All 4WD Parts and Accessories

JL AUDIO XDM600/6-24V 6 CH. CLASS D, FULL-RANGE CAR/MARINE AMPLIFIER, 600 W The incredibly flexible XDM600/6-24V packs a serious full-range wallop and delivers a stunning 100 watts to each of its six channels into 2 ohms (28.8V, 1% THD). The technology that makes this much power possible in such a compact chassis is our advanced NexD™ high-speed switching design, which permits full bandwidth Class D operation with extremely low distortion and remarkable efficiency. Suitable for car or boat installations, the XDM600/6-24V is built with marine-grade materials and features an exclusive, dual-mode input filter for noise-free performance in boats or cars. Automatic turn-on capability (via signal sensing or DC-offset sensing) is also onboard for easy factory system upgrades. With the XDM600/6-24V, you have plenty of great use options. Configure it as a six-channel satellite amplifier with 75 W x 6 @ 4 Ω, or bridge four of its channels to create a staggered power four-channel amplifier with 200 W x 2 @ 4 Ω for your front satellites and 75 W x 2 @ 4 Ω for your rear satellites. You can also drive two subwoofers with 200 W each, plus a pair of satellites with 75W x 2. The XDM600/6-24V includes a 12 dB / octave filter for each channel bank, which can be configured as a low-pass or high-pass filter and offers continuously variable cutoff frequency selection from 50-500 Hz. With the addition of an optional HD-RLC or MHD-RLC (water-resistant) remote level controller (each sold separately), you have the ability to adjust the level of two, four, or all six amplifier channels directly from the driver's seat or cockpit. Finished in a sleek, black powder-coat, all controls are protected beneath a gasketed, removable top cover for easy access. This amplifier is designed for operation in vessels with 24 volt, negative-ground electrical systems. Use of this product in vessels with positive ground and/or voltages other than 24 volt may result in damage to the product and will void the warranty.   Rated Continuous (RMS) Power @ 14.4 V @ 4 Ω 75 W RMS x 6 @ 2 Ω 100 W RMS x 6 Bridged @ 4Ω 200 W RMS x 3 Rated Continuous (RMS) Power @ 12.5 V @ 4 Ω 60 W RMS x 6 @ 2 Ω 90 W RMS x 6 Bridged @ 4Ω 180 W RMS x 3 General Specifications Frequency Response 12 Hz - 22 kHz (+0, -1dB) S/N Ratio, referred to highest rated power >104 dB below rated power (A-weighted, 20 Hz - 20 kHz noise bandwidth) S/N Ratio, referred to 1 W >84 dB (A-weighted, 20 Hz - 20 kHz noise bandwidth) Damping Factor @ 4 Ω >150 / 50 Hz Damping Factor @ 2 Ω >75 / 50 Hz THD+N @ Rated Power <1% @ 2 Ω per Ch. Input Voltage Range @ RCA Inputs 200 mV - 4 V RMS Min.Copper Power / Ground Wire Gauge 8 AWG wire Fuse Rating 30 A (AFS, AGU or MaxiFuse™) Signal Processing Filter Mode(s) Low-Pass or High-Pass Filter Slope(s) 12 dB/octave Filter Frequency Range 50 Hz - 500 Hz Detented, Calibrated Filter Freq. Potentiometers Yes Filter Defeat Function Yes Remote Level Control Optional HD-RLC or MHD-RLC (water-resistant) Remote Level Modes 2 or 4 or All Channels Channel Input Mode Switch Yes (2/4/6 ch.) Pass-Through Preamp Output None Source Channel Selection for PreOuts N/A Physical Specifications Height (H) 2.05 in / 52 mm Width (W) 10.23 in / 260 mm Depth (D) 7.09 in / 180 mm Net Weight 5.8 lb / 2.63 kg

Two-way Component System: 6.5" (165 mm) Woofer, 1" (25 mm) Silk Dome Tweeter   Born from shared technologies used in our flagship C7 speakers, the C6-650 component system combines the smoothness and transparency of a premium silk dome tweeter with a top-flight component woofer to create a loudspeaker system with exceptional refinement and dynamic capability. Benefiting from vast woofer design experience and advanced modeling systems of JL Audio, the 6.5" (165 mm) C6 component woofers feature purpose-engineered, cast alloy frames outfitted with our Elevated Frame Cooling technology. A DMA-optimized, forged and machined motor system generates outstanding midbass impact with ultra-low distortion. The 1" (25 mm) C6 component tweeters feature edge-driven pure silk dome diaphragms for smooth high-frequency performance with remarkable off-axis response and damping. Neodymium motors and ferrofluid cooling provide high-magnetic flux and improved reliability with extended response from a very compact motor system. Surface- and flush-mount fixtures are included to fit a wide variety of installation applications.  Premium passive crossover networks are included with each C6-650 component system. Featuring four levels of tweeter adjustment, these outboard filter networks are equipped with premium polyester film and electrolytic capacitors as well as low-loss air-core inductors — all accessible beneath a protective, polycarbonate cover. Each C6 passive crossover also includes an advanced electronic tweeter protection circuit designed to minimize the possibility of tweeter failure. C6 Woofer Features:• Forged and machined motor plates with DMA-optimized geometries to create linear motor force under power, leading to outstanding midbass impact, linearity and low distortion• Large diameter, linear profile, flat spider for linear compliance and outstanding excursion capability• Center cap designed to optimize the high-frequency response of the woofer for seamless transition to a tweeter’s response• Oversized voice coil for extended power handling capability, minimizing thermal compression and distortion at higher listening levels• Cast alloy frame with our Elevated Frame Cooling feature• Includes fine mesh grilles C6 Tweeter Features:• Edge-driven pure silk dome design delivers smooth high-frequency performance, with excellent off-axis response and damping• Neodymium motor delivers high magnetic flux from a compact motor design• Ferrofluid cooling and damping improves reliability and response smoothness• Includes surface- and flush-mount fixtures Woofer grilles are included, each consisting of a black grille tray and a fine steel mesh grille with an electroformed JL Audio badge logo. Speakers are sold as a pair. General SpecificationsContinuous Power Handling (RMS)    100 WRecommended Amplifier Power (RMS)    25 - 150 W / Ch.System Efficiency    87.37 dB @ 1 W / 1 mSystem Nominal Impedance    4 ΩSystem Frequency Response    53 Hz – 21 KHz ± 3 dB   Woofer Physical Specifications Frame Outer Diameter* (A) 6.50 in / 165 mm Grille Tray Outer Diameter** (B) 6.76 in / 172 mm Motor Outer Diameter (C) 3.54 in / 90 mm Frontal Coaxial Tweeter Protrusion (D) N/A Frontal Grille Protrusion*** (E) 1 in / 25 mm Mounting Hole Diameter (F) 5.46 in / 139 mm Mounting Depth (G) 2.60 in / 66 mm *Does not take into account mounting tabs**Does not take into account logo badge***Frontal grille protrusion measured from mounting surface Tweeter Physical Specifications Flush Mount Fixture Diameter (A1) 2.13 in / 54 mm Surface Mount Fixture Diameter (A2) 2.11 in / 54 mm Flush Mount Mounting Hole Diameter (B) 1.85 in / 47 mm Flush Mount Mounting Depth (C) 1.85 in / 47 mm Flush Mount Protrusion (D1) 0.30 in / 8 mm Surface Mount Protrusion (D2) 1.04 in / 26 mm Crossover Physical Specifications Width (W) 3.36 in / 85 mm Height (H) 1.44 in / 37 mm Depth (D) 4.72 in / 120 mm

TW1 10-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 10TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.35 cu.ft. / 10 liters). This, combined with a special cast alloy frame design, makes the 10TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 10TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 10TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 10TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 10TW1 is optimized for an enclosure much smaller than any other JL Audio ten-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.36 in / 111 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.375 in / 264 mm Mounting Hole Diameter (B) 9.0625 in / 230 mm Bolt Hole Circle Diameter (C) 9.7 in / 246 mm Motor Outer Diameter (D) 4.54 in / 115 mm Mounting Depth (E) 4.36 in / 111 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.047 cu ft / 1.33 L Net Weight 10.5 lb / 4.8 kg Parameters Free Air Resonance (Fs) 41.45 Hz Electrical “Q” (Qes) 0.696 Mechanical “Q” (Qms) 9.7 Total Speaker “Q” (Qts) 0.649 Equivalent Compliance (Vas) 0.364 cu ft / 10.31 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 82.5 dB SPL Effective Piston Area (Sd) 41.602 sq in / 0.0268 sq m DC Resistance (Re) 2.428 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.35 cu ft / 9.91 L External Width (W) 16.125 in / 410 mm External Height (H) 14 in / 356 mm External Depth (D) 5.25 in / 133 mm F3 48.31 Hz Fc 59.21 Hz Qtc 0.927 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.625 cu ft / 17.7 L External Width (W) 26.625 in / 676 mm External Height (H) 16 in / 406 mm External Depth (D) 5.25 in / 133 mm Internal Slot Port Width (SW) 3.75 in / 95 mm Internal Slot Port Height (SH) 1.875 in / 48 mm Internal Slot Port Length (SL) 22.50 in / 572 mm Port Extension Length (EL) 20.8125 in / 529 mm Tuning Frequency (Fb) 35.0 Hz F3 30.56 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

