The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs. By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Six (Front/Rear/Sub Output Pairs) Analog Output Unbalanced, stereo RCA jacks Digital Output N/A Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100 or DRC-200) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control) Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

The TwK™ 88 is a state-of-the-art digital signal processor engineered to deliver world-class system tuning capabilities in an easy-to-use format. Equipped with an advanced 24-bit DSP processor, the TwK™ 88 includes flexible input/output options, 80 total bands of equalization and powerful mixing tools. The included DRC-200 Digital Remote Controller offers dual level controls, toggles up to six presets, and has an LED indicator. Control the TwK™ 88’s entire feature set by connecting it to your PC via USB, using the companion TüN™ Software interface. FEATURES: Flexible input design with 8 differential-balanced, line-level analog inputs (RCA), accepting line-level signals up to 7.1V (RMS) Separate optical (Toslink) and coaxial digital inputs for connection to digital S/PDIF sources Flexible input mixer allows input channels to be combined with full control over each input’s level and polarity 8 banks of 10-band graphic or parametric equalizers with configurable EQ assignment Powerful crossover section with fully variable, high-pass and low-pass filters, crossover slopes are selectable from 6 dB/octave to 48 dB/octave (in 6 dB/octave increments) Configurable polarity and delay settings, with separate entries for speaker distance plus offset control; fully linkable with other channels, in any combination, for adjustment Precise output level controls, adjustable in 0.5 or 0.1 dB increments, fully linkable with other channels, in any combination 8 analog, line-level RCA output jacks (4V RMS) Optical (Toslink) output jack provides a pass-through digital audio (S/PDIF) signal from any pair of input channels, with no signal processing applied Remote turn-on output (+12VDC) for activating aftermarket audio equipment JLid™ Port allows connection of the included DRC-200 Digital Remote Controller to add dual configurable level controls, preset selection and LED status reporting from the driver's seat SPECIFICATIONS: Power Supply Type: Regulated DC-DC SMPS Input Operating Voltage: 10 - 16 VDC Standby Current Draw: <1.5 mA Operating Current Draw: 0.7 A Recommended Fuse Value: 1 A Input Channels: 8 Input Type: Line-level, Differential-Balanced Input Voltage Range: 250 mV - 7.1 V RMS Minimum Input Voltage: 10 mV RMS Input Level Setting: 11 discrete selections from 250 mV - 7.1V RMS Output Channels: 8 Analog Output: Unbalanced, stereo RCA jacks Digital Output: Optical (Toslink) output (S/PDIF) Output Impedance: 450 Ω Latency Analog - Analog: 5.425 mS Latency Analog - Optical: 5.470 mS Latency Optical - Optical: 4.860 mS Latency Optical - Analog: 4.805 mS S/N Ratio: 98 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output: 0.02% (20 Hz - 20 kHz) Audio Resolution: 24 bit / 48 kHz Number of EQ Bands: 10 x 8 Channels Remote Level Control: Included (DRC-200) Remote Level Functions: Master Volume Control + Trim; Master Volume Control + Fader; Zone Control, LED Status Reporting

