HERTZ Cento Power 700W 1 Channel Amplifier (Cp 1.700)
$799.99
Enhance your audio system with the Hertz CENTO POWER CP 1.700, a mono amplifier that combines superior power handling and sophisticated sound control technologies. Boasting a superior power-to-size ratio with an efficiency of over 89%, this amplifier accommodates a broad voltage range, suitable for both conventional and electric vehicles. The CP 1.700 steps up with additional sound customization features, including a variable phase control to fine-tune the audio output to your preferences. Its high-noise rejection and balanced input circuitry maintain the integrity of the sound, while the inclusion of a full-range pre-out ensures flexible system expansion. Designed for durability and performance, the CP 1.700's elegant design and accessible top panel controls make it a top choice for audiophiles looking to push the limits of their car's audio system.
Channels
1
Amp class
D
POWER SUPPLY
Nominal power supply voltage (fuse)
11 ÷ 15 VDC (2 x 25 A)
Operating power supply voltage
9 ÷ 18 VDC
Idling current
1.10 A
Standby current draw
4.5 uA
Consumption, MIN load impedance (Max Musical Power)
33 A
Remote IN
4 ÷ 17 VDC (1 mA)
ART - Automatic Remote Turn on/off from SPK-IN (BTL radio only)
1.5 VDC
Efficiency
89%
AMPLIFIER STAGE
Distortion - THD @ 100 Hz, 70% Rated Power
0,01 %
Damping factor @ 1 kHz, 1W
350
Bandwidth @ -3 dB
10 Hz ÷ 500 Hz
S/N ratio (A-weighted @ 1 V Input)
113 dBA
Minimum load impedance
@ 1 Ch:
2 Ω
Adjustable Crossovers
yes
Output Power
Output power (RMS) @ 1% THD:
1Ch @ 4Ω
400 W x 1
1Ch @ 2Ω
700 W x 1
Total Power
700 W
Inputs
Pre-In / Speaker-In
Pre Out
Hi-Pass 50 ÷ 250Hz @ 12 dB/Oct.
Pre-In sensitivity
0.32 ÷ 8 VRMS
Speaker-In sensitivity
1.6 ÷ 40 VRMS
Sub Ch Lo-Pass
OFF / 50 ÷ 250 Hz @ 24 dB/Oct.
Bass Boost 50Hz
0 ÷ 9 dB
Subsonic Hi-Pass
OFF / 25 Hz @ 24 dB/Oct.
Sub Remote Volume Control
-20 ÷ 6 dB (Active on Rear Ch with LPF ON)
Weight
Kg
lbs
2.44
5.37
HERTZ Cento Power 1200W 1 Channel Amplifier (Cp 1.2K)
$1,099.99
Step into a world of refined bass with the Hertz CENTO POWER CP 1.2K This mono amplifier is engineered for high efficiency, reaching an efficiency greater than 89% within a compact, robust aluminum diecast casing. The CP 1.2K is designed to integrate seamlessly into both traditional and modern vehicle setups, thanks to its Universal Speaker Simulator and a wide operating voltage range suitable for electric vehicles. It features advanced noise rejection capabilities to ensure crystal-clear sound quality. With adjustable input levels, a low-pass crossover filter, a bass boost, and a subsonic filter, this amplifier allows for precise customization of your sound, making it an ideal choice for those seeking powerful, immersive bass without compromise.
Channels
1
Amp class
D
POWER SUPPLY
Nominal power supply voltage (fuse)
11 ÷ 15 VDC (2 x 35 A)
Operating power supply voltage
9 ÷ 18 VDC
Idling current
0.85 A
Standby current draw
4.5 uA
Consumption, MIN load impedance (Max Musical Power)
50 A
Remote IN
4 ÷ 17 VDC (1 mA)
ART - Automatic Remote Turn on/off from SPK-IN (BTL radio only)
1.5 VDC
Efficiency
89%
AMPLIFIER STAGE
Distortion - THD @ 100 Hz, 70% Rated Power
0,03 %
Damping factor @ 1 kHz, 1W
140
Bandwidth @ -3 dB
10 Hz ÷ 500 Hz
S/N ratio (A-weighted @ 1 V Input)
102 dBA
Minimum load impedance
@ 1 Ch:
2 Ω
Adjustable Crossovers
yes
Output Power
Output power (RMS) @ 1% THD:
1Ch @ 4Ω
650 W x 1
1Ch @ 2Ω
1200 W x 1
Total Power
1200 W
Inputs
Pre-In / Speaker-In
Pre Out
Hi-Pass 50 ÷ 250Hz @ 12 dB/Oct.
Pre-In sensitivity
0.32 ÷ 8 VRMS
Speaker-In sensitivity
1.6 ÷ 40 VRMS
Sub Ch Lo-Pass
OFF / 50 ÷ 250 Hz @ 24 dB/Oct.
Bass Boost 50Hz
0 ÷ 9 dB
Subsonic Hi-Pass
OFF / 25 Hz @ 24 dB/Oct.
Sub Remote Volume Control
-20 ÷ 6 dB (Active on Rear Ch with LPF ON)
Weight
Kg
lbs
2.44
5.37
HERTZ Spl Show 8" Woofer Component - Pair (Sv 200L)
$439.99
The Hertz SV 200L car audio woofers was designed to offer superior performance in terms of both thermal and mechanical capability. The target has been fully hit since the woofer features a pure copper voice coil wound on KSV former, an oversized magnet and a vented bottom plate. The SV 200L employs the proprietary V-cone technology with the cone constructed from pulp with cotton fibre as well as Lossless Polymer Rubber Surround, offering a powerful low frequency response as well as the best off-axis dispersion.
Component
SPL Woofer
Size mm (in.)
200 (8)
Power Handling - Continuous W
250
Power Handling - Peak W
500
Impedance Ohm
4
Voice Coil Ø
50 (2)
Frequency Response Hz
45 ÷ 4,5k
Magnet size D x d x h mm (in.)
120 x 60 x 20 (4.7 x 2.4 x 0.8)
Weight of one speaker kg (lb.)
