This kit creates a full-size rack that sits above your Mazda BT50's load bed when fitted with an EGR RollTrac cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1475mm x 1358mm) and 6 Pickup Roll Top Leg Mounts that fit into the existing EGR RollTrac channels. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRRT040T - Mazda BT50 (2012-Current) EGR RollTrac Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS028 - Pick-Up Roll Top Leg Mount 1x RRSTM07 - SLII Tray - 1475mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 30.46kg (67.15lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1720mm (68") Height: 240mm (9") Shipping Weight: Weight: 31kg (68lbs)

This 1358mm/53.5" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Mazda BT50. Easily installs using the existing factory mounting points. No drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 1 opening to access Front Runner under rack mount tables (1 smaller prep or 1 larger camp size table). All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRMB001T - Mazda BT50 (2020-Current) Slimline II Roof Rack Kit - by Front Runner Consisting of: 1x FAIK002 - Isuzu D-Max/Mazda BT 50 (2020-Current) Foot Rails 1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 28.67kg (63.21lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1730mm (68") Height: 260mm (10") Shipping Weight: Weight: 27.57kg (61lbs)

This 1358mm/53.5" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and two (2) Low Profile Foot Rails to mount the Slimline II Tray to your Mazda BT50 Double Cab. No drilling required. All Front Runner Rack Kits contain installation instructions, as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets. Features KRMB005T - Mazda BT50 (2020-Current) Slimline II Roof Rack Kit / Low Profile - by Front Runner Consisting of: 1x FAIK003 - Isuzu D-Max (2020-Curr) Foot Rails / Low Profile1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 29.13kg (64.22lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 255mm (10")   Shipping Weight: Weight: 30kg (66lbs)

This 1156mm/45.5" long, full-size, Slimline II cargo carrying roof rack kit for your Mazda BT50 Double Cab contains the Slimline II Tray, Wind Deflector, 2 Tracks and 4 Feet. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRMB003T - Mazda BT50 DC (2012-2020) SLII Roof Rack Kit Consisting of: 1x FASS012 - Foot Set / 40mm - 50mm1x FASS014 - Foot Set - Angled / 65mm1x RRSTD06 - SLII Tray - 1255mm(W)X1156mm(L)1x TRFR001 - Ford Ranger (2012-Current) Tracks / 1200mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 24.49kg (53.99lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18"); Length: 1715mm (68"); Height: 270mm (11")   Shipping Weight: Weight: 25.4kg (56lbs)

MSA 4x4 BT50 Front & Rear Seat Covers- FRT516CO SUITS: BT50 FEATURES: Fully Airbag Compliant ADR Certified Integrated Lumber Support* Tight and secure fit 12oz specially manufactured Polycotton blend canvas Reinforced high wear areas for longevity Polycotton lined for maximum protection of the original vehicle seats Large rear pockets and head rest covers as standard INCLUDES: MSA 4x4’s Lifetime Guarantee Front twin bucket seats NOTE: DO NOT machine wash DO NOT scrub DO NOT apply detergent to clean

MSA 4x4 Ranger PJ/PK + BT50 DX Front Seat Covers- FRT511 SUITS: Ranger PJ/PK + BT50 DX Front twin bucket airbag seats FEATURES: Fully Airbag Compliant ADR Certified Integrated Lumber Support* Tight and secure fit 12oz specially manufactured Polycotton blend canvas Reinforced high wear areas for longevity Polycotton lined for maximum protection of the original vehicle seats Large rear pockets and head rest covers as standard INCLUDES: MSA 4x4’s Lifetime Guarantee NOTE: DO NOT machine wash DO NOT scrub DO NOT apply detergent to clean

