All 4WD Parts and Accessories

SPECIFICATIONSContinuous Power Handling (RMS): 600 WRecommended Amplifier Power (RMS): 250 - 600 WNominal Impedance (Znom): 2 ΩNominal Diameter: 13.5 in / 345 mmOverall Diameter (A) A1: 14.2 in / 361mmA2: 13.0 in / 330 mmMounting Hole Diameter (B): 12.5 in / 318 mmBolt Hole Circle Diameter (C): 13.5 in / 343 mmMotor Outer Diameter (D): 6.75 in / 171 mmMounting Depth (E): 2.625 in / 67 mmDriver Displacement: 0.052 cu ft / 1.47 LNet Weight: 20.5 lb / 9.3 kgPARAMETERSFree Air Resonance (Fs): 25.95 HzElectrical “Q” (Qes): 0.51Mechanical “Q” (Qms): 10.648Total Speaker “Q” (Qts): 0.479Equivalent Compliance (Vas): 2.26 cu ft / 64.00 LOne-Way Linear Excursion (Xmax)*: 0.433 in / 11 mmReference Efficiency (no): 0.23%Efficiency (1 W / 1 m)**: 85.51 dB SPLEffective Piston Area (Sd): 98.26 sq in / 0.0634 sq mDC Resistance (Re): 2.100 Ω* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”.

GENERAL SPECIFICATIONS Continuous Power Handling (RMS): 300 WSystem Nominal Impedance: 4 ΩEnclosure Type: Slot-portedFinish: Gray carpetGrille Included: No PHYSICAL SPECIFICATIONSExternal Width (W) 16.31 in / 414 mmExternal Height (H) 15.18 in / 386 mmExternal Depth (D1) 20.3 in / 516 mmExternal Top Surface Depth (D2) 15.75 in / 400 mmNet Weight 33.1 lb / 15 kg