2,32 (5.1)
Magnet
High density flux ferrite
Cone
Ultra light, non pressed paper
D mm
168
Re Ohm
3
Fs Hz
44
Le mH
0,75
Vas I
29
Mms g
31,5
Cms mm/N
0,42
BL T*m
8,6
Qts
0,33
Qes
0,36
Qms
3,32
Spl dB
94,5
A
209 mm
8.3 in.
B
178 mm
7 in.
C
91 mm
3.6 in.
D
82 mm
3.2 in.
HERTZ Spl Show 15" 2400W 2 Ohm Dvc Subwoofer (Ss...
$804.99
SS 15 D2 subwoofers featuring 38 cm (15 in.) cone is eager to thrill the enthusiasts with their power.The suspension system reinforced with progressive double-layer spiders keeps the performance constant over time, especially in the heavy use typical of Bass Wars events.Heat dissipation is essential for this type of use and has been maximized thanks to an accurate design. The use of a robust 75 mm (3 in.) dual winding (2 + 2 Ω) voice coil developed in 4-layer configuration on a support with venting holes allows the SS 15 D2 to manage the impressive 2400 W peak power! The basket has been designed for optimal thermal dissipation and high mechanical resistance.The non-pressed paper cone with the addition of cotton fiber is the ideal compromise between stiffness and lightness, essential for a high sensitivity value. Suspension and leadwires are oversized to withstand the very high excursions generated by the massive ferrite engine.Push connectors accept cables with cross-section up to 12 AWG, for a practical and safe connection, suitable for the high currents involved.
Size mm (in.)
380 (15)
Power Handling - Continuous W
1200
Power Handling - Peak W
2400
Impedance Ohm
2+2
Depth mm (in.)
210 (8.27)
Voice Coil Type
dual
No Filter Component
SPL DUAL COIL SUBWOOFER
Voice Coil Ø
75 (3)
Magnet size D x d x h mm (in.)
180 x 90 x 40 (6.69 x 3.54 x 1.57)
Weight of one component kg (lb.)
10,1 (22.27)
Magnet
Ferrite
Cone
Non pressed paper with cotton fibre
Xmech mm (in.)
20,7 (0.81)
D mm
323
Xmax mm
15,4
Re Ohm
0,96
Fs Hz
31
Le mH
1
Vas I
68,83
Mms g
361
Cms mm/N
0,07
BL T*m
10
Qts
0,61
Qes
0,66
Qms
7,4
Spl dB
88
A
390 mm
15.35 in.
B
353 mm
13.9 in.
C
210 mm
8.27 in
D
188 mm
7.4 in.
Frequency response
HERTZ Spl Show 12" 2000W 2 Ohm Dvc Subwoofer (Ss...
$744.99
SS 12 D2 subwoofer featuring 30 cm (12 in.) cone is eager to thrill the enthusiasts with their power.The suspension system reinforced with progressive double-layer spiders keeps the performance constant over time, especially in the heavy use typical of Bass Wars events.Heat dissipation is essential for this type of use and has been maximized thanks to an accurate design. The use of a robust 75 mm (3 in.) dual winding (2 + 2 Ω) voice coil developed in 4-layer configuration on a support with venting holes allows the SS 12 D2 to manage the impressive 2000 W peak power! The basket has been designed for optimal thermal dissipation and high mechanical resistance.The non-pressed paper cone with the addition of cotton fiber is the ideal compromise between stiffness and lightness, essential for a high sensitivity value. Suspension and leadwires are oversized to withstand the very high excursions generated by the massive ferrite engine.Push connectors accept cables with cross-section up to 12 AWG, for a practical and safe connection, suitable for the high currents involved.
Size mm (in.)
300 (12)
Power Handling - Continuous W
1000
Power Handling - Peak W
2000
Impedance Ohm
2+2
Depth mm (in.)
184 (7.24)
Voice Coil Type
dual
No Filter Component
SPL DUAL COIL SUBWOOFER
Voice Coil Ø
75 (3)
Magnet size D x d x h mm (in.)
170 x 90 x 40 (6.69 x 3.54 x 1.57)
Weight of one component kg (lb.)
8,8 (19.4)
Magnet
Ferrite
Cone
Non pressed paper with cotton fibre
Xmech mm (in.)
20,7 (0.81)
D mm
253
Xmax mm
15,4
Re Ohm
0,96
Fs Hz
36
Le mH
0,9
Vas I
24,52
Mms g
282,8
Cms mm/N
0,07
BL T*m
9,37
Qts
0,64
Qes
0,70
Qms
7,0
Spl dB
86
A
320 mm
12.6 in.
B
283 mm
11.14 in
C
184 mm
7.24 in.
D
161 mm
6.34 in.
HERTZ Mille Pro 12" 1000W 4 Ohm Svc Shallow Subwoofer...
$734.99
MPS 300 S4 shallow subwoofer has been designed to achieve exceptional performance even when there is very little space available to install the subwoofer box.MPS 300 is optimized to work in ultra-compact sealed boxesstarting from only 22,7 Lt (0.8 Cf). A typical example is a subwoofer enclosure under the rear bench of pickup trucks, where the space - and the height - are limited.Mille PRO subwoofer has a depth/performance ratio never achieved before thanks to the impressive cone excursion capacity which is 20% higher than a traditional design.This exceptional target has been achieved thanks to the ingenious suspension group design featuring a dedicated support structure for the spider and coil. This solution has allowed the movement of the magnetic group inwards, reducing the depth and at the same time maximizing cone linear excursion.
Size mm (in.)
300 (12)
Power Handling - Continuous W
500
Power Handling - Peak W
1000
Impedance Ohm
4
Depth mm (in.)
88 (3.46)
Voice Coil Type
single
No Filter Component
Subwoofers
Voice Coil Ø
38 (1.5)
Frequency Response Hz
25 - 400
Magnet size D x d x h mm (in.)
156 x 60 x 36 (6.14 x 2.36 x 1.42)
Weight of one component kg (lb.)
6,64 (14.64)
Magnet
High density flux ferrite
Cone
Polypropylene
Xmech mm (in.)
