All products (except on sale)

W1v3 12-inch Subwoofer (300 W, 4 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-4 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.21 Hz Electrical “Q” (Qes) 0.535 Mechanical “Q” (Qms) 8.2 Total Speaker “Q” (Qts) 0.502 Equivalent Compliance (Vas) 2.706 cu ft / 76.63 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.25% Efficiency (1 W / 1 m)** 86.1 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 3.915 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 39.63 Hz Fc 48.75 Hz Qtc 0.9338 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31.41 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W1v3 12-inch Subwoofer (300 W, 2 Ω) The 12W1v3 is a lightweight 12-inch driver with excellent performance capabilities at moderate power levels. It features moderate mounting depth with no pole-vent, so the rear of the motor structure can be placed directly against an enclosure boundary. Excellent excursion capability and linearity allow it to reproduce sub-bass with shocking extension and quality. Several of JL Audio's proprietary technologies enhance its performance and reliability. The 12W1v3-2 is best used with amplifier power in the 75W - 300W range and is optimized to operate in a compact 1.10 cu. ft. (31.5 l) sealed enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.25 in / 133 mm Mounting Depth (E) 5.41 in / 137 mm Driver Displacement 0.052 cu ft / 1.47 L Net Weight 12.2 lb / 5.5 kg Parameters Free Air Resonance (Fs) 26.55 Hz Electrical “Q” (Qes) 0.554 Mechanical “Q” (Qms) 8.731 Total Speaker “Q” (Qts) 0.521 Equivalent Compliance (Vas) 2.544 cu ft / 72.04 L One-Way Linear Excursion (Xmax)* 0.45 in / 11 mm Reference Efficiency (no) 0.23% Efficiency (1 W / 1 m)** 85.9 dB SPL Effective Piston Area (Sd) 81.426 sq in / 0.0525 sq m DC Resistance (Re) 2.210 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.10 cu ft / 31.5 L External Width (W) 16 in / 406 mm External Height (H) 16 in / 406 mm External Depth (D) 11 in / 279 mm F3 38.99 Hz Fc 48.39 Hz Qtc 0.9496 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.6 cu ft / 45.3 L External Width (W) 25 in / 635 mm External Height (H) 15.5 in / 394 mm External Depth (D) 13 in / 330 mm Internal Slot Port Width (SW) 1.5 in / 38 mm Internal Slot Port Height (SH) 14 in / 356 mm Internal Slot Port Length (SL) 30.75 in / 781 mm Port Extension Length (EL) 17 in / 432 mm Tuning Frequency (Fb) 31.79 Hz F3 31 Hz Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)   If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 12W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.02 in / 280 mm Bolt Hole Circle Diameter (C) 11.86 in / 301 mm Motor Outer Diameter (D) 7.0 in / 178 mm Mounting Depth (E) 7.52 in / 191 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.105 cu ft / 2.97 L Net Weight 25.6 lb / 11.6 kg Parameters Free Air Resonance (Fs) 26.919 Hz Electrical “Q” (Qes) 0.487 Mechanical “Q” (Qms) 9.365 Total Speaker “Q” (Qts) 0.463 Equivalent Compliance (Vas) 1.920 cu ft / 54.37 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 85.4 dB SPL Effective Piston Area (Sd) 75.338 sq in / 0.0486 sq m DC Resistance (Re)*** 6.493 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.0 cu ft / 28.3 L External Width (W) 15 in / 381 mm External Height (H) 15 in / 381 mm External Depth (D) 12 in / 305 mm F3 41.62 Hz Fc 45.99 Hz Qtc 0.7912 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.3 cu ft / 36.8 L External Width (W) 27 in / 686 mm External Height (H) 14 in / 356 mm External Depth (D) 12.5 in / 318 mm Internal Slot Port Width (SW) 1.75 in / 44 mm Internal Slot Port Height (SH) 12.5 in / 318 mm Internal Slot Port Length (SL) 37.125 in / 943 mm Port Extension Length (EL) 21.250 in / 540 mm Tuning Frequency (Fb) 33 Hz F3 31 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level. Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label General Specifications Continuous Power Handling (RMS) 1500 W Recommended Amplifier Power (RMS) 500 - 1500 W Nominal Impedance (Znom) Dual 1.5 Ω Physical Specifications Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14 in / 356 mm Mounting Hole Diameter (B) 11.9 in / 302 mm Bolt Hole Circle Diameter (C) 12.7 in / 323 mm Motor Outer Diameter (D) 8.38 in / 213 mm Mounting Depth (E) 10.5 in / 267 mm Driver Displacement 0.21 cu ft / 5.9 L Net Weight 52 lb / 23.6 kg Parameters Free Air Resonance (Fs) 23.5 Hz Electrical “Q” (Qes) 0.476 Mechanical “Q” (Qms) 7.517 Total Speaker “Q” (Qts) 0.448 Equivalent Compliance (Vas) 3.68 cu ft / 104.3 L One-Way Linear Excursion (Xmax)* 1.25 in / 32 mm Reference Efficiency (no) 0.27% Efficiency (1 W / 1 m)** 86.3 dB SPL Effective Piston Area (Sd) 107.35 sq in / 0.0693 sq m DC Resistance (Re)*** 2.41 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 1.875 cu ft / 53.1 L External Width (W) 16 in / 407 mm External Height (H) 16 in / 407 mm External Depth (D) 18.875 in / 479 mm F3 37.4 Hz Fc 40.5 Hz Qtc 0.77 Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 2.375 cu ft / 67.3 L External Width (W) 25.875 in / 657 mm External Height (H) 16 in / 406 mm External Depth (D) 17.25 in / 438 mm Internal Slot Port Width (SW) 2.25 in / 57 mm Internal Slot Port Height (SH) 14.5 in / 368 mm Internal Slot Port Length (SL) 26.25 in / 667 mm Port Extension Length (EL) 7.875 in / 200 mm Tuning Frequency (Fb) 34.6 Hz F3 30.3 Hz Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.