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-650cw component woofer is capable of operating in a 3-way system, with a midrange and tweeter, or with only a tweeter in a 2-way configuration. Engineered from the ground up, it has exceptional linear excursion capability and outstanding linearity, resulting in solid mid-bass and pure, precise, mid-range performance. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Made in the USA with Global Components Sold individually, with a cast-alloy grille tray, one fine mesh steel grille insert and one spiral steel grille insert DESIGN FEATURES: Cone and Dust Cap: Vacuum-formed, mineral-filled polypropylene material offers excellent damping and low mass. The cone body features a gentle curvilinear profile to optimize response. A specially shaped dust cap attaches to the cone body and the voice coil former to improve high-frequency behaviour. Suspension design: The moving assembly is suspended and damped via a large-diameter, linear profile spider formed from a Nomex®/polycotton blend, and a positive-roll, rubber surround. The two combine to provide optimum damping without prematurely restricting the C7-650cw’s outstanding excursion capability. Motor Design: The C7-650cw employs a high-density magnetic circuit with a high-grade Y35 Strontium-ferrite magnet, and a specially machined, T-Yoke motor topology. Motor magnetics have been precisely optimized utilizing advanced FEA tools to reduce distortion and provide linear motor force throughout the driver’s performance range. A 32 mm (1.27 inch) diameter, the overhung voice coil is employed, wound with copper wire onto a fibreglass voice coil former. The oversized voice coil offers extended power handling capability, minimizing thermal compression and distortion at higher listening levels. Chassis Design: A purpose-engineered cast alloy basket is employed, featuring thin spokes to maximize rear open area and our patented Elevated Frame Cooling technology. DESIGN BANDWIDTH: With 48 dB/octave filters: 50 Hz – 5 kHz With 24 dB/octave filters: 60 Hz – 5 kHz With 12 dB/octave filters: 70 Hz – 5 kHz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 125 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 50 - 175 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 50 Hz - 5 KHz ± 3 dB Voice Coil Resistance (Re): 3.114 Ω Free Air Resonance (Fs): 54.5 Hz Reference Efficiency (no): 0.304% Efficiency: 87.0 dB @ 1W / 1m | 93.0 dB @ 1W / 0.5m Sensitivity: 90.0 dB @ 2.83V / 1m Electrical “Q” (Qes): 0.669 Mechanical “Q” (Qms): 6.265 Total Speaker “Q” (Qts): 0.605 Equivalent Compliance (Vas): 0.461 cu. ft. (13.05 liters) Moving Mass (Mms): 17.679 g Mechanical Compliance (Cms): 0.000482 m/N Magnetic Strength (BL): 5.31 N/A Effective Piston Area (Sd): 21.4 sq. in. (0.013807 sq. m) One Way Linear Excursion (Xmax): 5 mm

The smoothness and transparency of a high-end silk dome tweeter combine with top-flight component woofer performance to create a loudspeaker system with exceptional refinement and dynamic capability. The C5-650 component system features 6.5-inch (165 mm) component woofers with die-cast alloy baskets and Kurt Müller cones and suspensions. This woofer benefits from JL Audio’s vast woofer design experience and advanced modelling systems. The C5 component tweeters are built with 0.75-inch silk dome diaphragms that deliver smooth, extended response, on and off-axis. Flush-mounting and surface-mounting fixtures are included to fit a wide variety of installation needs. The flush-mount fixtures feature our RSR (Ratcheting Swivel Rotation) mechanism to allow precise tweeter aiming after installation. C5 crossover networks are compact and built with premium component parts, including Mylar® capacitors and segmented air-core inductors. Four levels of tweeter attenuation are provided, as well as three levels of mid-range presence adjustment, for twelve possible voicing combinations! Woofer grilles are included, each consisting of a black grille tray and a black steel mesh grille with an electroformed JL Audio logo. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 100 W Peak Music Power: 200 W Recommended Amplifier Power (RMS): 50 - 150 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 300 Hz - 10 KHz ± 3 dB Voice Coil Resistance (Re): 3.245 Ω Frame Outer Diameter (A): 3.45 in / 88 mm Bolt Hole Circle Diameter (B): 3.15 in / 80 mm Mounting Hole Diameter (C): 2.87 in / 73 mm Grille Tray Outer Diameter (D): 3.95 in / 100 mm Frontal Grille Protrusion (E): 0.58 in / 15 mm Mounting Depth (F): 1.46 in / 37 mm Motor Outer Diameter (G): 2.36 in / 60 mm