20 (0.79)
D mm
262,59
Xmax mm
16,80
Re Ohm
3,4
Fs Hz
23
Le mH
3,75
Vas I
62,13
Mms g
320
Cms mm/N
0,15
BL T*m
18,7
Qts
0,42
Qes
0,45
Qms
6,3
Spl dB
85
A
318,3
12.53
B
282,5
11.12
C
108,88
4.29
D
88
3.46
E
291,8
11.49
F
42,6
1.68
HERTZ Mille Pro 12" 1000W 2 Ohm Svc Shallow Subwoofer...
$734.99
MPS 300 S2 shallow subwoofer has been designed to achieve exceptional performance even when there is very little space available to install the subwoofer box.MPS 300 S2 is optimized to work in ultra-compact sealed boxesstarting from only 22,7 Lt (0.8 Cf). A typical example is a subwoofer enclosure under the rear bench of pickup trucks, where the space - and the height - are limited.MPS 300 S2 has a depth/performance ratio never achieved before thanks to the impressive cone excursion capacity which is 20% higher than a traditional design.This exceptional target has been achieved thanks to the ingenious suspension group design featuring a dedicated support structure for the spider and coil. This solution has allowed the movement of the magnetic group inwards, reducing the depth and at the same time maximizing cone linear excursion.
Size mm (in.)
300 (12)
Power Handling - Continuous W
500
Power Handling - Peak W
1000
Impedance Ohm
2
Depth mm (in.)
88 (3.46)
Voice Coil Type
single
No Filter Component
Subwoofers
Voice Coil Ø
38 (1.5)
Frequency Response Hz
25 - 400
Magnet size D x d x h mm (in.)
156 x 60 x 36 (6.14 x 2.36 x 1.42)
Weight of one component kg (lb.)
6,64 (14.64)
Magnet
High density flux ferrite
Cone
Polypropylene
Xmech mm (in.)
20 (0.79)
D mm
262,59
Xmax mm
16,80
Re Ohm
1,9
Fs Hz
24
Le mH
1,48
Vas I
64,9
Mms g
295
Cms mm/N
0,16
BL T*m
12,3
Qts
0,51
Qes
0,55
Qms
7,5
Spl dB
84,5
A
318,3
12.53
B
282,5
11.12
C
108,88
4.29
D
88
3.46
E
291,8
11.49
F
42,6
1.68
HERTZ Mille Pro 10" 1000W 4 Ohm Svc Shallow Subwoofer...
$629.99
Mille PRO shallow subwoofers have been designed to achieve exceptional performance even when there is very little space available to install the subwoofer box.MPS 250 S4 is optimized to work in ultra-compact sealed boxesstarting from only 14 Lt (0.49 Cf). A typical example is a subwoofer enclosure under the rear bench of pickup trucks, where the space - and the height - are limited.Mille PRO subwoofer have a depth/performance ratio never achieved before thanks to the impressive cone excursion capacity which is 20% higher than a traditional design.This exceptional target has been achieved thanks to the ingenious suspension group design featuring a dedicated support structure for spider and coil. This solution has allowed to move the magnetic group inwards, reducing the depth and at the same time maximizing cone linear excursion.
Size mm (in.)
250 (10)
Power Handling - Continuous W
500
Power Handling - Peak W
1000
Impedance Ohm
4
Depth mm (in.)
82,6 (3.25)
Voice Coil Type
single
No Filter Component
Subwoofers
Voice Coil Ø
38 (1.5)
Frequency Response Hz
25 - 400
Magnet size D x d x h mm (in.)
134 x 55 x 36 (6.28 x 2.17 x 1.42)
Weight of one component kg (lb.)
5,11 (11.27)
Magnet
High density flux ferrite
Cone
Polypropylene
Xmech mm (in.)
20 (0.79)
D mm
216,6
Xmax mm
16,8
Re Ohm
3,3
Fs Hz
29
Le mH
3,65
Vas I
21,2
Mms g
234
Cms mm/N
0,11
BL T*m
17,3
Qts
0,48
Qes
0,52
Qms
5,6
Spl dB
83,5
A
274,5
10.81
B
231,6
9.12
C
103,2
4.06
D
82,6
3.25
E
244,6
9.63
F
38,9
1.53
HERTZ Mille Pro 10" 1000W 2 Ohm Svc Shallow Subwoofer...
$629.99
Hertz MPS 250 S2 shallow subwoofer has been designed to achieve exceptional performance even when there is very little space available to install the subwoofer box.MPS 250 is optimized to work in ultra-compact sealed boxesstarting from only 14 Lt (0.49 Cf). A typical example is a subwoofer enclosure under the rear bench of pickup trucks, where the space - and the height - are limited.Mille PRO shallow subwoofer have a depth/performance ratio never achieved before thanks to the impressive cone excursion capacity which is 20% higher than a traditional design.This exceptional target has been achieved thanks to the ingenious suspension group design featuring a dedicated support structure for spider and coil. This solution has allowed to move the magnetic group inwards, reducing the depth and at the same time maximizing cone linear excursion.
HERTZ Mille Pro 12" 1200W 4 Ohm Dvc Subwoofer (Mp...
$609.99
Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line. The MP 300 D4.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound. The 65-mm 4-layer voice coil is higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 4 Ω + 4 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm).
Size mm (in.)
300 (12)
Power Handling - Continuous W
600
Power Handling - Peak W
1200
Impedance Ohm
4+4
No Filter Component
Subwoofers
Voice Coil Ø
65 (2,5)
Magnet size D x d x h mm (in.)
165 x 75 x 35 (6.5 x 2.95 x 1.38)
Weight of one component kg (lb.)
8,63 (19.03)
Magnet
High density flux ferrite
Cone
Water-repellent pressed paper
Xmech mm (in.)
±27 (1.06)
D mm
260
Xmax mm
17
Re Ohm
1,9
Fs Hz
24
Le mH
1,6
Vas I
74
Mms g
235
Cms mm/N
0,19
BL T*m
12
Qts
0,42
Qes
0,45
Qms
5,9
Spl dB
86
A
321 mm
12.64 in.
B
287 mm
11.3 in.
C
187 mm
7.36 in.
D
164 mm
6.46 in.
E
327,5 mm
12.89 in.
F
59 mm
2.32 in.
HERTZ Mille Pro 12" 1200W 2 Ohm Dvc Subwoofer (Mp...
$609.99
Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line. The MP 300 D2.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound. The 65-mm 4-layer voice coil is higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 2 Ω + 2 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm).