MSA 4x4 Ranger & BT50 Single Cab Front Seat Covers- FRT516 SUITS: Ranger PX2 (08/16-07/19) Inc. Facelift Model Dual Cab/XLT +Ranger PX2 (08/16-07/19) Inc. Facelift Model Dual Cab/Single Cab/Single Space Cab/XL/XLS/XLT/Wildtrak + BT50 (06/18-09/20) XT Dual Cab (Facelift) + BT50 (06/18-09/20) XTR Dual Cab/Freestyle Cab (Facelift) + BT50 (01/17-05/18) Series 2 Dual Cab XTR/XT/Freestyle XTR/XT Single Cab Includes: Front twin bucket airbag seats with driver side only lumbar lever, console cover and integrated lumbar support FEATURES: Fully Airbag Compliant ADR Certified Integrated Lumber Support* Tight and secure fit 12oz specially manufactured Polycotton blend canvas Reinforced high wear areas for longevity Polycotton lined for maximum protection of the original vehicle seats Large rear pockets and head rest covers as standard INCLUDES: MSA 4x4’s Lifetime Guarantee NOTE: DO NOT machine wash DO NOT scrub DO NOT apply detergent to clean

MSA BT50 RIGHT STORAGE DRAWER SYSTEM-41003 SUITS: Mazda BT50 Designed from the ground up, the way a quality 4WD storage system should be. Sick of shoving everything loosely in the back of a vehicle? Why not get organised with an MSA 4X4 Storage Drawer System. MSA 4X4’s Storage Drawer Systems are designed with a patented slide technology Now fitted with fully sealed, stainless steel bearings with Nylon rollers as standard. Offering a quieter, smoother operation under heavy loads and saving up to 3kg per Drawer Module. The entire drawer extends further from the frame, allowing 100% access to the drawers. No more hard-to-reach items at the back! MSA 4X4’s Storage Drawer Systems are constructed from aluminium and have anodised aluminium components. Super-strong, lightweight and comes with stainless steel fasteners used throughout for a rust-free, corrosion resistance lifetime of use. The patented “Stay-Open Block” allows the drawer to remain in an open position even on a 30-degree slope. They also feature an LED Light Strip that activates at full extension and has a manual override switch. A 100% safe and secure lock system that can not be levered open from underneath, is an exceptional security measure. Dust resistant seals around front panels ensure all the items stored inside stay clean and dust free. Flush-fitting wing kits are available for most 4WDs and utes, creating additional storage space between the Storage Drawer System and the inner sides of the car. Access to the space is gained through removing the wing and face panels. The reinforced wing kit brackets provide a fully supported base for fridge slides to be mounted onto the wing panels, allowing for more placement options. The impact force of an unsecured item, within a vehicle during an accident, can be twenty to thirty times its static weight. Therefore greatly increasing the potential of occupant injuries. MSA 4X4’s Storage Drawer Systems, and the attachments that come with them (cargo barrier mount points and child restraint points), have been crash-tested and are fully ADR compliant. Tested to ADR3/02, ADR34/01 and ADR42 and passed all the requirements prescribed by the ADRs and AS/NZS, without any structural weaknesses or degradation of the system. FEATURES:  100% Drawer extension for complete access Patented “Stay-Open Block” Rust resistant sealed bearings with Nylon rollers Internal LED Light Strip Safe and secure lock system Dust resistant seal Stainless steel fasteners Removable wing and face panels INCLUDES: Complete wing kits Cargo Barrier mounting points Child restraint points MSA 4X4’s Lifetime Guarantee PARTS INCLUDED: Right Drawer Module Right Fit Kit (includes floor extension) Right Wing Kit Single Width Trim EXTERNAL DIMENSIONS +10mm for rear anchor bolts Overall drawer length = 1365mm (including handle lock) Overall drawer height = 275mm Overall single drawer width = 530mm (no wings) INTERNAL DIMENSIONS Usable drawer height = 215mm (upto under side of the top deck) Drawer height = 211mm Internal drawer length = 1250mm Internal drawer width = 453mm  

