofer is a proprietary, stamped, steel 6.5-inch (165 mm) frame and DMA-optimized motor system. A mineral-filled, injection-molded, polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil's motion. Tinsel leads are carefully routed and attached to each spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. To maximize fit, multi-application adaptor rings are included for the woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many "6-inch" speaker locations as well.  When it comes to value, C1-650se is a real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 50 W Recommended Amplifier Power (RMS) 10 - 75 W / Ch. System Efficiency 91.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 21 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.25 in / 159 mm Grille Tray Outer Diameter (B) 6.84 in / 174 mm Motor Outer Diameter (C) 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion** (E) N/A Mounting Hole Diameter (F) 5.02 in / 128 mm Mounting Depth (G) 2.07 in / 53 mm *Does not take into account mounting tabs**Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 1.97 in / 50 mm Surface Mount Fixture Diameter (A2) 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B) 1.75 in / 45 mm Flush Mount Mounting Depth (C) 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 0.87 in / 22 mm

Coaxial Speaker System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 91.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion** (D) 0.41 in / 10 mm Frontal Grille Protrusion (E) N/A Mounting Hole Diameter (F) N/A Mounting Depth (G) 2.75 in / 70 mm *Does not take into account mounting tabs**Frontal coaxial tweeter protrusion measured from mounting surface

Harness IW-SPK-SIM simulates 4 ohm speaker load as required by various headunits.

Harness IW-SPK-SIM simulates 4 ohm speaker load as required by various headunits.

SPECIFICATIONSContinuous Power Handling (RMS): 600 WRecommended Amplifier Power (RMS): 250 - 600 WNominal Impedance (Znom): 2 ΩNominal Diameter: 13.5 in / 345 mmOverall Diameter (A) A1: 14.2 in / 361mmA2: 13.0 in / 330 mmMounting Hole Diameter (B): 12.5 in / 318 mmBolt Hole Circle Diameter (C): 13.5 in / 343 mmMotor Outer Diameter (D): 6.75 in / 171 mmMounting Depth (E): 2.625 in / 67 mmDriver Displacement: 0.052 cu ft / 1.47 LNet Weight: 20.5 lb / 9.3 kgPARAMETERSFree Air Resonance (Fs): 25.95 HzElectrical “Q” (Qes): 0.51Mechanical “Q” (Qms): 10.648Total Speaker “Q” (Qts): 0.479Equivalent Compliance (Vas): 2.26 cu ft / 64.00 LOne-Way Linear Excursion (Xmax)*: 0.433 in / 11 mmReference Efficiency (no): 0.23%Efficiency (1 W / 1 m)**: 85.51 dB SPLEffective Piston Area (Sd): 98.26 sq in / 0.0634 sq mDC Resistance (Re): 2.100 Ω* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690 are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, 1-inch aluminium dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 39 Hz – 22 KHz ± 3 dB WOOFER PHYSICAL SPECIFICATIONS: Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 2.75 in / 70 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from the mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.97 in / 50 mm Surface Mount Fixture Diameter (A2): 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B): 1.75 in / 45 mm Flush Mount Mounting Depth (C): 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.87 in / 22 mm CROSSOVER PHYSICAL SPECIFICATIONS: Depth (D): 1.34 in / 34 mm Height (H): 0.90 in / 23 mm Width (W): 1.96 in / 50 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many “6-inch” speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 91.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 59 Hz – 22 kHz ± 3 dB Frame Outer Diameter* (A): 6.5 in / 165 mm Grille Tray Outer Diameter (B): 6.84 in / 174 mm Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion** (E): 0.85 in / 22 mm Mounting Hole Diameter (F): 5.56 in / 141 mm Mounting Depth (G): 2.44 in / 62 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.87 in / 48 mm Surface Mount Fixture Diameter (A2): 1.69 in / 43 mm Flush Mount Mounting Hole Diameter (B): 1.625 in / 41 mm Flush Mount Mounting Depth (C): 0.76 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.29 in / 7 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.92 in / 23 mm CROSSOVER PHYSICAL SPECIFICATIONS: Width (W): 1.96 in / 50 mm Height (H): 0.90 in / 23 mm Depth (D): 1.34 in / 34 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with dual true, edge-driven, aluminium dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension. Both high-frequency drivers also benefit from the damping of a silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 36 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.94 in / 100 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 3.09 in / 79 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many “6-inch” speaker locations as well. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 48 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.25 in / 159 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 5.02 in / 128 mm Mounting Depth (G): 2.07 in / 53 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 54 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.83 in / 132 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.54 in / 14 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 4.70 in / 119 mm Mounting Depth (G): 2.42 in / 62 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 35 W Peak Music Power: 105 W Recommended Amplifier Power (RMS): 10 – 50 W / Ch. System Efficiency: 84.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 64 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 4.03 in / 102 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.33 in / 59 mm Frontal Coaxial Tweeter Protrusion** (D): 0.61 in / 16 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 3.70 in / 94 mm Mounting Depth (G): 1.81 in / 46 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-650x system features 6.5-inch (165 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6.5-inch (165 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 91 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 59 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-600x system features 6-inch (150 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6-inch (150 mm) format is a direct fit in many vehicles. Multiple mounting patterns are provided on the woofer frame for easy installation into most vehicles that accept a 6.5-inch (165 mm) speaker. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair.