Size mm (in.)
300 (12)
Power Handling - Continuous W
600
Power Handling - Peak W
1200
Impedance Ohm
2+2
No Filter Component
Subwoofers
Voice Coil Ø
65 (2,5)
Magnet size D x d x h mm (in.)
164,5 x 75 x 35 (6.48 x 2.95 x 1.38)
Weight of one component kg (lb.)
8,63 (19.03)
Magnet
High density flux ferrite
Cone
Pressed-pulp cone with mineral powders
Xmech mm (in.)
±26 (1.02)
D mm
260
Xmax mm
± 16,00
Re Ohm
1 (2 coils in PARALLEL)
Fs Hz
23
Le mH
0,63
Vas I
88
Mms g
221
Cms mm/N
0,22
BL T*m
7,7
Qts
0,48
Qes
0,53
Qms
5,9
Spl dB
86
A
321 mm
12.64 in.
B
284 mm
11.18 in.
C
187 mm
7.36 in.
D
164 mm
6.46 in.
E
327,5 mm
12,89 in.
F
59 mm
2.32 in.
HERTZ Mille Pro 10" 1200W Subwoofer (Mp 250 D4.3 Pro)
$554.99
Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line. The MP 250 D4.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound. The 65-mm 4-layer voice coilis higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 4 Ω + 4 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm).
Size mm (in.)
250 (10)
Power Handling - Continuous W
600
Power Handling - Peak W
1200
Impedance Ohm
4+4
No Filter Component
Subwoofers
Voice Coil Ø
65 (2.5)
Magnet size D x d x h mm (in.)
156 x 80 x 35 (6.14 x 3.15 x 1.38)
Weight of one component kg (lb.)
7.8 (17,2)
Magnet
High density flux ferrite
Cone
Pressed-pulp cone with mineral powders
Xmech mm (in.)
±27 (1.06)
D mm
213
Xmax mm
17,00
Re Ohm
1,8
Fs Hz
27,00
Le mH
1,60
Vas I
31
Mms g
187,00
Cms mm/N
0,18
BL T*m
10,5
Qts
0,5
Qes
0,53
Qms
5,8
Spl dB
83,5
A
268 mm
10.55 in.
B
236 mm
9.29 in.
C
160 mm
6.3 in.
D
141 mm
5.55 in.
E
274 mm
10.79 in.
F
58,5 mm
2.3 in.
HERTZ Mille Pro 10" 1200W Subwoofer (Mp 250 D2.3 Pro)
$554.99
Outstanding performance in a compact size, this is the target of Mille Pro car audio subwoofers. On the strength of its know-how acquired with Mille Legend, the R&D team has optimized the production process to offer the “Hertz Sound Experience” to a wider audience using part of the technologies and materials of the flagship line. The MP 250 D2.3 cone is made by pressing paper pulp with the injection of mineral powders, the same construction technique used for Legend. The V-cone® profile increases rigidity, allowing the cone to function like a piston. Surround materials consist of high-purity IIR-butyl rubber. Like the Legend ML2000.3 and ML2500.3, the Mille PRO subwoofers are built with Boundary Free Surround technology allowing for a greater emission surface with equal diameter, generating higher sound pressure. The compact 6-spoke aluminum alloy anti-resonant basket is the same as the top model ML 2500.3 and contributes to the subwoofer’s mechanical damping, being absolutely transparent to the sound. The 65-mm 4-layer voice coilis higher than 60 mm and wound in a TIL-P former, thus delivering high linear displacement. The 2 Ω + 2 Ω DVC impedance configuration improves versatility to match any amplifier system. The air cooling and decompression system avoids the need for a centre hole on the bottom plate with three advantages:- Better thermal inertia to ensure low operating temperatures during musical transients;- Maximization of the magnetic field induced to the coil with the same overall motor dimensions. Thanks to a greater amount of iron in the pole the likelihood of magnetic saturation decreases exploiting the maximum flux density generated from the magnet;- Possibility to install the subwoofer right on the box wall, taking full advantage of its minimal dimensions. A damping rubber disk, provided with the product, secures the subwoofer to the box and ensures air exchange for the 10 vents on the bottom.The holes behind the voice coil winding and the 10 vents on the bottom plate ensure greater air exchange to the coil inner layers and work in synergy with an innovative assembly system. It forces the air to pass through the air gap to keep the coil operating temperature low, even with the most extreme musical programs. The terminal uses solid push connectors with an antishort circuit cover accepting cables up to 8 AWG to provide ultra-low wiring resistance in low impedance configurations (1ohm).
HERTZ Mille Legend 10" 1400W 4 Ohm Svc Subwoofer (Ml...
$1,154.99
Music fans who attend live concerts know well the emotions that low undistorted frequencies without dynamic compression can arouse. For this reason, the HertzAudioVideo R&D created ML 2500.3 Legend car audio subwoofer. During the long development phase, the designers set themselves just one ambitious goal: to transfer the emotions of a live performance to the car environment. Thanks to a completely renewed design, ML2500.3 car audio subwoofers have extremely compact size and are optimized to play in enclosures with reduced boxes. This choice of design combines two requirements hard to achieve up to now: reference performance and ease of installation.
Size mm (in.)
250 (10)
Power Handling - Continuous W
700
Power Handling - Peak W
1400
Impedance Ohm
4
No Filter Component
Subwoofers
Voice Coil Ø
100 (4)
Frequency Response Hz
27 ÷ 500
Magnet size D x d x h mm (in.)
95 x 28 x 6 D x d x h (in.) (3.7 x 1.1 x 0.24)
Weight of one component kg (lb.)
7,5 (16.53)
Magnet
Neodymium
Cone
Pressed-pulp cone with mineral powders
Xmech mm (in.)
±27 (1.06)
D mm
212,5
Xmax mm
17
Re Ohm
2,75
Fs Hz
33
Le mH
1,05
Vas I
23,5
Mms g
175
Cms mm/N
0,125
BL T*m
12,6
Qts
0,63
Qes
0,65
Qms
7,5
Spl dB
88
A
268 mm
10.55 in.
B
234 mm
9.21 in.
C
159 mm
6.26 in.