JL AUDIO JL AUDIO JD400/4 400W RMS JD SERIES CLASS-D 4-CHANNEL AMPLIFIER Premium Engineering Utilizing our exclusive NexD™ high-speed switching technologies, the JD400/4 amplifier is engineered to deliver loads of clean power, with excellent efficiency and low distortion. This little guy churns out 100 watts of audio from each of its four channels into 2 ohms (14.4V, 1% THD) and is fully bridgeable, so it can be used as a 3-channel amplifier, or as a 2-channel amplifier producing a whopping 200W x 2 into 4 ohms. The JD400/4’s controls can be found on the input panel of the amplifier, with all speaker and power connections located along the opposite end of the extruded aluminum chassis. Signal processing features include high or low-pass 12 dB / octave filters (defeatable) for each channel pair, with continuously variable frequency selection from 50-500 Hz, and dual-range, differential-balanced inputs capable of accepting line-level or speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard equipment. Onboard LED-clipping indicators are also included surrounding each input sensitivity control. This convenient feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. You will also find a set of buffered, pass-through preamp outputs on-board, so you can pass signals to another amplifier. NexD Switching Technology Let's get a little nerdy... A traditional PWM switching amp design uses a fixed switching frequency and varies the pulse width based solely on the audio input signal to the pulse modulator. This basic approach assumes some ideal conditions, like a rock-steady power supply, that do not necessarily occur in a real, in-car installation. Power supply sag with signal causes distortion at all power levels with these designs, even well below clipping. The cure for this is feedback (a corrective signal sent back to the input side), but this becomes impractical as the audio frequency increases, making it a good solution for band-limited (subwoofer) amps, but not for full-range amplifiers. Taking the above into account when designing the NexD™ subwoofer amplifiers, we have taken the simple fixed PWM approach and enhanced it with a very high switching frequency: 240 kHz, which is about 4x higher than most Class D subwoofer amplifiers. This pushes the amplifier's bandwidth to at least 500 Hz with minimal distortion and improves efficiency, while keeping typically bulky circuity more compact. Your subwoofers will reward you with tight, rock-solid bass performance. For the full-range NexD™ amplifiers and channels we applied a variable, ultra-high speed version of the NexD™ technology (switching at well over 400 kHz). In these designs, a self-oscillating modulator with "feed-forward" sends information about the instantaneous power supply voltage to the modulator, combining this with the input signal to cancel out any distortion due to supply voltage fluctuation. This reduces distortion prior to applying feedback, simplifying the overall feedback loop design. Differential-Balanced Inputs Today’s vehicles are equipped with sophisticated electronics capable of generating noise and interference that can intrude into the audio path, ruining the listening experience. Most audio equipment uses single-ended, ground-referenced RCA jacks to receive audio signals. This means that the RCA shield is connected directly to the signal ground. This is a simple, cost-effective input design that works well for short runs in noise-free environments. In noisier environments, this method cannot reject the common mode noise that could be on both RCA conductors (shield and center conductor). By having more than one chassis-grounded RCA shield on a device, single-ended input designs are also more susceptible to ground loops. If noise is present on both conductors while the shield is connected to ground, the input amplifier will amplify the noise relative to the grounded RCA shield. When there are multiple RCA connections or any other conductors subjected to a magnetic field, this will cause a difference in potential across the RCA loop to be amplified at the grounded RCA as noise (a classic ground loop). JL Audio’s Differential-Balanced Input circuits measure the center pin of the RCA connection relative to the RCA shield, even when the shield is not connected to ground, and even when the voltages at both conductors are moving relative to ground. Because both the center conductor and the shield see high impedance to ground at the input, a ground loop cannot be formed, as there is no current flow to induce a voltage as noise. This works equally well with differential-balanced, or unbalanced signal sources, making this input architecture compatible with all standard car and marine audio equipment, using standard, unshielded, twisted-pair RCA cables. No special cables are required, unlike the fully balanced connections used in professional audio. Another benefit of the Differential-Balanced Input design is that it easily accepts low-level and high-level signals from a variety of factory head unit outputs and amplifiers, including single-ended “ground referenced” sources, as well as Balanced or Unbalanced “Bridged or BTL” sources. This eliminates the need for Line Output Converters (LOCs) in most installation scenarios. The obvious question is: “Why don’t all car audio amplifiers use Differential-Balanced Inputs?” The answer is simple: it costs more. Executing a proper differential-balanced input section requires more components and better quality components than a basic single-ended design, so you generally won’t find them on less expensive amplifiers. Product Details: JD Series Class D 2 ohms Stable 4-Channel Amplifier RMS Power Rating: 4 ohms: 75 watts x 4 channel 2 ohms: 100 watts x 4 channel Bridged: 200 watts x 2 channel @ 4 ohms Total power output: 400 watts LED Power/Protect Light Wired bass level remote control not included Speaker-level (high-level) inputs (Requires adapter like the JL Audio XD-CLRAIC2-SW) Signal sensing remote turn-on Protection Circuitry with Status LED NextD™ switching amp technology Differential-balanced inputs help eliminate noise Advanced Rollback Protection System prevents thermal shut-down Speaker-level (high-level) inputs Input sensitivity: Low level: 200mV - 2 volts High level: 800mV - 8 volts Frequency Response: 12 - 22000 Hz Total Harmonic Distortion (THD): >1% Signal to Noise Ratio: >104 dB Variable high-pass filter: 50 - 500 Hz Variable low-pass filter: 50 - 500 Hz Fuse Rating: 40A 4 AWG gauge amplifier wiring kit is recommended for installation Dimensions: 9-7/8" L x 7-1/2" W x 2-1/8" H Authorized Internet Dealer 2 Year Manufacturer's Warranty MFR #: JD400/4 Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer

JL AUDIO MICROSUB CP110LG-TW1-2 300 WATT RMS SINGLE 10" 10TW1-2 SUBWOOFER Product Highlights • Preloaded with single 10TW1-2 Subwoofer• Nominal Impedance: 2-ohms• Black, high-grade automotive carpet with silver embroidery• Efficient slot-ported design and precise tuning of its 10TW1 subwoofer• Sensitivity: 82.2 dB 1 watt / 1 meter General Features: Single 10" Vented Subwoofer Enclosure Preloaded with single 10TW1-2 Subwoofer RMS Power Rating: RMS: 300 watts Recommended power range: 75 - 300 watts RMS Nominal Impedance: 2 Ω Extensive interior bracing Steel mesh grille included Black, high-grade automotive carpet with silver embroidery Flared port entry and exit for enhanced sound quality Five-way binding post terminals for easy installation Precision-built in USA at JL Audio’s Miramar, Florida factory Long linear excursion capability (0.40 in / 10 mm, one-way) Efficient slot-ported design and precise tuning of its 10TW1 subwoofer Matching JL Audio Amplifier: JL Audio JX250/1 JL Audio XD300/1v2 - ✔ Preferred Match Authorized Internet Dealer 2 Year Manufacturer's Warranty General Specifications: Injection molded, mica-filled polypropylene cone Rubber surround No pole vent: permits mounting close to rear wall of enclosure DMA-optimized motor design Patented concentric tube architecture Patented floating cone attach method technology Cast alloy frame with flat edges for tight driver grouping Construction: CNC-Cut High-Grade MDF One-Way Linear Excursion (Xmax): 0.40 in / 10.0 mm Sensitivity: 82.2 dB 1 watt / 1 meter Enclosure Dimensions: 6.375" D x 20.875" W x 13.250" H Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer Item Details Manufacturer: JL AUDIO Model Number: CP110LG-TW1-2 Weight: 25.25lbs Internal SKU: cp110lgtw12