C7 is the pinnacle of JL Audio automotive loudspeaker design, benefiting from our most advanced development tools and a complete commitment to precision manufacturing. The C7-100ct component tweeter is designed to deliver unparalleled high-frequency performance. Utilizing a corundum ceramic-coated aluminium alloy diaphragm suspended via treated silk, s-roll surround, it provides spectacularly detailed reproduction of treble frequencies with an outstanding off-axis response. Distortion and non-linearities have been minimized through critical optimization of dynamic motor and suspension behaviours. Passive crossover networks are not included with C7 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning DSP, such as the JL Audio TwK™ 88 or D8, and a dedicated amplifier channel for each C7 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. Sold individually, with flush and surface mounting fixtures and hardware. One 15μF tweeter protection capacitor is also included. DESIGN FEATURES: Dome Diaphragm: Corundum ceramic-coated aluminium alloy diaphragm exhibits high stiffness, very low mass and excellent environmental stability. It also helps the tweeter dome to hold its shape and operate as a true piston at higher frequencies, without a penalty in moving mass. Suspension Design: The diaphragm’s motion is centred, sprung and damped by treated silk, s-roll surround. Ferrofluid in the magnetic gap acts as a rear suspension element in this design. The two combine to provide optimum damping without unduly restricting excursion. Motor Design: The C7-100ct employs a high-density magnetic circuit with a neodymium magnet and U-Yoke motor topology. An under-hung voice coil is employed, wound with copper-clad aluminium wire onto an aluminium voice coil former. Motor magnetics have been precisely optimized utilizing advanced FEA tools to lower even-order distortion and IMD/AMD. Acoustical Design: The shape of the tweeter housing is designed to boost sensitivity in a very specific bandwidth, helping to flatten the frequency response. It also provides improved control of directivity. DESIGN BANDWIDTH: With 48 dB/octave filters: 3,000 Hz – 30,000 Hz With 24 dB/octave filters: 4,000 Hz – 30,000 Hz With 12 dB/octave filters: 5,000 Hz – 30,000 Hz GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 100 W Peak Music Power: 200 W Recommended Amplifier Power (RMS): 50 - 150 W / Ch. Nominal Impedance: 4 Ω Frequency Response: 3 kHz - 30 KHz ± 3 dB Voice Coil Resistance (Re): 3.20 Ω Free Air Resonance (Fs): 1450 Hz Reference Efficiency (no): 0.267% Efficiency: 86.5 dB @ 1W / 1m | 92.5 dB @ 1W / 0.5m Sensitivity: 89.5 dB @ 2.83V / 1m Flush Mount Fixture Diameter (A1): 2.13 in / 54 mm Surface Mount Fixture Diameter (A2): 2.16 in / 55 mm Flush Mount Mounting Hole Diameter (B): 1.88 in / 48 mm Flush Mount Mounting Depth (C): 0.73 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.33 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2): 1.06 in / 27 mm

Steel mesh grille insert for select JL Audio 13-inch subwoofer drivers. Provide attractive, sturdy protection to your subwoofer driver with this fine steel mesh grille insert, powder-coated in a satin black finish. The insert is designed to fit snugly onto the woofer’s grille receiver ring.

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 35 W Peak Music Power: 105 W Recommended Amplifier Power (RMS): 10 – 50 W / Ch. System Efficiency: 84.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 64 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 4.03 in / 102 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.33 in / 59 mm Frontal Coaxial Tweeter Protrusion** (D): 0.61 in / 16 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 3.70 in / 94 mm Mounting Depth (G): 1.81 in / 46 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 54 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 5.83 in / 132 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 2.76 in / 70 mm Frontal Coaxial Tweeter Protrusion** (D): 0.54 in / 14 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 4.70 in / 119 mm Mounting Depth (G): 2.42 in / 62 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the speaker will fit into many “6-inch” speaker locations as well. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 48 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.25 in / 159 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): 5.02 in / 128 mm Mounting Depth (G): 2.07 in / 53 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with dual true, edge-driven, aluminium dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension. Both high-frequency drivers also benefit from the damping of a silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 90.5 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 36 Hz – 24 kHz ± 3 dB Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.94 in / 100 mm Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 3.09 in / 79 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings. Without the ring, the woofers will also fit into many “6-inch” speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion. Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 50 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 75 W / Ch. System Efficiency: 91.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 59 Hz – 22 kHz ± 3 dB Frame Outer Diameter* (A): 6.5 in / 165 mm Grille Tray Outer Diameter (B): 6.84 in / 174 mm Motor Outer Diameter (C): 3.15 in / 80 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion** (E): 0.85 in / 22 mm Mounting Hole Diameter (F): 5.56 in / 141 mm Mounting Depth (G): 2.44 in / 62 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.87 in / 48 mm Surface Mount Fixture Diameter (A2): 1.69 in / 43 mm Flush Mount Mounting Hole Diameter (B): 1.625 in / 41 mm Flush Mount Mounting Depth (C): 0.76 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.29 in / 7 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.92 in / 23 mm CROSSOVER PHYSICAL SPECIFICATIONS: Width (W): 1.96 in / 50 mm Height (H): 0.90 in / 23 mm Depth (D): 1.34 in / 34 mm

