A set of Load Bars with Track Mounted Feet used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 2 50mm Feet, 2 60mm Feet, 2 1255mm Load Bars, 2 Ford Ranger 1200mm Tracks, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle. You may not have the need for a full roof rack and find that you can get by using a set of Front Runner Load Bars. These Load Bars are mounted to the vehicles roof via a set of supplied Tracks and Track Mounted Feet. Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred. Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack. Made from stainless steel and a durable, weather resistant black powder-coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRFM013 - Ford/Mazda T6/T7 (2012-2022) Load Bar Kit / Track & Feet - by Front Runner Consisting of: 1 x FASS012 - Foot Set / 40mm-50mm - by Front Runner 1 x FASS013 - Foot Set / 60mm-70mm - by Front Runner 1 x LBSK014 - Roof Load Bar Pair 1255mm(W) - by Front Runner 1 x TRFR001 - Ford Ranger (2012-Current) Tracks / 1200mm(L) - by Front Runner 1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 8kg (18lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 250mm (10") Length 1360mm (54") Height 110mm (4") Shipping Weight: Weight 9.3kg (20.5lbs)

Clear precious interior and load bed space, and still haul your adventure gear and toys with this Mazda BT50 (2012-2020) Slimline II Roof Rack Kit. This 1358mm/53.5” long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Mazda BT50. Easily installs using the existing factory mounting points. No drilling required. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 1 opening to access Front Runner under rack mount tables (1 smaller prep or 1 larger camp size table). All Front Runner Racks are backed by a Limited Lifetime Warranty* For further information on installation, please see the fitment instructions in the INSTALL tab. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:1x FAFR003 - Ford Ranger T6/Wildtrak (2012-Current) Foot Rails1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 28.91kg (63.74lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 440mm (17")Length: 1720mm (68")Height: 260mm (10")Shipping Weight:Weight: 30kg (66lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Mazda BT50 when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop-down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from stainless steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRRT005 - Mazda BT50 (2012-Current) EGR RollTrac Load Bed Load Bar Kit - by Front Runner Consisting of: 2x LASS028 - Pick-Up Roll Top Leg Mount 1x LBSK017 - Roof Load Bar Pair 1475mm(W) Material used: Black epoxy powder - coated T6 aluminium Approximate Installed Weight: 8.24kg (18.17lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 160mm (6") Length: 1590mm (63") Height: 290mm (11") Shipping Weight: Weight: 8.4kg (18lbs)

This kit creates a full-size rack that sits above your Mazda BT50's load bed when fitted with an EGR RollTrac cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1475mm x 1358mm) and 6 Pickup Roll Top Leg Mounts that fit into the existing EGR RollTrac channels. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRRT040T - Mazda BT50 (2012-Current) EGR RollTrac Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS028 - Pick-Up Roll Top Leg Mount 1x RRSTM07 - SLII Tray - 1475mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 30.46kg (67.15lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1720mm (68") Height: 240mm (9") Shipping Weight: Weight: 31kg (68lbs)

This 1358mm/53.5" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Mazda BT50. Easily installs using the existing factory mounting points. No drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 1 opening to access Front Runner under rack mount tables (1 smaller prep or 1 larger camp size table). All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRMB001T - Mazda BT50 (2020-Current) Slimline II Roof Rack Kit - by Front Runner Consisting of: 1x FAIK002 - Isuzu D-Max/Mazda BT 50 (2020-Current) Foot Rails 1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 28.67kg (63.21lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1730mm (68") Height: 260mm (10") Shipping Weight: Weight: 27.57kg (61lbs)

This 1358mm/53.5" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and two (2) Low Profile Foot Rails to mount the Slimline II Tray to your Mazda BT50 Double Cab. No drilling required. All Front Runner Rack Kits contain installation instructions, as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets. Features KRMB005T - Mazda BT50 (2020-Current) Slimline II Roof Rack Kit / Low Profile - by Front Runner Consisting of: 1x FAIK003 - Isuzu D-Max (2020-Curr) Foot Rails / Low Profile1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 29.13kg (64.22lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 255mm (10")   Shipping Weight: Weight: 30kg (66lbs)

This 1156mm/45.5" long, full-size, Slimline II cargo carrying roof rack kit for your Mazda BT50 Double Cab contains the Slimline II Tray, Wind Deflector, 2 Tracks and 4 Feet. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRMB003T - Mazda BT50 DC (2012-2020) SLII Roof Rack Kit Consisting of: 1x FASS012 - Foot Set / 40mm - 50mm1x FASS014 - Foot Set - Angled / 65mm1x RRSTD06 - SLII Tray - 1255mm(W)X1156mm(L)1x TRFR001 - Ford Ranger (2012-Current) Tracks / 1200mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 24.49kg (53.99lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18"); Length: 1715mm (68"); Height: 270mm (11")   Shipping Weight: Weight: 25.4kg (56lbs)