JL AUDIO CS113TG-TW5V2SINGLE 13TW5V2 TRUCK POWERWEDGE, SEALED, 2 Product highlights • 13.5" Loaded PowerWedge Truck Enclosure• 1200W Peak• 600W RMS• Comes Equipped with One JL Audio 13TW5-3v2 TW5 Thin-Line Subwoofer• High Grade Black Carpet Finish• Five-Way Binding Post Connectors Product Features:         13-1/2" TW5 (Thin-Line) Series Shallow Mount Subwoofer Power Handling: RMS: 600 watts Recommended Power Range: 250 - 600 watts Impedance: 2-Ohm Mica-filled polypropylene cone Santoprene surround Cast alloy basket 7-inch diameter voice coil Unique design allows for small airspace requirements Requires only 0.8 cubic feet of airspace 13% greater linear excursion capability over previous model Redesigned motor features an annular vent DMA-optimized motor designs   Patented floating cone attach method" technology Patented concentric tube architecture "Tab-Ear" frame design to fit driver in tight spaces Precision-built in USA at JL Audios Miramar, Florida factory Sensitivity: 85.63 dB Xmax: 11 mm Reference Efficiency (no): 0.2300% Frequency response: ~20 ~ 200 Hz Matching Amplifiers: JL Audio XD600/1v2 JL Audio 600/1v3 Authorized Internet Dealer 2 Year Manufacturer's Warranty General Enclosure Features: PowerWedge Sealed Truck Enclosure V-Groove MDF Construction advanced cabinet-building technique uses CNC machining to create precise panel joints Delivers world-class sub-bass fidelity Provides a detailed and smooth response High grade black carpet finish Five-Way binding post connectors Embroidered JL Audio logo JL Audio ECS internal wiring Steel mesh grille provides excellent woofer protection Designed to fit perfectly behind the seats of trucks Final Impedance: 2 ohm Weight: 34 lbs Dimensions: 4-1/2"TD x 7-1/4"BD x 21-1/4"W x 15-3/4"H Warranty and Return Policy Parts Warranty Duration 2 years Labor Warranty Duration 2 years Warranty Provider Manufacturer

JL AUDIO SB-TE-YG1/10TW1 TESLA MODEL Y STEALTHB OVERVIEW Tesla’s popular compact crossover delivers quick acceleration and a roomy cabin with plenty of space for both people and cargo. Sadly though, the factory audio options offer very little to satisfy in the bass reproduction departmen 10TW-1 SUBWOOFERS Featuring an all-fiberglass, custom-formed, sealed enclosure, this Stealthbox® houses an innovative. 10-inch TW1 thin-line subwoofer. Designed to drop into the driver’s side, rear storage compartment, this Stealthbox® solution produces amazing amounts of deep bass output, while practically vanishing into its surroundings. BUILT IN USA At a time when most audio products are built overseas, JL Audio’s commitment to in-house loudspeaker production continues to grow. To pull this off in a competitive world market, our production engineering team has created one of the world’s most advanced loudspeaker assembly facilities and established a global network of quality component suppliers who build to our specifications. This, combined with our commitment to state-of-the-art assembly technology, allows our skilled workforce to efficiently build JL Audio products to extremely high quality standards, right here in the U.S.A. INSTALL NOTES Use of driver's side, rear storage compartment is lost with installation. SPECIFICATIONS 2020-UP TESLA MODEL Y (5-SEAT) SUBWOOFERS 10TW1-2 POWER 300W RMS NOMINAL IMPEDANCE 2Ω MONO FEATURES BRAND JL AUDIO RMS POWER 300W RMS SHALLOW MOUNT YES SUBWOOFER SIZE 10"  