The TailGate Assist by HSP is designed to reduce the heaviness of the tailgate. It works via a twin strut system which effortlessly dampens the drop of the tailgate and reduces weight while inclining. What does this mean? You’ll always stay safe when loading and unloading your vehicle. Easy Installation Got a spare 20 minutes? Almost the whole HSP TailGate Assist range can be installed in less than 20 minutes and does not require any special skills to install. It’s quick, easy and stress-free. Two-Way Strut System The HSP TailGate Assist uses a two-strut system that works in perfect harmony. The first strut is designed to dampen the decline of the tailgate, so the user can let the tailgate drop without worrying. The second strut works by offsetting the tailgate’s weight when inclining, allowing for an effortless lift. Compatibility VW AMAROK

The TailGate Assist by HSP is designed to reduce the heaviness of the tailgate. It works via a twin strut system which effortlessly dampens the drop of the tailgate and reduces weight while inclining. What does this mean? You’ll always stay safe when loading and unloading your vehicle. Easy Installation Got a spare 20 minutes? Almost the whole HSP TailGate Assist range can be installed in less than 20 minutes and does not require any special skills to install. It’s quick, easy and stress-free. Two-Way Strut System The HSP TailGate Assist uses a two-strut system that works in perfect harmony. The first strut is designed to dampen the decline of the tailgate, so the user can let the tailgate drop without worrying. The second strut works by offsetting the tailgate’s weight when inclining, allowing for an effortless lift. Compatibility VW AMAROK

The HSP TailGate Lock is a truly revolutionary product allowing you to sync your tailgate with your existing vehicle remote. Works With Factory Remote Unlike other units on the market, the TailGate Lock by HSP fully integrates with your existing factory key and runs in sync with your vehicle’s pre-programmed key functionality. This also includes working with proximity sensors, door handles and automatic timed lock functions. Non-destructive, Plug and Play Installation HSP have made the TailGate Lock so easy to install that it should take 45 minutes to install. The unique system is plug and play and the only system that does not require any drilling Enhanced Security The electronic TailGate Lock by HSP is one of the best ways to keep your tools safe. Did you know that most canopies simply ‘lip’ over the tailgate? Meaning that if your tailgate is unlocked it would be very easy for someone to force your tailgate open. Features Manufacturing Quality: Compliant to ISO9001 Cycle Testing: 100,000 switching cycles Operating temperature: -40 to 80°C Vibration resistance: 2.7g Power Draw: Current consumption (blocking current) 6.7A Idling current 350MA Voltage Range 9-15 (rated 12V) Wiring: Plug and Play Compatibility VW AMAROK