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. Many people mistakenly believe that an oval speaker cannot perform as well as around one, leading to many instances of 5.25-inch speakers being installed into 5 x 7-inch openings. JL Audio has put in the engineering time and effort to create fantastic-sounding speakers that drop into oval openings and deliver equivalent performance to our 6.5-inch (165 mm) round speaker systems... guaranteed. So, don't make the mistake of losing cone area and efficiency by stepping down to a smaller round speaker... these ovals are as impressive as our round format systems. The C2-570x system features 5 x 7 / 6 x 8-inch (125 x 180 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Grilles are not available for this speaker system. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 90.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-525x system features 5.25-inch (130 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 60 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 100 W / Ch. System Efficiency 89.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 63 Hz - 22 KHz ± 3 dB

If you are seeking reference-grade sub-bass from a 10-inch driver, your search ends here. Total Car Audio in the UK called it like this when they reviewed the 10W7: "This gives an all-around performance of such high quality on every level, that bettering it will be very hard to achieve." Not only does the 10W7 deliver amazing excursion capability for its size, but it also maintains complete composure under power and is able to track complex bass material with uncanny accuracy and power. The 10W7AE is best used with amplifier power in the 300W - 750W range and is optimized to operate in a 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.5 cu. ft. (42.5 l) ported enclosure. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label Continuous Power Handling (RMS) 750 W Recommended Amplifier Power (RMS) 300 - 750 W Nominal Impedance (Znom) 3 Ω

This subwoofer driver has been called the "best damn 8-inch subwoofer ever made" for its remarkable performance capabilities and design attributes. An impressive linear excursion envelope that exceeds 0.75 in. (19 mm) one-way allows it to deliver impact well beyond the range of other 8-inch subwoofer drivers. The 8W7AE is best used with amplifier power in the 200W - 500W range and is optimized to operate in a 0.875 cu. ft. (24.8 l) sealed enclosure, or a 1.0 cu. ft. (28.3 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 200 - 500 W Nominal Impedance (Znom) 3 Ω

JL Audio patented thin-line woofer technology compresses the architecture of the 13TW5v2 using a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the speaker than with conventional designs, while allowing excellent linear excursion capability and mechanical stability. To unleash even more performance from this technology, the v2 improves upon the original 13TW5 with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is also available in single 2 ohm and si4-ohm4 ohm voice coil versions to fit a wide range of applications. In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 10-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer. The 13TW5v2 is best used with amplifier power in the 250W - 600W range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure.

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Deep, powerful and accurate JL Audio bass is now possible in more applications than ever. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability. The 12W3v3-4 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 1.125 cu. ft. (31.8 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 4 Ω

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability. The 12W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 2 Ω

This acclaimed subwoofer driver strikes an outstanding balance in power handling, enclosure requirements and excursion to deliver excellent results in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 10W3v3 to enhance linearity and reliability. The 10W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.  Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150- 500 W Nominal Impedance (Znom) 2 Ω

This acclaimed subwoofer driver strikes an outstanding balance in power handling, enclosure requirements and excursion to deliver excellent results in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 10W3v3 to enhance linearity and reliability. The 10W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.