TW1 12-inch Subwoofer (300 W, 2 Ω) Built on JL Audio's patented thin-line subwoofer technology, the 12TW1 delivers a powerful combination of shallow mounting depth and excursion capability, while operating in insanely small enclosures (0.65 cu.ft. / 18.4 liters). This, combined with a special cast alloy frame design, makes the 12TW1 capable of operating in extremely tight spaces. These include under-seat installations in trucks, 2-seat sports cars and many other creative applications requiring a compact, low profile subwoofer design. JL Audio's patented thin-line woofer technology compresses the architecture of the 12TW1 using a "concentric tube" structure built into the injection-molded cone body. This structure supports the voice coil and a full annular spider, while permitting the placement of a large motor structure further forward in the speaker than with conventional designs. The 12TW1 also features a clever frame design that minimizes the frontal clearance required for the excursion of the driver. This is accomplished by recessing the suspension attachment surface, so that most of the forward excursion occurs within the frame's dimensions. Thanks to this feature, the 12TW1 requires only 0.87 inches (22 mm) of frontal clearance, even with its grille installed. This allows for more efficient use of space and increased enclosure volume within a given overall depth. Even though the 12TW1 is optimized for an enclosure much smaller than any other JL Audio twelve-inch Subwoofer, it never sounds like a big woofer struggling in a tiny box...instead, it delivers all the rich, deep, controlled bass you have come to expect from a JL Audio subwoofer system. Very shallow mounting depth (4.62 in / 117 mm) No pole vent: permits mounting close to rear wall of enclosure Extremely small sealed enclosure volume requirements Long linear excursion capability (0.40 in / 10 mm, one-way) DMA-optimized motor design Patented "concentric tube" architecture Patented "floating cone attach method" technology Cast alloy frame with flat edges for tight driver grouping Injection molded, mica-filled polypropylene cone Rubber surround Steel mesh grille included with each driver Precision-built in USA at JL Audio’s Miramar, Florida factory with global components General Specifications Continuous Power Handling (RMS) 300 W Recommended Amplifier Power (RMS) 75 - 300 W Nominal Impedance (Znom) 2 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.375 in / 314 mm Mounting Hole Diameter (B) 11.0625 in / 281 mm Bolt Hole Circle Diameter (C) 11.7 in / 297 mm Motor Outer Diameter (D) 5.71 in / 145 mm Mounting Depth (E) 4.62 in / 117 mm Front Grille Protrusion (F) 0.87 in / 22 mm Driver Displacement 0.072 cu ft / 2.04 L Net Weight 16.5 lb / 7.5 kg Parameters Free Air Resonance (Fs) 35.06 Hz Electrical “Q” (Qes) 0.61 Mechanical “Q” (Qms) 10.662 Total Speaker “Q” (Qts) 0.577 Equivalent Compliance (Vas) 1.008 cu ft / 28.54 L One-Way Linear Excursion (Xmax)* 0.40 in / 10.0 mm Reference Efficiency (no) Efficiency (1 W / 1 m)** 85.07 dB SPL Effective Piston Area (Sd) 67.608 sq in / 0.0436 sq m DC Resistance (Re) 2.430 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** Efficiency (1 W / 1 m) is not an accurate indicator of a subwoofer’s output capability and should not be used as a comparison to other subwoofers to determine which one is “louder”. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.65 cu ft / 18.41 L External Width (W) 26.50 in / 673 mm External Height (H) 14 in / 356 mm External Depth (D) 5.50 in / 140 mm F3 45.83 Hz Fc 55.99 Hz Qtc 0.92 Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.125 cu ft / 31.86 L External Width (W) 31.75 in / 806 mm External Height (H) 16 in / 406 mm External Depth (D) 7 in / 178 mm Internal Slot Port Width (SW) 5.50 in / 140 mm Internal Slot Port Height (SH) 2.25 in / 57 mm Internal Slot Port Length (SL) 22.625 in / 575 mm Port Extension Length (EL) 20.75 in / 527 mm Tuning Frequency (Fb) 34.0 Hz F3 31.52 Hz Enclosure Notes* The enclosure recommendations listed above are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6.5 mm) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed above are net internal volumes! Driver displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions above have already taken this into account.* When using multiple subwoofers in a common enclosure you will need to recalculate the enclosure and port dimensions. For assistance please contact your authorized JL Audio dealer or JL Audio Technical Support.* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and a high-quality amplifier. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.* All specifications are subject to change without notice. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 10-inch Subwoofer (600 W, dual 4 Ω voice coils) If you are seeking to reproduce the highest quality sub-bass in a very compact enclosure application, the 10W6v3 is the ultimate choice. This advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 10W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 0.55 cu. ft. (15.6 l) of air space, or a 0.75 cu. ft. (21.2 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 10W3v3 10-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 10.0 in / 250 mm Overall Diameter (A) 10.5 in / 267 mm Mounting Hole Diameter (B) 9.02 in / 229 mm Bolt Hole Circle Diameter (C) 9.86 in / 250 mm Motor Outer Diameter (D) 6.76 in / 172 mm Mounting Depth (E) 6.89 in / 175 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.078 cu ft / 2.1 L Net Weight 20 lb / 9.1 kg Parameters Free Air Resonance (Fs) 30.12 Hz Electrical “Q” (Qes) 0.543 Mechanical “Q” (Qms) 9.228 Total Speaker “Q” (Qts) 0.513 Equivalent Compliance (Vas) 0.821 cu ft / 23.25 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 82.7 dB SPL Effective Piston Area (Sd) 49.303 sq in / 0.0318 sq m DC Resistance (Re)*** 6.452 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.55 cu ft / 15.57 L External Width (W) 12.5 in / 318 mm External Height (H) 12.5 in / 318 mm External Depth (D) 10.5 in / 267 mm F3 42.27 Hz Fc 47.55 Hz Qtc 0.8099 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 0.75 cu ft / 21.2 L External Width (W) 21.5 in / 546 mm External Height (H) 12.375 in / 314 mm External Depth (D) 11.125 in / 282 mm Internal Slot Port Width (SW) 1.375 in / 35 mm Internal Slot Port Height (SH) 10.875 in / 275 mm Internal Slot Port Length (SL) 30.40 in / 772 mm Port Extension Length (EL) 16.5 in / 419 mm Tuning Frequency (Fb) 39 Hz F3 33 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

W6v3 12-inch Subwoofer (600 W, dual 4 Ω voice coils)   If you are seeking intensely powerful sub-bass that compromises nothing in terms of sound quality, the 12W6v3 is your ultimate ally. This highly advanced Subwoofer offers several technologies shared with the flagship W7AE subwoofers to provide powerful advantages in motor linearity and suspension behavior. These combine with a very efficient cooling circuit to deliver reduced distortion and outstanding dynamic balance. The 12W6v3 is best used with amplifier power in the 200W - 600W range and is optimized to operate in a sealed enclosure with only 1.0 cu. ft. (28.3 l) of air space, or a 1.3 cu. ft (36.8 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. Greater excursion capability and higher power handling distinguish it from our 12W3v3 12-inch Subwoofer, allowing for higher output. Dual 4 Ω voice coils permit deploying the W6v3 as a 2 Ω or 8 Ω driver. General Specifications Continuous Power Handling (RMS) 600 W Recommended Amplifier Power (RMS) 200 - 600 W Nominal Impedance (Znom) Dual 4 Ω Physical Specifications Nominal Diameter 12.0 in / 300 mm Overall Diameter (A) 12.5 in / 318 mm Mounting Hole Diameter (B) 11.02 in / 280 mm Bolt Hole Circle Diameter (C) 11.86 in / 301 mm Motor Outer Diameter (D) 7.0 in / 178 mm Mounting Depth (E) 7.52 in / 191 mm Required Pole Vent Clearance 0.50 in / 13 mm Driver Displacement 0.105 cu ft / 2.97 L Net Weight 25.6 lb / 11.6 kg Parameters Free Air Resonance (Fs) 26.919 Hz Electrical “Q” (Qes) 0.487 Mechanical “Q” (Qms) 9.365 Total Speaker “Q” (Qts) 0.463 Equivalent Compliance (Vas) 1.920 cu ft / 54.37 L One-Way Linear Excursion (Xmax)* 0.75 in / 19 mm Reference Efficiency (no) 0.11% Efficiency (1 W / 1 m)** 85.4 dB SPL Effective Piston Area (Sd) 75.338 sq in / 0.0486 sq m DC Resistance (Re)*** 6.493 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.0 cu ft / 28.3 L External Width (W) 15 in / 381 mm External Height (H) 15 in / 381 mm External Depth (D) 12 in / 305 mm F3 41.62 Hz Fc 45.99 Hz Qtc 0.7912 Download detailed sealed enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located around the JL Audio badge at the rear of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 0.75 in / 19 mm Volume (net int.) 1.3 cu ft / 36.8 L External Width (W) 27 in / 686 mm External Height (H) 14 in / 356 mm External Depth (D) 12.5 in / 318 mm Internal Slot Port Width (SW) 1.75 in / 44 mm Internal Slot Port Height (SH) 12.5 in / 318 mm Internal Slot Port Length (SL) 37.125 in / 943 mm Port Extension Length (EL) 21.250 in / 540 mm Tuning Frequency (Fb) 33 Hz F3 31 Hz Download detailed ported enclosure information Enclosure Notes* The W6v3’s employ a pole vent to remove heat and pressure from the inside of the speaker. A minimum distance of 0.5 in (13 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent.* The enclosure recommendations listed are external dimensions which assume the use of 0.75 in (19 mm) thick material. If you are using 0.625 in (16 mm) thick material, subtract 0.25 in (6) from each dimension. Do not use any material with a thickness of less than 0.625 in (16 mm) as this may compromise the rigidity of the enclosure.* All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.* When using two subwoofers in a common enclosure simply double the required volume and, in the case of a ported enclosure, use two times the recommended port(s).* We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance. Safety NoticeProlonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve your ability to enjoy its fidelity. When installing a subwoofer in your vehicle, it is extremely important to secure the enclosure firmly. We recommend bolting the enclosure through the metal of the floorpan or the frame of the vehicle with large diameter washers for reinforcement. If an enclosure is not firmly attached, it can become a projectile in a collision. This is particularly important in a hatchback, station wagon, sports utility vehicle, or van.