The ultimate solution for easy access to the contents of your vehicles tub. Easily operated via a simple handle with multiple latching positions and a purpose built side rail. Built using heavy-duty steel and topped with a precision cut platform to wrap around the wheel arches. Powder Coated steel frame Spring-loaded latch pins allow you to position the tray into multiple positions 75% extension 250 kgs loading capacity (dispersed weight extended) Compatible with most bed/tub liners Precision cut platform

The HSP Load Bar. A roll top cross bar rack that is perfect for snow trips with the family, a tour de neighbourhood in some excessively tight lycra, or even a perfect spot to mount the shovel for your extremely competitive sandcastle building. Full Metal Frame The HSP Load Bar has a full metal frame meaning that your precious cargo are resting on a solid foundation. Roll R Cover Specific Design The Load Bar is designed specifically to suit the HSP Roll R Cover. Which means installation is as simple as can be. All you do is slide the assembled roll top cross bar rack into the HSP Roll R Cover T channel and away you go. Additionally, the product-specific design perfectly compliments the Roll R Cover… Compatible with Common Accessories The HSP Load bar has a common channel that allows you to use accessories compatible with awesome roll top roof rack manufacturers such as Rhino-Rack, Thule, and Yakima. Compatibility VW AMAROK

What makes the S3.5 Roll R Cover So Special? HSP 4x4 did the impossible. They created the worlds most advanced retractable cover, packed with patented features, made it look incredible, made it work with your factory sports bar, your factory remote, even your mobile phone and even priced it lower than less feature-packed imported units 100% Australian Manufactured Yes, that’s right, the Roll R cover is the only 100% Australian made roll top, regardless of other companies sneaky play on words. On top of building them in Australia, HSP 4x4 decided to dig a bit deeper and have the manufacturing done in their custom-built facilities in Country Victoria, which has created so many Aussie jobs and is something they are very proud of. HSP 4x4 also design and test the units locally. World First Triple Operation The choice is literally in your hands! The HSP Roll R Cover gives you three methods of operation. Your factory remote, yes that’s right your existing factory remote automatically controls the unit A smart touchpad. Built into our super-sleek side rails, which allows you to open and close the unit with an effortless tap. And for security, the touchpad only works when your vehicle is unlocked. Mobile Phone Application and SIRI integration: Simply download the HSP 4×4 App on your iPhone or Android device to control your roll top. Plus a bonus for Apple users and it even works your iWatch and Air pods with Siri integration. Compatability Whether you’re a weekend warrior, the ultimate handyman or just a ute lover we made sure that the HSP 4x4 Roll R cover works for you. With the ability to retain your sports bars, ladder racks or cross bars the HSP electric roller cover truly allows you to customise your tub. Sports Bar Compatible Roll Top - Tired of sticking out? Not only can the HSP electric roller cover retain your factory bars, but the side rails also have pre-mapped insertion points so there is no additional height added. Ladder Rack Compatible Roll Top - The sky is the limit. If you have a big load, the Load Rack ladder rack system mounted to the Roll R Cover is perfect for you. Crossbar compatible Roll Top - Camping, snowboarding, mountain biking and pretty much anything else adventurous is now easier with the HSP Roll R Cover and Loadbar set up. Simply slide your load bar into the existing tracks and away you go! Horizon LED Light Bar A full length LED light is built into our canister meaning that you will have more than enough light for any of your night-time activities. You can also adjust the LED settings through the HSP App including light intensity and timing.  Super Simple Installation Fitting a HSP Roll R Cover is so simple! The roll-top itself is clamp-on, the electrics are plug and play, the unit is pre-programmed to your remote and the sports bars slot into pre-mapped insertion points. Water Protection Water issues are a thing of the past... The HSP Roll R Cover has a 6 point water flow system that drains at 60 litres per minute out of 4 oversized drainage points. Additionally, a new curtain grate drainage and the full-length gutter system and custom-designed seals ensure your tools and belongings are kept nice and dry from rain. Features Manufacturing Quality: Compliant to ISO9001 Curtain Material: Aluminium  Side Rail Material: Aluminium  Finish: Powdercoated Mannix Black LED Light Voltage: 12v Compliant with: EN 60529 Ed. 2.2: 2013: IP66 Remote Range: Same as Vehicle  Transmitter Coding: 220 constant rolling code Warranty: 3 years

