Subwoofer

Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line.  The MP 300 D2.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound.  The 65-mm 4-layer voice coil is higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 2 Ω + 2 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm). Size mm (in.) 300 (12) Power Handling - Continuous W 600 Power Handling - Peak W 1200 Impedance Ohm 2+2 No Filter Component Subwoofers Voice Coil Ø 65 (2,5) Magnet size D x d x h mm (in.) 164,5 x 75 x 35 (6.48 x 2.95 x 1.38) Weight of one component kg (lb.) 8,63 (19.03) Magnet High density flux ferrite Cone Pressed-pulp cone with mineral powders Xmech mm (in.) ±26 (1.02) D mm 260 Xmax mm ± 16,00 Re Ohm 1 (2 coils in PARALLEL) Fs Hz 23 Le mH 0,63 Vas I 88 Mms g 221 Cms mm/N 0,22 BL T*m 7,7 Qts 0,48 Qes 0,53 Qms 5,9 Spl dB 86 A 321 mm 12.64 in. B 284 mm 11.18 in. C 187 mm 7.36 in. D 164 mm 6.46 in. E 327,5 mm 12,89 in. F 59 mm 2.32 in.

Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line.  The MP 300 D4.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound.  The 65-mm 4-layer voice coil is higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 4 Ω + 4 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm).   Size mm (in.) 300 (12) Power Handling - Continuous W 600 Power Handling - Peak W 1200 Impedance Ohm 4+4 No Filter Component Subwoofers Voice Coil Ø 65 (2,5) Magnet size D x d x h mm (in.) 165 x 75 x 35 (6.5 x 2.95 x 1.38) Weight of one component kg (lb.) 8,63 (19.03) Magnet High density flux ferrite Cone Water-repellent pressed paper Xmech mm (in.) ±27 (1.06) D mm 260 Xmax mm 17 Re Ohm 1,9 Fs Hz 24 Le mH 1,6 Vas I 74 Mms g 235 Cms mm/N 0,19 BL T*m 12 Qts 0,42 Qes 0,45 Qms 5,9 Spl dB 86 A 321 mm 12.64 in. B 287 mm 11.3 in. C 187 mm 7.36 in. D 164 mm 6.46 in. E 327,5 mm 12.89 in. F 59 mm 2.32 in.

Designed for ML 2000.3, MG 200.3 grille features:1. Tailor-designed for Mille Legend/Pro subwoofers, providing total protection.2. Full metal sturdy structure composed by a solid cast aluminium ring and a steel mesh black grille featuring an elegant diamond-cut Hertz Logo3. Mounting screws totally hidden for a superior integration within the car cabin.4. M5 self-tapping hexagon socket screws with bit driver included. No Filter Component Grille A 233 mm 8.78 in. B 38 mm 1.5 in.

The APBX 10 S4S sealed enclosure is the ideal choice to be driven by the Audison AF M8.14 bit using two channels bridged. Designed to house the single 4 ohm voice coil APS 10 S4S subwoofer, it offers an ultra-performing Plug & Play solution boasting all the features that make the Prima boxes unique such as the SSP (Sub Smart Plug) terminal block for a quick connection leaving no room for errors. Technical Specs Nominal diameter 250 mm Impedance 4 Ohm Power Handling - Peak 800 W Power Handling - Continuous 400 W Magnet Material HIGH DENSITY FLUX FERRITE Cone Material COTTON-FIBRE PRESSES PAPER CONE Dimensions Dimension A 470 mm Dimension B 334 mm Dimension C 120 mm Dimension D 142 mm   Features Ultra-low profile (5.6 in. / 142 mm) box with a sealed design perfectly tuned to fully exploit the APS 10 D driver. 2 Sides/2 Sounds design provides the ability to choose between Down-Firing mounting to increase the low-frequency extension and Up-Firing installation to obtain more punch and definition. Leveling feet with Velcro inserts included for a secure grip on the carpet while maintaining easy removal. SSP (Sub Smart Plug) features both traditional push contacts and a Plug-&-Play terminal block to easily configure the impedance as required and provides a quick release. Rounded corners allow easy positioning in the trunk and act as reinforcement to reduce enclosure resonance. Special designed cone-dustcap-basket geometry which guarantees a long linear excursion capability (11 mm, one-way). Massive driver motor assembly, optimized with FEM (FiniteElement Modeling) for perfect control under high excursion conditions. Water-repellent treated paper 10 in. cone, featuring a profile developed with FEM simulation and optimized with the KlippelScan Vibrometer. Specifically developed to be combined with AF bit amplifiers taking advantage of the bass boost feature and integrated parametric equalizer of the built-in DSP. A sturdy metal grid is included for the total protection of the subwoofer driver.

