Fatz Fabrication PX RH Snorkel. Polished. Suit Bi Turbo 2.0L Factory Adaption Included-FFPX-SNRH-POL-FAB2 . Series 1-3 The Ford PX Ranger is one of the most weld rounded and well finished vehicles within their segment. With Performance to match their appearance. Our snorkels are designed to fit in a way to complement your vehicle and supply all the Airflow you could possible need. Built with 304 Grade Stainless steel for powder coated finish and 316 for polished finished snorkels, professionally TIG welded and polished to a seamless 320 grain finish, or powder coated Satin Black to match common bar work accessories and factory elements on your vehicle. Compatible with Ford PX Ranger, Series 1-3, the snorkel recesses into the guard to allow the snorkel to follow the body lines of the vehicle and the A pillar. Supplied in all cases with plumbing to the Airbox. If fitting to the Factory Airbox on the 2L, the factory inlet is blanked off and an adaption pipe is supplied to create a new inlet in a favorable location for plumbing to the snorkel. (For Ranger Raptor, Select specific product) NOTE:  Please note that some custom orders may require up to a 2-week wait for completion 

Fatz Fabrication PX RH Snorkel. Powder coated Satin Black. Suit Bi Turbo 2.0L Factory Adaption Included-FFPX-SNRH-SPC-FAB2 The Ford PX Ranger is one of the most weld rounded and well finished vehicles within their segment. With Performance to match their appearance. Our snorkels are designed to fit in a way to complement your vehicle and supply all the Airflow you could possible need. Built with 304 Grade Stainless steel for powder coated finish and 316 for polished finished snorkels, professionally TIG welded and polished to a seamless 320 grain finish, or powder coated Satin Black to match common bar work accessories and factory elements on your vehicle. Compatible with Ford PX Ranger, Series 1-3, the snorkel recesses into the guard to allow the snorkel to follow the body lines of the vehicle and the A pillar. Supplied in all cases with plumbing to the Airbox. If fitting to the Factory Airbox on the 2L, the factory inlet is blanked off and an adaption pipe is supplied to create a new inlet in a favorable location for plumbing to the snorkel. (For Ranger Raptor, Select specific product) NOTE:  Please note that some custom orders may require up to a 2-week wait for completion 

RA RAPTOR 5″ Snorkel inc Washer bottle The Ranger Raptor is a substantial step up in the current generation with power to support the exceptional chassis configuration. The Fatz Built RA RAPTOR 5" snorkel incorporates the true RAPTOR ethos with it's oversized yet refined styling. Our Snorkel is built in 304 Grade Stainless steel tube and finished to a true seamless form through a process developed over the 14 years we have been building snorkels. Then powder coated Satin Black to match common accessories on the market. Fitment is key with the need to align with body panels from any angle. Mounting to the A pillar is secure and robust with 3 M6 Nutcerts mounting the folded bracket. The RA comes from the factory with the washer bottle for the windscreen in the guard cavity making plumbing to the Airbox inlet difficult. Fatz has overcome this with our specifically designed Aluminium replacement unit which fits in the factory location. Resulting in the ability to plumb to the airbox inlet with 4" tubing for maximum airflow as required. Our snorkels are provided with all components required for installation including all plumbing items needed, cad drawn and scale printed templates, colour photo instruction manual, Fabricated washer bottle, plumbing to airbox and the confidence only purchasing with Fatz can bring. NOTE:  Please note that some custom orders may require up to a 2-week wait for completion 