What makes the S3.5 Roll R Cover So Special? HSP 4x4 did the impossible. They created the worlds most advanced retractable cover, packed with patented features, made it look incredible, made it work with your factory sports bar, your factory remote, even your mobile phone and even priced it lower than less feature-packed imported units 100% Australian Manufactured Yes, that’s right, the Roll R cover is the only 100% Australian made roll top, regardless of other companies sneaky play on words. On top of building them in Australia, HSP 4x4 decided to dig a bit deeper and have the manufacturing done in their custom-built facilities in Country Victoria, which has created so many Aussie jobs and is something they are very proud of. HSP 4x4 also design and test the units locally. World First Triple Operation The choice is literally in your hands! The HSP Roll R Cover gives you three methods of operation. Your factory remote, yes that’s right your existing factory remote automatically controls the unit A smart touchpad. Built into our super-sleek side rails, which allows you to open and close the unit with an effortless tap. And for security, the touchpad only works when your vehicle is unlocked. Mobile Phone Application and SIRI integration: Simply download the HSP 4×4 App on your iPhone or Android device to control your roll top. Plus a bonus for Apple users and it even works your iWatch and Air pods with Siri integration. Compatability Whether you’re a weekend warrior, the ultimate handyman or just a ute lover we made sure that the HSP 4x4 Roll R cover works for you. With the ability to retain your sports bars, ladder racks or cross bars the HSP electric roller cover truly allows you to customise your tub. Sports Bar Compatible Roll Top - Tired of sticking out? Not only can the HSP electric roller cover retain your factory bars, but the side rails also have pre-mapped insertion points so there is no additional height added. Ladder Rack Compatible Roll Top - The sky is the limit. If you have a big load, the Load Rack ladder rack system mounted to the Roll R Cover is perfect for you. Crossbar compatible Roll Top - Camping, snowboarding, mountain biking and pretty much anything else adventurous is now easier with the HSP Roll R Cover and Loadbar set up. Simply slide your load bar into the existing tracks and away you go! Horizon LED Light Bar A full length LED light is built into our canister meaning that you will have more than enough light for any of your night-time activities. You can also adjust the LED settings through the HSP App including light intensity and timing.  Super Simple Installation Fitting a HSP Roll R Cover is so simple! The roll-top itself is clamp-on, the electrics are plug and play, the unit is pre-programmed to your remote and the sports bars slot into pre-mapped insertion points. Water Protection Water issues are a thing of the past... The HSP Roll R Cover has a 6 point water flow system that drains at 60 litres per minute out of 4 oversized drainage points. Additionally, a new curtain grate drainage and the full-length gutter system and custom-designed seals ensure your tools and belongings are kept nice and dry from rain. Features Manufacturing Quality: Compliant to ISO9001 Curtain Material: Aluminium  Side Rail Material: Aluminium  Finish: Powdercoated Mannix Black LED Light Voltage: 12v Compliant with: EN 60529 Ed. 2.2: 2013: IP66 Remote Range: Same as Vehicle  Transmitter Coding: 220 constant rolling code Warranty: 3 years