SS 12 D2 subwoofer featuring 30 cm (12 in.) cone is eager to thrill the enthusiasts with their power.The suspension system reinforced with progressive double-layer spiders keeps the performance constant over time, especially in the heavy use typical of Bass Wars events.Heat dissipation is essential for this type of use and has been maximized thanks to an accurate design. The use of a robust 75 mm (3 in.) dual winding (2 + 2 Ω) voice coil developed in 4-layer configuration on a support with venting holes allows the SS 12 D2 to manage the impressive 2000 W peak power! The basket has been designed for optimal thermal dissipation and high mechanical resistance.The non-pressed paper cone with the addition of cotton fiber is the ideal compromise between stiffness and lightness, essential for a high sensitivity value. Suspension and leadwires are oversized to withstand the very high excursions generated by the massive ferrite engine.Push connectors accept cables with cross-section up to 12 AWG, for a practical and safe connection, suitable for the high currents involved. Size mm (in.) 300 (12) Power Handling - Continuous W 1000 Power Handling - Peak W 2000 Impedance Ohm 2+2 Depth mm (in.) 184 (7.24) Voice Coil Type dual No Filter Component SPL DUAL COIL SUBWOOFER Voice Coil Ø 75 (3) Magnet size D x d x h mm (in.) 170 x 90 x 40 (6.69 x 3.54 x 1.57) Weight of one component kg (lb.) 8,8 (19.4) Magnet Ferrite Cone Non pressed paper with cotton fibre Xmech mm (in.) 20,7 (0.81) D mm 253 Xmax mm 15,4 Re Ohm 0,96 Fs Hz 36 Le mH 0,9 Vas I 24,52 Mms g 282,8 Cms mm/N 0,07 BL T*m 9,37 Qts 0,64 Qes 0,70 Qms 7,0 Spl dB 86 A 320 mm 12.6 in. B 283 mm 11.14 in C 184 mm 7.24 in. D 161 mm 6.34 in.

SS 15 D2 subwoofers featuring 38 cm (15 in.) cone is eager to thrill the enthusiasts with their power.The suspension system reinforced with progressive double-layer spiders keeps the performance constant over time, especially in the heavy use typical of Bass Wars events.Heat dissipation is essential for this type of use and has been maximized thanks to an accurate design. The use of a robust 75 mm (3 in.) dual winding (2 + 2 Ω) voice coil developed in 4-layer configuration on a support with venting holes allows the SS 15 D2 to manage the impressive 2400 W peak power! The basket has been designed for optimal thermal dissipation and high mechanical resistance.The non-pressed paper cone with the addition of cotton fiber is the ideal compromise between stiffness and lightness, essential for a high sensitivity value. Suspension and leadwires are oversized to withstand the very high excursions generated by the massive ferrite engine.Push connectors accept cables with cross-section up to 12 AWG, for a practical and safe connection, suitable for the high currents involved. Size mm (in.) 380 (15) Power Handling - Continuous W 1200 Power Handling - Peak W 2400 Impedance Ohm 2+2 Depth mm (in.) 210 (8.27) Voice Coil Type dual No Filter Component SPL DUAL COIL SUBWOOFER Voice Coil Ø 75 (3) Magnet size D x d x h mm (in.) 180 x 90 x 40 (6.69 x 3.54 x 1.57) Weight of one component kg (lb.) 10,1 (22.27) Magnet Ferrite Cone Non pressed paper with cotton fibre Xmech mm (in.) 20,7 (0.81) D mm 323 Xmax mm 15,4 Re Ohm 0,96 Fs Hz 31 Le mH 1 Vas I 68,83 Mms g 361 Cms mm/N 0,07 BL T*m 10 Qts 0,61 Qes 0,66 Qms 7,4 Spl dB 88 A 390 mm 15.35 in. B 353 mm 13.9 in. C 210 mm 8.27 in D 188 mm 7.4 in. Frequency response

Monoblock Class D Car/Marine Subwoofer Amplifier, 600 W x 1 @ 2 Ω / 400 W x 1 @ 4 Ω - 14.4V This potent monoblock amplifier employs our high-speed NexD™ switching design to achieve unprecedented efficiency and amazing power output from a very compact chassis. Don't let its small size fool you, though... the XDM/600/1 generates serious subwoofer power, delivering a full 600 W of continuous power into a 2 ohm load (14.4V, 1% THD). Designed for car or boat installations, the XDM600/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Targeted specifically for subwoofer applications, the XDM600/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 400 W RMS x 1 @ 3 Ω 500 W RMS x 1 @ 2 Ω 600 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 300 W RMS x 1 @ 3 Ω 400 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >87 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >67 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter 30 Hz, defeatable Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 6.3 lb / 2.86 kg

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Deep, powerful and accurate JL Audio bass is now possible in more applications than ever. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

This acclaimed subwoofer driver strikes an outstanding balance in power handling, enclosure requirements and excursion to deliver excellent results in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 10W3v3 to enhance linearity and reliability. The 10W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.