10th Anniversary Edition - W7 13.5-inch Subwoofer (1500 W, Dual 1.5 Ω voice coils) Words like "extreme," "reference" and "ultimate" get thrown around quite a bit in the Subwoofer world, but rare is the product that can honestly lay claim to them. The 13W7AE does. Taking the W7 design formula to its highest level, the 13W7AE offers a staggering linear excursion envelope that exceeds 1.25 inches (32 mm) one-way, along with a suspension capable of over 4-inches of peak-to-peak excursion. Combine that with a piston diameter that is 28% larger than the 12W7AE's, and you have a serious high-performance driver for the most demanding applications. With a 13W7AE, limits simply vanish and amazing sub-bass happens... on all fronts, at any level. Our most potent Subwoofer is best used with amplifier power in the 500W - 1500W range and is optimized to operate in a 1.875 cu. ft. (53.1 l) sealed enclosure, or a 2.375 cu. ft. (67.3 l) ported enclosure. Detailed enclosure recommendations can be found in the "Specifications" tab. W7AE (Anniversary Edition) Subwoofers celebrate the 10th Anniversary of the launch of the W7 subwoofers. Functionally, they are identical to the original W7's, but they are distinguished by the following cosmetic differences: Satin-Black Powdercoated Baskets Bright Anodized Surround Clamp Ring Anniversary Edition Cone Badge Anniversary Edition Terminal Label General Specifications Continuous Power Handling (RMS) 1500 W Recommended Amplifier Power (RMS) 500 - 1500 W Nominal Impedance (Znom) Dual 1.5 Ω Physical Specifications Nominal Diameter 13.5 in / 345 mm Overall Diameter (A) 14 in / 356 mm Mounting Hole Diameter (B) 11.9 in / 302 mm Bolt Hole Circle Diameter (C) 12.7 in / 323 mm Motor Outer Diameter (D) 8.38 in / 213 mm Mounting Depth (E) 10.5 in / 267 mm Driver Displacement 0.21 cu ft / 5.9 L Net Weight 52 lb / 23.6 kg Parameters Free Air Resonance (Fs) 23.5 Hz Electrical “Q” (Qes) 0.476 Mechanical “Q” (Qms) 7.517 Total Speaker “Q” (Qts) 0.448 Equivalent Compliance (Vas) 3.68 cu ft / 104.3 L One-Way Linear Excursion (Xmax)* 1.25 in / 32 mm Reference Efficiency (no) 0.27% Efficiency (1 W / 1 m)** 86.3 dB SPL Effective Piston Area (Sd) 107.35 sq in / 0.0693 sq m DC Resistance (Re)*** 2.41 Ω * Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.** For parallel-wired voice coils, divide "Re" by 4. All other specifications remain the same.*** Re (DC resistance) is measured with the voice coils in series, for parallel-wired specification divide Re by 4. All other specifications remain the same. Sealed Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 1.875 cu ft / 53.1 L External Width (W) 16 in / 407 mm External Height (H) 16 in / 407 mm External Depth (D) 18.875 in / 479 mm F3 37.4 Hz Fc 40.5 Hz Qtc 0.77 Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker. This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration. Ported Enclosure Specifications Wall Thickness 0.75 in / 19 mm Front Baffle Thickness 1.0 in / 25 mm Volume (net int.) 2.375 cu ft / 67.3 L External Width (W) 25.875 in / 657 mm External Height (H) 16 in / 406 mm External Depth (D) 17.25 in / 438 mm Internal Slot Port Width (SW) 2.25 in / 57 mm Internal Slot Port Height (SH) 14.5 in / 368 mm Internal Slot Port Length (SL) 26.25 in / 667 mm Port Extension Length (EL) 7.875 in / 200 mm Tuning Frequency (Fb) 34.6 Hz F3 30.3 Hz Enclosure NotesNet volumes given above do not include the air volume displaced by the speaker (Driver Displacement). This value must be added to the net volume along with the displacement of any braces and/or ports (if applicable) to arrive at a gross internal volume. Air inside a port is not part of the effective net volume. Calculate ports as solid, not hollow objects. * The W7’s employ a pole vent to remove heat and pressure from the inside of the speaker.This vent is located at the rear of the speaker. A minimum distance of 0.75 in (19 mm) is required between the back of the speaker and any wall of the enclosure to allow proper operation of the pole vent. The dimensions given for the enclosure examples above take all applicable displacements into consideration Safety NoticeIt is absolutely essential that the completed subwoofer enclosure is mounted firmly to the vehicle with heavy steel bolts (0.5 in diameter) and large steel washers on both sides of the bolts. This will reduce the likelihood of occupant injury in the event of a collision or sudden deceleration.

Alpine Hilux 2012-2015 R2 Series Speaker Solution ( Front & Rear ) -Hl15-R265 Turn up the bass in your Toyota Hilux — the next Generation R-Series are born to be played loud with Alpine’s all-new R-Series ‘direct fit’ premium speaker upgrade. Equipped with Alpine’s exclusively designed tweeter housing superior sound quality is achieved, all-while your cabin space is enhanced with its striking appearance and premium finishes inclusive of a machine finished metal Alpine logo and contrasting black chrome accent. Alpine engineered and reborn from the ground up, the all-new R-Series speaker housings unites true Hi-Fi sound quality and ultra-bass performance with precise and direct replacement of the factory installed speakers. All parts are pre-assembled with ‘plug-n-play’ connections providing a straight forward, no-fuss installation with no need of any modifications, cutting of wires, nor soldering. Perfect Integration Alpine’s premium design ‘A Pillar’ direct-fit tweeter housing with a machine cut Alpine logo and an elegant black chrome bezel which are all pre-assembled parts ready for direct installation to your Toyota Hilux. Premium Design Tweeter Housing Premium audio never looked so good. The bold, yet ornate design of the tweeter housing directly replaces the OEM which elevates the interior aesthetic and optimises the tweeter axis for superior sound quality. Hi-Res Audio Certified Hard Dome Tweeter The all-new magnesium hard-dome tweeters housed within the centre of the speaker and tweeter delivers an ultra-clear, yet highly detailed and smooth response. They play right up to 40kHz allowing harmonics to reveal the finest of nuances for an authentic sound experience, faithfully to the original recording. Direct Fit Installation All speakers interface directly to the OEM, providing a quick and easy ‘plug-n-play’ connection. This means there is no need to cut, solder or modify any of the vehicle’s original wiring — saving you time by easily utilising the original speaker wires, allowing for a straight and simple installation. Larger Magnet Structure The new R-Series speakers feature a larger magnet structure for incredible bass. Despite this, the driver depth is unchanged from the previous generation to retain installation versatility, but with improved performance. Glass-Fibre Reinforced Cone The high-performance midrange and woofer drivers feature an all-new glass-fibre reinforced cone. This material is extremely rigid and light-weight, resulting in exceptionally fast cone velocity and response time, delivering highly accurate music reproduction. Exclusive HAMR Surround Alpine’s High Amplitude Multi-Roll (HAMR) surround provides a greater maximum and linear cone excursion for high SPL. The HAMR surround maintains full control over the cone at any excursion stage for powerful bass and pure sound. High-Pass X-Over Network This small X-Over networks are very easy to install – in may cases you can keep the original wiring in the vehicle’s doors by simply putting this network in, saving lots of time during installation. You can adjust the tweeter level by -3dB / 0dB / +3dB. Features Tweeter Tweeter Type: 1” (2.5cm) Ring Radiator Tweeter Voice Coil Type: Dual Gap for optimum linearity and clarity Magnet Material: Neodymium Magnet Swivel Application allowing the sound to be focused for the best in-car sound performance Woofer Cone Material: Hybrid Multi Layer Cone Motor Technology: Linear Drive Technology Surround: HAMR Surround Voice Coil Type: Dual Gap Voice Coil for optimum linearity and clarity Magnet: Ultra High Density Neodymium Magnet DX Ring: DX Ring Wave Guide: Wave Guide Mounting: Shallow Mounting Design Mounting Adapters: Mounting Adapter Kit Included Design: Bi-Amp Ready Design General Peak Power Handling: 300W RMS Power Handling: 100W Nominal Impedance: 4ohms Frequency Response: 65Hz-40kHz In-Line High Quality Crossover 59mm Mounting Depth Swivel Tweeters Neodymium Magnet Multi-layer Hybrid Cone Dual Gap Voice Coil All-New Design Circuit for Precision Response Dimensions Woofer Diameter (mm): 165mm Woofer Diameter (in): 6-1/2″ Woofer Mounting Diameter (mm): 176mm Woofer Mounting Diameter (in): 6-15/16″ Woofer Mounting Depth (mm): 59mm Woofer Mounting Depth (in): 2-3/8″  

Free up space inside your Suzuki Jimny and organize your gear with this internal storage shelf. It features a flat, lightweight aluminum storage surface, as well as a molle panel underneath which allows additional gear to be secured with the adjustable webbing straps. This internal storage shelf fastens to the rear grab handle mounting points of the Suzuki Jimny. This shelf creates extra storage space and keeps items such as jackets and bedding neatly stored. The molle panel design allows additional adventure gear to be secured to the underside of the shelf with the adjustable webbing straps included. Made of lightweight aluminum and sealed with the same weather-resistant black powder coating as the Front Runner racks. Load capacity of 20kg / 44 lbs. No drilling is required, this internal storage tray installs on the existing OEM rear seat grab handles. The Molle Panel is compatible with the Suzuki Jimny 3 Door (2018-Current) Rear Window Molle Panel to maximize the load solutions. Consists of:1 x Internal Cargo Tray2 x Mounting Brackets1 x Hardware KitFitting Instructions   Materials used:Black powder coated aluminium Product Dimensions:1100mm (43.3") L x 424mm (16.7") W x 147mm (5.8") H Storage Dimensions:1000mm (39.4") L x 420mm (16.5") W Weight:2.74kg (6.1lbs) Load Rating:20kg (44.1lbs)

Upgrade your cargo slide with this strong, steel bracket which is used to secure a Drop Down Table to either side of the slide. The bracket will transform your slide as the table is a super-useful surface on which to place drinks or prepare food.   A bracket to secure the *Drop Down Tailgate Table to the *Load Bed Cargo Slide / Medium or the *Load Bed Cargo Slide / Large. This bracket bolts onto either the Left or Right side of your Load Bed Cargo Slide, to securely hold the *Drop Down Tailgate Table. Made of high strength steel and sealed in the same weather resistant black powder-coating as Front Runner racks. Note: This bracket is not suitable for front fitment or for fitment on the Load Bed Cargo Slide / Small. *Sold separately. Consists of:3 x Mounting BracketsInstallation hardwareFitting instructions Materials used:Black powder-coating high strength steel Product Dimensions:690mm (27.2") L x 237mm (9.3") W x 47mm (1.9") H Weight:1.89Kg (4.2lbs)

Elevate your snack or drink stops when adventuring in your vehicle with this Universal Drop Down Tailgate Table. Incredibly, it can be fitted onto any flat surface, providing a handy, on-the-go workspace. Perfect for putting the kettle, cups, glasses, or snacks on. This Universal Drop Down Table will fit on any flat surface equal to, or larger than: 640mm/25.2" W x 330mm/13" H. It is a universal drop down table features a large working surface of 615mm/24.2" W x 257mm/10.1" L, perfect for small cooking appliances, kettle/coffee station.  Stores neatly at 64mm/2.5" when closed. The Universal Drop Down Table lowers to open at 90 degrees from the mounted base.  The table latch features a hole to securely lock the drawer in place, Rack Accessory Lock / Small can be used. *Sold Separately   Maximum load: 20Kg (44.1lbs). Drilling is required for installation. Installation hardware and fitment guide included.  Consists of:1 x Table Assembly1 x Catch Assembly2 x Arm Assembly2 x Mounting Bracket (1 Left Hand side & 1 Right Hand side)Installation HardwareFitting Instructions Product Dimensions:Closed Dimensions:64mm (2.5") L x 636mm (25.03") W x 320mm (12.60") H Fully Opened Dimensions:264mm (10.4") L x 636mm (25.03") W x 320mm (12.60") H Weight:3.2kg (7.05lbs) Load Rating:20kg (44.1lbs)