D
137 mm
5.4 in.
E
274 mm
10.78 in.
F
50 mm
1.97 in.
HERTZ Mille Legend 8" 1400W 4 Ohm Svc Subwoofer (Ml...
$1,049.99
Music fans who attend live concerts know well the emotions that low undistorted frequencies without dynamic compression can arouse. For this reason, the HertzAudioVideo R&D created ML 2000.3 Legend car audio subwoofer. During the long development phase of this car audio speakers, the designers set themselves just one ambitious goal: to transfer the emotions of a live performance to the car environment. Thanks to a completely renewed design, ML2000.3 car audio subwoofers have extremely compact size and are optimized to play in enclosures with reduced boxes. This choice of design combines two requirements hard to achieve up to now: reference performance and ease of installation.
Size mm (in.)
200 (8)
Power Handling - Continuous W
700
Power Handling - Peak W
1400
Impedance Ohm
4
Voice Coil Type
single
No Filter Component
Subwoofers
Voice Coil Ø
100 (4)
Frequency Response Hz
30 ÷ 600
Magnet size D x d x h mm (in.)
95 x 28 x 5 (3.7 x 1.1 x 0.2)
Weight of one component kg (lb.)
6,120 (13.5)
Magnet
Neodymium
Cone
Pressed-pulp cone with mineral powders
Xmech mm (in.)
±23 (0.9)
D mm
165
Xmax mm
13
Re Ohm
2,7
Fs Hz
40
Le mH
0,72
Vas I
9,5
Mms g
110
Cms mm/N
0,15
BL T*m
11
Qts
0,56
Qes
0,63
Qms
5
Spl dB
86
A
217 mm
8.54 in.
B
185 mm
7.28 in.
C
138 mm
5.43 in.
D
117 mm
4.6 in.
E
223 mm
8.78 in.
F
46 mm
1.8 in.
HERTZ Mille Legend 7" Woofer Component - Pair (Ml 1800.3...
$994.99
ML 1800.3 Legend car audio woofers has been thought and designed for the enthusiasts attending contests who need a component merging the timbre accuracy of ML 1650.3 Legend to a wider extension to the low frequencies thanks to the large emission surface, higher power handling and control which only a 50 mm voice coil can ensure. To get to these results, the R&D staff performed extensive in-car voicing sessions, after building several prototypes with the FEA simulation method and testing them with a wide array of measurements carried out with the Klippel® suite. Like in the suspensions of competition cars, the surround must stand the most extreme working conditions to ensure maximum stability and symmetry at high excursions, and so to achieve impact and extension to the low frequency range. For this reason, the electro-acoustic designers developed a new surround-basket gluing system called “Boundary Free Surround”. This technology, provides the ability to achieve wider emission surface of the cone compared to speakers with same diameter; that way, the cone manages to move a bigger mass of air, so it produces more acoustic pressure.
Component
Woofer
Size mm (in.)
180 (7)
Power Handling - Continuous W
200
Power Handling - Peak W
400
Impedance Ohm
4
Voice Coil Ø
50 (2)
Frequency Response Hz
38 - 6k
Magnet size D x d x h mm (in.)
90 x 60,7 x 5 (3.54 x 2.39 x 0.2)
Weight of one speaker kg (lb.)
1,71 (3.77)
Magnet
Neodymium
Cone
Pressed-pulp cone with cotton fibres
Xmech mm (in.)
±10 (0.4)
D mm
149
Re Ohm
3,2
Fs Hz
60
Le mH
0,35
Vas I
12,2
Mms g
27,5
Cms mm/N
0,3
BL T*m
7,8
Qts
0,5
Qes
0,53
Qms
7,22
Spl dB
93
A
184 mm
7.24 in.
B
160 mm
6.3 in.
C
88 mm
3.46 in.
D
76 mm
3 in.
E
189,2 mm
7.45 in.
F
27 mm
1.06 in.
HERTZ Mille Legend 6.5" Woofer Component - Pair (Ml 1650.3...
$849.00
During these past few years the Mille line car audio woofers have been the choice of many enthusiasts looking for extreme performance; with ML 1650.3 Legend the Hertz designers increased again the limits of achievable performance for components designed for door installation. To get to these results, the R&D staff performed extensive in-car voicing sessions, after building several prototypes with the FEA simulation method and testing them with a wide array of measurements carried out with the Klippel® suite. To ensure extraordinary power handling and very high thermal stability even with tracks especially rich of bass frequencies, ML 1650.3 Legend features a 36 mm mobile voice coil. This size ensures the best compromise between power handling and high frequency response. The cone geometry has been subject of in-depth studies with FEA simulations and measurements performed with the Klippel Scan Vibrometer; all that led to the optimization of the V-cone® profile. In the subwoofers and in the woofers, to reproduce the lowest frequency spectrum, the cone needs to move a remarkable amount of air, so it is forced to make long excursions moving like a piston does. The V-cone® profile prevents the cone from deforming during its course, ensuring that the “piston” works in a correct position, maximizing the production of acoustic pressure.
Component
Woofer
Size mm (in.)
165 (6.5)
Power Handling - Continuous W
125
Power Handling - Peak W
250
Impedance Ohm
4
Voice Coil Ø
36 (1.4)
Frequency Response Hz
40 - 6.5k
Magnet size D x d x h mm (in.)
80 x 45 x 5 (3.15 x 1.77 x 0.2)
Weight of one speaker kg (lb.)
1,29 (2.84)
Magnet
Neodymium
Cone
Pressed-pulp cone with cotton fibres
Xmech mm (in.)
±9 (0.35)
D mm
132
Re Ohm
3,3
Fs Hz
65
Le mH
0,24
Vas I
8,3
Mms g
17,5
Cms mm/N
0,3
BL T*m
7
Qts
0,52
Qes
0,52
Qms
5,3
Spl dB
93
A
165 mm
6.5 in.
B
141 mm
5.55 in.
C
80 mm
3.15 in.
D
69 mm
2.71 in.
E
170 mm
6.7 in.
F
26 mm
1.02 in.