C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications. Surface and flush mounts are included with C1 tweeters for maximum installation versatility. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690 are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, 1-inch aluminium dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling. GENERAL SPECIFICATIONS: Continuous Power Handling (RMS): 60 W Peak Music Power: 225 W Recommended Amplifier Power (RMS): 10 – 100 W / Ch. System Efficiency: 89.0 dB @ 1 W / 1 m System Nominal Impedance: 4 Ω System Frequency Response: 39 Hz – 22 KHz ± 3 dB WOOFER PHYSICAL SPECIFICATIONS: Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B): N/A Motor Outer Diameter (C): 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D): N/A Frontal Grille Protrusion (E): N/A Mounting Hole Diameter (F): N/A Mounting Depth (G): 2.75 in / 70 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from the mounting surface TWEETER PHYSICAL SPECIFICATIONS: Flush Mount Fixture Diameter (A1): 1.97 in / 50 mm Surface Mount Fixture Diameter (A2): 2.01 in / 51 mm Flush Mount Mounting Hole Diameter (B): 1.75 in / 45 mm Flush Mount Mounting Depth (C): 0.40 in / 10 mm Flush Mount Tweeter Frontal Protrusion (D1): 0.32 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2): 0.87 in / 22 mm CROSSOVER PHYSICAL SPECIFICATIONS: Depth (D): 1.34 in / 34 mm Height (H): 0.90 in / 23 mm Width (W): 1.96 in / 50 mm

SPECIFICATIONSContinuous Power Handling (RMS): 600 WRecommended Amplifier Power (RMS): 250 - 600 WNominal Impedance (Znom): 2 ΩNominal Diameter: 13.5 in / 345 mmOverall Diameter (A) A1: 14.2 in / 361mmA2: 13.0 in / 330 mmMounting Hole Diameter (B): 12.5 in / 318 mmBolt Hole Circle Diameter (C): 13.5 in / 343 mmMotor Outer Diameter (D): 6.75 in / 171 mmMounting Depth (E): 2.625 in / 67 mmDriver Displacement: 0.052 cu ft / 1.47 LNet Weight: 20.5 lb / 9.3 kgPARAMETERSFree Air Resonance (Fs): 25.95 HzElectrical “Q” (Qes): 0.51Mechanical “Q” (Qms): 10.648Total Speaker “Q” (Qts): 0.479Equivalent Compliance (Vas): 2.26 cu ft / 64.00 LOne-Way Linear Excursion (Xmax)*: 0.433 in / 11 mmReference Efficiency (no): 0.23%Efficiency (1 W / 1 m)**: 85.51 dB SPLEffective Piston Area (Sd): 98.26 sq in / 0.0634 sq mDC Resistance (Re): 2.100 Ω* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.