JL AUDIO CS110LG-TW3 SINGLE 10TW3 POWERWEDGE, SEALED, 2 Ω Product highlights • Peak Power Handling: 800W • RMS Power Handling: 400W • Dual 4 Ohm Voice Coils • Sealed Enclosure w/ Black Carpet Finish • 5/8" MDF Construction Subwoofer Features: 10" 2 ohm TW3 subwoofer driver Power Handling: Peak: 800 watts RMS: 400 watts Impedance: 2 ohms Mica-filled injection molded polypropylene cone Rubber woofer surround Dual 4 ohm voice coils Frequency response: 22-200 Hz Sensitivity: 82dB Comes with black steel mesh grille 2 Year Manufacturer's Warranty General Enclosure Features: Subwoofer mounting depth: 3-1/2" Subwoofer cutout diameter: 11-5/8" 5/8" MDF construction Sealed enclosure Black carpet covered cabinet One pair of 5-way binding posts on the left side of the enclosure Nickel plated push terminals Dimensions: 5-1/8"D x 6-5/8"D w/ grille x 21"W x 15-3/8"H

Monoblock Class D Subwoofer Amplifier, 500 W x 1 @ 2 Ω / 250 W x 1 @ 4 Ω - 14.4V Designed to produce a whopping 500 watts into 2 ohms (14.4V, 1% THD), the JD500/1 amplifier is a great solution for powering subwoofers in a cost-conscious system. Our proprietary NexD™ switching technology delivers large amounts of real-world power output with excellent efficiency and ultra-low distortion. The JD500/1’s controls are located on the input panel. while the power and speaker connections can be found along the opposite end of its extruded aluminum chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balanced inputs are also on-hand, capable of accepting line-level and speaker-level signals. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier.  The JD500/1 is also equipped with an onboard LED-clipping indicator ring, surrounding the input sensitivity control. This useful feature lets you set your amplifier’s input sensitivity, quickly and accurately, without special equipment. With the addition of an RBC-1 remote level control (sold separately), you can control the subwoofer level from the driver’s seat.   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 250 W RMS x 1 @ 3 Ω 350 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 225 W RMS x 1 @ 3 Ω 300 W RMS x 1 @ 2 Ω 400 W RMS x 1 @ 1.5 Ω N/A   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >80 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >60 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™)   Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.10 in / 53 mm Width (W) 9.50 in / 242 mm Depth (D) 7.50 in / 190 mm Net Weight

Monoblock Class D Subwoofer Amplifier, 1500 W x 1 @ 1 - 2 Ω / 750 W x 1 @ 4 Ω - 14.4V Engineered for high-power, subwoofer applications, the RD1500/1 monoblock amplifier is built to deliver staggering amounts of world-class bass output. Equipped with a special low impedance circuit, the RD1500/1 is capable of generating a whopping 1500 watts of output power, at either 1 or 2 ohms (14.4V, 1% THD). At the heart of this ultra-sleek and compact power plant is JL Audio’s exclusive NexD™ Class D technology, permitting high power output with exceptional efficiency and low distortion. For your convenience, all of the RD1500/1’s controls are located on top of the amplifier, beneath a protective cover, with all connections found along one side of its chassis. Signal processing features include a 12 dB / octave low-pass filter, with continuously variable frequency selection from 50-500 Hz, and a variable bass boost EQ. Dual-range, differential-balance inputs are also onboard, capable of accepting most input voltage levels. Automatic turn-on capability (via signal sensing or DC-offset sensing) is standard, along with a set of preamp outputs so you can easily pass signals to another amplifier. The RD1500/1 is also equipped with an onboard LED-clipping indicator. This all-new, innovative feature lets you easily set your amplifier’s input sensitivity setting, quickly and accurately, with no special equipment needed. The RD1500/1 features a durable, black powder-coated finish and a top-mounted, dual-color LED light strip that reports the overall status and condition. Control of the subwoofer level from the driver’s seat is easily accomplished with the addition of the optional RBC-1 remote level control (sold separately).   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1500 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 750 W RMS x 1* @ 3 Ω 1000 W RMS x 1* @ 2 Ω 1200 W RMS x 1* @ 1 Ω 1500 W RMS x 1** *Requires “Low Z” switch to be in “2Ω” position**Requires “Low Z” switch to be in “1Ω” position   General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >82 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >50 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1100 / 50 Hz Damping Factor @ 2 Ω >550 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs Switchable from 200 mV - 2 V RMS (Low) to 800 mV - 8 V RMS (High) Min.Copper Power / Ground Wire Gauge 2 AWG wire Fuse Rating 150A (AFS or AGU)   Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer No Filter Defeat Function No Infrasonic Filter No Bass Boost EQ Yes Output Polarity Switch No Remote Subwoofer Level Control Optional (RBC-1) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered   Physical Specifications Height (H) 2.13 in / 54 mm Width (W) 18.05 in / 458 mm Depth (D) 6.96 in / 177 mm Net Weight