What makes the S3.5 Roll R Cover So Special? HSP 4x4 did the impossible. They created the worlds most advanced retractable cover, packed with patented features, made it look incredible, made it work with your factory sports bar, your factory remote, even your mobile phone and even priced it lower than less feature-packed imported units 100% Australian Manufactured Yes, that’s right, the Roll R cover is the only 100% Australian made roll top, regardless of other companies sneaky play on words. On top of building them in Australia, HSP 4x4 decided to dig a bit deeper and have the manufacturing done in their custom-built facilities in Country Victoria, which has created so many Aussie jobs and is something they are very proud of. HSP 4x4 also design and test the units locally. World First Triple Operation The choice is literally in your hands! The HSP Roll R Cover gives you three methods of operation. Your factory remote, yes that’s right your existing factory remote automatically controls the unit A smart touchpad. Built into our super-sleek side rails, which allows you to open and close the unit with an effortless tap. And for security, the touchpad only works when your vehicle is unlocked. Mobile Phone Application and SIRI integration: Simply download the HSP 4×4 App on your iPhone or Android device to control your roll top. Plus a bonus for Apple users and it even works your iWatch and Air pods with Siri integration. Compatability Whether you’re a weekend warrior, the ultimate handyman or just a ute lover we made sure that the HSP 4x4 Roll R cover works for you. With the ability to retain your sports bars, ladder racks or cross bars the HSP electric roller cover truly allows you to customise your tub. Sports Bar Compatible Roll Top - Tired of sticking out? Not only can the HSP electric roller cover retain your factory bars, but the side rails also have pre-mapped insertion points so there is no additional height added. Ladder Rack Compatible Roll Top - The sky is the limit. If you have a big load, the Load Rack ladder rack system mounted to the Roll R Cover is perfect for you. Crossbar compatible Roll Top - Camping, snowboarding, mountain biking and pretty much anything else adventurous is now easier with the HSP Roll R Cover and Loadbar set up. Simply slide your load bar into the existing tracks and away you go! Horizon LED Light Bar A full length LED light is built into our canister meaning that you will have more than enough light for any of your night-time activities. You can also adjust the LED settings through the HSP App including light intensity and timing.  Super Simple Installation Fitting a HSP Roll R Cover is so simple! The roll-top itself is clamp-on, the electrics are plug and play, the unit is pre-programmed to your remote and the sports bars slot into pre-mapped insertion points. Water Protection Water issues are a thing of the past... The HSP Roll R Cover has a 6 point water flow system that drains at 60 litres per minute out of 4 oversized drainage points. Additionally, a new curtain grate drainage and the full-length gutter system and custom-designed seals ensure your tools and belongings are kept nice and dry from rain. Features Manufacturing Quality: Compliant to ISO9001 Curtain Material: Aluminium  Side Rail Material: Aluminium  Finish: Powdercoated Mannix Black LED Light Voltage: 12v Compliant with: EN 60529 Ed. 2.2: 2013: IP66 Remote Range: Same as Vehicle  Transmitter Coding: 220 constant rolling code Warranty: 3 years

What makes the S3.5 Roll R Cover So Special? HSP 4x4 did the impossible. They created the worlds most advanced retractable cover, packed with patented features, made it look incredible, made it work with your factory sports bar, your factory remote, even your mobile phone and even priced it lower than less feature-packed imported units 100% Australian Manufactured Yes, that’s right, the Roll R cover is the only 100% Australian made roll top, regardless of other companies sneaky play on words. On top of building them in Australia, HSP 4x4 decided to dig a bit deeper and have the manufacturing done in their custom-built facilities in Country Victoria, which has created so many Aussie jobs and is something they are very proud of. HSP 4x4 also design and test the units locally. World First Triple Operation The choice is literally in your hands! The HSP Roll R Cover gives you three methods of operation. Your factory remote, yes that’s right your existing factory remote automatically controls the unit A smart touchpad. Built into our super-sleek side rails, which allows you to open and close the unit with an effortless tap. And for security, the touchpad only works when your vehicle is unlocked. Mobile Phone Application and SIRI integration: Simply download the HSP 4×4 App on your iPhone or Android device to control your roll top. Plus a bonus for Apple users and it even works your iWatch and Air pods with Siri integration. Compatability Whether you’re a weekend warrior, the ultimate handyman or just a ute lover we made sure that the HSP 4x4 Roll R cover works for you. With the ability to retain your sports bars, ladder racks or cross bars the HSP electric roller cover truly allows you to customise your tub. Sports Bar Compatible Roll Top - Tired of sticking out? Not only can the HSP electric roller cover retain your factory bars, but the side rails also have pre-mapped insertion points so there is no additional height added. Ladder Rack Compatible Roll Top - The sky is the limit. If you have a big load, the Load Rack ladder rack system mounted to the Roll R Cover is perfect for you. Crossbar compatible Roll Top - Camping, snowboarding, mountain biking and pretty much anything else adventurous is now easier with the HSP Roll R Cover and Loadbar set up. Simply slide your load bar into the existing tracks and away you go! Horizon LED Light Bar A full length LED light is built into our canister meaning that you will have more than enough light for any of your night-time activities. You can also adjust the LED settings through the HSP App including light intensity and timing.  Super Simple Installation Fitting a HSP Roll R Cover is so simple! The roll-top itself is clamp-on, the electrics are plug and play, the unit is pre-programmed to your remote and the sports bars slot into pre-mapped insertion points. Water Protection Water issues are a thing of the past... The HSP Roll R Cover has a 6 point water flow system that drains at 60 litres per minute out of 4 oversized drainage points. Additionally, a new curtain grate drainage and the full-length gutter system and custom-designed seals ensure your tools and belongings are kept nice and dry from rain. Features Manufacturing Quality: Compliant to ISO9001 Curtain Material: Aluminium  Side Rail Material: Aluminium  Finish: Powdercoated Mannix Black LED Light Voltage: 12v Compliant with: EN 60529 Ed. 2.2: 2013: IP66 Remote Range: Same as Vehicle  Transmitter Coding: 220 constant rolling code Warranty: 3 years