If you need an 8-inch subwoofer that can create outstanding bass in extremely small enclosures, the 8W3v3 will do the job and surprise you with its power and accuracy. It employs the same technologies as its larger diameter brethren to deliver a whopping 0.375 in. (10 mm) of controlled, one-way, linear excursion. The 8W3v3-4 is best used with amplifier power in the 75W - 250W range and is optimized to operate in a tiny 0.30 cu. ft. (8.5 l) sealed enclosure, or a 0.35 cu. ft. (9.9 l) ported enclosure. Continuous Power Handling (RMS) 250 W Recommended Amplifier Power (RMS) 75- 250 W Nominal Impedance (Znom) 4 Ω

If you need a small-format subwoofer that really delivers in extremely small enclosures, this is where your search ends. The 6W3v3 is a true subwoofer, through-and-through. It employs the same technologies as its larger diameter brethren to deliver a whopping 0.35 in. (8.9 mm) one-way linear excursion. The 6W3v3-4 is best used with amplifier power in the 50W - 150W range and is optimized to operate in a tiny 0.15 cu. ft. (4.2 l) sealed enclosure, or a 0.25 cu. ft. (7.1 l) ported enclosure. Continuous Power Handling (RMS) 150 W Recommended Amplifier Power (RMS) 50 - 150 W Nominal Impedance (Znom) 4 Ω

The 12W0v3 is a rugged performer with excellent efficiency, excursion capability and linearity. The overall performance envelope that puts it right at the top of its price class. It features a beefy 2 in. diameter voice coil and our patented Elevated Frame Cooling design for enhanced power handling and reliability. The 12W0v3 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a moderately sized 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure.

The 10W0v3 is a rugged performer with excellent excursion capability and linearity and an overall performance envelope that puts it right at the top of its price class. It features a beefy 2 in. diameter voice coil and our patented Elevated Frame Cooling design for enhanced power handling and reliability.

"Focal IWT3Y200 2-Woofer Kit Woofers IWT3Y200 have been designed for drivers who want to replace their factory audio system with a high-quality solution by Focal that is fully compatible with the relevant Tesla models. Equipped with the Flax® cone, an exclusive Focal technology, they significantly improve the in-car listening experience. Designed and manufactured in France, the Tesla-compatible Focal Inside range allows an à la carte/personalised audio system configuration. Specifically designed for Model 3 and Model Y from car manufacturer Tesla®, the IW T3Y 200 woofers are aimed at drivers who wish to replace their OEM audio system with a Focal solution perfectly suited to their vehicle. Quick and easy to install, the IW T3Y 200 kit significantly improves the in-car listening experience. Designed and built in France, the speaker drivers boast the Flax sandwich cone, made from flax fibre. Renowned for its outstanding performance, this Focal technology helps to reproduce pure, natural and ultra-realistic sound. To further enhance its in-car performance, the IW T3Y 200 kit also includes a neodymium magnet. The Focal Inside kits for Tesla® vehicles offer a custom configuration and a 100% Plug & Play system. They allow you to set up the audio system of your choice and create the best possible listening experience. Product Compatibility Chart Make Model Years Notes Tesla Model 3 Tesla Model Y   Key Points Designed and built in France Compatible with Tesla® Model 3 and Model Y Enjoy the full benefits of high-fidelity Quick and easy to install with no vehicle modifications required Light and discreet components with a composite structure Perfect, seamless fit inside the cabin 100% Plug & Play system Specification Type 2 woofers kit Max. power 150W Nom. power 75W RMS Sensitivity (2.83V/1m) 91dB Frequency response 40Hz - 1500kHz Impedance 4Ω Woofer 8"" (200mm) Depth 11/4"" (31mm) Cone Flax® Voice coil diameter 11/2"" (38mm) Motor Neodymium Surround Butyl Cone diameter 200mm (8"") Grilles not included Net weight 850 Parameters Rdc 3.2Ω Fs 40Hz Mms 30g Cms 0.5mm/N Vas 35.7l Qts 0.6 Qes 0.64 Qms 8.5 Bxl 6N/A Sd 221cm² What's in the box 2 Woofers Quick start guide (English/ French/ German/ Italian/ Spanish/ Portugese/ Dutch/ Polish/ Russian/ Chinese/ Korean/ Japanese/ Arabic) Focal window sticker 2 Adhesive backed Focal Inside badges "