2-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 2 @ 2 Ω / 75 W x 2 @ 4 Ω - 14.4V The tiny XDM200/2 packs a serious full-range punch, delivering a staggering 100 watts per channel into 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM200/2 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM200/2 includes a 12 dB / octave filter which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 75 W RMS x 2 @ 2 Ω 100 W RMS x 2 Bridged @ 4Ω 200 W RMS x 1 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 2 @ 2 Ω 90 W RMS x 2 Bridged @ 4Ω 180 W RMS x 1 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS  Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 20 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Security Cover for Controls Yes Pass-Through Preamp Output Buffered Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 6.85 in / 174 mm Depth (D) 7.09 in / 180 mm Net Weight 3.75 lb / 1.70 kg

4-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 4 @ 2 Ω / 75 W x 4 @ 4 Ω - 14.4V   The ultra-compact XDM400/4 packs a serious full-range punch, generating a whopping 100 watts to each of its four channels into 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM400/4 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Combine the XDM400/4 with our XDM600/1 monoblock to build a stunning 1000 W amplification system to power four satellites and a subwoofer... and fit the whole thing under a seat or deck. Or, use the XDM400/4 by itself to power two satellites, plus a subwoofer.  The XDM400/4 includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the rear channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 75 W RMS x 4 @ 2 Ω 100 W RMS x 4 Bridged @ 4Ω 200 W RMS x 2 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 4 @ 2 Ω 90 W RMS x 4 Bridged @ 4Ω 180 W RMS x 2 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 40 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or All channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered Source Channel Selection for PreOuts Yes Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 6.3 lb / 2.86 kg

3-Channel Class D Car/Marine System Amplifier, 75 W x 2 @ 4 Ω + 300 W x 1 @ 2 Ω - 14.4V Small enough to fit in just about any tight space application, the XDM500/3 is the perfect amplifier for a simple audiophile-grade, subwoofer / satellite system. With its three channels of versatile output, you can drive a pair of quality component speaker systems with plenty of clean power, while also delivering a stout 300 W to your subwoofer system. The technology that makes this much power possible in such a small chassis is our advanced NexD™ switching amplifier design. Suitable for car or boat installations, the XDM500/3 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM500/3 includes a 12 dB / octave high-pass filter for its main channels, plus a variable slope low-pass filter for its subwoofer channel. Both filters offer continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V Main Channels @ 4 Ω 75 W RMS x 2 Main Channels @ 2 Ω 100 W RMS x 2 Main Channels - Bridged @ 4Ω 200 W RMS x 1 Subwoofer Channel @ 4 Ω 180 W RMS x 1 Subwoofer Channel @ 3 Ω 240 W RMS x 1 Subwoofer Channel @ 2 Ω 300 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V Main Channels @ 4 Ω 60 W RMS x 2 Main Channels @ 2 Ω 90 W RMS x 2 Main Channels - Bridged @ 4Ω 180 W RMS x 1 Subwoofer Channel @ 4 Ω 180 W RMS x 1 Subwoofer Channel @ 3 Ω 240 W RMS x 1 Subwoofer Channel @ 2 Ω 300 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A General Specifications Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >120 / 50 Hz Damping Factor @ 2 Ω >60 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 500 Hz Filter Mode(s): Channels 3 & 4 (rear) N/A Filter Slope(s): Channels 3 & 4 (rear) N/A Filter Frequency Range: Channels 3 & 4 N/A Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4 ch.) Pass-Through Preamp Output Buffered