A complete under rack table and table-storage solution that allows you to effortlessly load, transport and access your table when out on any adventure. The Under Rack Table Kit mounts underneath your Front Runner Roof Rack and features the Under Rack Table –– which has an aluminum PVDF top and high-strength black powder-coated steel frame –– as well as the brackets, slides, and latches needed to mount it.   A complete camp table and table storing solution. Effortlessly take a previously cumbersome luxury item on any vehicle-based adventure. Under Rack Table: The table frame slides into the storage brackets and is secured with the table latch eliminating any excessive noise. An aluminum PVDF table top ensures a hygienic surface for preparing and serving meals. The table frame and legs are powder-coated black with the same durable, corrosion-resistant coating as the Front Runner Slimline II Roof Rack. Under Rack Table Bracket: A no-noise and secure storage solution designed specifically for the Under Rack Table. The brackets can be mounted both parallel and perpendicular to the roof rack's slats, allowing access to the table from the side or rear of the vehicle. Easy installation. Made of steel and is black powder-coated in the same durable and corrosion-resistant coating as the Front Runner Slimline II roof rack. Under Rack Table Latch : Keeps the Under Rack Table securely stored in the Under Rack Table Bracket. Secured to the top of the Slimline II roof rack using the T-slot and clamps over the lip of the table to keep it in place. A rubber insert prevents rattling and damage to the table. Spring loaded for ease of use. Lockable for added security. Made of steel and is black powder-coated in the same durable and corrosion-resistant coating as the Front Runner Slimline II roof rack. NOTE: Table fitment requires 65mm (2.5") clearance from under the rack to the highest point of the roof.Side mounting requires 4 open slats. Rear mounting requires 7 open slats and is not suitable for vehicles with rear roof antenna.Still unsure? Contact the Front Runner Help Center   Consists of:1 x Under Rack Table1 x Pro Table Under Rack Bracket1 x Under Rack Table Latch Under Rack Table:Materials used:Black composite table top with aluminium finishBlack powder coated steel frameBlack powder coated aluminium legs Product Dimensions:Closed Dimensions:1130mm (44.5") L x 750mm (29.5") W x 32mm (1.3") H Open Dimensions:1130mm (44.5") L x 750mm (29.5") W x 750mm (29.5") H Weight:11.2kg (24.7lbs) Under-Rack Table Latch:Materials used:Black Powder-coated high strength steelPVC Grommet Product Dimensions:115mm (4.5") H x 50mm (2") W x 50mm (2") L Weight:200g (7oz) Under-Rack Table Bracket:Materials used:Black Powder-coated high strength steelPVC Grommet Product Dimensions:980mm (38.6") L x 63mm (2.5") W x 44mm (1.8") H (Single Bracket) Weight:3.8kg Full Kit Dimensions:1160mm (14.2") L x 837mm (33") W x 114mm (4.5") H Full Kit Weight:15.2kg (33.5lbs) TABLE CARE: Keep your table clean and sparkling with these easy care instructions. Add a small amount of dish soap to a damp soft cloth.Dry excess moisture with a dry towel. Done!

Transport your Front Runner Table underneath your roof rack with this noise-free, easy-access solution. These off-road tough brackets can be mounted either parallel or perpendicular to the roof rack's slats giving you the option to access the table from either the side or rear of the vehicle. These brackets have been designed to work in conjunction with the Under Rack Table and Under Rack Table Latch to make transporting a sturdy table as simple and effortless as possible. Under Rack Table: A no-noise and secure storage solution designed specifically for the Under Rack Table. The brackets are easily installed and can be mounted either parallel or perpendicular to the roof rack's slats giving you the option to access the table from either the side or rear of the vehicle. Made from steel and black powder-coated in the same durable and corrosion-resistant coating as Front Runner racks. Under Rack Table Latch: Keeps the Under Rack Table securely stored in the Under Rack Table Brackets. Secured to the top of the Slimline II rack using the T-slot and clamps over the lip of the table to keep it in place. A rubber insert prevents rattling and damage to the table. Spring-loaded for ease of use. Lockable for added security. Made of steel that is black powder coated in the same durable and corrosion-resistant coating as the Front Runner racks. NOTE: A min clearance of 65mm (2.5") between the underside of the rack and the crown of the roof is required for fitment of a Front Runner Table Kit.Not all Foot Rails accommodate side mount Tables. If unsure? Please contact the Front Runner Help Center. Consists of:2 x Table Slide Bracket1 x Table LatchInstallation HardwareFitment Instructions Materials used:Black powder-coated high strength steel Product Dimensions:Single Side Bracket Dimensions:980mm (38.6") L x 63mm (2.5") W x 44mm (1.8") H Latch Dimensions:50mm (2") L x 50mm (2") W x 115mm (4.5") HWeight:4kg (8.8lbs)

The lightweight Under Rack Table was engineered to be easily stored underneath most Front Runner Slimline II Roof Racks leaving more space for your gear on top. This lightweight, sturdy full-sized Under Rack Table is ideal for food preparation, food serving, and gathering around for a sit-down camp dinner. Features include an aluminium PVDF top and black powder-coated aluminium and high-strength steel frame.

A roof top tent negates the major hassle of pitching (and breaking down) a tent and also keeps you off the cold ground. Our Roof Top Tent weighs only 43kg and sleeps two comfortably. Use these mounting brackets to attach it to your Front Runner roof rack. These shorter brackets match the Roof Rack's low profile for a clean aesthetic. Mount most roof top tents to the Roof Rack with these shorter brackets (30mm H) to match the rack’s low profile. Black powder-coated steel. Pre-cut mounting holes. Mounting pieces (eg. bolts and nuts) included. Consists of:6 x Tent Mount Kit Brackets Materials used:2mm (0.078") Black powder coated steelProduct Dimensions:245mm (9.6") L x 60mm (2.4") D x 30mm (1.2") HWeight:2.1kg (4.6lbs)

Storing, organizing, and moving gear in the Toyota Prado/Lexus GX 470 just got easier. This Cub Pack based lockable drawer system provides a comprehensive and practical storage solution for easily transporting stored items between a vehicle and the campsite, garage, store, etc. Designed specifically to fit the contours of the Toyota Prado/Lexus GX470. Engineered tough for both on and off-road conditions. This removable box drawer kit includes 1 drawer slides, 6 Front Runner Cub Packs, locks and keys, 3 tie down rails, 6 tie down rings, brackets, all necessary installation hardware, and detailed fitment instructions.Front Runner Cub Packs, the heart of this modular storage system, are perfectly sized for kitchen supplies, dried goods, tools, camera gear, toiletries, even clothes.These stackable and durable Cub Pack storage containers are made from black, high strength plastic and have integrated grips for easy carrying. 113kg / 250 lb per drawer load carrying capacity. Hold open feature: drawers\ “lock” open while parked on uneven surfaces. High-strength bearing slides allows each drawer to extend nearly 100% from the anchored base. The push-to-latch mechanism is lockable when closed. Provide peace of mind and security by locking away important support gear. The flat deck incorporates three cargo attachment channels and 6 Black Tie Down Rings / Eye Nuts. Customize your own storage configurations. Stack and secure luggage, Wolf Pack Pro, Cub Pack, aluminium boxes and other storage containers to the top deck using Stratchits. The deck above the drawer can also be used to mount Front Runner Cargo/Fridge Slides. The left and right-side Faceplates have 4, pre-cut, knock-outs each for adding electrical panel socket inserts (sold separately). The side decks are easily removable creating storage pockets between the drawers and vehicle for a variety of items such as tools, jumper cables, tow ropes, snorkels, masks, fins, kindling, barbeque skewers, etc. The deck is covered with a durable, UV resistant nylon pile carpet. The nylon carpet surface creates resiliency for securing cargo while insulating against noise and vibration. Finished with the same durable black powder coating as the Front Runner Slimline Rack and other Front Runner products. This Front Runner Removable Box Drawer Kit can be easily installed in minutes by attaching the supplied C-hooks and turnbuckles to the vehicle’s existing mounting points. Removing the drawers is just as easy. This storage system is designed for interior use.   All Front Runner Storage Systems are backed by a 2 year warranty.If you have any questions about whether or not this product will fit your vehicle, please contact Front Runner before purchase. Consists of:1 x Drawer unit with 1 Opening Drawer1 x Push to close latch with 2 keys1 x Deck Completion Set3 x Accessory Channels6 x Tie Down Rings6 x Cub PacksInstallation HardwareFitting InstructionMaterials used:Black powder coated steel - FrameCarpet & Laminated Plywood - Top and Side DecksProduct Dimensions:Overall Dimensions:1000mm (39.4") L x 1425mm (56.1") W x 338mm (13.3") HOpen Drawer Dimensions:1915mm (75.4") L x 950mm (37.4") W x 285mm (11.2") HInner Drawer Dimensions:946mm (37.2") L x 890mm (35") W x 222mm (8.7") HWeight:72.1kgLoad Rating:113kg (250lbs)Special Notes:Items can be secured to the top deck using the 6 supplied tie down rings and fitting them accordingly to the 3 accessory channels on the top deck.Drawer has a hold open feature.

Make storing and organizing gear and valuables a no-brainer. This lockable drawer, with fitted decks and faceplates, has been designed specifically for the Toyota Land Cruiser 79 DC. Hide contents from prying eyes while creating more usable and easily accessible storage space in your vehicle.Engineered tough for both on and off-road travel. This drawer kit has 1 lockable drawer, 2 keys per lock, 3 tie-down rails, 6 tie-down rings, deck completion set, face completion set, brackets, all necessary installation hardware, and detailed fitment instructions. 180kg / 397lb drawer load carrying capacity. Hold open feature: drawer "locks" open while parked on uneven surfaces. High-strength bearing slides allow the drawer to extend nearly 100% from the anchored base. Provide peace of mind and security by locking away important travel items such as computers, smartphones, and camera gear. The flat deck incorporates three cargo attachment channels and 6 Black {SSCA047~showName). Customize your own storage configurations. Stack and secure luggage, Wolf Pack Pro, Cub Pack, aluminum boxes and other storage containers to the top deck using Stratchits or other straps. The deck above the drawers can also be used to mount Front Runner Cargo/Fridge Slides. The side decks are easily removable creating storage space between the drawers and vehicle for a variety of items such as tools, jumper cables, tow ropes, diving snorkels, masks, fins, kindling, barbeque skewers, etc. To create a removable box option, use Cub Pack or Flat Pack inside the drawers. The Cub Pack or Flat Pack can be used to further organize and easily move gear in and out of a vehicle. The deck is covered with a durable, UV resistant nylon pile black carpet detailed to complement the vehicle’s interior contours. The nylon carpet surface creates resiliency for securing cargo while insulating against noise and vibration.Finished with the same durable black powder coating as Front Runner Roof Racks and other Front Runner products. This drawer kit can be easily installed in minutes by securing the drawers via 3 channels and supplied hardware. Drilling is required to fit the 3 securing channels into the Toyota Land Cruiser 79 load bed. All Front Runner Storage Systems are backed by a 2 year warranty. *Please Note: Cub Packs and Flatpack Storage Boxes are not included when purchasing this Drawer System and are sold separately.Note: The Deck Completion Set for this drawer kit requires modification when installed with an existing plastic load liner. Consists of:1 x Front Runner Drawer unit (SSDR012)1 x Toyota Land Cruiser 79 DC Drawer Deck Completion Set (SSDS120)1 x Custom Wing Set1 x Push to Close latch with 2 keys per lock3 x Accessory Channels6 x Eye Nuts for Accessory ChannelsInstallation HardwareFitting InstructionsMaterials used:Aluminum - Accessory ChannelsBlack powder coated steel - Drawer Bins, Frame & Mounting ChannelsCarpeted & Laminated plywood - Top Deck & Deck SetsProduct Dimensions:Overall Closed Dimensions:1510mm (59.5") L x 1575mm (62") W x 295mm (11.6") HDrawer Internal Dimensions:1100mm (43.3") L x 747mm (29.4") W x 208mm (8.2") HOpen Dimensions:2100mm (82.7") L x 860mm (33.9") W x 295mm (11.6") HWeight:89.3kg (196.9lbs)Load Rating:180kg (396.8lbs)