GENERAL SPECIFICATIONS Continuous Power Handling (RMS): 300 WSystem Nominal Impedance: 4 ΩEnclosure Type: Slot-portedFinish: Gray carpetGrille Included: No PHYSICAL SPECIFICATIONSExternal Width (W) 16.31 in / 414 mmExternal Height (H) 15.18 in / 386 mmExternal Depth (D1) 20.3 in / 516 mmExternal Top Surface Depth (D2) 15.75 in / 400 mmNet Weight 33.1 lb / 15 kg

GENERAL SPECIFICATIONSContinuous Power Handling (RMS): 600 WSystem Nominal Impedance: 2 ΩEnclosure Type: Slot-portedFinish: Gray carpetGrille Included: NoPHYSICAL SPECIFICATIONSExternal Width (W): 31.375 in / 797 mmExternal Height (H): 15.18 in / 386 mmExternal Depth (D1)L 20.3 in / 516 mmExternal Top Surface Depth (D2): 15.75 in / 400 mmNet Weight: 60.3 lb / 27.35 kg

JL AUDIO JL AUDIO JD400/4 400W RMS JD SERIES CLASS-D 4-CHANNEL AMPLIFIER Premium Engineering Utilizing our exclusive NexD™ high-speed switching technologies, the JD400/4 amplifier is engineered to deliver loads of clean power, with excellent efficiency and low distortion. This little guy churns out 100 watts of audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms. The JD400/4’s controls can be found on the input panel of the amplifier, with all speaker and power connections located along the opposite end of the extruded aluminum chassis. Signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting line-level or speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment. Onboard LED-clipping indicators are also included surrounding each input sensitivity control. This convenient feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. You will also find a set of buffered, pass-through preamp outputs on-board, so you can pass signals to another amplifier. NexD Switching Technology Let's get a little nerdy... A traditional PWM switching amp design uses a fixed switching frequency and varies the pulse width based solely on the audio input signal to the pulse modulator. This basic approach assumes some ideal conditions, like a rock-steady power supply, that do not necessarily occur in a real, in-car installation. Power supply sag with signal causes distortion at all power levels with these designs, even well below clipping. The cure for this is feedback (a corrective signal sent back to the input side), but this becomes impractical as the audio frequency increases, making it a good solution for band-limited (subwoofer) amps, but not for full-range amplifiers. Taking the above into account when designing the NexD™ subwoofer amplifiers, we have taken the simple fixed PWM approach and enhanced it with a very high switching frequency: 240 kHz, which is about 4x higher than most Class D subwoofer amplifiers. This pushes the amplifier's bandwidth to at least 500 Hz with minimal distortion and improves efficiency, while keeping typically bulky circuity more compact. Your subwoofers will reward you with tight, rock-solid bass performance. For the full-range NexD™ amplifiers and channels we applied a variable, ultra-high speed version of the NexD™ technology (switching at well over 400 kHz). In these designs, a self-oscillating modulator with "feed-forward" sends information about the instantaneous power supply voltage to the modulator, combining this with the input signal to cancel out any distortion due to supply voltage fluctuation. This reduces distortion prior to applying feedback, simplifying the overall feedback loop design. Differential-Balanced Inputs Today’s vehicles are equipped with sophisticated electronics capable of generating noise and interference that can intrude into the audio path, ruining the listening experience. Most audio equipment uses single-ended, ground-referenced RCA jacks to receive audio signals. This means that the RCA shield is connected directly to the signal ground. This is a simple, cost-effective input design that works well for short runs in noise-free environments. In noisier environments, this method cannot reject the common mode noise that could be on both RCA conductors (shield and center conductor). By having more than one chassis-grounded RCA shield on a device, single-ended input designs are also more susceptible to ground loops. If noise is present on both conductors while the shield is connected to ground, the input amplifier will amplify the noise relative to the grounded RCA shield. When there are multiple RCA connections or any other conductors subjected to a magnetic field, this will cause a difference in potential across the RCA loop to be amplified at the grounded RCA as noise (a classic ground loop). JL Audio’s Differential-Balanced Input circuits measure the center pin of the RCA connection relative to the RCA shield, even when the shield is not connected to ground, and even when the voltages at both conductors are moving relative to ground. Because both the center conductor and the shield see high impedance to ground at the input, a ground loop cannot be formed, as there is no current flow to induce a voltage as noise. This works equally well with differential-balanced, or unbalanced signal sources, making this input architecture compatible with all standard car and marine audio equipment, using standard, unshielded, twisted-pair RCA cables. No special cables are required, unlike the fully balanced connections used in professional audio. Another benefit of the Differential-Balanced Input design is that it easily accepts low-level and high-level signals from a variety of factory head unit outputs and amplifiers, including single-ended “ground referenced” sources, as well as Balanced or Unbalanced “Bridged or BTL” sources. This eliminates the need for Line Output Converters (LOCs) in most installation scenarios. The obvious question is: “Why don’t all car audio amplifiers use Differential-Balanced Inputs?” The answer is simple: it costs more. Executing a proper differential-balanced input section requires more components and better quality components than a basic single-ended design, so you generally won’t find them on less expensive amplifiers. Product Details: JD Series Class D 2 ohms Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 100 watts x 4 channel Bridged: 200 watts x 2 channel @ 4 ohms Total power output: 400 watts LED Power/Protect Light Wired bass level remote control not included Speaker-level (high-level) inputs (Requires adapter like the JL Audio XD-CLRAIC2-SW) Signal sensing remote turn-on Protection Circuitry with Status LED NextD™ switching amp technology Differential-balanced inputs help eliminate noise Advanced Rollback Protection System prevents thermal shut-down Speaker-level (high-level) inputs Input sensitivity: Low level: 200mV - 2 volts High level: 800mV - 8 volts Frequency Response: 12 - 22000 Hz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: >104 dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Fuse Rating: 40A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 9-7/8" L x 7-1/2" W x 2-1/8" H Authorized Internet Dealer 2 Year Manufacturer's Warranty MFR #: JD400/4 Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer

JL AUDIO MICROSUB CP110LG-TW1-2 300 WATT RMS SINGLE 10" 10TW1-2 SUBWOOFER Product Highlights • Preloaded with single 10TW1-2 Subwoofer• Nominal Impedance: 2-ohms• Black, high-grade automotive carpet with silver embroidery• Efficient slot-ported design and precise tuning of its 10TW1 subwoofer• Sensitivity: 82.2 dB 1 watt / 1 meter General Features: Single 10" Vented Subwoofer Enclosure Preloaded with single 10TW1-2 Subwoofer RMS Power Rating: RMS: 300 watts Recommended power range: 75 - 300 watts RMS Nominal Impedance: 2 Ω Extensive interior bracing Steel mesh grille included Black, high-grade automotive carpet with silver embroidery Flared port entry and exit for enhanced sound quality Five-way binding post terminals for easy installation Precision-built in USA at JL Audio’s Miramar, Florida factory Long linear excursion capability (0.40 in / 10 mm, one-way) Efficient slot-ported design and precise tuning of its 10TW1 subwoofer Matching JL Audio Amplifier: JL Audio JX250/1 JL Audio XD300/1v2 - ✔ Preferred Match Authorized Internet Dealer 2 Year Manufacturer's Warranty General Specifications: Injection molded, mica-filled polypropylene cone Rubber surround No pole vent: permits mounting close to rear wall of enclosure DMA-optimized motor design Patented concentric tube architecture Patented floating cone attach method technology Cast alloy frame with flat edges for tight driver grouping Construction: CNC-Cut High-Grade MDF One-Way Linear Excursion (Xmax): 0.40 in / 10.0 mm Sensitivity: 82.2 dB 1 watt / 1 meter Enclosure Dimensions: 6.375" D x 20.875" W x 13.250" H Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer Item Details Manufacturer: JL AUDIO Model Number: CP110LG-TW1-2 Weight: 25.25lbs Internal SKU: cp110lgtw12