Monoblock Class D Car/Marine Subwoofer Amplifier, 600 W x 1 @ 2 Ω / 400 W x 1 @ 4 Ω - 14.4V This potent monoblock amplifier employs our high-speed NexD™ switching design to achieve unprecedented efficiency and amazing power output from a very compact chassis. Don't let its small size fool you, though... the XDM/600/1 generates serious subwoofer power, delivering a full 600 W of continuous power into a 2 ohm load (14.4V, 1% THD). Designed for car or boat installations, the XDM600/1 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. Targeted specifically for subwoofer applications, the XDM600/1 includes a variable slope low-pass filter with continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), the amplifier's level can be adjusted directly from the driver's seat or captain’s chair. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. Rated Continuous (RMS) Power @ 14.4 V   @ 4 Ω 400 W RMS x 1 @ 3 Ω 500 W RMS x 1 @ 2 Ω 600 W RMS x 1 @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 300 W RMS x 1 @ 3 Ω 400 W RMS x 1 @ 2 Ω 500 W RMS x 1 @ 1.5 Ω N/A General Specifications Frequency Response 7 Hz - 500 Hz (+0, -1dB) S/N Ratio, referred to highest rated power >87 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >67 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >1000 / 50 Hz Damping Factor @ 2 Ω >500 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass only Filter Slope(s) 12/24 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometer Yes Filter Defeat Function Yes Infrasonic Filter 30 Hz, defeatable Bass Boost EQ No Output Polarity Switch No Remote Subwoofer Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Bass EQ Boost Control No Pass-Through Preamp Output Buffered Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 8.52 in / 216 mm Depth (D) 7.09 in / 180 mm Net Weight 6.3 lb / 2.86 kg

6-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 6 @ 2 Ω / 75 W x 6 @ 4 Ω - 14.4V   The incredibly flexible XDM600/6 packs a serious full-range wallop and delivers a stunning 100 watts to each of its six channels into 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM600/6 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. With the XDM600/6, you have plenty of great use options. Configure it as a six-channel satellite amplifier with 75 W x 6 @ 4 Ω, or bridge four of its channels to create a staggered power four-channel amplifier with 200 W x 2 @ 4 Ω for your front satellites and 75 W x 2 @ 4 Ω for your rear satellites. You can also drive two subwoofers with 200 W each, plus a pair of satellites with 75W x 2. The XDM600/6 includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all six amplifier channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 75 W RMS x 6 @ 2 Ω 100 W RMS x 6 Bridged @ 4Ω 200 W RMS x 3 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 6 @ 2 Ω 90 W RMS x 6 Bridged @ 4Ω 180 W RMS x 3   General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 50 A (AFS, AGU or MaxiFuse™)   Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or 4 or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A   Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 5.8 lb / 2.63 kg