Make storing and organizing gear and valuables a no-brainer. This lockable drawer with fitted decks and faceplates have been designed specifically for the Toyota Land Cruiser 79 DC. Hide contents from prying eyes while creating more usable and easily accessible storage space in your vehicle.Engineered tough for both on and off-road travel. This drawer kit has 1 lockable drawer, 2 keys per lock, 3 tie down rails, 6 tie down rings, deck completion set, face completion set, brackets, all necessary installation hardware, and detailed fitment instructions. 180kg / 397lb drawer load carrying capacity. Hold open feature: drawer "locks" open while parked on uneven surfaces. High-strength bearing slides allow the drawer to extend nearly 100% from the anchored base. Provide peace of mind and security by locking away important travel items such as computers, smart phones and camera gear. The flat deck incorporates three cargo attachment channels and 6 Tie Down Rings / Eye Nuts For Drawer System. Customize your own storage configurations. Stack and secure luggage, Wolf Pack Pro, Cub Pack, aluminum boxes and other storage containers to the top deck using Stratchits or other straps. The deck above the drawers can also be used to mount Front Runner Cargo / Fridge Slides. A fridge (footprint of 750mm x 425mm or smaller) can be installed on the left hand side of the drawer for access through a gullwing style window. The right rear deck and back right side deck each have a cut out (215mm in diameter) to fit and secure a gas/propane bottle or similar shaped object. The side decks are easily removable creating storage space between the drawers and vehicle for a variety of items such as tools, jumper cables, tow ropes, diving snorkels, masks, fins, kindling, barbeque skewers, etc. To create a removable box option, use Cub Pack or Flat Pack inside the drawers. The Cub Pack or Flat Pack can be used to further organize and easily move gear in and out of a vehicle. The deck is covered with a durable, UV resistant nylon pile black carpet detailed to complement the vehicle’s interior contours. The nylon carpet surface creates resiliency for securing cargo while insulating against noise and vibration. Finished with the same durable black powder coating as Front Runner Roof Racks and other Front Runner products. This drawer kit can be easily installed in minutes by securing the drawers via 3 channels and supplied hardware. Drilling is required to fit the 3 securing channels into the Toyota Land Cruiser 79 load bed.   All Front Runner Storage Systems are backed by a 2 year warranty.*Please Note: Cub Packs and Flatpack Storage Boxes are not included when purchasing this Drawer System and are sold separately.Note: The Deck Completion Set for this drawer kit requires modification when installed with an existing plastic load liner.   Consists of:1 x Front Runner Drawer unit (SSDR012)1 x Toyota Land Cruiser 79 DC Drawer Deck Completion Set (SSDS107)1 x Wing Set (SSWS004)1 x Push to Close latch with 2 keys per lock3 x Accessory Channels6 x Eye Nuts for Accessory ChannelsInstallation HardwareFitting InstructionsMaterials used:Aluminum - Accessory ChannelsBlack powder coated steel - Drawer Bins, Frame & Mounting ChannelsCarpeted & Laminated plywood - Top Deck & Deck SetsProduct Dimensions:Overall Closed Dimensions:1510mm (59.5") L x 1574mm (62") W x 335mm (13.2") HDrawer Internal Dimensions:1100mm (43.3") L x 747mm (29.4") W x 208mm (8.2") HWeight:80.5kg (177.5lbs)Load Rating:180kg (397lbs)

If Front Runner does not offer a vehicle specific drawer kit for your make and model vehicle, consider these “universal” drawers. Since this drawer will only fit into appropriately sized vehicles, please see SPECS for exact product measurements.Includes turnbuckles and carabiners to facilitate installation to many vehicle factory mounting points. 180kg / 397lb drawer load carrying capacity. Hold open feature: drawer “locks” open while parked on uneven surfaces. High-strength bearing slides allows the drawer to extend nearly 100% from the anchored base. Provide peace of mind and security by locking away important travel items such as computers, smart phones and camera gear. The flat deck incorporates three cargo attachment channels and 6 Tie Down Rings / Eye Nuts For Drawer System. Customize your own storage configurations. Stack and secure luggage, Wolf Pack Pro, Cub Pack, aluminum boxes and other storage containers to the top deck using Stratchit or other straps. The deck above the drawers can also be used to mount Front Runner Fridge/Cargo Slides. To create a removable box option, use Cub Pack or Flat Pack inside the drawers. The Cub Pack or Flat Pack can be used to further organize and easily move gear in and out of a vehicle. The deck is covered with a durable, UV resistant nylon pile carpet. The nylon carpet surface creates resiliency for securing cargo while insulating against noise and vibration. Finished with the same durable black powder coating as Front Runner Roof Racks and other Front Runner products. All Front Runner Storage Systems are backed by a 2 year warranty. NOTE: These "universal” drawers do not come with a vehicle specific deck completion set or faceplates.If you have any questions about whether or not this product will fit your vehicle, please contact Front Runner before purchase.*Please Note: Cub Packs and Flat Packs are not included when purchasing this Drawer System and are sold separately.   Consists of:1 x Medium Pick Up Drawer unit1 x Push to close latch with 2 keys3 x Accessory Channels6 x Eye Nuts for Accessory ChannelsInstallation HardwareFitting InstructionsMaterials used:Black powder coated steel - Drawer BinCarpet & Laminated plywood - Top DeckProduct Dimensions:Overall Dimensions:1170mm (46.1") L x 860mm (33.9") W x 295mm (11.6") HInternal Dimensions:1100mm (43.3") L x 747mm (29.4") W x 208mm (8.2") HOpen Dimensions:2100mm (82.7") L x 860mm (33.9") W x 295mm (11.6") HWeight:67.8kg (149.5lbs)Load Rating:180kg (137lbs)

More slats for more adventure. Add slats to customize your existing Front Runner Rack Tray. Create additional mounting points, a solid tray surface.   Transform your Slimline II rack tray into a semi-solid, or solid surface; for sleeping, sitting, additional support and / or extra mounting points. Includes Additional Tray Slat Bolts to secure extra slat to your Slimline II Rack Tray.This slat will work with any Front Runner Slimline II Rack that is 1575mm wide. Can also be used to build a custom Load Bar Kit, or as a replacement slat. Features T-slots on both the top and bottom faces. A slat's sliding nut T-slot allow for quick fitting and removal of a variety of accessories and equipment. Made from the same black powder coated aluminum as all Front Runner Racks. RRSAP1575 - 1575mm Slat Add-On KitConsisting of:1x RRAC045 - Additional Tray Slat Bolts1x RRSS1575 - 1575mm SlatMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 2.13kg (4.7lbs)Shipping Dimensions:Width: 115mm (5")Length: 1585mm (62")Height: 70mm (3")Shipping Weight:Weight: 2.45kg (5lbs)

More slats for more adventure. Add slats to customize your existing Front Runner Rack Tray. Create additional mounting points, a solid tray surface.   Transform your Slimline II Rack Tray into a semi-solid, or solid surface; for sleeping, sitting, additional support and / or extra mounting points. Includes Additional Tray Slat Bolts secure extra slat to your Slimline II Rack Tray. This slat will work with any Front Runner Slimline II Rack that is 1475mm wide. Can also be used to build a custom Load Bar Kit, or as a replacement slat. Features T-slots on both the top and bottom faces. A slat's sliding nut T-slot allow for quick fitting and removal of a variety of accessories and equipment.  Made from the same black powder coated aluminum as all Front Runner Racks. Consisting of:1x RRAC045 - Additional Tray Slat Bolts1x RRSS1475 - 1475mm Slat Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 2kg (4.41lbs)Shipping Dimensions:Width: 110mm (4")Length: 1480mm (58")Height: 70mm (3")Shipping Weight:Weight: 2.36kg (5lbs)

More slats for more adventure. Add slats to customize your existing Front Runner Rack Tray. Create additional mounting points, a solid tray surface.   Transform your Slimline II Rack Tray into a semi-solid, or solid surface; for sleeping, sitting, additional support and / or extra mounting points. Includes Additional Tray Slat Bolts to secure extra slat to your Slimline II Rack Tray. This slat will work with any Front Runner Slimline II Rack that is 1425mm wide. Can also be used to build a custom Load Bar Kit, or as a replacement slat. Features T-slots on both the top and bottom faces. A slat's sliding nut T-slot allow for quick fitting and removal of a variety of accessories and equipment. Made from the same black powder coated aluminum as all Front Runner Racks. Consisting of:1x RRAC045 - Additional Tray Slat Bolts1x RRSS1425 - 1425mm SlatMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 1.93kg (4.25lbs)Shipping Dimensions:Width: 110mm (4")Length: 1430mm (56")Height: 70mm (3")Shipping Weight:Weight: 2.26kg (5lbs)

More slats for more adventure. Add slats to customize your existing Front Runner Rack Tray. Create additional mounting points, a solid tray surface. Transform your Slimline II Rack Tray into a semi-solid, or solid surface; for sleeping, sitting, additional support and / or extra mounting points. Includes Additional Tray Slat Bolts to secure extra slat to your Slimline II Rack Tray. This slat will work with any Front Runner Slimline II Rack that is 1345mm wide. Can also be used to build a custom Load Bar Kit, or as a replacement slat. Features T-slots on both the top and bottom faces. A slat's sliding nut T-slot allow for quick fitting and removal of a variety of accessories and equipment. Made from the same black powder coated aluminum as all Front Runner Racks. Consisting of:1x RRAC045 - Additional Tray Slat Bolts1x RRSS1345 - 1345mm SlatMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 1.82kg (4.01lbs)Shipping Dimensions:Width: 110mm (4")Length: 1350mm (53")Height: 70mm (3")Shipping Weight:Weight: 2.17kg (5lbs)