Front: IS TOY 690 SplitsRear: IC TOY 165Amplifier: Impulse4.320 Power 2x55WattsRMS to Front SpeakersHarnesses: IMP EXTENSION I/O and ISO IW TOY Y ISO   FRONT: IS TOY 690 is a two-way component kit with a 6×9‚Äô‚Äôwoofer and a tweeter enabling to equip factory locations up front and improving the musicality of numerous Toyota models. Reliable, neutral and powerful, the compactness and the ergonomics of the IS TOY 690 makes it easy to integrate thanks to the factory connectors. REAR: IC TOY 165 is a two-way coaxial kit with a 6¬Ω” woofer and a tweeter enabling to equip factory locations up front and improving the musicality of numerous Toyota models. Excellent reliability, neutral sound and deep bass, compact and ergonomic, the IC TOY 165 kit has been designed respecting the factory connectors for a real facilitated integration. AMPLIFIER: Give your head unit a breath of fresh air. Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. It will give your installation a boost without you having to embark on a difficult installation process. HARNESSES: Compatible with the IMPULSE 4.320 compact 4-channel digital amplifier, the IMP EXTENSION I/O 150 extension cables with Plug & Play connections offer total installation freedom as they can connect each amplifier channel to one of the speaker drivers. Input/output extension: ‘Input’ to send the audio signal from the main unit to the amplifier and ‘output’ to send the signal leaving the amplifier to the original audio system.  AND: The Focal Inside TOYOTA Y-ISO HARNESS head unit adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Toyota original head unit and of Focal Inside extension cables.

Front: IS TOY 165 Splits or *IS TOY 165 TWU if no factory tweeter podsRear: IC TOY 165 Coaxial Sub:Subwoofer: PSB 200 8inch Subwoofer Mounted in Sealed EnclosureAmplifier: Impulse4.320 Power 2x55WattsRMS to Front Speakers, 1x160WattsRMS to SubwooferCables: IW IMP 2.1, IW TOY Y ISO 2006-2019 or IW TOY V2 Y ISO 2020-2023, IW PWSUP600 FRONT: IS TOY 165 is a two-way component kit with a 6¬Ω” woofer and a tweeter enabling to equip factory locations up front and improving the musicality of numerous Toyota models. Excellent reliability, neutral sound and deep bass, compact and ergonomic, the IS TOY 165 kit has been designed respecting the factory connectors for a real facilitated integration. OR: The IS TOY 165 TWU kit is designed for drivers who want to replace their original audio system with a quality sound solution. The speaker drivers integrate the Polyglass cone for defined midrange and the Aluminium/Magnesium inverted dome tweeter, a Focal technology allowing perfectly rendered trebles. REAR: IC TOY 165 is a two-way coaxial kit with a 6¬Ω” woofer and a tweeter enabling to equip factory locations up front and improving the musicality of numerous Toyota models. Excellent reliability, neutral sound and deep bass, compact and ergonomic, the IC TOY 165 kit has been designed respecting the factory connectors for a real facilitated integration. SUBWOOFER: The compact PSB200 measures less than 51/8″ deep (13cm deep, with the grille) and therefore slides easily into a car boot. And its size isn’t the only great feature: it is also easy to use and delivers quality sound performance thanks to its 8″ subwoofer that has 250 watts of power. Delivered with brackets, screws and a set of hook-and-loop fastener, PSB200 can be fixed in various locations in your vehicle and it perfectly completes a 2 or 3-way audio system while remaining discreet and delivering precise and dynamic bass.With this passive enclosure, discover the pleasure of all sound nuances during your drive. AMPLIFIER: Give your head unit a breath of fresh air. Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. It will give your installation a boost without you having to embark on a difficult installation process. HARNESSES: The Focal Inside IW IMP 2.1  car radio car radio adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the IMPULSE 4.320 to be easily connected to two front channels and a subwoofer (two bridged channels), such as the PSB 200, without changing the original wiring. The Focal Inside TOYOTA Y-ISO HARNESS head unit adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Toyota original head unit and of Focal Inside extension cables. OR: The Focal Inside I IW TOY Y-ISO HARNESS V2 car radio adaptation cable is designed for the IMPULSE 4.320  compact 4-channel digital amplifier. It allows the quick and simple connection of the Toyota original car radio and of Focal Inside extension cables.