The TailGate Assist by HSP is designed to reduce the heaviness of the tailgate. It works via a twin strut system which effortlessly dampens the drop of the tailgate and reduces weight while inclining. What does this mean? You’ll always stay safe when loading and unloading your vehicle. Easy Installation Got a spare 20 minutes? Almost the whole HSP TailGate Assist range can be installed in less than 20 minutes and does not require any special skills to install. It’s quick, easy and stress-free. Two-Way Strut System The HSP TailGate Assist uses a two-strut system that works in perfect harmony. The first strut is designed to dampen the decline of the tailgate, so the user can let the tailgate drop without worrying. The second strut works by offsetting the tailgate’s weight when inclining, allowing for an effortless lift. Compatibility VW AMAROK

The HSP TailGate Lock is a truly revolutionary product allowing you to sync your tailgate with your existing vehicle remote.   Works With Factory Remote Unlike other units on the market, the TailGate Lock by HSP fully integrates with your existing factory key and runs in sync with your vehicle’s pre-programmed key functionality. This also includes working with proximity sensors, door handles and automatic timed lock functions. Non-destructive, Plug and Play Installation HSP have made the TailGate Lock so easy to install that it should take 45 minutes to install. The unique system is plug and play and the only system that does not require any drilling Enhanced Security The electronic TailGate Lock by HSP is one of the best ways to keep your tools safe. Did you know that most canopies simply ‘lip’ over the tailgate? Meaning that if your tailgate is unlocked it would be very easy for someone to force your tailgate open. Features Manufacturing Quality: Compliant to ISO9001 Cycle Testing: 100,000 switching cycles Operating temperature: -40 to 80°C Vibration resistance: 2.7g Power Draw: Current consumption (blocking current) 6.7A Idling current 350MA Voltage Range 9-15 (rated 12V) Wiring: Plug and Play  Compatibility VW AMAROK

The HSP Load Slide is a purpose-built, retractable bed slide. Each unit has an entirely custom cut platform, contouring to your specific vehicle and is designed to give better access and management of your cargo. In other words, it’s the ultimate slide tray for your ride. 75% Platform Extension The Load Slide is operated via an easy-to-use handle that provides up to 75% extension beyond your tub. This provides simple and safe access to your goods when required. 250kg Weight Rating when Extended Combining advanced engineering with heavy-duty materials means the Load Slide can handle up to 250kg of dispersed weight when fully extended. Purpose Built Side Rails The custom cut heavy duty side rails are also designed to contour around the edges acting as a barrier and anchor points. This means you can move more with less effort than ever before. Custom Cut Platform One size fits all is for baseball caps and shortcut products. Your vehicle is unique, just like you, and so is the HSP platform. Using advanced CNC routing machines, The HSP Load Slide is completely custom cut to suit your specific requirements so there is no space wasted. Multiple Latching Positions The HSP Load slide has multiple latching positions every 20 centimetres allowing the user to stop and latch the load slide by simply letting go of the handle.

The HSP Load Slide is a purpose-built, retractable bed slide. Each unit has an entirely custom cut platform, contouring to your specific vehicle and is designed to give better access and management of your cargo. In other words, it’s the ultimate slide tray for your ride. 75% Platform Extension The Load Slide is operated via an easy-to-use handle that provides up to 75% extension beyond your tub. This provides simple and safe access to your goods when required. 250kg Weight Rating when Extended Combining advanced engineering with heavy-duty materials means the Load Slide can handle up to 250kg of dispersed weight when fully extended. Purpose Built Side Rails The custom cut heavy duty side rails are also designed to contour around the edges acting as a barrier and anchor points. This means you can move more with less effort than ever before. Custom Cut Platform One size fits all is for baseball caps and shortcut products. Your vehicle is unique, just like you, and so is the HSP platform. Using advanced CNC routing machines, The HSP Load Slide is completely custom cut to suit your specific requirements so there is no space wasted. Multiple Latching Positions The HSP Load slide has multiple latching positions every 20 centimetres allowing the user to stop and latch the load slide by simply letting go of the handle.