This acclaimed subwoofer driver strikes an outstanding balance in power handling, enclosure requirements and excursion to deliver excellent results in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 10W3v3 to enhance linearity and reliability. The 10W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 0.625 cu. ft. (17.7  l) sealed enclosure, or a 1.25 cu. ft. (35.4 l) ported enclosure.  Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150- 500 W Nominal Impedance (Znom) 2 Ω

If you are seeking reference-grade sub-bass from a 10-inch driver, your search ends here. Total Car Audio in the UK called it like this when they reviewed the 10W7: "This gives an all-around performance of such high quality on every level, that bettering it will be very hard to achieve." Not only does the 10W7 deliver amazing excursion capability for its size, but it also maintains complete composure under power and is able to track complex bass material with uncanny accuracy and power. The 10W7AE is best used with amplifier power in the 300W - 750W range and is optimized to operate in a 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.5 cu. ft. (42.5 l) ported enclosure. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label Continuous Power Handling (RMS) 750 W Recommended Amplifier Power (RMS) 300 - 750 W Nominal Impedance (Znom) 3 Ω

The 12W7AE brings serious performance to the table by combining the breakthrough of the long-excursion W7 design with a large 12-inch bore. It has been called "addictive," "seductive" and "the new subwoofer reference", by some of the world's toughest reviewers, and has earned these accolades by delivering nearly limitless dynamics, exceptional balance and world-class sound quality. This potent driver is best used with amplifier power in the 400W - 1000W range and is optimized to operate in a 1.375 cu. ft. (38.9 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but are they distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label Continuous Power Handling (RMS) 1000 W Recommended Amplifier Power (RMS) 400 - 1000 W Nominal Impedance (Znom) 3 Ω

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)   If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 12W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.02 in / 280 mm Bolt Hole Circle Diameter (C) 11.86 in / 301 mm Motor Outer Diameter (D) 7.0 in / 178 mm Mounting Depth (E) 7.52 in / 191 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.105 cu ft / 2.97 L Net Weight 25.6 lb / 11.6 kg Parameters Free Air Resonance (Fs) 26.919 Hz Electrical “Q” (Qes) 0.487 Mechanical “Q” (Qms) 9.365 Total Speaker “Q” (Qts) 0.463 Equivalent Compliance (Vas) 1.920 cu ft / 54.37 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 85.4 dB SPL Effective Piston Area (Sd) 75.338 sq in / 0.0486 sq m DC Resistance (Re)*** 6.493 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.0 cu ft / 28.3 L External Width (W) 15 in / 381 mm External Height (H) 15 in / 381 mm External Depth (D) 12 in / 305 mm F3 41.62 Hz Fc 45.99 Hz Qtc 0.7912 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.3 cu ft / 36.8 L External Width (W) 27 in / 686 mm External Height (H) 14 in / 356 mm External Depth (D) 12.5 in / 318 mm Internal Slot Port Width (SW) 1.75 in / 44 mm Internal Slot Port Height (SH) 12.5 in / 318 mm Internal Slot Port Length (SL) 37.125 in / 943 mm Port Extension Length (EL) 21.250 in / 540 mm Tuning Frequency (Fb) 33 Hz F3 31 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

Building on the core technology of our TW5 thin-line subwoofers, the TW3’s deliver a powerful combination of shallow mounting depth and excursion capability. In fact, they are capable of a greater excursion than the W3v3’s. To allow this remarkable feat to be achieved, JL Audio’s patented thin-line woofer technology compresses the architecture of the TW3’s using a “concentric tube” structure built into the injection-moulded cone body. This structure supports the voice coil and a full annular spider while permitting the placement of the large motor structure further forward in the speaker than with conventional designs. TW3’s are optimized for small enclosures and offer our tab-ear mounting design to maximize cone area within their mounting footprints. We know you’re going to love working with these amazing subwoofer drivers. Continuous Power Handling (RMS) 400 W Recommended Amplifier Power (RMS) 200 - 400 W Nominal Impedance (Znom) Dual 4 Ω

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability. The 12W3v3-2 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 1.25 cu. ft. (35.4 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 2 Ω

This powerhouse 12-inch driver delivers potent performance and world-class sound quality in medium power applications. Several exclusive JL Audio technologies and proprietary assembly techniques are applied to the 12W3v3 to enhance linearity and reliability. The 12W3v3-4 is best used with amplifier power in the 150W - 500W range and is optimized to operate in a compact 1.125 cu. ft. (31.8 l) sealed enclosure, or a 1.75 cu. ft. (49.6 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 150 - 500 W Nominal Impedance (Znom) 4 Ω

SPECIFICATIONSContinuous Power Handling (RMS): 600 WRecommended Amplifier Power (RMS): 250 - 600 WNominal Impedance (Znom): 2 ΩNominal Diameter: 13.5 in / 345 mmOverall Diameter (A) A1: 14.2 in / 361mmA2: 13.0 in / 330 mmMounting Hole Diameter (B): 12.5 in / 318 mmBolt Hole Circle Diameter (C): 13.5 in / 343 mmMotor Outer Diameter (D): 6.75 in / 171 mmMounting Depth (E): 2.625 in / 67 mmDriver Displacement: 0.052 cu ft / 1.47 LNet Weight: 20.5 lb / 9.3 kgPARAMETERSFree Air Resonance (Fs): 25.95 HzElectrical “Q” (Qes): 0.51Mechanical “Q” (Qms): 10.648Total Speaker “Q” (Qts): 0.479Equivalent Compliance (Vas): 2.26 cu ft / 64.00 LOne-Way Linear Excursion (Xmax)*: 0.433 in / 11 mmReference Efficiency (no): 0.23%Efficiency (1 W / 1 m)**: 85.51 dB SPLEffective Piston Area (Sd): 98.26 sq in / 0.0634 sq mDC Resistance (Re): 2.100 Ω* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.