HERTZ Dieci 12" 1000W 4 Ohm Dvc Subwoofer (Ds 30.3)
$189.99
Hertz DS 30.3 car audio subwoofers box offers high efficiency and exceptional power handling. Equipped with a polypropylene membrane and butyl rubber surround, they provide high excursion with minimal distortion. An efficient cooling system ensures optimal heat dissipation, increasing their reliability.The Dieci subwoofers are designed for use in compact sealed or reflex enclosures; thanks to an exclusive, carefully thought-out design, they can be used in any installation.
Size mm (in.)
300 (12)
Power Handling - Continuous W
250
Power Handling - Peak W
1000
Impedance Ohm
4
Voice Coil Type
single
No Filter Component
Subwoofer
Voice Coil Ø
38 (1.5)
Frequency Response Hz
28 ÷ 300
Magnet size D x d x h mm (in.)
115 x 50 x 25 D x d x h (in.) (4.5 x 2 x 1)
Weight of one component kg (lb.)
4 (8.8)
Magnet
High density flux ferrite
Cone
Polypropylene with Mica injection
Xmech mm (in.)
9
D mm
258
Xmax mm
9
Re Ohm
3,3
Fs Hz
32
Le mH
2,2
Vas I
70
Mms g
133
Cms mm/N
0,18
BL T*m
11,2
Qts
0,62
Qes
0,71
Qms
5,14
Spl dB
91
A
306 mm
12 in.
B
279 mm
11 in.
C
132 mm
5.2 in.
D
120 mm
4.7 in.
HERTZ Dieci 10" 600W 4 Ohm Svc Subwoofer (Ds 25.3)
$154.99
Hertz DS 25.3 car audio subwoofers offer high efficiency and exceptional power handling. Equipped with a polypropylene membrane and butyl rubber surround, they provide high excursion with minimal distortion. An efficient cooling system ensures optimal heat dissipation, increasing their reliability.
Size mm (in.)
250 (10)
Power Handling - Continuous W
150
Power Handling - Peak W
600
Impedance Ohm
4
No Filter Component
Subwoofer
Voice Coil Ø
38 (1.5)
Frequency Response Hz
32 ÷ 400
Magnet size D x d x h mm (in.)
100 x 50 x 25 (4 x 2 x 1)
Weight of one component kg (lb.)
3 (6.6)
Magnet
High density flux ferrite
Cone
Polypropylene with Mica injection
Xmech mm (in.)
16 (0.63)
D mm
215
Xmax mm
9
Re Ohm
3,3
Fs Hz
36
Le mH
2,15
Vas I
34
Mms g
106
Cms mm/N
0,18
BL T*m
8,5
Qts
0,92
Qes
1,13
Qms
5
Spl dB
89
A
257 mm
10.2 in.
B
234 mm
9.2 in.
C
116 mm
4.6 in.
D
104 mm
4.1 in.
HERTZ Dieci 8" 440W Active Underseat Subwoofer (Dba 201 F)
$600.00
The DBA 201 F flat active subwoofer enclosure optimized with FEM simulation ensures superior performance, maximizing the subwoofer output with a super flat size. The massive magnet of the 8 in. driver provides optimal control during the highest cone excursion.Extra full set of controls to fine-tune the in-car performanceThe built-in 24 dB/Oct. low-pass crossover filter with a variable cutting corner frequency (50÷150 Hz) allows you to perfectly match the DBA 201 F to your speaker system. Adjustable bass boost (0÷6 dB @ 45Hz) can add bass output as you prefer, allowing correction for OEM sound equalization. With the phase inverter (0-180°), you can optimize phase alignment between the DBA 201 F and your speaker system, regardless of the subwoofer’s position in the car. The subsonic filter (15 Hz @ 24 dB/Oct) protects the cone from over-excursion and amplifiers from overheating. The input sensitivity control is the perfect tool to maximize the overall system output level while preventing clipping.Auto turn-on and standby modeThe built-in audio sense circuit allows the DBA 201 F to turn on and timeout to standby mode automatically. You can switch off the audio sense function when a remote turn-on wire is available.
Size mm (in.)
200 (8)
Power Handling - Continuous W
220
Power Handling - Peak W
440
Impedance Ohm
0.4
Design
Super Flat Sealed
Voice Coil Ø
38.6 (1.52) mm (in.)
Frequency Response Hz
32 ÷ 400
Magnet size D x d x h mm (in.)
110 x 45 x 17 (4.33 x 1.78 x 0.67)
Weight of one component kg (lb.)
4.3 (9.48)
Magnet
High Density Flux Ferrite
Cone
Pressed paper
Voice Coil Type
Copper
Operating voltage VDC (Fuse)
6.5 ÷ 18 (15A)
Start - Stop voltage VDC
6
Idling current A (Power OFF)
260 m (1 m)
Consumption @ 14,4 VDC Max musical power A
8.5
Remote IN Turn on VDC (Current)
4 (1 mA)
PRE input signal Turn ON VRMS
10 mV
SPK input DC Turn ON VDC
2
Distortion - THD @ 100 Hz %
0.15
Bandwidth Hz
15 - 150
S/N ratio dBA
100
Output power (RMS) @ 14,4 VDC, 1% THD W
220
PRE input signal VRMS (impedance)
0.2 ÷ 5 (10kΩ)
SPK input signal VRMS (impedance)
1.2 ÷ 30 (6Ω)
LO-PASS Filter @ 24 dB Oct adjustable Hz
50 ÷ 150
Subsonic Filter @ 24 dB Oct Fixed Hz
15
Phase switch
0 / 180°
Bass Boost @45 Hz dB
0 ÷ 6
Sub remote volume control dB
0 ÷ -15 (HRC 01 included)
mm
in
A
345
13.58
B
245
9.64
C
79
3.11
LIGHTFORCE BEAST 230 Super Bundle — Driving Lights (pair) and...
$1,129.00
$1,352.00
LIGHTFORCE BEAST 230 3-Mode Driving Light Ultimate Bundle
Upgrade your vehicle lighting with the complete LIGHTFORCE BEAST 230 Ultimate Bundle. Designed for off-road enthusiasts, touring vehicles, and professional applications, this all-in-one kit delivers maximum visibility, durability, and ease of installation.
This bundle includes a pair of powerful BEAST 230 LED driving lights and a dedicated plug-and-play wiring harness for a complete lighting upgrade.