5-Channel Class D Car/Marine System Amplifier, 75 W x 4 @ 4 Ω + 300 W x 1 @ 2 Ω - 14.4V    The XDM700/5 is ideal for a complete audiophile-grade, subwoofer + four satellite system, and fits comfortably in just about any vehicle or vessel. With this incredible little amplifier, you can drive two pairs of quality component speaker systems with plenty of clean power (75 W x 4 @ 4 Ω), while also generating a solid 300 W of power for a subwoofer system. The technology that makes this much power possible in such a small chassis is our high-speed NexD™ switching amplifier design. Suitable for car or boat installations, the XDM700/5 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM700/5 includes a 12 dB / octave high-pass filter for one main channel pair, a 12 dB octave high-pass or bandpass filter for the other main channel pair, plus a variable slope low-pass filter for its subwoofer channel. All three filters offer continuously variable cutoff frequency selection from 50-500 Hz. This amplifier's filters can also be configured as a true 3-way crossover, with a low-pass filter for the subwoofer channel, a bandpass filter on Ch. 3 & 4, and a high-pass filter on Ch. 1 & 2. An "x10" multiplier switch on the Ch. 1 & 2 high-pass filter allows its cutoff frequency to be adjusted from 50-500 Hz or 500-5000 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of all amplifier channels or just the subwoofer channel directly from the driver's seat or helm. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.   Rated Continuous (RMS) Power @ 14.4 V Main Channels @ 4 Ω 75 W RMS x 4 Main Channels @ 2 Ω 100 W RMS x 4 Main Channels - Bridged @ 4Ω 200 W RMS x 2 Subwoofer Channel @ 4 Ω 180 W RMS x 1 Subwoofer Channel @ 3 Ω 240 W RMS x 1 Subwoofer Channel @ 2 Ω 300 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A Rated Continuous (RMS) Power @ 12.5 V   Rated Continuous (RMS) Power @ 12.5 V Main Channels @ 4 Ω 60 W RMS x 4 Main Channels @ 2 Ω 90 W RMS x 4 Main Channels - Bridged @ 4Ω 180 W RMS x 2 Subwoofer Channel @ 4 Ω 180 W RMS x 1 Subwoofer Channel @ 3 Ω 240 W RMS x 1 Subwoofer Channel @ 2 Ω 300 W RMS x 1 Subwoofer Channel @ 1.5 Ω N/A General Specifications Frequency Response (Main Channels) 12 Hz - 22 kHz (+0, -1dB) Frequency Response (Subwoofer Channel) 10 Hz - 1 kHz (+0, -1dB) S/N Ratio, referred to highest rated power (Main Channels) >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power (Main Channels) <1% @ 2 Ω per Ch. THD+N @ Rated Power (Subwoofer Channels) <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 60 A (AFS, AGU or MaxiFuse™)   Signal Processing Filter Mode(s): Channels 1 & 2 (front) High-Pass only Filter Slope(s): Channels 1 & 2 (front) 12 dB/octave Filter Frequency Range: Channels 1 & 2 (front) 50 Hz - 5 kHz Filter Mode(s): Channels 3 & 4 (rear) High-Pass or Bandpass Filter Slope(s): Channels 3 & 4 (rear) 12 dB/octave Filter Frequency Range: Channels 3 & 4 50 Hz - 500 Hz Filter Mode(s): Subwoofer Channel Low-Pass only Filter Slope(s): Subwoofer Channel 12/24 dB/octave Filter Frequency Range: Subwoofer Channel 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Infrasonic Filter: Subwoofer Channel none Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes Sub Ch. or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A   Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 6.15 lb / 2.79 kg

8-Channel Class D Full-Range Car/Marine Amplifier, 100 W x 8 @ 2 Ω / 75 W x 8 @ 4 Ω - 14.4V The ultra-versatile XDM800/8 delivers eight channels of crystal-clear, full-range power and is capable of delivering a whopping 100 watts to each of its channels @ 2 ohms (14.4V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM800/8 is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. The XDM800/8 includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter, and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all eight amplifier channels directly from the driver's seat or cockpit. Here are a few examples of how the XDM800/8 can be used: Eight-channel Satellite Amp: drive four pairs of speakers with 75 W x 8 Big Four-Channel Satellite Amp: bridge to produce 200W x 4 @ 4Ω Six-Channel System Amp: drive front and rear satellites with 75 W x 4 @ 4Ω, plus two 4Ω subwoofers with 200 W each Staggered Six-Channel Satellite Amp: drive front speakers with 200 W x 2 @ 4Ω, plus four 4Ω speakers with 75 W each Staggered Five-Channel Satellite Amp: drive three front speakers with 200 W @ 4Ω + rear speakers with 75 W x 2 Four-Channel System Amp: drive left and right speakers with 200W x 2 @ 4Ω, plus two 4Ω subwoofers with 200W each Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access.   General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 4 AWG wire Fuse Rating 80 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or 4 or All Channels Channel Input Mode Switch Yes (2/4/6/8 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A   Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 14.73 in / 374 mm Depth (D) 7.09 in / 180 mm Physical Specifications

JL AUDIO XDM600/6-24V 6 CH. CLASS D, FULL-RANGE CAR/MARINE AMPLIFIER, 600 W The incredibly flexible XDM600/6-24V packs a serious full-range wallop and delivers a stunning 100 watts to each of its six channels into 2 ohms (28.8V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM600/6-24V is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. With the XDM600/6-24V, you have plenty of great use options. Configure it as a six-channel satellite amplifier with 75 W x 6 @ 4 Ω, or bridge four of its channels to create a staggered power four-channel amplifier with 200 W x 2 @ 4 Ω for your front satellites and 75 W x 2 @ 4 Ω for your rear satellites. You can also drive two subwoofers with 200 W each, plus a pair of satellites with 75W x 2. The XDM600/6-24V includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all six amplifier channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24 volt may result in damage to the product and will void the warranty.   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 75 W RMS x 6 @ 2 Ω 100 W RMS x 6 Bridged @ 4Ω 200 W RMS x 3 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 6 @ 2 Ω 90 W RMS x 6 Bridged @ 4Ω 180 W RMS x 3 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or 4 or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 5.8 lb / 2.63 kg