10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level. Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label General Specifications Continuous Power Handling (RMS) 1500 W Recommended Amplifier Power (RMS) 500 - 1500 W Nominal Impedance (Znom) Dual 1.5 Ω Physical Specifications Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14 in / 356 mm Mounting Hole Diameter (B) 11.9 in / 302 mm Bolt Hole Circle Diameter (C) 12.7 in / 323 mm Motor Outer Diameter (D) 8.38 in / 213 mm Mounting Depth (E) 10.5 in / 267 mm Driver Displacement 0.21 cu ft / 5.9 L Net Weight 52 lb / 23.6 kg Parameters Free Air Resonance (Fs) 23.5 Hz Electrical “Q” (Qes) 0.476 Mechanical “Q” (Qms) 7.517 Total Speaker “Q” (Qts) 0.448 Equivalent Compliance (Vas) 3.68 cu ft / 104.3 L One-Way Linear Excursion (Xmax)* 1.25 in / 32 mm Reference Efficiency (no) 0.27% Efficiency (1 W / 1 m)** 86.3 dB SPL Effective Piston Area (Sd) 107.35 sq in / 0.0693 sq m DC Resistance (Re)*** 2.41 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 1.875 cu ft / 53.1 L External Width (W) 16 in / 407 mm External Height (H) 16 in / 407 mm External Depth (D) 18.875 in / 479 mm F3 37.4 Hz Fc 40.5 Hz Qtc 0.77 Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 2.375 cu ft / 67.3 L External Width (W) 25.875 in / 657 mm External Height (H) 16 in / 406 mm External Depth (D) 17.25 in / 438 mm Internal Slot Port Width (SW) 2.25 in / 57 mm Internal Slot Port Height (SH) 14.5 in / 368 mm Internal Slot Port Length (SL) 26.25 in / 667 mm Port Extension Length (EL) 7.875 in / 200 mm Tuning Frequency (Fb) 34.6 Hz F3 30.3 Hz Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.

This subwoofer driver has been called the "best damn 8-inch subwoofer ever made" for its remarkable performance capabilities and design attributes. An impressive linear excursion envelope that exceeds 0.75 in. (19 mm) one-way allows it to deliver impact well beyond the range of other 8-inch subwoofer drivers. The 8W7AE is best used with amplifier power in the 200W - 500W range and is optimized to operate in a 0.875 cu. ft. (24.8 l) sealed enclosure, or a 1.0 cu. ft. (28.3 l) ported enclosure. Continuous Power Handling (RMS) 500 W Recommended Amplifier Power (RMS) 200 - 500 W Nominal Impedance (Znom) 3 Ω

GENERAL SPECIFICATIONSContinuous Power Handling (RMS): 600 WSystem Nominal Impedance: 2 ΩEnclosure Type: Slot-portedFinish: Gray carpetGrille Included: NoPHYSICAL SPECIFICATIONSExternal Width (W): 31.375 in / 797 mmExternal Height (H): 15.18 in / 386 mmExternal Depth (D1)L 20.3 in / 516 mmExternal Top Surface Depth (D2): 15.75 in / 400 mmNet Weight: 60.3 lb / 27.35 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on front baffle A steel mesh grille is included to protect the subwoofer driver Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 – 250W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 250 W Enclosure Type Slot-ported, Low-profile Finish Black carpet External Width (W) 18.625 in / 473 mm External Height (H) 11.0 in / 279 mm External Depth (D1) 5.125 in / 130 mm Net Weight 17.40 lb / 7.89 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 8W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure's internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with silver "JL AUDIO" embroidery on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 250WNominal Impedance: 4 Ω

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 10TW3 to deliver amazing sub-bass from an enclosure that is only 6.25 in. (159 mm) deep at its base and 4.1 in. (104 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 10TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω

In this sealed Truck PowerWedge™ subwoofer system, we harness the performance of the 12TW3 to deliver amazing sub-bass from an enclosure that is only 7 in. (178 mm) deep at its base and 4.5 in. (114 mm) at the top. This enclosure design has been carefully engineered to the optimum sealed enclosure alignment for the 12TW3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. Finish: Black, high-grade automotive carpet with "JL AUDIO" embroidered in silver on the front baffle. A steel mesh grille is included to protect the subwoofer driver. Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 100 - 400WNominal Impedance: 2 Ω  