MSA BT50 LEFT STORAGE DRAWER SYSTEM-41002 Designed from the ground up, the way a quality 4WD storage system should be. Sick of shoving everything loosely in the back of a vehicle? Why not get organised with an MSA 4X4 Storage Drawer System. MSA 4X4’s Storage Drawer Systems are designed with a patented slide technology Now fitted with fully sealed, stainless steel bearings with Nylon rollers as standard. Offering a quieter, smoother operation under heavy loads and saving up to 3kg per Drawer Module. The entire drawer extends further from the frame, allowing 100% access to the drawers. No more hard-to-reach items at the back! MSA 4X4’s Storage Drawer Systems are constructed from aluminium and have anodised aluminium components. Super-strong, lightweight and comes with stainless steel fasteners used throughout for a rust-free, corrosion resistance lifetime of use. The patented “Stay-Open Block” allows the drawer to remain in an open position even on a 30-degree slope. They also feature an LED Light Strip that activates at full extension and has a manual override switch. A 100% safe and secure lock system that can not be levered open from underneath, is an exceptional security measure. Dust resistant seals around front panels ensure all the items stored inside stay clean and dust free. Flush-fitting wing kits are available for most 4WDs and utes, creating additional storage space between the Storage Drawer System and the inner sides of the car. Access to the space is gained through removing the wing and face panels. The reinforced wing kit brackets provide a fully supported base for fridge slides to be mounted onto the wing panels, allowing for more placement options. The impact force of an unsecured item, within a vehicle during an accident, can be twenty to thirty times its static weight. Therefore greatly increasing the potential of occupant injuries. MSA 4X4’s Storage Drawer Systems, and the attachments that come with them (cargo barrier mount points and child restraint points), have been crash-tested and are fully ADR compliant. Tested to ADR3/02, ADR34/01 and ADR42 and passed all the requirements prescribed by the ADRs and AS/NZS, without any structural weaknesses or degradation of the system. FEATURES:  100% Drawer extension for complete access Patented “Stay-Open Block” Rust resistant sealed bearings with Nylon rollers Internal LED Light Strip Safe and secure lock system Dust resistant seal Stainless steel fasteners Removable wing and face panels INCLUDES: Complete wing kits Cargo Barrier mounting points Child restraint points MSA 4X4’s Lifetime Guarantee PARTS INCLUDED: Left Drawer Module Left Fit Kit (includes floor extension) Left Wing Kit Single Width Trim EXTERNAL DIMENSIONS  +10mm for rear anchor bolts Overall drawer length = 1365mm (including handle lock) Overall drawer height = 275mm Overall single drawer width = 530mm (no wings) INTERNAL DIMENSIONS Usable drawer height = 215mm (upto under side of the top deck) Drawer height = 211mm Internal drawer length = 1250mm Internal drawer width = 453mm  

MSA RANGER & BT50 RIGHT STORAGE DRAWER SYSTEM-E1350-BT50-RIGHT-COM Designed from the ground up, the way a quality 4WD storage system should be. Suits Ford Ranger PX, PX2, PX3 & Mazda BT50 UP, UR Sick of shoving everything loosely in the back of a vehicle? Why not get organised with an MSA 4X4 Storage Drawer System. MSA 4X4’s Storage Drawer Systems are designed with a patented slide technology Now fitted with fully sealed, stainless steel bearings with Nylon rollers as standard. Offering a quieter, smoother operation under heavy loads and saving up to 3kg per Drawer Module. The entire drawer extends further from the frame, allowing 100% access to the drawers. No more hard-to-reach items at the back! MSA 4X4’s Storage Drawer Systems are constructed from aluminium and have anodised aluminium components. Super-strong, lightweight and comes with stainless steel fasteners used throughout for a rust-free, corrosion resistance lifetime of use. The patented “Stay-Open Block” allows the drawer to remain in an open position even on a 30-degree slope. They also feature an LED Light Strip that activates at full extension and has a manual override switch. A 100% safe and secure lock system that can not be levered open from underneath, is an exceptional security measure. Dust resistant seals around front panels ensure all the items stored inside stay clean and dust free. Flush-fitting wing kits are available for most 4WDs and utes, creating additional storage space between the Storage Drawer System and the inner sides of the car. Access to the space is gained through removing the wing and face panels. The reinforced wing kit brackets provide a fully supported base for fridge slides to be mounted onto the wing panels, allowing for more placement options. The impact force of an unsecured item, within a vehicle during an accident, can be twenty to thirty times its static weight. Therefore greatly increasing the potential of occupant injuries. MSA 4X4’s Storage Drawer Systems, and the attachments that come with them (cargo barrier mount points and child restraint points), have been crash-tested and are fully ADR compliant. Tested to ADR3/02, ADR34/01 and ADR42 and passed all the requirements prescribed by the ADRs and AS/NZS, without any structural weaknesses or degradation of the system. FEATURES:  100% Drawer extension for complete access Patented “Stay-Open Block” Rust resistant sealed bearings with Nylon rollers Internal LED Light Strip Safe and secure lock system Dust resistant seal Stainless steel fasteners Removable wing and face panels INCLUDES: Complete wing kits Cargo Barrier mounting points Child restraint points MSA 4X4’s Lifetime Guarantee PARTS INCLUDED: Right Drawer Module Right Fit Kit (includes floor extension) Right Wing Kit Single Width Trim EXTERNAL DIMENSIONS  +10mm for rear anchor bolts Overall drawer length = 1365mm (including handle lock) Overall drawer height = 275mm Overall single drawer width = 530mm (no wings) INTERNAL DIMENSIONS Usable drawer height = 215mm (upto under side of the top deck) Drawer height = 211mm Internal drawer length = 1250mm Internal drawer width = 453mm  