The Polyair Bellows load assist kits are specifically designed to suit leaf sprung vehicles.When you load up the back of the vehicle or hook up a caravan / trailer, you’ll notice the rear end drop down, this drop in height can have some adverse effects on your vehicle’s safety and handling.Symptoms such as:- Suspension bottoming out- Rough ride- Excessive sway & body roll- Unpredictable braking characteristics- Poor headlight aim- Clearance issues All this can be mitigated by installing a set of Polyair Bellows.The Bellows kit is air adjustable giving you flexibility to tailor the level of support for your individual load types and weights.Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the leaf springs are rated well past what you will carry daily, giving you a rough, uncomfortable ride when not loaded up.Having the flexibility of the adjustable Polyair Bellows means you can have a smooth stock ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features:- Air adjustable from 5-100psi- Built with a superior 2-ply fabric reinforced rubber- Ultra high strength & corrosion proof Zytel ® Nylon end caps- Most popular kits do not require drilling into the chassis- Easy to install with illustrated instructions- Quick connecting, easy to use air fittings.- Kits designed for standard height and raised applications- Bespoke design for each vehicle 2 year, unlimited km warranty. Position: Rear Ford - Ranger (T6) PX1, PX2, PX3 - 2011 - 2022, 2WD Mazda - BT50 2012-2020, 2WD

The Polyair Red Series load assist airbag kits are specifically designed to suit coil sprung vehicles. When you load up the back of the vehicle or hook up a caravan or trailer, you’ll notice the rear end drop down; this drop can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - suspension bottoming out - rough ride - excessive sway & body roll - unpredictable braking characteristics - poor headlight aim All this can be mitigated by simply installing a set of Polyair Red Series! The airbag kit is air adjustable, giving you flexibility to tailor the level of support for your individual load types and weights. Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the coil springs are rated well past what you will carry on a daily basis, giving you a rough, uncomfortable ride when not loaded up. Having the flexibility of the adjustable Polyair Red Series means you can have a smooth OEM ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features: - Air adjustable from 5-35psi - Tough moulded polyurethane construction - Easy to install using common tools - Easy to follow, illustrated instructions - Quick connecting, easy to use air fittings. 2 year, unlimited km warranty Position: Rear Ford - Escape 2000 - 2006 Mazda and Mazda - Tribute - 2000 - 2008, 4WD

The Polyair Bellows load assist kits are specifically designed to suit leaf sprung vehicles. When you load up the back of the vehicle or hook up a caravan / trailer, you’ll notice the rear end drop down, this drop in height can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - Suspension bottoming out - Rough ride - Excessive sway & body roll - Unpredictable braking characteristics - Poor headlight aim - Clearance issues All this can be mitigated by installing a set of Polyair Bellows. The Bellows kit is air adjustable giving you flexibility to tailor the level of support for your individual load types and weights. Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the leaf springs are rated well past what you will carry daily, giving you a rough, uncomfortable ride when not loaded up. Having the flexibility of the adjustable Polyair Bellows means you can have a smooth stock ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features: - Air adjustable from 5-100psi - Built with a superior 2-ply fabric reinforced rubber - Ultra high strength & corrosion proof Zytel ® Nylon end caps - Most popular kits do not require drilling into the chassis - Easy to install with illustrated instructions - Quick connecting, easy to use air fittings. - Kits designed for standard height and raised applications - Bespoke design for each vehicle 2 year, unlimited km warranty. Position: Rear Isuzu - D-Max Gen 3, 2020-on, 4WD (& 2WD HI-RIDE) Mazda - BT50 TF 2020-on

The Polyair Bellows load assist kits are specifically designed to suit leaf sprung vehicles. When you load up the back of the vehicle or hook up a caravan / trailer, you’ll notice the rear end drop down, this drop in height can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - Suspension bottoming out - Rough ride - Excessive sway & body roll - Unpredictable braking characteristics - Poor headlight aim - Clearance issues All this can be mitigated by installing a set of Polyair Bellows. The Bellows kit is air adjustable giving you flexibility to tailor the level of support for your individual load types and weights. Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the leaf springs are rated well past what you will carry daily, giving you a rough, uncomfortable ride when not loaded up. Having the flexibility of the adjustable Polyair Bellows means you can have a smooth stock ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features: - Air adjustable from 5-100psi - Built with a superior 2-ply fabric reinforced rubber - Ultra high strength & corrosion proof Zytel ® Nylon end caps - Most popular kits do not require drilling into the chassis - Easy to install with illustrated instructions - Quick connecting, easy to use air fittings. - Kits designed for standard height and raised applications - Bespoke design for each vehicle 2 year, unlimited km warranty. Position: Rear Ford - Ranger (T6) PX1, PX2, PX3 - 2011 - 2022, 4WD (& 2WD HI-RIDE) Mazda - BT50 2012-2020, 4WD (& 2WD HI-RIDE)

The Polyair Bellows load assist kits are specifically designed to suit leaf sprung vehicles. When you load up the back of the vehicle or hook up a caravan / trailer, you’ll notice the rear end drop down, this drop in height can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - Suspension bottoming out - Rough ride - Excessive sway & body roll - Unpredictable braking characteristics - Poor headlight aim - Clearance issues All this can be mitigated by installing a set of Polyair Bellows. The Bellows kit is air adjustable giving you flexibility to tailor the level of support for your individual load types and weights. Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the leaf springs are rated well past what you will carry daily, giving you a rough, uncomfortable ride when not loaded up. Having the flexibility of the adjustable Polyair Bellows means you can have a smooth stock ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features: - Air adjustable from 5-100psi - Built with a superior 2-ply fabric reinforced rubber - Ultra high strength & corrosion proof Zytel ® Nylon end caps - Most popular kits do not require drilling into the chassis - Easy to install with illustrated instructions - Quick connecting, easy to use air fittings. - Kits designed for standard height and raised applications - Bespoke design for each vehicle 2 year, unlimited km warranty. Position: Rear Isuzu - D-Max Gen 3, 2020-on, 4WD (& 2WD HI-RIDE) Mazda - BT50 TF 2020-on