JL AUDIO CS113TG-TW5V2SINGLE 13TW5V2 TRUCK POWERWEDGE, SEALED, 2 Product highlights • 13.5" Loaded PowerWedge Truck Enclosure• 1200W Peak• 600W RMS• Comes Equipped with One JL Audio 13TW5-3v2 TW5 Thin-Line Subwoofer• High Grade Black Carpet Finish• Five-Way Binding Post Connectors Product Features:         13-1/2" TW5 (Thin-Line) Series Shallow Mount Subwoofer Power Handling: RMS: 600 watts Recommended Power Range: 250 - 600 watts Impedance: 2-Ohm Mica-filled polypropylene cone Santoprene surround Cast alloy basket 7-inch diameter voice coil Unique design allows for small airspace requirements Requires only 0.8 cubic feet of airspace 13% greater linear excursion capability over previous model Redesigned motor features an annular vent DMA-optimized motor designs   Patented floating cone attach method" technology Patented concentric tube architecture "Tab-Ear" frame design to fit driver in tight spaces Precision-built in USA at JL Audios Miramar, Florida factory Sensitivity: 85.63 dB Xmax: 11 mm Reference Efficiency (no): 0.2300% Frequency response: ~20 ~ 200 Hz Matching Amplifiers: JL Audio XD600/1v2 JL Audio 600/1v3 Authorized Internet Dealer 2 Year Manufacturer's Warranty General Enclosure Features: PowerWedge Sealed Truck Enclosure V-Groove MDF Construction advanced cabinet-building technique uses CNC machining to create precise panel joints Delivers world-class sub-bass fidelity Provides a detailed and smooth response High grade black carpet finish Five-Way binding post connectors Embroidered JL Audio logo JL Audio ECS internal wiring Steel mesh grille provides excellent woofer protection Designed to fit perfectly behind the seats of trucks Final Impedance: 2 ohm Weight: 34 lbs Dimensions: 4-1/2"TD x 7-1/4"BD x 21-1/4"W x 15-3/4"H Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer

JL AUDIO SB-TE-YG1/10TW1 TESLA MODEL Y STEALTHB OVERVIEW Tesla’s popular compact crossover delivers quick acceleration and a roomy cabin with plenty of space for both people and cargo. Sadly though, the factory audio options offer very little to satisfy in the bass reproduction departmen 10TW-1 SUBWOOFERS Featuring an all-fiberglass, custom-formed, sealed enclosure, this Stealthbox® houses an innovative. 10-inch TW1 thin-line subwoofer. Designed to drop into the driver’s side, rear storage compartment, this Stealthbox® solution produces amazing amounts of deep bass output, while practically vanishing into its surroundings. BUILT IN USA At a time when most audio products are built overseas, JL Audio’s commitment to in-house loudspeaker production continues to grow. To pull this off in a competitive world market, our production engineering team has created one of the world’s most advanced loudspeaker assembly facilities and established a global network of quality component suppliers who build to our specifications. This, combined with our commitment to state-of-the-art assembly technology, allows our skilled workforce to efficiently build JL Audio products to extremely high quality standards, right here in the U.S.A. INSTALL NOTES Use of driver's side, rear storage compartment is lost with installation. SPECIFICATIONS 2020-UP TESLA MODEL Y (5-SEAT) SUBWOOFERS 10TW1-2 POWER 300W RMS NOMINAL IMPEDANCE 2Ω MONO FEATURES BRAND JL AUDIO RMS POWER 300W RMS SHALLOW MOUNT YES SUBWOOFER SIZE 10"  

JL AUDIO CS110LG-TW3 SINGLE 10TW3 POWERWEDGE, SEALED, 2 Ω Product highlights • Peak Power Handling: 800W • RMS Power Handling: 400W • Dual 4 Ohm Voice Coils • Sealed Enclosure w/ Black Carpet Finish • 5/8" MDF Construction Subwoofer Features: 10" 2 ohm TW3 subwoofer driver Power Handling: Peak: 800 watts RMS: 400 watts Impedance: 2 ohms Mica-filled injection molded polypropylene cone Rubber woofer surround Dual 4 ohm voice coils Frequency response: 22-200 Hz Sensitivity: 82dB Comes with black steel mesh grille 2 Year Manufacturer's Warranty General Enclosure Features: Subwoofer mounting depth: 3-1/2" Subwoofer cutout diameter: 11-5/8" 5/8" MDF construction Sealed enclosure Black carpet covered cabinet One pair of 5-way binding posts on the left side of the enclosure Nickel plated push terminals Dimensions: 5-1/8"D x 6-5/8"D w/ grille x 21"W x 15-3/8"H