VEHICLE DATE: 09/2020-Current PRODUCT TYPE: Canvas Seat covers SUITS: BT50 XT/XTR/GT Single Cab Single Cab, twin bucket seats with integrated headrests, airbag, console cover and integrated lumbar support

VEHICLE DATE: 09/2020-Current PRODUCT TYPE: Canvas Seat covers SUITS: BT50 XT/XTR/GT Dual Cab 2nd row, 60/40 base with 3 headrests and no armrest

VEHICLE DATE: 09/2020-Current PRODUCT TYPE: Canvas Seat covers SUITS: BT50 XT/XTR/GT Dual Cab Complete front and rear covers, leather and fabric seats - (21007 + 21010)

VEHICLE DATE: 09/2020-Current PRODUCT TYPE: Canvas Seat covers SUITS: BT50 XT/XTR/GT Dual Cab Complete front and rear covers - (21007 + 21008)

MODULEMAP FOR MAZDA BT50 2.2L: 10/2011 – 06/2016 PERFORMANCE GAIN: 34KW / 116NM Access your BT50’s full potential with European race technology. A super-fast and powerful ECU programming tool, the ModuleMap allows you to calibrate and optimise your 2.2L, BT50 factory settings. Boost power and torque for an overall increase in performance Choose between three tunes instead of one permanent tune Return your vehicle to stock performance at any time Install in less than 30 minutes with simple plug-in software, and let Torqit’s software technicians do the rest Keep your vehicle safe and reliable with a tune that does not exceed the safety parameters or push it beyond its limits Instead of being locked into one permanent tune, Torqit’s ModuleMap gives you three tunes for total control over your vehicle’s performance. Cruise mode: ideal for everyday driving and towing heavy loads Sport mode: gives you maximum power and torque Standard Mode: a copy of the ECU, which returns your vehicle to stock performance

Ranger PX2 (08/16-07/19) Inc. Facelift Model Dual Cab/Single Cab/Single Space Cab/XL/XLS/XLT/Wildtrak + Ranger PX2 (05/15-07/16) Dual Cab/Single Cab/Single Space Cab/XL/XLS/XLT/Wildtrak + BT50 (06/18-09/20) XTR Dual Cab (Facelift) + BT50 (01/17-05/18) Series 2 Dual Cab XTR/XT/Freestyle XTR/XT Single Cab + BT50 (05/15-12/16) Series 2 Dual Cab XTR/XT/Freestyle XTR/XT Single Cab

Direction Plus™ Diesel Fuel Pre-Filter Kits protect late model common rail diesel engines against costly injector failure. Installing a Direction Plus™ Pre-Fuel Filter kit between the fuel tank and the O.E.M fuel filter will remove the majority of water and particle contamination. This leaves the O.E.M fuel filter to do the final and finer filtration, protectiing your diesel fuel system to the fullest.

Direction Plus™ Diesel Fuel Pre-Filter Kits protect late model common rail diesel engines against costly injector failure. Installing a Direction Plus™ Pre-Fuel Filter kit between the fuel tank and the O.E.M fuel filter will remove the majority of water and particle contamination. This leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system.