What’s Included
LIGHTFORCE BEAST 230 LED Driving Light - Pair (3-Mode) – BEAST230PK
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play solution with no additional parts required
3 beam modes: Spot, Flood, and BEAST for versatile driving conditions
Extended beam distance and wider spread for maximum visibility
Heavy-duty construction designed for extreme environments
Quick and easy installation with included wiring harness
BEAST 230 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
High-output LED performance for long-range and wide visibility
Optimised beam pattern for off-road and highway use
5700K colour temperature for clear, natural visibility
Large format design for increased light output and coverage
Daytime Running Light (DRL) functionality
Heavy-duty aluminium housing for durability and heat management
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Single 8-pin connector for clean installation
Includes relay, rocker switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
Impact-resistant construction for harsh environments
Operating temperature range: -40°C to 85°C
Resistant to UV, salt spray, and corrosion
Long-lasting LED lifespan
Specifications
Light Size: 230mm
Voltage: 12V system compatible
Colour Temperature: 5700K
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Rural and low-light environments
Why Choose LIGHTFORCE BEAST 230 Bundle
This bundle provides a complete, professional-grade lighting solution with industry-leading performance and durability. With advanced beam technology and simple installation, it is the ideal upgrade for drivers who demand reliability and visibility.
Order now to upgrade your driving visibility with a complete BEAST lighting setup.
LIGHTFORCE BEAST 190 Ultimate Bundle — Pair of Driving Lights...
$999.00
$1,150.00
LIGHTFORCE BEAST 190 Ultimate Bundle – 3-Mode Pair Of Driving Lights with Wiring Harness
The LIGHTFORCE BEAST 190 Ultimate Bundle is a complete high-performance lighting solution designed for off-road, touring, and demanding driving conditions. This bundle combines the powerful BEAST 190 LED driving lights with a dedicated 3-mode wiring harness for a simple, professional installation.
Engineered and manufactured in Australia, the BEAST 190 delivers exceptional beam distance, width, and durability in a compact 190mm design. With three selectable beam modes, this system allows you to adapt instantly to changing environments for maximum control and confidence.
What’s Included
2 X LIGHTFORCE BEAST 190 LED Driving Light – BEAST190X1
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play lighting solution
3 beam modes: Spot, Flood, and BEAST
Up to 1260m beam distance for long-range visibility
Compact design with extreme durability
Quick and easy installation with dedicated wiring harness
BEAST 190 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
Up to 1 lux at 1260m (pair) for long-distance performance
25 high-performance Osram LEDs
5700K colour temperature for clear, natural visibility
Compact 190mm size with ultra-slim 80mm depth
Daytime Running Light (DRL) functionality
Pressure die-cast aluminium housing for strength and heat dissipation
Beam Modes
Spot Mode: Long-distance beam up to 1195m
Flood Mode: Wide beam up to 496m
BEAST Mode: Combined distance and width up to 1260m
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Includes relay, switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
IK16 impact resistance for extreme durability
Operating temperature range from -40°C to 85°C
Resistant to UV, salt spray, and corrosion
LED lifespan up to 50,000 hours
Specifications
Diameter: 190mm
Depth: 80mm
Weight: 1.6kg
Voltage: 13.2V
Ingress Rating: IP69K
Colour Temperature: 5700K
Warranty: 5 Years
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Low-light and rural environments
Why Choose This Bundle
This bundle delivers a complete, professional-grade lighting upgrade with everything required for installation. Combining advanced LED performance, versatile beam control, and enhanced durability, it is ideal for drivers who demand reliability and maximum visibility in all conditions.
Upgrade your setup with the LIGHTFORCE BEAST 190 Ultimate Bundle today.
ALPINE LC70 Ultimate Status Audio & Camera Bundle, Speakers +...
$6,899.00
$7,700.00
ALPINE LC70 Ultimate Status Audio and Camera Bundle – Complete Premium Sound System
The ALPINE LC70 Ultimate Status Bundle is the complete high-end audio and safety upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining Alpine’s advanced i905-LC70 head unit, R2-Series speaker system, Alpine Status HDA-V90 amplifier, RS-SB10 shallow subwoofer, and rear view camera, this bundle delivers exceptional sound quality, powerful bass, and enhanced driving visibility.
Built using Alpine’s latest Hi-Res Audio technology, this system delivers a true high-resolution listening experience with precision, clarity, and depth, while maintaining seamless factory-style integration.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE HDA-V90 5-Channel Hi-Res Audio Amplifier
ALPINE RS-SB10 Shallow Subwoofer Enclosure
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete premium audio and safety system in one bundle
Hi-Res Audio performance with powerful, detailed sound
Deep, controlled bass from shallow subwoofer design
High-output 5-channel amplifier for full system control
Wireless Apple CarPlay and Android Auto connectivity
Improved reversing safety with rear view camera
Seamless integration for LandCruiser 70 Series Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier and advanced sound tuning
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for accurate sound reproduction
Glass-fibre reinforced cones for clarity and response
HAMR surround for enhanced bass performance
Integrated door pods with USB charging and storage
HDA-V90 Amplifier Features
5-channel Class-D amplifier with Hi-Res Audio certification
Frequency response: 10Hz – 60kHz
75W x 4 + 300W x 1 @ 4Ω output
100W x 4 + 500W x 1 @ 2Ω output
High damping factor for precise speaker control
Low distortion for clean and accurate sound
RS-SB10 Subwoofer Features
Shallow 12-inch high-performance subwoofer enclosure
600W RMS and 1800W peak power handling
Ultra-compact design for flexible installation
Neodymium magnet for high efficiency and power
20mm X-max for deep, controlled bass output
Rear View Camera Features
Wide viewing angle for improved rear visibility
HDR technology for clear image in low light conditions
Automatic activation when reversing
Day and night image adjustment
System Performance
High-resolution audio playback across full system
Powerful amplified output with deep bass response
Balanced sound staging with precise tuning capability
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete premium audio system
Off-road and touring vehicles
Users wanting high-performance sound and added safety
Why Choose This Bundle
This bundle represents the ultimate Alpine upgrade, combining industry-leading components into one complete system. Designed for performance, clarity, and reliability, it delivers a superior in-car experience with powerful sound, deep bass, and enhanced safety features.