JL Audio’s patented High Output Enclosures are designed to deliver the ultimate high-performance bass experience with a rare combination of superb sound quality and awesome output. In the HO112-W6v3, the high power handling of the 12W6v3 subwoofer driver, combined with its small enclosure requirements, results in a very compact subwoofer system that is capable of impressive output with moderate amplification. JL Audio’s patented, chamber-coupled port design (U.S. patent #6,625,292) wraps around the inner enclosure boundary and terminates just above the woofer, coupling the port output to the woofer’s direct output. This also provides the necessary surface area and port length to maximize the performance of the W6v3 driver. This enclosure design has been carefully engineered to the optimum ported alignment for the 12W6v3 and has been fine-tuned through extensive real-world listening. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. While no grille is provided, the recessed mounting baffle provides some protection for the woofer. A steel mesh woofer grille insert can be purchased separately (Model: SGR-12W6v2/v3) if additional woofer protection is desired. GENERAL SPECIFICATIONS: Finish: Dark grey, high-grade automotive carpet, with black carpet on woofer baffle “JL AUDIO” is embroidered in silver on the side surface of the enclosure Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 200 – 600W Nominal Impedance: 2 Ω Continuous Power Handling (RMS) 600 W System Nominal Impedance 2 Ω Enclosure Type Chamber-coupled, slot-ported, rear-firing design Finish Dark grey carpet with black insert Grille Included: No External Width (W) 14.5 in / 368 mm External Height (H) 16 in / 406 mm External Depth (D1) 24 in / 610 mm Net Weight 60.7 lb / 27.52 kg

This incredible MicroSub™ subwoofer system delivers the kind of output and extension that is normally possible with only much larger systems. The key to its performance lies in the precise tuning of its 6W3v3 subwoofer driver into an efficient slot-ported design. Extensive interior bracing permits the use of thinner wall material that maximizes the enclosure’s internal volume relative to its exterior volume. The port wraps around two walls of the enclosure to produce the necessary low tuning frequency that ensures excellent extension and response smoothness. The flared port entry and exit further enhance sound quality by minimizing air-flow noises through the port. This subwoofer system is shipped wired, loaded and ready to connect via a five-way binding post terminal. GENERAL SPECIFICATIONS: Finish: Black, high-grade automotive carpet with silver “JL AUDIO” embroidery on the front baffle Construction: CNC-Cut High-Grade MDF Recommended amplifier power: 50 – 150W Nominal Impedance: 4 Ω Continuous Power Handling (RMS) 150 W Enclosure Type Slot-ported, Low-profile Finish Black carpet Grille Included Black Steel Mesh External Width (W) 14.125 in / 359 mm External Height (H) 9.625 in / 245 mm External Depth (D1) 5.125 in / 130 mm Net Weight 12 lb / 5.44 kg

Purpose-built for subwoofer applications, the RD1000/1 monoblock amplifier delivers 1000 watts of jaw-dropping bass output into 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1000/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1000/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1000/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately). GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Height (H) 2.13 in / 54 mm Width (W) 14.66 in / 372 mm Depth (D) 6.96 in / 177 mm

Born to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the RD500/1 amplifier was engineered to generate tons of pure subwoofer bliss from a sleek, ultra-compact chassis. The secret behind its power proficiency is our proprietary NexD™ switching technology, which delivers large amounts of power output with precise efficiency and ultra-low distortion. For your convenience, the RD500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. With the addition of RBC-1 remote level control (sold separately), you can control the subwoofer output directly from the driver’s seat. GENERAL SPECIFICATIONS: Frequency Response 7 Hz – 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz – 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz – 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV – 2 V RMS (Low) to 800 mV – 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Height (H): 2.13 in / 54 mm Width (W): 9.78 in / 248 mm Depth (D): 6.96 in / 177 mm

The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units while retaining OEM fader control. Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed. With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to the 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs. By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine-tune the output signals. Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS). Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment. An optional DRC-100 or DRC-205 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat. Achieving great sound from your factory stereo has never been easier, or sounded better. GENERAL SPECIFICATIONS: Power Supply Type Regulated DC-DC SMPS Input Operating Voltage 10 – 16 VDC Standby Current Draw <1.5 mA Operating Current Draw 0.7 A Recommended Fuse Value 1 A Input Channels Eight Input Type Differential-Balanced Input Voltage Range 250 mV – 30 V RMS Minimum Input Voltage 10 mV RMS Input Level Setting Fully automatic Output Channels Six (Front/Rear/Sub Output Pairs) Analog Output Unbalanced, stereo RCA jacks Digital Output N/A Output Impedance 450 Ω S/N Ratio 96 dB (A-Weighted, referred to 4V RMS Output) THD+N @ Rated Output 0.02% (20 Hz – 20 kHz) Audio Resolution 24 bit / 48 kHz Number of EQ Bands 30 x 2 channels EQ Resolution 1/3 octave (25 Hz – 20 kHz) Remote Level Control Optional (DRC-100 or DRC-200) Remote Level Functions Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-205 adds Subwoofer Level Control) Height (H) 1.85 in / 47 mm Width (W) 4.29 in / 109 mm Depth (D) 6.14 in / 156 mm Net Weight 2.58 lb / 1.17 kg