Lightbar wind fairing for Toyota Land Cruiser Prado 250 (2024-Current) Slimsport Roof Rack Kit / Lightbar Ready or Lexus GX 550 (2024-Current) Slimsport Roof Rack Kit / Lightbar Ready. Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included Consists of:1 x Toyota Land Cruiser Prado / Lexus GX 550 (2024-Current) Slimsport Rack Wind Fairing Light Bar ReadyHardware KitFitment Guide Materials used:Black powder-coated steel Product Dimensions:1188mm (46.8") L x 194mm (7.6") W x 146mm (5.7") H Weight:3.3Kg (7.3lbs)

Smooth out the ride in your Toyota Land Cruiser Prado or Lexus GX 550 in more ways than one with the Slimsport Rack Wind Fairing. The Wind Fairing channels air fluidly over the rack and accessories to help reduce drag and wind noise. It mounts quickly to the front of your roof rack.   A wind fairing for the Toyota Land Cruiser Prado 250 (2024-Current) Slimsport Roof Rack Kit or Lexus GX 550 (2024-Current) Slimsport Roof Rack Kit . Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Toyota Land Cruiser Prado / Lexus GX 550 (2024-Current) Slimsport Rack Wind FairingHardware KitFitment Guide Materials used:Black powder-coated steel Product Dimensions:1188mm (46.8") L x 189mm (7.4") W x 133mm (5.2") H Weight:3.8Kg (8.4lbs)

Get ready to light up the night while reducing drag and noise with this 40” Light Bar Wind Fairing for the Slimsport Rack on your Subaru Outback GEN 6. It also improves fuel consumption when you have bulky items on the rack and its durable rubber beading, found on the bottom edge, gives added protection when going over rough terrain.   Lightbar wind fairing for Subaru Outback GEN 6 (2020-Current) Slimsport Roof Rack Kit / Lightbar Ready. Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber beading is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Subaru Outback Slimsport Rack Light Bar Wind Fairing1 x Wind Fairing Rubber - 950mm (L)1 x Clear VinylInstallation HardwareFitting Instructions Materials used:Black powder-coated high strength steel Product Dimensions:73mm (2.9") L x 1145mm (45.1") W x 206mm (8.1") H Weight:2.99Kg (6.6lbs)

Reduce noise levels and improve the airflow over the Slimsport Roof Rack of your Subaru Outback GEN 6 with this easy-to-fit Wind Fairing. It certainly helps reduce fuel consumption on a loaded rack and its durable rubber beading, found on the bottom edge, gives added protection when going over rough terrain.   A wind fairing for the Subaru Outback GEN 6 (2020-Current) Slimsport Roof Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber beading is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Subaru Outback Slimsport Rack Wind Fairing1 x Wind Fairing Rubber - 950mm (L)1 x Clear VinylInstallation HardwareFitting Instructions Materials used:Black powder-coated high strength steel Product Dimensions:79mm (3.1") L x 1145mm (45.1") W x 201mm (7.9") H Weight:3.53Kg (7.8lbs)

Enjoy a much quieter ride in your Volkswagen T5/T6/T6.1 with this Slimsport Rack Wind Fairing. It seamlessly channels air up and over the rack, reducing noise and fuel consumption. A wind fairing for the Volkswagen T5/T6/T6.1 Transporter SWB (2003-2024) Slimsport Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Volkswagent T5/T6/T6.1 Slimsport Rack Wind FairingInstallation HardwareFitting Instructions Materials used:Black powder coated steel Product Dimensions:1344mm (52.9") L x 185mm (7.3") W x 155mm (6.1") H Weight:2.3kg (5.1lbs)

Improve aerodynamics and enjoy a quieter ride on your loaded Toyota Sequoia with the specially-designed Slimsport Rack Wind Fairing. This innovative accessory reduces drag and minimizes wind noise by efficiently channeling air over your Slimsport Roof Rack. This particular model features a 40" cutout to allow the use of the Front Runner 40" Light Bar, so you can keep exploring even after the sun goes down.   Lightbar wind fairing for the Toyota Sequoia (2023-Current) Slimsport Roof Rack Kit / Lightbar Ready. Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Toyota Sequoia 40" light bar wind fairingFitment Guide Installation Hardware  Materials used:Black powder-coated high strength steel Product Dimensions:1281mm (50.4") L x 169mm (6.7") W x 172mm (6.8") H  Weight:4kg (8.8lbs)

Enhance the aerodynamics of your Toyota Sequoia and experience a smoother, quieter ride when you’re hauling loads with the purpose-built Slimsport Rack Wind Fairing. This innovative accessory is designed to minimize drag and reduce wind noise by effectively directing airflow over your Slimsport Roof Rack (and the gear loaded on it).   A wind fairing for the Toyota Sequoia (2023-Current) Slimsport Roof Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Toyota Sequoia (2023-Current) Slimsport Rack Wind Fairing1 x Fitting InstructionsInstallation Hardware Materials used:Black powder coated high strength steelStainless steel fasteners Product Dimensions:1311mm (51.6") L x 241mm (9.5") W x 143mm (5.6") H Weight:4.2kg (9.3lbs)

Improve the performance and aerodynamics of your Toyota Land Cruiser 100 Series Slimsport Roof Rack with this premium Wind Fairing. Designed to direct airflow smoothly over the roof rack and mounted accessories, it helps reduce wind noise and drag while driving. Ideal for vehicles carrying bulky gear, the wind fairing can assist in improving fuel efficiency by minimizing aerodynamic resistance. A durable rubber blade is fitted along the lower edge to help seal gaps between the roof and fairing, while also protecting the roof surface when travelling over rough terrain. Manufactured from high-strength steel with a durable black powder-coated finish, this wind fairing is built to withstand harsh Australian conditions and integrates seamlessly with the Slimsport Roof Rack system. Features Designed specifically for the Toyota Land Cruiser 100 Series Slimsport Roof Rack Kit. Reduces wind noise and aerodynamic drag. Helps improve fuel efficiency when carrying roof-mounted cargo. Durable rubber edge seal helps protect the vehicle roof. Improves airflow over roof rack accessories and cargo. Constructed from high-strength steel. Black powder-coated finish for long-lasting corrosion resistance. Includes mounting brackets and installation hardware. What's Included 1 x Toyota Land Cruiser 100 Series Wind Fairing Installation Hardware Fitment Guide Specifications Material Black Powder-Coated High-Strength Steel Dimensions 17.8 cm (L) x 128.5 cm (W) x 19.7 cm (H) Weight 3.8 kg Vehicle Compatibility TOYOTA LAND CRUISER 100 SERIES (1998-2007) 4.2L Turbo Diesel (HDJ100) TOYOTA LAND CRUISER 100 SERIES (1998-2007) 4.7L Petrol V8 (UZJ100 / UZJ100R)

Reduce the drag and wind noise over the roof rack of your Toyota Rav4 with a wind fairing. The Slimsport Rack Wind Fairing channels air fluidly over your Slimsport Roof Rack (and the accessories loaded on it) to help reduce fuel consumption. It mounts quickly to the front of your roof rack and adds an overall bolder look.   A wind fairing for the Toyota Rav4 (2019-Current) Slimsport Roof Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Toyota Rav4 Slimsport Rack Wind Fairing1 x Protection StripInstallation HardwareFitting Instructions Materials used:Black powder coated steel Product Dimensions:1175mm (46.3") L x 172mm (6.8") W x 203mm (8") H Weight:3.25kg (7.2lbs)

Smooth out the ride in your Subaru XV Crosstrek in more ways than one with the Slimsport Rack Wind Fairing. The Wind Fairing channels air fluidly over the rack and accessories to help reduce drag and wind noise. It mounts quickly to the front of your roof rack and adds an overall bolder look.   A wind fairing for the Subaru XV Crosstrek 2nd Gen (GT) (2017-2023) Slimsport Roof Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Subaru XV Crosstrek 2nd Gen (GT) (2017-2023) Slimsport Rack Wind Fairing1 x Protection StripInstallation HardwareFitting Instructions Materials used:Black powder coated steel Product Dimensions:1140mm (44.9") L x 171mm (6.7") W x 129mm (5.1") H Weight:2.89kg (6.4lbs)

Don’t let darkness throw shade on your adventures. Keep exploring after nightfall with the 10" LED Light Bar. The high-performance LEDs with OSRAM technology, throw 1500 lumens over 37m. It features an intelligent reflector design that diverts the light from the LEDs so that oncoming traffic is not directly exposed to the light; as well as an additional yellow cover, that won’t attract insects to your campsite.   The high-performance LEDs, with OSRAM technology, reach a distance of 37m and deliver 1500 lumens. The 3000 Kelvin intensity is distributed as a flood beam pattern. The intelligent reflector design diverts the light from the LEDs so that oncoming traffic is only indirectly exposed to the light. Perfect to light up your campground, this Light Bar with the additional yellow cover, also won’t attract pesky insects to your site. The integrated driver and thermal management system measures and regulates the temperature of the LED, eliminating the risk of overheating and aiding in the longevity of its lifespan. Full LED polarity protection automatically breaks the circuit in the event of excess voltage, which ensures a long lifespan. The 12V/24V LED lightbar is ECE-compliant and versatile in application and is not limited to automotive use only. Individual installation is possible due to the Double ECE certification (Double ECE-Certification: R112). The Light Bar is approved according to ECE regulations and may therefore be installed and operated on public roads. In addition to the ECE approval, individual special regulations and legislation of the countries must be observed. Installs easily into the front, back or side profiles of your Slimline II Rack, or to the side of the Slimsport Rack with 10" LED Light Bar VX250-FL Mounting Bracket. The mounting bracket includes side guards to protect the 10" LED Light Bar VX250-FL / 12V/ 24V / Flood Light from potential damage caused by flying rocks and other road debris. Fitment guide and installation hardware included. Note: When powering your light, ensure your power cord is installed into the light before plugging it into the power source. Disconnecting would need to be done from the power source then the light.