Transform your LandCruiser 70 Series with Alpine’s ultimate audio and camera system.
ALPINE LC70 Premium Audio Bundle — Head Unit + Speakers
$4,499.00
$5,199.90
ALPINE LC70 Premium Audio Bundle – i905-LC70 Head Unit with R2-Series Speaker Upgrade
The ALPINE LC70 Premium Audio Bundle is the ultimate in-car sound upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 9-inch multimedia receiver with Alpine’s R2-Series door pod speaker system, this bundle delivers powerful, high-resolution audio with seamless factory-style integration.
Designed for both performance and practicality, this setup transforms your vehicle into a premium listening environment while enhancing interior functionality and aesthetics.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
Key Benefits
Complete premium audio upgrade for LandCruiser 70 Series Dual Cab
High-resolution sound with powerful bass and clarity
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration with modern design enhancement
Additional functionality with storage, USB charging, and lighting
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
Seamless integration designed for LC70 interior
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear for powerful output
Hi-Res Audio certified for accurate and detailed sound
Glass-fibre reinforced cones for fast response and clarity
HAMR surround for increased bass performance and control
Neodymium magnet structure for improved efficiency
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated front and rear speaker pods
Built-in USB charging ports (up to 4 devices)
Integrated puddle lighting for improved visibility at night
Storage compartments for bottles, maps, and accessories
Durable injection-moulded PC/ABS construction
Performance Specifications
Peak Power Handling: 300W
RMS Power Handling: 100W
Nominal Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Woofer Size: 6x9 inch
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers upgrading factory audio systems
Off-road and touring vehicles
Users seeking premium sound quality and modern connectivity
Why Choose This Bundle
This bundle delivers a complete, high-performance audio upgrade with seamless integration, powerful sound output, and added interior functionality. Designed specifically for the LC70, it combines Alpine’s industry-leading technology with practical features for everyday use and off-road adventures.
Upgrade your LandCruiser 70 Series with Alpine’s premium audio solution today.
ALPINE LC70 Ultimate Audio System Bundle — Head Unit +...
$5,099.00
$5,899.85
ALPINE LC70 Ultimate Audio System Bundle – Head Unit, Speaker Upgrade and Amplifier
The ALPINE LC70 Ultimate Audio System Bundle is a complete premium sound upgrade designed specifically for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 multimedia receiver, Alpine R2-Series speaker door pod system, and the powerful R2-A60F amplifier, this bundle delivers exceptional clarity, depth, and power.
Engineered for audiophiles and off-road enthusiasts, this system transforms your vehicle into a high-performance listening environment with seamless factory-style integration and modern connectivity.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE R2-A60F Class-D Digital Amplifier
Key Benefits
Complete premium audio system upgrade in one bundle
High-resolution sound with powerful bass and clarity
Amplified performance for maximum output and control
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration designed for LC70 Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for detailed and accurate sound
Glass-fibre reinforced cones for fast response
HAMR surround for increased bass performance
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated speaker pods front and rear
Built-in USB charging ports for up to 4 devices
Integrated puddle lighting for improved visibility
Storage compartments for everyday convenience
Durable PC/ABS construction for long-lasting use
R2-A60F Amplifier Features
Compact Class-D digital amplifier with reduced footprint
Hi-Res Audio certified up to 45kHz
Top panel sound controls for easy tuning
One-sided terminal layout for simplified installation
100W RMS x 4 @ 4Ω output
150W RMS x 2 @ 2Ω output
300W RMS x 2 @ 4Ω bridged
Frequency response: 10Hz – 45,000Hz
High damping factor for improved speaker control
Performance Specifications
Speaker Peak Power: 300W
Speaker RMS Power: 100W
Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete audio system upgrade
Off-road and touring vehicles
Users wanting powerful, high-quality sound performance
Why Choose This Bundle
This bundle delivers a complete, high-performance audio solution combining premium components for superior sound quality, power, and control. Designed specifically for the LC70, it ensures seamless integration while providing a significant upgrade over factory audio systems.
Upgrade your LandCruiser 70 Series with Alpine’s ultimate audio system bundle today.
ALPINE LC70 Premium Head Unit & Reverse Camera Bundle —...
$2,699.00
$3,099.90
ALPINE LC70 Premium Head Unit and Reverse Camera Bundle – i905-LC70 with HCE-C1100 Camera
The ALPINE LC70 Premium Bundle combines cutting-edge infotainment with enhanced driving safety, designed specifically for Toyota LandCruiser 70 Series. Featuring the advanced i905-LC70 9-inch multimedia receiver and the HCE-C1100 rear view camera, this bundle delivers seamless connectivity, high-resolution audio, and improved visibility when reversing.
Upgrade your dashboard with a modern, integrated system that enhances both your driving experience and vehicle functionality.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete infotainment and safety upgrade in one bundle
Wireless Apple CarPlay and Android Auto connectivity
High-definition 9-inch WXGA display
Enhanced reversing visibility with wide-angle camera
Seamless integration designed for LandCruiser 70 Series
i905-LC70 Head Unit Features
9-inch WXGA high-resolution display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for superior sound performance
Advanced sound tuning for custom audio control
Seamless integration with LandCruiser 70 Series interior
Rear View Camera Features
Wide viewing angle: 131° horizontal, 103° vertical
HDR technology for clear vision in low-light conditions
Automatic day and night image adjustment
RCA or direct Alpine connection compatibility
Automatic activation when reversing
Compact design with included mounting hardware
Camera Specifications
Resolution: 640 x 480
Waterproof rating: IP67
Power supply: DC5.0V – DC7.0V
Viewing angle: 131° horizontal, 103° vertical
Operating temperature: -30°C to +70°C
Designed For
Toyota LandCruiser 70 Series
Off-road and touring vehicles
Daily driving and work vehicles
Drivers seeking upgraded audio and safety
Why Choose This Bundle
This bundle delivers a complete in-car upgrade, combining premium audio performance with enhanced safety features. Designed specifically for the LandCruiser 70 Series, it ensures seamless integration, modern functionality, and improved driving confidence.
Upgrade your LandCruiser 70 Series with Alpine’s premium multimedia and camera solution today.