JL Audio patented thin-line woofer technology compresses the architecture of the 13TW5v2 using a “concentric tube” structure that supports the 7-inch diameter voice coil and the suspension attachments. This permits placement of the large motor structure much further forward in the speaker than with conventional designs, while allowing excellent linear excursion capability and mechanical stability. To unleash even more performance from this technology, the v2 improves upon the original 13TW5 with 13% greater linear excursion capability. The cast alloy chassis has also been modified for greater strength and the redesigned motor now features an annular vent. The v2 is also available in single 2 ohm and si4-ohm4 ohm voice coil versions to fit a wide range of applications. In keeping with its “tight-spaces” mission, the 13TW5v2 is optimized for enclosures that are far smaller than most 12-inch woofers require and only a bit larger than the air space needs of a typical, small-box 10-inch woofer. The mounting system is designed to fit in about the same footprint as a typical 12-inch woofer. The 13TW5v2 is best used with amplifier power in the 250W - 600W range and is optimized to operate in a 0.80 cu. ft. (22.7 l) sealed enclosure.

The VIBE 8" BMW OEM Fit Underseat Subwoofer is designed for seamless factory integration, improved bass response, and easy plug-and-play installation, making it the perfect upgrade for BMW audio systems. Engineered with vehicle-specific baskets and wiring harnesses, this subwoofer installs directly into the original under-seat enclosure without modification. Delivering enhanced low-frequency performance, this 8 inch subwoofer provides deeper, tighter bass while maintaining clarity and balance. The system includes a high-end crossover with a reference curve setup, ensuring accurate sound reproduction and improved overall audio quality. Designed for flexibility, the system can be configured as a passive or semi-active setup, allowing compatibility with various system upgrades. Ideal for BMW factory audio upgrades, OEM integration, and improved bass performance, it delivers a noticeable enhancement in sound without compromising factory functionality. Specifications Product Type: 8" OEM Fit Underseat Subwoofer (BMW) Peak Power: 345W RMS Power: 115W (Minimum Input 55W) Sensitivity: 90dB Frequency Response: 55Hz – 25kHz Impedance: 4 Ohm Fitment: Direct OEM Replacement (Under-Seat Enclosure) Installation: Plug & Play with Vehicle-Specific Harness Crossover: High-End with Reference Curve System Type: Passive or Semi-Active Compatible Compatibility: BMW 1 Series (F20/21), 3 Series (F30/31/34/35), 4 Series (F32/33), 5 Series (F10/11), 6 Series (F12/13), X3 (F25)

The VIBE 6" x 8" Slim Active Subwoofer Enclosure is designed for compact installations, easy integration, and enhanced bass performance, making it ideal for tight spaces such as under-seat mounting. Its unique size and slim profile allow it to fit where traditional subwoofers cannot, without compromising sound quality. Built with a durable cast aluminium chassis, this enclosure offers strength while keeping weight to a minimum. The sealed (acoustic suspension) design ensures tight, controlled bass response, perfect for improving low-end performance in factory or aftermarket systems. Featuring high-level input with Auto Sense technology, the amplifier automatically powers on and off without the need for a remote turn-on wire. The included wired remote control allows convenient adjustment of subwoofer output from the driver’s seat. Perfect for stealth installs, OEM upgrades, and compact car audio systems, this slim active enclosure delivers efficient and controlled bass in a space-saving design. Specifications Product Type: Slim Active Subwoofer Enclosure Subwoofer Size: 6" x 8" RMS Power: 80W Peak Power: 240W Impedance: 4 Ohm Driver: Pulse 68 Enclosure Type: 2nd Order Acoustic Suspension (Sealed) Amplifier: Built-In Technology: Auto Sense Turn-On Control: Wired Remote Bass Controller Construction: Cast Aluminium Chassis Dimensions: 72mm (H) x 290mm (W) x 210mm (D)

The VIBE PULSE 12" Subwoofer is designed to deliver powerful bass performance at an affordable price, making it the perfect choice for entry-level car audio upgrades. Combining VIBE’s proven engineering with cost-effective design, this subwoofer offers impressive low-frequency output without compromising quality. Featuring a wide roll butyl foam surround, the PULSE subwoofer allows greater cone excursion for deeper and more impactful bass. The reinforced PP dome dustcap and harmonised design of the voice coil, spider, cone, and magnet ensure accurate bass reproduction with improved durability. Equipped with a high-temperature single 4 ohm voice coil, this subwoofer offers flexible compatibility with a wide range of amplifiers, including bridged multi-channel setups. Perfect for budget-friendly builds, first-time upgrades, and everyday bass systems, the PULSE series delivers reliable performance and strong output. Specifications Subwoofer Type: 12" Subwoofer Configuration: Single 4 Ohm RMS Power: 350W Peak Power: 1050W Frequency Response: 25Hz – 850Hz Voice Coil: 1.5" OFC High Temperature Surround: Butyl Foam Surround Dustcap: PP Dome Spider: Poly Cotton Design: Bumped Backplate for Increased Excursion Mounting Depth: 142mm (5.6") Mounting Diameter: 277mm (10.9")