The Slimsport Rack Wind Fairing is specifically designed to pair with the 40” Front Runner Light Bar for a sleek look and even more functionality. After all, adventures don't end just because the sun goes down.   Light Bar Wind Fairing for the Toyota Rav4 (2019-Current) Slimsport Roof Rack Kit Allows installation of Front Runner 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount Designed to direct airflow over the rack and accessories, reducing drag and wind noise Helps reduce fuel consumption while carrying bulky loads Durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain Brackets and installation hardware included Consists of:1 x Toyota Rav4 Slimsport Rack 40" Light Bar Wind FairingInstallation HardwareFitting Instructions Materials used:Black powder coated steel Product Dimensions:1175mm (46.3") L x 178mm (7") W x 161mm (6.3") H Weight:4.94kg (10.9lbs)

Securely mount your 40" LED Light Bar (VX1000-CB) to the front or underneath your Front Runner Roof Rack with this Single Mount bracket. These brackets feature a protective cover to shield the light bar against small rocks.   Two sets of brackets that secure the 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount to the Front Runner Roof Rack. Front Rack mounting brackets secure this light bar using the top T-slots of the front combined slat side profile, while the Under Rack mounting brackets secure it using the bottom T-slot of the front combined slat profile. It comes with a robust front cover to protect the LED light bar from small rocks. All components are made of steel and aluminum and sealed with the same durable, weather-resistant black powder coating as the Front Runner Roof Racks. Includes all installation hardware and fitting instructions. Consists of:1 x Set of Front Mount Brackets (1 Left Hand side & 1 Right Hand side)1 x Set of Underneath Mount Brackets (1 Left Hand side & 1 Right Hand side)1 Front CoverInstallation HardwareFitting InstructionsMaterials used:Black powder coated steelProduct Dimensions:1070mm (42.1")L x 102mm (4")W x 58mm (2.3")HWeight:2.8kg (6.2lbs)

Seamlessly integrate the Slimsport Rack Fairing specifically designed to pair with the 40” Front Runner Light Bar for a sleek look and even more functionality. After all, adventures don't end just because the sun goes down.   Lightbar wind fairing for . Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Consists of:1 x Slimsport Rack 40" Light Bar Wind Fairing1 x Protection StripInstallation HardwareFitting InstructionsMaterials used:Black powder coated steel Product Dimensions:1140mm (44.9") L x 163.5mm (6.4") W x 116mm (4.6") H Weight:2.1kg (4.6lbs)

Make a statement and change the standard Front Runner rack Wind Deflector to this bold Front Runner Wind Fairing for Low Profile rack kits. Quickly mounts to the front of your roof rack to help move air over large rack loads and accessories, while reducing wind noise at high speeds. Get a bold new overlanding look in minutes. Create a solid appearance by covering the gap from roof to rack. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. Easily secures to your roof rack in three simple steps. Adjustable brackets allow the Wind Fairing to be correctly angled and positioned on your vehicle. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. An optional clear protective strip is included to eliminate any potential rare minor scuffing caused by heavy dust. Consists of:1 x Wind Fairing4 x Brackets1 x Rubber BladeInstallation HardwareFitting instructions Materials used:Black powder coated aluminumEPDM Rubber Product Dimensions:1087mm(42.8") L x 2mm(0.1") W x 127mm(5") H Weight:1.5kg (3.3lbs)

It’s raining, it’s pouring and you’re still out exploring. Ready for extreme weather, the heavy-duty Typhoon Bag is 100% water and dustproof. It easily adapts its size to fit anything from clothes or camping supplies to the Front Runner Cub Pack or Flat Pack storage containers. Declutter the interior of your vehicle with this roof-rack ready bag that’s designed to keep all your gear clean and dry while you adventure on- and off- road.   Versatile storage solution for small to large cargo. Simply roll the bag to perfectly fit the size of the contents. Free up precious interior space by attaching it to a Front Runner Rack. Scalable up to 90L (5492 in³) capacity. Expands to hold 2 Cub Pack*. Removable tray makes packing a breeze and protects the bag from chaffing when carried on a roof rack. Soft Grip side handles. Bag can be secured to the roof rack using a pair of Stratchits*. Roll-top style bag with sonically welded seams is 100% water and dust proof. Integrated air-pressure release valve for a water tight seal when rolling and sealing the bag. Conforms with an IP66 rating which provides assurance of a completely sealed and dust-resistant enclosure, as well as protection from high-pressure water streams. Made with innovative heavy-duty waterfproof materials. Protects contents from sun, wind, rain, and water crossings. Durable and ready for intense continuous use. Endless storage uses from clothes and scuba gear to climbing and camping gear. Folds compact for easy storage when not in use. *Stratchits, Flat Packs and Cub Packs sold separately. Consists of:1 x 90L (5492 in³) Typhoon Wet/Dustproof Transit Bag1 x Internal Base Tray Materials used:1000D PVC coated TPE - Base500D PVC coated TPE - Main BodyBallistic Nylon - StrapsFormed PU with Nylon cover - Base Tray Finishes:Black with Grey detailed double stitching Product Dimensions:660mm (26") L x 450mm (17.7") W x 500mm (19.7") H (Opened)660mm (26") L x 450mm (17.7") W x 250mm (9.8") H (Closed) Weight:2.3kg (5.1lbs)Special NotesSKU; F0002

Free up interior space with this sturdy, flexible, lightweight and large roof top storage bag. Ideal for clothes, camping gear, Front Runner Wolf Pack and Cub Pack storage containers, and whatever else would normally be carried in your trunk or cabin.   Manufactured from a durable 600d fabric which is 100% UV protected, dust proof and water resistant. Nylon stitching ensures no rotting or deterioration when exposed to the elements. Overlapping fabric lip with velcro seal to protects heavy duty zipper from dust and debris. 1100g PVC base is built to withstand the toughest journeys on top of the roof. 6 Triple-stitched tags for looping through Stratchits (or similar straps) and securing the bag to a Front Runner roof rack or other cargo carriers. 2 rubber-molded carry handles make for easy transport to your camp or lodging and hassle-free handling when loading or removing from the roof top. 1050mm / 41.3 in width. Designed to fit 2 Wolf Pack, up to 3 Cub Pack, or up to 2 Flat Pack. Folds compact. Consists of:1 x Large Transit BagMaterial used:600d CanvasProduct Dimensions:Open Dimensions:1050mm (41.3") L x 440mm (17.3") W x 300mm (11.8") HFolded Dimensions:470mm (18.5") L x 330mm (13") W x 50mm (2") HWeight:1.46kg (3.4lbs)

Front Runner's Adjustable Rack Cargo Chocks can be used to brace and secure a variety of gear on a Front Runner Rack. These chocks wedge against and secure the corners or sides of your gear to prevent movement and rattling. Adjustable along the slats to resize and fit a variety of gear like the Wolf Pack Pro, Cub Pack, Typhoon Bag, Expander Camping Chair, and water tanks. Secures to your rack using Eye Nuts and supplied hardware. Eye Nuts create lashing points to secure cargo using Stratchits* *Note: Purchase Wolf Packs, Cub Packs, Stratchits etc. separately.   Consists of:4 x Rack Cargo Chocks4 x Eye NutsInstallation HardwareFitting InstructionsMaterials used:Black powder coated steelProduct Dimensions:100mm (3.9") L x 82mm (3.2") W x 42mm (1.7") H (Per Bracket)Weight:1.04kg (Per Set of 4)

LED flood light for illumination around vehicle and campsite. Comes standard with Front Runner custom tiltable bracket for fitting to the front, side or rear of the Roof Rack.   LED flood light for illumination around vehicle and campsite. Comes standard with Front Runner tiltable mounting bracket for fitting to the front, side or rear of the Roof Rack. Powered by power cord from vehicle 12v accessory outlet (Hella Extension Cord - 3m/10'). Bracket has power inlet and outlet to power light and additional 12v accessories simultaneously. Special regulations and legislation within each country should be taken into consideration before use. Note: For compatibility with the Slimsport or Slimpro Van Rack the Slimsport Side Mount Accessory Bracket / Small, is required. *sold separatelyNote: When powering your light, ensure your power cord is installed into the light before plugging it into the power source. Disconnecting would need to be done from the power source then the light.   7 Watt Square LED Light Specifications:Input Voltage: 9-32 Volts DCPower Consumption: 27 WattsAmperage Draw: 2.1 Amps @ 12 VLumen Output: Approx. 1700Beam Pattern: Flood PatternBeam Angle: 60 Degree FloodHousing Material: AluminumMounting Bracket: Steel powder coatedLens Material: Polycarbonate Dust Proof, Water Proof!

The lockable stainless steel cage keeps your axe head safe and out of the way when mounted to the side of the Front Runner Slimline II Roof Rack.  Super simple installation – just slide the bolts and brackets into the side rail of the Slimline II Roof Rack Tray and tighten.

Up your Toyota Tundra’s gear-carrying capacity in the load bed area with our Pro Bed Rack Kit. Includes a Slimline II Roof Rack and Pro Bed System that is secured to the bed of your Toyota. Attach various Pro Bed accessories to the Pro Bed System, while all our 55+ available other accessories can go on the rack—no more excuses for leaving any gear behind. This Pro Bed Rack Kit is specifically designed to fit the Toyota Tundra (3rd Gen) 4 Door CrewMax 5.5 load bed. Included in this Kit is the a 1425mm/56.1" x 1560mm/61.4" Slimline II Rack and Pro Bed System. The Pro Bed Rack Kit provides the freedom to customize your Load Bed storage configuration. The Slimline II Rack allows all the top, side and under rack mounted adventure gear accessories.  The Wolf Pack Pro Cargo System Bracket/Twin Wolf Pack Pro Cargo System Bracket, Pro Bed Rack Headboard Molle Panel and a Pro Bed Universal Accessory Mount freeing up space on the Slimline II rack and in the bed of your truck. Secures to the bed of the Toyota Tundra (3rd Gen) 4 Door CrewMax 5.5 with specific mounting brackets. Drilling is required for fitment.  The Pro Bed System has integrated fixing points for more accessories such as the Pro Bed Tailgate Net. All Front Runner Racks are backed by a Limited Lifetime Warranty* For further information on installation, please see the fitment instructions in the INSTALL tab. Consisting of:3x FASS025 - Foot Set / 70mm - 80mm1x PBTT002S - Toyota Tundra (3rd Gen) 4 Door CrewMax 5.5' (2022-3x RRAC921 - Canopy Rack Kit Installation Set1x RRSTG08 - SLII Tray - 1345mm(W)X1560mm(L)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 79kg (174.16lbs)Shipping Dimensions:Width: 645mm (25")Length: 1720mm (68")Height: 500mm (20")Shipping Weight:Weight: 85kg (187lbs)