The Ford PX Ranger series 3 Rangers 2L bi-turbo engine is a very impressive unit for its size and the fitment of a Fatz built Airbox and plumbing package will only compliment the OEM Hardware. Our Airbox utilizes our Fatz built Air filters in a 7” long element, either in an 8-layer gauze or paper element. The 2l Ranger Airbox includes all the design features that make Fatz built Airboxes a first choice for off road vehicles. With water trap and drain valve for dispersing water drawn in through the snorkel as well as a water deflector plate so water cannot hit the filter directly when taken in. This package will not only improve aesthetic of you engine bay, but will provide excellent filtration for Off-road use, allow easy plumbing in of Snorkels, provide a free flowing intake system that will support power upgrades. Compatible with all Ford PX Ranger 3, 2L ranger models including Raptor. The 2L Airbox incorporates our latest generation of MAF sensor integration with our CNC machines MAF housing for accurate and neat MAF integration. All plumbing supplied for a bolt in solution. Kit includes: Airbox with filter, Clear lid, instructions, mounting hardware, 3” 90degree silicone bend, joining pipe for silicone bends, 3”- 2.75” reducing silicone bend, Hose clamps as required.   NOTE:  Please note that some custom orders may require up to a 2-week wait for completion 

The Ford PX Ranger series 3 Rangers 2L bi-turbo engine is a very impressive unit for its size and the fitment of a Fatz built Airbox and plumbing package will only compliment the OEM Hardware. Our Airbox utilizes our Fatz built Air filters in a 7” long element, either in an 8-layer gauze or paper element. The 2l Ranger Airbox includes all the design features that make Fatz built Airboxes a first choice for off road vehicles. With water trap and drain valve for dispersing water drawn in through the snorkel as well as a water deflector plate so water cannot hit the filter directly when taken in. This package will not only improve aesthetic of you engine bay, but will provide excellent filtration for Off-road use, allow easy plumbing in of Snorkels, provide a free flowing intake system that will support power upgrades. Compatible with all Ford PX Ranger 3, 2L ranger models including Raptor. The 2L Airbox incorporates our latest generation of MAF sensor integration with our CNC machines MAF housing for accurate and neat MAF integration. All plumbing supplied for a bolt in solution. Kit includes: Airbox with filter, Clear lid, instructions, mounting hardware, 3” 90degree silicone bend, joining pipe for silicone bends, 3”- 2.75” reducing silicone bend, Hose clamps as required.   NOTE:  Please note that some custom orders may require up to a 2-week wait for completion 

This 1560mm/61.4" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Ford F-150 Raptor. Drilling is required for installation. This 1560mm/61.4" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Ford F-150 Raptor. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions, as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* For further information on installation, please see the fitment instructions in the INSTALL tab.Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:1x FAFF001 - Ford F-150 Super Crew (2009-Curr) Foot Rails/Low1x RRSTJ08 - SLII Tray - 1425mm(W)X1560mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 33.81kg (74.54lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 440mm (17")Length: 1730mm (68")Height: 310mm (12")Shipping Weight:Weight: 30kg (66lbs)

Guarantee all your gear arrives safely without compromising precious cargo space in your Ford F-150 Raptor 5.5' with these two low-profile, corrosion-free aluminum Load Bars. A set of Pickup Bed Load Bars used to transport gear over the bed of your Ford F-150 Raptor 5.5'. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickup’s load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:2x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK018 - Roof Load Bar Pair 1575mm(W)1x RRAC939 - Pickup Load Bed Bolt Kit / 30mm1x TRBU003 - Pick-Up Load Bed Tracks / 1400mm(L)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 12.02kg (26.5lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 160mm (6")Length: 1580mm (62")Height: 275mm (11")Shipping Weight:Weight: 12.2kg (27lbs)

Guarantee all your gear arrives safely without compromising precious cargo space in your Ford F-150 Raptor 5.5' with these three low-profile, corrosion-free aluminum Load Bars. A set of Pickup Bed Load Bars used to transport gear over the bed of your Ford F-150 Raptor 5.5'. This low profile solution includes 6 Pickup Roll Top Leg Mounts, 3 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickup’s load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:3x LASS028 - Pick-Up Roll Top Leg Mount1x LBSK019 - Roof Load Bar Set 1575mm(W)1x RRAC939 - Pickup Load Bed Bolt Kit / 30mm1x TRBU003 - Pick-Up Load Bed Tracks / 1400mm(L)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 16.46kg (36.29lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 1685mm (66")Length: 165mm (6")Height: 355mm (14")Shipping Weight:Weight: 16.4kg (36lbs)