The VIBE SLICK C10 10" Ultra Slim Underseat Subwoofer is designed for powerful bass in tight spaces, making it the perfect solution for vehicles where installation space is limited. With an ultra-slim depth of just 75mm, this compact subwoofer fits easily under seats while still delivering impressive low-frequency performance. Built with a rigid cast aluminium enclosure, the SLICK C10 minimises resonance and maximises energy efficiency, ensuring clean and controlled bass output. The specially engineered 10 inch woofer is optimised for shallow installations, delivering dynamic and punchy bass despite its compact size. Featuring high and low-level inputs along with Auto Sense turn-on, this subwoofer integrates seamlessly with both factory and aftermarket systems. The included bass controller allows easy adjustment of output levels, giving you full control over your sound. Perfect for underseat installations, compact car audio upgrades, and stealth bass systems, the SLICK C10 offers performance without compromise. Specifications Product Type: 10" Underseat Active Subwoofer Power Handling: 180W RMS / 540W Peak Subwoofer Size: 10" Installation Depth: 75mm (Ultra Slim) Enclosure: Cast Aluminium (Low Resonance Design) Inputs: High Level & Low Level Technology: Auto Sense Turn-On Control: Included Bass Level Controller Application: Underseat / Compact Installations

The VIBE SLICK8D2-V0 8" Dual 2 Ohm Subwoofer is engineered for powerful bass, high excursion, and precision performance, making it one of the strongest entry-level subwoofers in its class. Built with an upgraded motor structure and advanced components, it delivers deep, controlled low-frequency output with impressive efficiency. Featuring a high-temperature 2" (50mm) 4-layer dual voice coil and a large magnet assembly, this subwoofer provides increased power handling and improved control. The semi-pressed composite paper cone combined with a wide roll foam surround allows greater excursion, producing deeper bass with excellent accuracy. Designed with VIBE’s torsion basket and reinforced spider assembly, the SLICK8D2-V0 ensures durability and consistent performance under demanding conditions. Perfect for car audio upgrades, compact bass builds, and high-output systems, it delivers a balance of power, precision, and reliability. Specifications Model: SLICK8D2-V0 Subwoofer Type: 8" Subwoofer Configuration: Dual 2 Ohm RMS Power: 450W Peak Power: 1350W Max SPL (Burst): 2700W Voice Coil: 2" (50mm) 4-Layer High Temperature Cone: Composite Paper Cone Surround: Wide Roll Foam Surround Basket: VIBE Torsion Basket Design Application: High Excursion / Deep Bass Systems

The VIBE SLICK V12 Dual 12" Slim Bass Enclosure is engineered for powerful bass output in a compact, space-saving design, making it ideal for vehicles with limited installation depth. Delivering performance comparable to larger enclosures, the SLICK V12 achieves deep, punchy bass while being over 30% slimmer than traditional designs. Equipped with dual 12 inch subwoofers and dual voice coil configuration, this enclosure offers flexible wiring options and broad amplifier compatibility. The built-in amplifier docking system allows easy integration of the POWERBOX400.1M amplifier, enabling a quick upgrade from passive to active setup. Designed with a trapezoid enclosure structure, the SLICK V12 maximises internal efficiency while maintaining durability and consistent bass performance. Perfect for car audio upgrades, shallow installs, and high-output bass systems, it delivers strong low-frequency response without compromising space. Specifications Product Type: Dual 12" Slim Passive Bass Enclosure Subwoofers: 2 x 12" Drivers Peak Power: 2400W RMS Power: 800W Impedance: Dual 2 Ohm Enclosure Type: Trapezoid Bass Enclosure Design: Slim / Space-Saving (Shallow Mount Friendly) Compatibility: Amplifier Docking System (POWERBOX400.1M-V7 Compatible) Application: Passive (Convertible to Active)

The VIBE SLICK V12 Single 12" Passive Bass Enclosure is designed for powerful bass performance in a compact, space-saving design, making it ideal for vehicles with limited installation depth. Delivering strong low-frequency output, this enclosure offers the performance of larger systems in a slimmer profile. Featuring a single 12 inch subwoofer with dual voice coil configuration, this enclosure provides flexible wiring options and compatibility with a wide range of amplifiers. The integrated amplifier docking system allows easy installation of the POWERBOX400.1M amplifier, enabling quick conversion from passive to active setup. The hybrid vent design combines a slot port with flared turboports to maximise airflow and bass efficiency, delivering deeper and more controlled low frequencies. Compatible with the Rapid Fit kit, installation can be simplified without the need to run power cables directly to the battery (active setup only). Perfect for car audio upgrades, compact installs, and high-performance bass systems, the SLICK V12 offers a balance of power, flexibility, and convenience. Specifications Product Type: Single 12" Passive Bass Enclosure Subwoofer: 1 x 12" Driver Peak Power: 1200W RMS Power: 400W Impedance: Dual 2 Ohm Enclosure Type: Trapezoid Bass Enclosure Vent Design: Hybrid Slot Port with Flared Turboports Compatibility: Amplifier Docking System (POWERBOX400.1M-V7 Compatible) Installation: Rapid Fit Kit Compatible (Active Setup) Application: Passive (Convertible to Active)