Turn your Ford-150 into the ultimate gear carrier with the Pro Bed Rack System and a Slimline II Rack. Now you can enjoy easy side access to all the Pro Bed Pro Bed Rack-specific accessories, such as the Molle Panel and Recovery Device Mount, while taking advantage of the extra free space in the load bed. Customize your Slimline II Rack for any adventure thanks to the 55 plus available rack accessories. This Pro Bed Rack Kit is specifically designed to fit the Ford F-150 6.5' load bed. Included in this Kit is the a 1425mm/56.1" x 1964mm/77.32" Slimline II Rack and Pro Bed System. The Pro Bed Rack Kit provides the freedom to customize your Load Bed storage configuration. The Slimline II Rack allows all the top, side and under rack mounted adventure gear accessories.  The Pro Bed System secures Pro Bed accessories, Wolf Pack Pro Cargo System Bracket/Twin Wolf Pack Pro Cargo System Bracket,Pro Bed Rack Headboard Molle Panel and a Pro Bed Universal Accessory Mount freeing up space on the Slimline II rack and in the bed of your truck. Secures to the bed of the Ford F-150 6.5' with specific mounting brackets. Drilling is required for fitment.  The Pro Bed System has integrated fixing points for more accessories such as the Pro Bed Tailgate Net. All Front Runner Racks are backed by a Limited Lifetime Warranty*For further information on installation, please PBFF004T - Ford F-150 6.5' Bed (2009-Current) Pro Bed Rack Kit Consisting of:4x FASS025 - Foot Set / 70mm - 80mm1x PBFF004S - Ford F-150 6.5" Bed (2009-Current) Pro Bed System1x RRSTJ10 - SLII Tray - 1425mm(W)X1964mm(L) Material Used:Black epoxy powder - coated T6 aluminiumInstalled height from load bed ledge:640mm/ 25.19" Approximate Installed Weight: 83kg (182.98lbs) Shipping Dimensions:Width: 640mm (25")Length: 1820mm (72")Height: 490mm (19") Shipping Weight:Weight: 83kg (183lbs)

Now you can smartly secure two Wolf Pack Pro boxes to the side of the Pro Bed System and Rack kit with this adjustable Pro Cargo System Bracket. The strong steel powder-coated brackets ensure quick access to your plastic storage boxes. This Pro Cargo System bracket secures two (2) Wolf Pack Pro Wolf Pack Pro's (sold separately) to the side of the Pro Bed System and Pro Bed Rack Kit. The Wolf Pack Pro is side-mounted, allowing quick and easy access to all your adventure gear while keeping it safe from the elements. The brackets are adjustable from 1415mm(55.7") - 1555mm(61.2"). Made of high-strength steel and sealed with the same durable, weather-resistant powder coating as the Front Runner Racks. The top and bottom latches are lockable with a Rack Accessory Lock / Small(sold separately), preventing unwanted access. These brackets are suitable for Wolf Pack Pro Wolf Pack Pro's when when fitted with the Wolf Pack Pro Hi-Lid Wolf Pack Pro Hi-Lid. No drilling is required for the installation of these brackets. Note: This Twin Wolf Pack Pro Cargo System Bracket is not compatible with the Ford Ranger T6 Wildtrak/Raptor Double Cab (2012-2022) Pro Bed System or the Ford Ranger T6 Wildtrak/Raptor Double Cab (2012-2022) Pro Bed Rack Kit.   Consists of:2 x Wolf Pack Pro Mounting BracketsHardware KitFitting InstructionsMaterials used:Black powder coated high strength steelProduct Dimensions:1415mm (55.7")-1555mm (61.2") L x 335mm (13.2") W x 260mm (10.2") HWeight:13Kg (28.7lbs)

Brighten up the road ahead and extend your adventures into the later hours with the 10” LED Light Bar. The light bar is constructed for durability and designed for versatility, both mounted onto Front Runner roof racks and for other off-vehicle uses. Six high-performance LEDs provide better visibility with 2520 raw lumen and 6000 kelvin color. Provides 120 degree flood beam pattern for close but wide range illumination immediately surrounding the vehicle. This auxiliary light is equipped with a robust polycarbonate lens set in a die cast aluminum housing. The 12V/24V LED Light Bar is versatile in application and is not limited to automotive use only. Special regulations and legislation within each country should be taken into consideration before use. Expected LED life of 30,000 hours. Secures to your Front Runner roof rack with the LED 10inch Light Bar Bracket.   Consists of:1 x 10" Light Bar1 x Bracket Set Materials used:Diecast aluminum housingPolycarbonate lensZinc alloy brackets Product Dimensions:Light Bar:270mm (10.6") L x 58mm (2.3") W x 56mm (2.2") H Light Bar with supplied bracket:270mm (10.6") L x 58mm (2.3") W x 70mm (2.8") H Weight:17.4 kg (38.4lbs) Special Notes:6pcs*5w high intensity CREE LEDSPower Consumption: 30WOperating Voltage: 10-30 DCWaterproof rate: IP 67Raw Lumen: 2520lmEffective lumen: 1740lmCurrent draw:12V/2.40A；24V/1.12ALife span:30000HColor Temperature: 6000K

Keep your adventure going after the sun sets with this 10” LED Light Bar. The ECE compliant high performing LED creates a strong 3000 Kelvin flood beam pattern so your trail will always be well-lit.   The high-performance LEDs, with OSRAM technology, reach a distance of 37m and deliver 1500 lumens. The 3000 Kelvin intensity is distributed as a flood beam pattern. The intelligent reflector design diverts the light from the LEDs so that oncoming traffic is only indirectly exposed to the light. Perfect to light up your campground, this Light Bar with the additional yellow cover, also won’t attract pesky insects to your site. The integrated driver and thermal management system, measures and regulates the temperature of the LED, eliminating the risk of overheating and aids in the longevity of its lifespan. Full LED polarity protection automatically breaks the circuit in the event of excess voltage, which ensures a long lifespan.The 12V/24V LED lightbar is ECE-compliant and versatile in application and is not limited to automotive use only. Individual installation is possible due to the Double ECE certification (Double ECE-Certification: R112). The Light Bar is approved according to ECE regulations and may therefore be installed and operated on public roads. In addition to the ECE approval, individual special regulations and legislations of the countries must be observed. Secures to your Front Runner Roof Rack with 10" LED Light Bar VX250-FL Mounting Bracket. Connect you 10" LED Light Bar VX250-FL / 12V/ 24V / Flood Light to a Roof Rack Power Point*, powered by Hella Extension Cord - 3m/10'* power cord from your vehicles 12V accessory outlet. *Note: The Roof Rack Power Point and Hella Extension Cord - 3m/10' are sold separately.Note: When powering your light, ensure your power cord is installed into the light before plugging it into the power source. Disconnecting would need to be done from the power source then the light.   Consists of:1 x Lightbar1 x Yellow cover1 x Bracket set1 x Bolt Kit Product Dimensions:Light Bar:275mm (10.8") L x 67mm (2.6") D x 35mm (1.4") H Light Bar with supplied bracket:328mm (12.9") L x 67mm (2.6") D x 55mm (2.2") H Weight:875g (27.3oz) Special Notes:Product type: On-road and off-roadSKU: LEDWL 115-FLFRLED supplier: OSRAMLumens: 150012/24V30W2.5 AmpsColor temperature: 3000 KLifespan Tc: 5000 hGuarantee: 5 yearsDouble ECE-Certification: R112

Driving in the dark? The MX85-SP is a strong, reliable, LED high-beam headlight. The far field illumination makes it ideal to brighten any adventure.   Four (4) high-performance LED working light reaches a distance of 110m at a 13.5 degree angle with a color temperature of 6000 Kelvin producing daylight lighting conditions. Dual lighting functions include the classic working light with up to 1250 lumen, and the other is a stylish X shape LED working. Polycarbonate lens, durable to withstand off-road conditions. Full LED high beam polarity protection automatically breaks the circuit in the event of over-voltage, which ensures a long lifespan. Equipped with an integrated driver and thermal management system, eliminating the risk of overheating. 12V compatibility for diverse requirements and vehicles from off-road to recreational and agricultural. Special regulations and legislation within each country should be taken into consideration before use. Secures to your Roof Rack with 4" LED OSRAM Light Cube MX85-WD/MX85-SP Mounting Bracket. Optional LED Light Bar Wire Harness AX 2LS or LED Light Bar Wire Harness AX 1LS are available and sold separately. Note: These powerful working lights are permitted only for off-road applications and must not be used on public roads.Note: When powering your light, ensure your power cord is installed into the light before plugging it into the power source. Disconnecting would need to be done from the power source then the light.   Consists of:1 x Light cube with bracket1 x Bolt Kit Dimensions:Light cube:85mm (3.3") L x 57mm (2.2") W x 85mm (3.3") H Light cube with supplied bracket:85mm (3.3") L x 57mm (2.2") W x 121.5mm (4.8") H Weight:500g (17.6oz) Special Notes:Product type: Off-roadSKU: LEDDL101-SP / 4052899526532Lumens: 125012V22/2W1.83/0.17 AmpsColor temperature: 6000 KLifespan Tc: 5000 hGuarantee: 5 years

Driving on difficult terrain? The MX85-WD, is a strong, reliable, LED high-beam headlight. The near field illumination makes it ideal to navigate off-road trails.   Dual lighting functions include LED working light and the LED working spotlight that provides stylish X shape light. Light beam reaches a distance of 55m at a 43.5 degree angle and delivers a luminosity of 1250 lumens. Polycarbonate lens, durable to withstand off-road conditions. Features an over and under voltage protection up to 18 volts. Equipped with an integrated driver and thermal management system, eliminating the risk of overheating. Excellent compatibility for diverse requirements and vehicles from off-road to recreational and agricultural. Special regulations and legislation within each country should be taken into consideration before use. Secures to your Front Runner Roof Rack with 4" LED OSRAM Light Cube MX85-WD/MX85-SP Mounting Bracket. Optional LED Light Bar Wire Harness AX 2LS or LED Light Bar Wire Harness AX 1LS are available and sold separately. Note: These powerful working lights are permitted only for off-road applications and must not be used on public roads.Note: When powering your light, ensure your power cord is installed into the light before plugging it into the power source. Disconnecting would need to be done from the power source then the light.   Consists of:1 x Light cube with bracket1 x Bolt Kit Product Dimensions:Light cube:85mm (3.3") L x 57mm (2.2") W x 85mm (3.3") H Light cube with supplied bracket:85mm (3.3") L x 57mm (2.2") W x 121.5mm (4.8") H Weight:500g (17.6oz) Special Notes:Product type: Off-roadSKU:LEDDL101-WDLumens: 125012V22/2W1.83/0.17 AmpsColor temperature: 6000 KLifespan Tc: 5000 hGuarantee: 5 years