FOCAL TOYOTA HILUX POWERED 6.2 PACK 2006-2019 FITS TOYOTA HILUX 2006-2019 Front: IS TOY 165 SplitsRear: IC TOY 165 CoaxialSubwoofer: PSB200Amplifier: Impulse 4.320 Power 2×55 Watts RMS to Front Speakers, 1×160 Watts RMS to SubwooferCables: IW IMP 2.1, IW TOY Y ISO HARNESS FRONT: The Focal Inside TOYOTA Y-ISO HARNESS head unit adaptation cable is designed for the IMPULSE 4.320 compact 4-channel digital amplifier. It allows the quick and simple connection of the Toyota original head unit and of Focal Inside extension cables. AMPLIFIER: Give your head unit a breath of fresh air. Head unit amplifiers (whether OEM or aftermarket) soon reveal their limits in terms of power and dynamics. At high volume, they soon saturate and ruin the listening pleasure. To compensate for this and to enable you to get the best out of your speaker drivers, Impulse 4.320 is the ideal solution. It will give your installation a boost without you having to embark on a difficult installation process. HARNESSES: Compatible with the IMPULSE 4.320 compact 4-channel digital amplifier, the IMP EXTENSION I/O 150 extension cables with Plug & Play connections offer total installation freedom as they can connect each amplifier channel to one of the speaker drivers. Input/output extension: ‘Input’ to send the audio signal from the main unit to the amplifier and ‘output’ to send the signal leaving the amplifier to the original audio system. 

"FOCAL INSIDE IW T3Y 2008"" WOOFERS FOR SELECT TESLA VEHICLES Improve the bass kick in your Tesla You enjoy the many benefits of your Tesla, but the bass response from the factory speakers may not be as electrifying as you'd like. But now the Inside Series brings Focal's famous sound to your electric vehicle. The best news of all is that Focal designs and builds these woofers to fit perfectly into Tesla Model 3 and Model Y vehicles. All the necessary mounting hardware is included, and integrated connectors connect to your existing factory speaker plugs — no cutting, splicing, or vehicle modifications required. This rear image of the woofer shows off the stiff flax weave that stays lightweight, so it's easier to drive. Famous Focal sound Focal incorporates their innovative flax woofer cones into the Inside IW T3Y 200 8"" woofers. Focal discovered that a flax woofer cone produces a dynamic sound that's worthy of its reputation. At half the weight of fiberglass, these flax fibers help create a very rigid yet lightweight cone that ensures accuracy and limits unwanted vibrations. This efficient design means you'll get more accurate, punchy bass from your music. Product highlights: two 8"" woofers designed to fit Tesla Model 3 and Model Y vehicles Tesla-specific wire connectors (no cutting required) 8"" flax woofer cone with butyl rubber surround neodymium magnets and 1.5"" voice coils impedance: 4 ohms power handling: 75 watts RMS (150 watts peak) frequency response: 40-1500 Hz sensitivity: 91 dB grilles not included warranty: 1 year MFR # IW T3Y 200 Item # 091IWT3Y20  Features & specs General Speaker Size Vehicle-specific Design 1-way Tweeter Design --- Impedance (Ohms) 4 Tweeter Composition --- Woofer Composition Flax Woofer Surround Butyl Rubber Parts Warranty 1 Year Labor Warranty 1 Year Specifications Sensitivity (1W at 1 meter) N/A Sensitivity at 2.83 volts 91 Frequency Response 40 - 1.5k Hz Minimum RMS Wattage --- Maximum RMS Wattage 75 Peak Power Handling (Watts) 150 Top-mount Depth (Inches) 1 3/8 Bottom-mount Depth (Inches) N/A Cutout Diameter or Length (inches) 3 3/4 Mounting Height (Inches) 1.375 Frame Width 8.44 Frame Length 8.44 What's in the box: 2 Woofers Quick start guide (English/ French/ German/ Italian/ Spanish/ Portugese/ Dutch/ Polish/ Russian/ Chinese/ Korean/ Japanese/ Arabic) Focal window sticker 2 Adhesive backed Focal Inside badges "