Coaxial Speaker System: 6 x 9-inch (150 x 230 mm) Woofer, 1.0-inch (25 mm) Aluminum Dome Tweeter C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles. To facilitate fit, spacer/adaptor rings are included allowing the C1-690x to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modeling and JL Audio's expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly, while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690x is a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-molded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the back plate. Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminum dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling. When it comes to value, C1 is the real deal! Sold as a pair. Grilles not available. General Specifications Continuous Power Handling (RMS) 60 W Recommended Amplifier Power (RMS) 10 - 100 W / Ch. System Efficiency 91.5 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 39 Hz - 22 KHz ± 3 dB Coaxial Physical Specifications Frame Outer Diameter* (A) 6.38 x 9.33 in / 162 x 237 mm Grille Tray Outer Diameter (B) N/A Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion** (D) 0.41 in / 10 mm Frontal Grille Protrusion (E) N/A Mounting Hole Diameter (F) N/A Mounting Depth (G) 2.75 in / 70 mm *Does not take into account mounting tabs**Frontal coaxial tweeter protrusion measured from mounting surface

1" (25 mm) Silk Dome Component Tweeter Born from shared technologies used in our flagship C7 speakers, the C6-100ct component tweeter benefits from vast speaker design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-100ct component tweeter features an edge-driven, pure silk dome diaphragm for smooth, high-frequency performance with remarkable off-axis response and damping. A neodymium motor and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor (DSP), such as the JL Audio TwK® DSP or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-100ct Component Tweeter Features:• Edge-driven pure-silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Design Bandwidth:With 48 dB/octave filters: 3-21 kHzWith 24 dB/octave filters: 4-21 kHzWith 12 dB/octave filters: 5-21 kHz Component tweeters are sold individually and include surface- and flush-mount fixtures and hardware. One 15 μF tweeter protection capacitor is also included.   General Specifications Continuous Power Handling (RMS) 75 W Recommended Amplifier Power (RMS) 25 - 100 W / Ch. Nominal Impedance 4 Ω Frequency Response 3 kHz - 21 KHz ± 3 dB Parameters Voice Coil Resistance (Re) 3.20 Ω Free Air Resonance (Fs) 1500 Hz Reference Efficiency (no) 0.602% Efficiency 90 dB @ 1W / 1m96 dB @ 1W / 0.5m Sensitivity 93 dB @ 2.83V / 1m Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.16 in / 55 mm Flush Mount Mounting Hole Diameter (B) 1.88 in / 48 mm Flush Mount Mounting Depth (C) 0.73 in / 19 mm Flush Mount Tweeter Frontal Protrusion (D1) 0.33 in / 8 mm Surface Mount Tweeter Frontal Protrusion (D2) 1.06 in / 27 mm

6.5" (165 mm) Component Woofer (with Grille) Born from shared technologies used in our flagship C7 speakers, the C6-650cw component woofer benefits from vast woofer design experience and advanced modeling systems of JL Audio. Ideal for active systems, the C6-650cw component woofer features a proprietary cast alloy frame outfitted with our Elevated Frame Cooling™ technology and a DMA-optimized motor system to generate outstanding midbass impact with ultralow distortion. Passive crossover networks are not included with C6 drivers, as they are designed for active systems. Instead, we recommend a high-quality tuning digital signal processor, such as the JL Audio TwK® DSP, or a VXi amplifier with built-in DSP, with a dedicated amplifier channel for each C6 loudspeaker in the system. Precise setup of equalization, delay and crossover filters will ensure optimal in-vehicle performance. C6-650cw Component Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grille Design Bandwidth:With 48 dB/octave filters: 55 Hz-6 kHzWith 24 dB/octave filters: 65 Hz-6 kHzWith 12 dB/octave filters: 80 Hz-6 kHz Component woofers are sold individually and include a plastic grille tray, one fine steel mesh grille and one electroformed JL Audio badge logo. General Specifications Continuous Power Handling (RMS) 100 W Recommended Amplifier Power (RMS) 25 - 150 W / Ch. System Efficiency 87.37 dB @ 1 W / 1 m System Nominal Impedance 4 Ω System Frequency Response 55 Hz - 6 KHz ± 3 dB Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface