Car Audio Upgrades and Sound System Enhancements

4-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 4 @ 2 Ω / 75 W x 4 @ 4 Ω - 14.4V   The ultra-compact XDM400/4 packs a serious full-range punch, generating a whopping 100 watts to each of its four channels into 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM400/4 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Combine the XDM400/4 with our XDM600/1 monoblock to build a stunning 1000 W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat or deck. Or, use the XDM400/4 by itself to power two satellites, plus a subwoofer.  The XDM400/4 includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the rear channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 75 W RMS x 4 @ 2 Ω 100 W RMS x 4 Bridged @ 4Ω 200 W RMS x 2 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 4 @ 2 Ω 90 W RMS x 4 Bridged @ 4Ω 180 W RMS x 2 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 40 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or All channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 6.3 lb / 2.86 kg

2-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 2 @ 2 Ω / 75 W x 2 @ 4 Ω - 14.4V The tiny XDM200/2 packs a serious full-range punch, delivering a staggering 100 watts per channel into 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM200/2 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM200/2 includes a 12 dB / octave filter which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 75 W RMS x 2 @ 2 Ω 100 W RMS x 2 Bridged @ 4Ω 200 W RMS x 1 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 2 @ 2 Ω 90 W RMS x 2 Bridged @ 4Ω 180 W RMS x 1 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS  Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 20 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Security Cover for Controls Yes Pass-Through Preamp Output Buffered Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 6.85 in / 174 mm Depth (D) 7.09 in / 180 mm Net Weight 3.75 lb / 1.70 kg

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)   If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 12W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.02 in / 280 mm Bolt Hole Circle Diameter (C) 11.86 in / 301 mm Motor Outer Diameter (D) 7.0 in / 178 mm Mounting Depth (E) 7.52 in / 191 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.105 cu ft / 2.97 L Net Weight 25.6 lb / 11.6 kg Parameters Free Air Resonance (Fs) 26.919 Hz Electrical “Q” (Qes) 0.487 Mechanical “Q” (Qms) 9.365 Total Speaker “Q” (Qts) 0.463 Equivalent Compliance (Vas) 1.920 cu ft / 54.37 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 85.4 dB SPL Effective Piston Area (Sd) 75.338 sq in / 0.0486 sq m DC Resistance (Re)*** 6.493 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.0 cu ft / 28.3 L External Width (W) 15 in / 381 mm External Height (H) 15 in / 381 mm External Depth (D) 12 in / 305 mm F3 41.62 Hz Fc 45.99 Hz Qtc 0.7912 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.3 cu ft / 36.8 L External Width (W) 27 in / 686 mm External Height (H) 14 in / 356 mm External Depth (D) 12.5 in / 318 mm Internal Slot Port Width (SW) 1.75 in / 44 mm Internal Slot Port Height (SH) 12.5 in / 318 mm Internal Slot Port Length (SL) 37.125 in / 943 mm Port Extension Length (EL) 21.250 in / 540 mm Tuning Frequency (Fb) 33 Hz F3 31 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

6.5" (165 mm) Component Woofer (with Grille) Born from shared technologies used in our flagship C7 speakers, the C6-650cw component woofer benefits from vast woofer design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-650cw component woofer features a proprietary cast alloy frame outfitted with our Elevated Frame Cooling™ technology and a DMA-optimized motor system to generate outstanding midbass impact with ultralow distortion. Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor, such as the JL Audio TwK® DSP, or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-650cw Component Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grille Design Bandwidth:With 48 dB/octave filters: 55 Hz-6 kHzWith 24 dB/octave filters: 65 Hz-6 kHzWith 12 dB/octave filters: 80 Hz-6 kHz Component woofers are sold individually and include a plastic grille tray, one fine steel mesh grille and one electroformed JL Audio badge logo. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 55 Hz - 6 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-690tx system features 6 x 9-inch (150 x 230 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The 6 x 9-inch (150 x 230 mm) format is a direct fit in many vehicles. The Mid-Range driver is ferrofluid-cooled, with a 2-inch Mylar® cone diaphragm to smoothly bridge the gap between the woofer and the dome tweeter. Tweeters are mounted next to the mid-range driver and built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Woofer grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 70 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 15 - 125 W / Ch. System Efficiency 93 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 53 Hz - 22 KHz ± 3 dB

The Evolution C2 systems deliver sparkling high-frequency detail, smooth mid-range and powerful mid-bass, thanks to real silk dome tweeters and precision-engineered woofer designs. The C2-400x system features 4-inch (100 mm) woofers with mineral-filled polypropylene cones, long excursion capabilities and stamped steel frames. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. Breakaway mounting tabs on the woofer frame allow the C2-400x to be installed in four-hole or two-hole configurations. Injection-moulded adaptor plates are also included to allow mounting of the C2-400x speakers into a 4 x 6 (100 x 150 mm) speaker location. Tweeters are coaxially mounted and built with 0.75-inch silk dome diaphragms that deliver a smooth, extended response, on and off axis. The small size of the C2 tweeter minimizes tweeter protrusion, allowing C2 coaxials to fit behind most factory speaker grilles. Speaker grilles are included, each consisting of a black grille tray with satin silver accents and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Dynamic Sold as a pair. Continuous Power Handling (RMS) 35 W Peak Music Power 105 W Recommended Amplifier Power (RMS) 10 - 50 W / Ch. System Efficiency 84.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 71 Hz - 22 KHz ± 3 dB

The 12W7AE brings serious performance to the table by combining the breakthrough of the long-excursion W7 design with a large 12-inch bore. It has been called "addictive," "seductive" and "the new subwoofer reference", by some of the world's toughest reviewers, and has earned these accolades by delivering nearly limitless dynamics, exceptional balance and world-class sound quality. This potent driver is best used with amplifier power in the 400W - 1000W range and is optimized to operate in a 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but are they distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label Continuous Power Handling (RMS) 1000 W Recommended Amplifier Power (RMS) 400 - 1000 W Nominal Impedance (Znom) 3 Ω

Focal IS TOY 170 2-Way Component Speaker Kit for Toyota Camry XV70 Transform your driving experience with the Focal IS TOY 170, a premium 2-way component speaker kit designed specifically for the Toyota Camry XV70. Engineered in France, this vehicle-specific upgrade delivers exceptional sound quality while maintaining a factory-style appearance and straightforward installation. Featuring Focal's renowned Polyglass cone technology and aluminium/magnesium inverted dome tweeters, the IS TOY 170 produces rich midrange detail, punchy bass response, and crystal-clear high frequencies. Whether you're enjoying music, podcasts, or hands-free calls, every sound is reproduced with remarkable clarity and precision. The Plug & Play design uses vehicle-specific connectors and mounting points, allowing for a seamless installation without cutting wires or modifying your vehicle's interior. Simply replace the factory speakers and enjoy a significant improvement in audio performance. Key Features Designed specifically for Toyota Camry XV70 models Plug & Play installation with vehicle-specific connectors No cutting, wiring modifications, or interior alterations required Polyglass cone technology for detailed midrange and powerful bass Aluminium/Magnesium inverted dome tweeters for crisp, accurate high frequencies Improves overall soundstage, clarity, and listening enjoyment Developed and manufactured in France Integrated crossover design for simplified installation High 92.3dB sensitivity for efficient performance Specifications Speaker Type: 2-Way Component Speaker Kit Configuration: Split Component Sold As: Pair Impedance: 4 Ohms RMS Power Handling: 75 Watts Maximum Power Handling: 150 Watts Sensitivity: 92.3dB Frequency Response: 50Hz – 20kHz Woofer Size: 215mm x 267.4mm (6.5") Woofer Mounting Diameter: 172mm x 221.4mm Woofer Mounting Depth: 41.3mm Tweeter Size: 25mm (1") Tweeter Material: Aluminium/Magnesium Tweeter Style: Metal Inverted Dome Tweeter Mounting: Fixed Tweeter Swivel: No Tweeter Level Adjustment: No Crossover Type: Integrated Bi-Amp Capable: No Multi-Fit Midrange: No Grilles Included: No What's Included 1 Pair of Focal IS TOY 170 Component Speakers Integrated Crossovers Vehicle-Specific Mounting Hardware Screws and Installation Brackets Plug & Play Wiring Connections Benefits Significantly improves factory Toyota Camry audio performance Enhanced bass response and vocal clarity Greater detail and accuracy across all frequencies Factory-look installation with no visible modifications Quick and straightforward installation process Premium Focal sound tailored specifically for your Camry More Information Pair or Single Pair Speaker Type Split Component Speaker Setup 2-Way Woofer Diameter 215mm x 267.4mm (6.5") Mounting Diameter 172mm x 221.4mm Woofer Mounting Depth 41.3mm Tweeter Diameter 25mm (1") RMS Power 75W Impedance 4 Ohm Sensitivity 92.3dB Frequency Response 50Hz - 20kHz Tweeter Material Aluminium/Magnesium Tweeter Style Metal Tweeter Swivel No Tweeter Mount Fixed Tweeter Level Adjustment No Multi-Fit Midrange No Crossover Type Integrated Bi-Amp Capable No Grilles Included No

Elevate your factory audio system to an entirely new level with Alpine’s ‘direct-fit’ premium speaker upgrade to suit Toyota Hilux. Exclusively designed by Alpine, the tweeter housing achieves superior sound quality, as well as optimises staging and imaging. With its striking appearance and premium finishes inclusive of a machine finished metal Alpine emblem and ornate black chrome and metal ring accents to instantly enhance your in cabin aesthetic. The Alpine engineered and manufactured high-quality speaker housings ensures uncompromised sound performance with precise and direct replacement of the factory installed speakers. All parts are pre-assembled with ‘plug-n-play’ connections providing a straight forward, no-fuss installation with no need of any modifications, cutting of wires, nor soldering. Whatsmore, S-Series continues to establish the benchmark in sound quality and value by producing impressively detailed loudspeakers that accurately represent true studio-level Hi-Resolution audio faithful across the entire frequency bandwidth allowing the 1” soft dome tweeters come alive in the upper harmonics, delivering an incredibly smooth and detailed high frequency response that’s extended right up to 40kHz — so you can hear the finest nuances in your music. Take Hilux sound to the next-level with the new Hi-Resolution S-Series Premium Sound Solution. AN ALL-NEW AUDIOPHILE EXPERIENCE FOR S-SERIES What is Hi-Res Audio? With Hi-Res Audio streaming services and music downloads available you can now appreciate a higher sampling rate than in CD’s for the playback of music, which brings your favourite music tracks to life with extreme clarity. Alpine’s Hi-Res Audio Certified Head Units, Amplifiers and Digital Signal Processors are painstaking engineered to deliver faithful audio reproduction from high resolution sources and recordings with sample rates up to 192kHz/24Bit. These components are optimised for high definition playback and breathtaking performance, true to the artists original recording. Why Hi-Res Audio? Listening to Hi-Resolution Audio allows you to feel every emotion and hear every nuance; every detail of your favourite artist’s original studio performance is reproduced to perfection. Hi-Res Audio provides absolutely no distortion for the ultimate listening experience. Why Hi-Res Audio Certified Speakers? Hi-Res Audio goes beyond the limits of ordinary speakers. To accurately render the sound of Hi-Resolution sound sources and recordings in true high definition the reproduction of an extended dynamic frequency range right up-to 40kHz is paramount. Hi-Res Audio Certified All-New for S-Series, Hi-Res Audio Certification brings a whole new dimension of sonic excellence to your everyday drive. With an impressive extended dynamic range, playing upper harmonics all the way up to 40kHz, your tracks will come alive with a level of detail and nuance faithful to that of the original recording. Perfect Integration Alpine’s premium design ‘A Pillar’ direct-fit tweeter housings are made from premium injection moulded PC/ABS polymer and feature machine cut Alpine logo complimented by black chrome and machined metal accents which are all pre-assembled components ready for direct installation to suit your Toyota Hilux. Premium Design Tweeter Housing Premium audio never looked so good. The bold, yet ornate design of the tweeter housing directly replaces the OEM which elevates the interior aesthetic and optimises the tweeter axis for superior sound quality. Alpine Patented Technology for Superior Sound These speakers adopt a 35mm voice coil and a precision strontium magnet motor structure delivering extraordinary cone velocity for incredible linearity and powerful bass to get an exquisite listening and driving experience. Glass Fiber Composite Woofer Cone The woofer features an all-new glass fiber composite cone, which due to its directionally weaved construction is engineered to be far stronger than a traditional oval cone diaphragm. The resulting rigidity coupled to glass-fiber’s  lightness results in highly controlled cone excursion producing excellent audio reproduction. HAMR Surround Not only does Alpine’s patented High Amplitude Multi-Roll (HAMR) surround maintain full control over the cone at any stage of excursion for high SPL. It’s ability to far exceed the maximum linear excursion of regular domed surround allows for beautifully pure sound and punchy bass. Features Woofer 6.5″ (165mm) Lightweight Glass Fiber Composite Component Speaker HAMR (High Amplitude Multi-Roll) Surround Large 35mm Voice Coil Magnet Material: Strontium Ferrite Tweeter 1″ Extended-Range Soft Dome Magnet Material: Ferrite Application Type: Premium Direct-Fit OEM Replacement for Ranger Grill: Perforated Net Crossover Network Woofer: Copper Air-Coiled Wound Inductor Tweeter: High Quality Audio-Grade Polycap Power Handling Peak Power: 240 Watts RMS Power: 80 Watts (CTA-2031 Compliant) General Frequency Range: 55 Hz – 40 kHz Impedance: 4 Ohms Sensitivity: 88 dB/W Recommended Amplification: up to 80W RMS per channel