The VIBE SLICK 12" Dual 2 Ohm Subwoofer is engineered for powerful bass, increased excursion, and improved efficiency, making it one of the strongest performers in its class. Designed with a larger motor structure and enhanced components, this subwoofer delivers deep, controlled low-frequency output with excellent reliability. Featuring a high-temperature 2" (50mm) 4-layer dual voice coil and FEMM motor design, this subwoofer offers increased power handling and improved magnetic control for better accuracy and output. The semi-pressed composite FEA cone combined with a wide-roll stitched foam surround ensures strong bass response with high durability and smooth excursion. Built with VIBE’s torsion basket and a reinforced spider assembly, the SLICK subwoofer delivers greater movement and efficiency, producing deeper bass with precision. Ideal for car audio upgrades, bass-focused systems, and everyday high-output setups, it offers a balance of power, performance, and value. Specifications Subwoofer Type: 12" Subwoofer Configuration: Dual 2 Ohm RMS Power: 500W Peak Power: 1500W Frequency Response: 25Hz – 850Hz Voice Coil: 2" (50mm) 4-Layer Dual Voice Coil Motor: FEMM Optimised Motor Surround: Butyl Foam Surround Dustcap: PP Dome Spider: Poly Cotton Terminals: Spring Loaded Design: Bumped Backplate for Increased Excursion Mounting Depth: 147mm (5.8") Mounting Diameter: 277mm (10.9")

Take your car audio system to the next level with the Sony XS-W124GS 12" component subwoofer. Engineered for deep, powerful bass, this subwoofer delivers clear low-frequency performance that brings your music to life. Built with a durable paper cone, polypropylene dust cap, rubber surround, and steel basket, it’s designed for long-lasting performance even under heavy use. Whether installed in a sealed or ported enclosure, the XS-W124GS provides precision bass, excellent sensitivity, and reliable power handling for audiophiles and enthusiasts alike. Backed by a 3-year warranty, it’s the perfect addition to elevate your in-car listening experience. Category Specification / Feature General 12" 4-ohm component subwoofer, paper cone w/ polypropylene dust cap, rubber surround, steel basket, grille not included, free-air: No, dual voice coil: No, Parts & Labor Warranty: 3 Years, Returns: 60 Days Power Handling Max RMS: 420W, Peak Power: 1800W Frequency & Sensitivity Frequency Response: 30–500 Hz, Sensitivity: 83 dB @ 1W Dimensions Top Mount Depth: 5.625", Bottom Mount Depth: 5.9375", Cutout Diameter: 10.813", Frame Width/Length: 12.694" Enclosure Compatibility Sealed Box: 0.72–1.2 cu ft (ideal 0.91 cu ft), Ported Box: 0.92–1.6 cu ft (ideal 1.16 cu ft, port 3.625" diameter x 13.875" length) Thiele/Small Parameters Vas: 49.1949 L, Fs: 31.9 Hz, Qts: 0.674, Xmax: 7.8 mm Included in Package One 12" single voice coil woofer, plastic trim ring, adhesive-backed foam gasket, eight 1-3/8" screws, instructions (EN/FR/ES), warranty info

Upgrade your in-car audio with the Sony XS-AW8 compact powered under-seat subwoofer. Designed to fit discreetly under your seat, this 8" subwoofer delivers deep, controlled bass without taking up valuable cabin space. Featuring a Class A/B 75-watt amplifier, sealed cast-aluminum enclosure, and versatile line- and speaker-level inputs, the XS-AW8 provides clear and powerful low-end performance for any music genre. With a wired remote for easy level adjustments, flexible mounting brackets, and simple plug-and-play installation, it’s perfect for enhancing your car audio experience with minimal effort. Backed by a 1-year warranty, this subwoofer combines convenience, quality, and reliability in a compact package.   Category Specification / Feature General Compact powered under-seat subwoofer, 8" shallow-profile woofer, sealed cast-aluminum enclosure, wired remote included, speaker- and preamp-level inputs, steel grille, connector type: RCA/Harness, Parts & Labor Warranty: 1 Year, Returns: 60 Days Amplifier Class A/B, RMS Power: 75 watts, Maximum Wattage: 160 watts Audio Crossover: Low pass 50–150 Hz, Phase: Normal/Reverse switch, Impedance: N/A, Sensitivity: N/A Dimensions Length: 13-5/8", Width: 9-7/8", Height: 3-1/8" (mounting brackets add 1⅜" width / 1⅝" depth) Inputs Line level RCA, speaker-level input, wired remote control with 13' cord, power wire: 13' (14-gauge), ground wire: 13' (14-gauge), remote turn-on: 10', speaker input: 10' Mounting Four corner mounting brackets, remote bracket with adhesive pad, screws included (M5x8mm, 3/4", 1/2", 3/16") Package Contents Powered subwoofer, wired remote control, wiring harness, mounting brackets, remote mounting bracket with pad, screws (various), printed wiring instructions, warranty information