Elevate your factory audio system to an entirely new level with Alpine’s ‘direct-fit’ premium speaker upgrade to suit Toyota Hilux. Exclusively designed by Alpine, the tweeter housing achieves superior sound quality, as well as optimises staging and imaging. With its striking appearance and premium finishes inclusive of a machine finished metal Alpine emblem and ornate black chrome and metal ring accents to instantly enhance your in cabin aesthetic. The Alpine engineered and manufactured high-quality speaker housings ensures uncompromised sound performance with precise and direct replacement of the factory installed speakers. All parts are pre-assembled with ‘plug-n-play’ connections providing a straight forward, no-fuss installation with no need of any modifications, cutting of wires, nor soldering. Whatsmore, S-Series continues to establish the benchmark in sound quality and value by producing impressively detailed loudspeakers that accurately represent true studio-level Hi-Resolution audio faithful across the entire frequency bandwidth allowing the 1” soft dome tweeters come alive in the upper harmonics, delivering an incredibly smooth and detailed high frequency response that’s extended right up to 40kHz — so you can hear the finest nuances in your music. Take Hilux sound to the next-level with the new Hi-Resolution S-Series Premium Sound Solution. AN ALL-NEW AUDIOPHILE EXPERIENCE FOR S-SERIES What is Hi-Res Audio? With Hi-Res Audio streaming services and music downloads available you can now appreciate a higher sampling rate than in CD’s for the playback of music, which brings your favourite music tracks to life with extreme clarity. Alpine’s Hi-Res Audio Certified Head Units, Amplifiers and Digital Signal Processors are painstaking engineered to deliver faithful audio reproduction from high resolution sources and recordings with sample rates up to 192kHz/24Bit. These components are optimised for high definition playback and breathtaking performance, true to the artists original recording. Why Hi-Res Audio? Listening to Hi-Resolution Audio allows you to feel every emotion and hear every nuance; every detail of your favourite artist’s original studio performance is reproduced to perfection. Hi-Res Audio provides absolutely no distortion for the ultimate listening experience. Why Hi-Res Audio Certified Speakers? Hi-Res Audio goes beyond the limits of ordinary speakers. To accurately render the sound of Hi-Resolution sound sources and recordings in true high definition the reproduction of an extended dynamic frequency range right up-to 40kHz is paramount. Hi-Res Audio Certified All-New for S-Series, Hi-Res Audio Certification brings a whole new dimension of sonic excellence to your everyday drive. With an impressive extended dynamic range, playing upper harmonics all the way up to 40kHz, your tracks will come alive with a level of detail and nuance faithful to that of the original recording. Perfect Integration Alpine’s premium design ‘A Pillar’ direct-fit tweeter housings are made from premium injection moulded PC/ABS polymer and feature machine cut Alpine logo complimented by black chrome and machined metal accents which are all pre-assembled components ready for direct installation to suit your Toyota Hilux. Premium Design Tweeter Housing Premium audio never looked so good. The bold, yet ornate design of the tweeter housing directly replaces the OEM which elevates the interior aesthetic and optimises the tweeter axis for superior sound quality. Alpine Patented Technology for Superior Sound These speakers adopt a 35mm voice coil and a precision strontium magnet motor structure delivering extraordinary cone velocity for incredible linearity and powerful bass to get an exquisite listening and driving experience. Glass Fiber Composite Woofer Cone The woofer features an all-new glass fiber composite cone, which due to its directionally weaved construction is engineered to be far stronger than a traditional oval cone diaphragm. The resulting rigidity coupled to glass-fiber’s  lightness results in highly controlled cone excursion producing excellent audio reproduction. HAMR Surround Not only does Alpine’s patented High Amplitude Multi-Roll (HAMR) surround maintain full control over the cone at any stage of excursion for high SPL. It’s ability to far exceed the maximum linear excursion of regular domed surround allows for beautifully pure sound and punchy bass. Features Woofer 6.5″ (165mm) Lightweight Glass Fiber Composite Component Speaker HAMR (High Amplitude Multi-Roll) Surround Large 35mm Voice Coil Magnet Material: Strontium Ferrite Tweeter 1″ Extended-Range Soft Dome Magnet Material: Ferrite Application Type: Premium Direct-Fit OEM Replacement for Ranger Grill: Perforated Net Crossover Network Woofer: Copper Air-Coiled Wound Inductor Tweeter: High Quality Audio-Grade Polycap Power Handling Peak Power: 240 Watts RMS Power: 80 Watts (CTA-2031 Compliant) General Frequency Range: 55 Hz – 40 kHz Impedance: 4 Ohms Sensitivity: 88 dB/W Recommended Amplification: up to 80W RMS per channel

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 6W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on the front baffle Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 50 – 150W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 150 W Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh External Width (W) 14.125 in / 359 mm External Height (H) 9.625 in / 245 mm External Depth (D1) 5.125 in / 130 mm Net Weight 12 lb / 5.44 kg

Designed to simplify great audio, every VXi amplifier combines our advanced NexD2™ switching amplifier technology with an integrated, full-featured digital signal processor. The VX1000/1i monoblock subwoofer amplifier outputs up to 600 watts into 4 ohms, or a jaw-dropping 1000 watts into 2 ohms. A specialized, low-frequency version of our NexD2™ amplifier technology delivers rock-solid bass performance and fidelity, with outstanding efficiency. Compact dimensions with all connections placed on one side, via mating plugs, greatly simplify installation into tight spaces. Instead of traditional control knobs and switches, all amplifier adjustments and DSP functionality are configured via a compatible external device (PC, Tablet or Smartphone), with the appropriate JL Audio TüN™ Software application installed. INCLUSIONS: Power Connector (for 2 AWG wire) Analog Input/Pre-Out Harness Subwoofer Output Connector 6 ft A/B USB Cable

JL AUDIO CS110LG-TW3 SINGLE 10TW3 POWERWEDGE, SEALED, 2 Ω Product highlights • Peak Power Handling: 800W • RMS Power Handling: 400W • Dual 4 Ohm Voice Coils • Sealed Enclosure w/ Black Carpet Finish • 5/8" MDF Construction Subwoofer Features: 10" 2 ohm TW3 subwoofer driver Power Handling: Peak: 800 watts RMS: 400 watts Impedance: 2 ohms Mica-filled injection molded polypropylene cone Rubber woofer surround Dual 4 ohm voice coils Frequency response: 22-200 Hz Sensitivity: 82dB Comes with black steel mesh grille 2 Year Manufacturer's Warranty General Enclosure Features: Subwoofer mounting depth: 3-1/2" Subwoofer cutout diameter: 11-5/8" 5/8" MDF construction Sealed enclosure Black carpet covered cabinet One pair of 5-way binding posts on the left side of the enclosure Nickel plated push terminals Dimensions: 5-1/8"D x 6-5/8"D w/ grille x 21"W x 15-3/8"H

IW-IMP-EXT150 Impulse amp cable kit, facilitates quick install of Impulse amps to vehicles via ISO plugs Compatible with the IMPULSE 4.320 compact 4-channel digital amplifier, the IMP EXTENSION I/O 150 extension cables with Plug & Play connections offer total installation freedom as they can connect each amplifier channel to one of the speaker drivers. Input/output extension: ‘Input’ to send the audio signal from the main unit to the amplifier and ‘output’ to send the signal leaving the amplifier to the original audio system.    Developed with twisted cables to effectively eliminate disturbance Three different lengths to suit all vehicles Cut-resistant protective shield Great flexibility for the easiest possible installation Double In/Out connector to also receive the amplified signal from the IMPULSE 4.320 No soldering required Length: 5ft (1,50m)

R2-Series Premium Speaker System Suitable for Single-Cab LandCruiser 78 & 79 Series Turn up the bass in your Single-Cab 70 Series — the next Generation R-Series are born to be played loud with the all-new R-Series ‘direct fit’ premium aftermarket speaker upgrade. Alpine’s premium sound solution has been engineered to provide rock solid durability and good looks, with amazing sound and clarity. Equipped with Alpine’s huge R2-Series 6×9” speakers, experience punchy, concise bass as well as uncompromised sound performance and richness possible through Hi-Res Audio certification. Comfort and Convenience have not been forgotten. The LC70-269SC-R houses drink compartments capable of holding a 1.25 litre bottle to a 375ml can – including large pockets to hold maps, tablets, or books. For technological needs, there are USB charge ports in both door pods that allow charging of up to 4 devices at once. Built-in puddle lights also help light the way, assisting vehicle exits in unfamiliar situations. Formed from injection-moulded and highly-resistant PC/ABS polymers, each part is highly durable and structured to withstand almost anything life throws at it. The sleek yet tough design of the LC70-269SC-R elevates the interior aesthetic whilst honouring the rugged history of the vehicle itself. The updated LC70-269SC-R is the pinnacle of Hi-Fi sound performance, design and practicality. A must have accessory to ultimate 21st century off-road lifestyle. Perfect Integration Alpine’s premium sound upgrade for LC70 Series (Single Cab) is the complete audiophile and lifestyle solution. The huge 6×9-inch R2-Series speakers not only sound great, but also provide clean and concise bass performance. Alpine’s LC70-269SC-R combines rugged looks with subtle design cues from the vehicle itself to create a factory-look product for the 21st century. Light Up The Outdoors Avoid getting messy in the mud. Alpine’s puddle light is designed for all your outdoor adventures, illuminating the ground underneath and drawing attention at night. Never have to worry about muddy puddles again, as the ground will be lit up in style. Highly Durable Tough Grille  Without compromise, these flush-fit integrated speaker grilles have been engineered from a strong PC/ABS polymer blend, ensuring high durability and abrasion resistance. A high-gloss black Alpine emblem adorns the grille, providing a striking contrast and premium finish to each door. 4x USB Charging Ports The on-board USB inputs sit discreetly yet elegantly within the speaker pod design, allowing up to 4 devices such as a tablet or smartphone to charge at any one time. This provides a convenient USB charge point at each door, such as the front driver door, front passenger door, rear passenger left and right door. Premium Design Tweeter Housing LandCruiser 70 Series never looked so good. The bold design of the tweeter housing fits into the top dash corners directly replacing the OEM dash trim panels, providing perfect integration with an OEM look. With the tweeters up on the dashboard, the sound image is up high where it should be and overall sounds incredible. Carry Your Life With You Alpine’s design for the LC70 Series integrates a number of convenient necessities. Meticulously designed to accommodate both large bottles and small cans, as well as maps, tablets and almost anything else that will fit. Alpine’s 70 Series speaker solution is ready for your next adventure. Larger Magnet Structure The new R-Series speakers feature a larger magnet structure for incredible bass. Despite this, the driver depth is unchanged from the previous generation to retain installation versatility, but with improved performance. Glass-Fibre Reinforced Cone The high-performance midrange and woofer drivers feature an all-new glass-fibre reinforced cone. This material is extremely rigid and light-weight, resulting in exceptionally fast cone velocity and response time, delivering highly accurate music reproduction. Exclusive HAMR Surround Alpine’s High Amplitude Multi-Roll (HAMR) surround provides a greater maximum and linear cone excursion for high SPL. The HAMR surround maintains full control over the cone at any excursion stage for powerful bass and pure sound. High-Pass X-Over Network This small X-Over networks are very easy to install – in may cases you can keep the original wiring in the vehicle’s doors by simply putting this network in, saving lots of time during installation. You can adjust the tweeter level by -3dB / 0dB / +3dB.   FEATURES Tweeter Tweeter Type: 1” (2.5cm) Ring Radiator Tweeter Voice Coil Type: Dual Gap for optimum linearity and clarity Magnet Material: Neodymium Woofer Cone Material: Hybrid Multi Layer Cone Motor Technology: Linear Drive Technology Surround: HAMR Surround Voice Coil Type: Dual Gap Voice Coil for optimum linearity and clarity Magnet: Ultra High Density Neodymium Magnet DX Ring: DX Ring Wave Guide: Wave Guide Mounting: Shallow Mounting Design Mounting Adapters: Mounting Adapter Kit Included Design: Bi-Amp Ready Design SPECIFICATIONS General Peak Power Handling: 300W RMS Power Handling: 100W Nominal Impedance: 4ohms Frequency Response: 60Hz-40kHz In-Line High Quality Crossover 59mm Mounting Depth Neodymium Magnet Multi-layer Hybrid Cone Dual Gap Voice Coil All-New Design Circuit for Precision Response Dimensions Woofer Diameter (mm): 160mm x 240mm Woofer Diameter (in): 6″ x 9″ Woofer Mounting Diameter (mm): 167mm Woofer Mounting Diameter (in): 6-19/32″ Woofer Mounting Depth (mm): 75mm Woofer Mounting Depth (in): 3″ COMPATIBILITY Compatible with LandCruiser VDJ 76, 78 & 79 2009> onwards (Single-Cab Only)

The smoothness and transparency of a high-end silk dome tweeter combine with top-flight component woofer performance to create a loudspeaker system with exceptional refinement and dynamic capability. The C5-650 component system features 6.5-inch (165 mm) component woofers with die-cast alloy baskets and Kurt Müller cones and suspensions. This woofer benefits from JL Audio’s vast woofer design experience and advanced modelling systems. The C5 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off-axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. The flush-mount fixtures feature our RSR (Ratcheting Swivel Rotation) mechanism to allow precise tweeter aiming after installation. C5 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 100 W Peak Music Power: 200 W Recommended Amplifier Power (RMS): 50 - 150 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 300 Hz - 10 KHz ± 3 dB Voice Coil Resistance (Re): 3.245 Ω Frame Outer Diameter (A): 3.45 in / 88 mm Bolt Hole Circle Diameter (B): 3.15 in / 80 mm Mounting Hole Diameter (C): 2.87 in / 73 mm Grille Tray Outer Diameter (D): 3.95 in / 100 mm Frontal Grille Protrusion (E): 0.58 in / 15 mm Mounting Depth (F): 1.46 in / 37 mm Motor Outer Diameter (G): 2.36 in / 60 mm

There are times when an installation calls for a separate woofer and tweeter and other times when a coaxial is the better approach. With the Evolution® C3 Convertible Component Systems, the same product can be deployed in either configuration, delivering outstanding audio power and quality in each application. The C3-525 system features 5.25-inch (130 mm) component woofers with oversized 1.2-inch (30.5 mm) voice coils, mineral-filled polypropylene cones and injection-moulded polymer baskets. The woofer design benefits from JL Audio's vast woofer design experience and advanced modelling systems. The C3 tweeters are built with 1-inch silk dome diaphragms that deliver powerful, extended response, on and off axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. They can also be mounted onto the woofers in a coaxial format using the included fixtures. C3 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. Sonic character: Clean and Powerful Sold as a pair. Continuous Power Handling (RMS) 75 W Peak Music Power 225 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 90.0 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 48 Hz - 25 KHz ± 3 dB

Focal TBM Utopia M Pure Beryllium Tweeters (Pair) Experience the pinnacle of automotive high-frequency reproduction with the Focal TBM, a flagship tweeter developed as part of the prestigious Utopia M Series. Combining Focal's revolutionary M-profile pure Beryllium inverted dome with patented TMD® (Tuned Mass Damper) technology, the TBM delivers extraordinary detail, precision, and realism that redefine what's possible in a high-end car audio system. Designed, developed, and hand-built in Saint-Étienne, France, the TBM represents decades of Focal acoustic expertise. The pure Beryllium diaphragm provides exceptional rigidity with extremely low mass, allowing the tweeter to reproduce the finest musical details with remarkable transparency and accuracy. Combined with the unique M-profile geometry, the TBM achieves exceptional off-axis response and an expansive, lifelike soundstage. Patented TMD® surround technology further enhances performance by controlling resonance and reducing distortion, resulting in smoother, more natural high frequencies that remain fatigue-free even during extended listening sessions. Whether integrated into a complete Utopia M system or used within a custom high-end installation, the TBM delivers uncompromising treble performance worthy of the world's finest car audio systems. Key Features Designed, developed and hand-built in France Premium Utopia M Series tweeters sold as a pair Pure Beryllium M-profile inverted dome technology Patented TMD® (Tuned Mass Damper) surround technology Exceptional detail, clarity and high-frequency extension Ultra-wide frequency response from 1.5kHz to 50kHz High-efficiency neodymium motor structure Outstanding off-axis dispersion and soundstage performance Compact installation depth for custom applications Supplied with mounting hardware and grilles Why Choose the Focal TBM? The TBM is engineered for enthusiasts and installers who demand absolute sonic accuracy. Its pure Beryllium diaphragm delivers unparalleled speed and transparency, while TMD® technology helps eliminate unwanted resonance and distortion. The result is an effortless and highly detailed treble presentation that enhances every aspect of the listening experience, from delicate vocal textures to the finest musical nuances. Benefits Exceptional treble clarity and resolution Ultra-low distortion performance Wide and immersive soundstage Excellent off-axis response Natural, fatigue-free listening experience Perfect integration with Utopia M systems Premium French engineering and craftsmanship Specifications Product Type: Tweeter Tweeter Design: M-Profile Inverted Dome Diaphragm Material: Pure Beryllium Suspension Technology: Tuned Mass Damper (TMD®) Motor Structure: Neodymium RMS Power Handling: 20W RMS Maximum Power Handling: 200W Impedance: 4 Ohm Sensitivity: 95dB Frequency Response: 1.5kHz – 50kHz Suspension Material: Butyl Installation Depth: 20.5mm Weight: 120g More Information Product Type Tweeter Series Focal Utopia M Tweeter Material Pure Beryllium Tweeter Design M-Profile Inverted Dome Suspension Technology TMD® (Tuned Mass Damper) Motor Type Neodymium RMS Power 20W Maximum Power 200W Impedance 4 Ohm Sensitivity 95dB Frequency Response 1.5kHz - 50kHz Suspension Material Butyl Installation Depth 20.5mm Weight 120g Country of Manufacture France Grilles Included Yes Mounting Hardware Included Yes Sold As Pair What's Included 2 x Focal TBM Utopia M Tweeters Protective Grilles Mounting Brackets Installation Screws Installation Accessories

Store Pick-Up Only: This product is available for collection from our store only and is not available for shipping. Contact us on 1300 856 888 for more information or to confirm availability before placing your order.Product Description JIMNY STYLE | EXTERIOR Metio Premium Audio For Jimny 2018 > 3Dr Jimny 150W Peak Power 50W RMS 4Ω 5cm Roof Speaker with Gunmetal Grille 16.5cm Door Woofers High Quality Crossover Network Mounting Accessories

Alpine R2-Series Premium Speaker System – FORD RANGER PXII / PXIII (Front & Rear) Upgrade your Ford Ranger with powerful, high-resolution sound. The Alpine R2-Series Premium Speaker System is a direct-fit upgrade designed to deliver deep bass, crystal-clear highs, and true Hi-Fi performance — all without modifying your vehicle. Built specifically for the FORD RANGER PXII and PXIII, this complete front and rear speaker system transforms your in-car audio with premium materials, advanced engineering, and seamless integration. Key Benefits Direct-fit upgrade for FORD RANGER PXII / PXIII Complete front and rear speaker system Plug-and-play installation — no cutting or soldering required High-resolution audio with extended frequency response up to 40kHz Enhanced bass performance with larger magnet structure Premium tweeter housing for improved sound staging and interior aesthetics Vehicle Fitment FORD | RANGER | PXII / PXIII Direct Fit Integration Designed specifically for the Ford Ranger, this system integrates seamlessly with factory mounting points and wiring. All components are pre-assembled with plug-and-play connections, allowing for a straightforward installation with no modifications required. Premium Tweeter System 1” magnesium hard-dome tweeters for ultra-clear sound Hi-Res Audio certified with response up to 40kHz Swivel design to optimise sound direction and staging Custom A-pillar housing with premium Alpine finish Powerful Woofer Performance Glass-fibre reinforced cone for fast, accurate response Larger magnet structure for deeper, stronger bass HAMR surround for increased cone movement and output Shallow mounting design for easy installation Advanced Audio Engineering Dual gap voice coil for improved clarity and linearity High-quality in-line crossover network included Adjustable tweeter levels (-3dB / 0dB / +3dB) Bi-amp ready design for advanced setups Specifications Peak Power: 300W RMS Power: 100W Impedance: 4 Ohms Frequency Response: 65Hz – 40kHz Woofer Size: 16.5 cm (6.5") Mounting Depth: 5.9 cm Magnet: Neodymium Why Choose Alpine R2-Series Engineered specifically for vehicle-specific fitment Premium materials for superior sound quality Designed for both performance and aesthetics Trusted Alpine audio engineering FAQs Is this a direct fit for my Ranger?Yes, it is designed specifically for FORD RANGER PXII and PXIII models. Do I need to modify wiring?No, it features plug-and-play connections with no cutting or soldering required. Does this include both front and rear speakers?Yes, this is a complete front and rear speaker upgrade system. Will this improve bass performance?Yes, the upgraded magnet structure and HAMR surround provide significantly improved bass output. Upgrade Your Ranger’s Sound System Experience premium audio performance with a system designed specifically for your vehicle. The Alpine R2-Series delivers clarity, power, and precision in every drive.