ALPINE Digital Mono Power Amplifier - S2-A60M
$422.96
$469.95
The next generation of Alpine S-Series amplifiers are designed to take your car audio experience to the next level without breaking the bank. With a sleek new redesign and upgraded features from their predecessors, these amplifiers offer exceptional performance and power on an affordable budget.
The next generation S-Series S2-A60M mono subwoofer amplifier makes it a lot easier to get great bass in your vehicle, delivering up to 600 Watts RMS power @ 2 Ohms. A variable bass boost allows you to dial in some extra punch and impact for more low-frequency enjoyment. You can even add an optional wired remote to control the level of bass from your front seat.
A built-in low-pass filter puts you in command of the frequency spectrum that reaches your sub. The amp includes pre-amp- and speaker-level inputs, so you can install it in almost any vehicle, even one with a factory radio. When using the speaker-level inputs, the amp can sense the incoming signal and turn itself on, eliminating the need to run a separate turn-on wire to the receiver or fuse box.
S-Series amplifiers are available in two mono, a 4-channel and a 5-channel configuration.
ALPINE R-Series 12 Dual 4 Ohm Dvc Subwoofer - R2-W12D4
$494.96
$549.95
Next-Generation 12-inch (30cm) R-Series Subwoofer with Dual 4-Ohm Voice Coils
The new 2022 R-Series subwoofers are here - drawing from decades of Subwoofer engineering experience. They deliver deep, clean, accurate bass and feature Alpine’s HAMR Surround for maximum cone excursion, delivering tons of bass output. the new ceramic dust cap is very light weight and rigid, keeping distortion an absolute minimum. The new, enlarged motor structure ensures better overall woofer control for a clean, strong bass response.
General
Sealed: 12″
Frequency Response: 24Hz-200kHz
RMS Power Handling: 750W
Peak Power Handling: 2250W
FRONT RUNNER Land Rover Discovery Lr4 Battery Bracket- - BBLD004
$202.50
$225.00
This battery bracket allows you to fit an additional battery to your vehicle by mounting as an additional bracket under your vehicle's hood.
Includes all fitment parts.
Made out of black powder coated high strength steel.
Fits Right Hand Drive vehicles.
NOTE: Not suitable for models fitted with an Auxiliary heater.
FRONT RUNNER Cargo Slide/Fridge Slide / 80L To 90L- -...
$395.10
$439.00
Front Runner Fridge Slide 80L–90L
The Front Runner Fridge Slide 80L–90L is a heavy-duty storage solution designed to provide convenient access to portable fridges, camping equipment, storage boxes, and touring gear. Ideal for 4WDs, canopies, caravans, ute trays, and drawer systems, this low-profile slide maximises accessibility while minimising the space required within your vehicle.
Featuring high-strength bearing drawer slides, the tray extends nearly 100% from its anchored base, making it easy to access your fridge and equipment without climbing into the vehicle. The rattle-free design and secure swivel latch locking mechanism help keep your cargo stable and secure during travel.
Constructed from durable black powder-coated steel and supplied with mounting hardware for wood and metal surfaces, this fridge slide is built to withstand demanding touring, camping, overlanding, and worksite conditions.
Features
Suitable for 80L–90L portable fridges
Heavy-duty 100kg load capacity
High-strength bearing drawer slide system
Nearly 100% tray extension for easy access
Low-profile design maximises storage space
Rattle-free operation during travel
Secure swivel latch locking system
Mounts to most flat surfaces
Compatible with Front Runner drawer systems
Pre-drilled mounting holes for easy installation
Includes mounting hardware for wood and metal surfaces
Durable black powder-coated steel construction
Specifications
Overall / Closed Dimensions: 920mm x 580mm x 65mm
Open Dimensions: 1830mm x 580mm x 65mm
Internal Dimensions: 880mm x 508mm x 25mm
Weight: 16.7kg
Maximum Load Capacity: 100kg
Material: 1.8mm Black Powder-Coated Steel
What's Included
1 x Front Runner Fridge Slide
1 x L-Bracket Latch
Bolt Kit
Frequently Asked Questions
What fridge sizes are suitable for this Front Runner Fridge Slide?
This slide is designed to suit many popular portable fridges in the 80L–90L range. Always compare your fridge dimensions with the tray measurements before purchasing.
Can this fridge slide be mounted in a canopy, caravan, or ute tray?
Yes. The slide can be mounted to most suitable flat surfaces, including canopies, caravans, ute trays, drawer systems, and touring vehicle storage setups.
Does the slide lock securely during travel?
Yes. The integrated swivel latch locking system and rattle-free design help keep your fridge and equipment secure while travelling on-road and off-road.
Note: Fridges and storage containers shown are sold separately.
FRONT RUNNER Gas/Propane Bottle Holder- - GBHO012
$264.60
$294.00
Fuel your adventure with this easy-to-use gas/propane holder that attaches securely to any Front Runner Rack Tray. Never be far from the comforts of your portable stove and other propane accessories again. The simple latching method allows you to quickly attach different sized bottles.
Perfect for portable cooking stoves, geyser/water heaters, heaters and lamps.
Rack brackets securely hold your gas/propane bottle on your rack.
2 latches feature a safety catch to prevent any movement and are lockable with a for added safety.
The removable collar is placed over the cylinder valve collar and latched on the rack brackets.
The collar rods are adjustable to suit various bottle heights.
Max Cylinder Height: 320mm (12.6")Max Cylinder Diameter: 280mm (11")Max Top Collar Diameter: 175mm (6.9")Max Weight: 10kg (22lbs)
Consists of:1 x Pair of Rack Brackets1 x LPG Cylinder BracketInstallation HardwareFitting InstructionMaterials used:Black powder coated steelStainless steel safety latchesSpecial Notes:Cylinder dimension guidelines:Max Cylinder Height: 12.6" (320mm)Max Cylinder Diameter: 11" (280mm)Max Top Collar Diameter: 6.7" (170mm)Max Weight: 22lb (10kg)
FRONT RUNNER Land Rover Defender 90/110 Single Gas Bottle Bracket-...
$326.70
$363.00
Transport and store you Gas/Propane bottle onto your Land Rover 90 & 110 with this high strength steel, gutter mount Single Gas Bottle Bracket.
The bracket secures a single gas / propane bottle to the Land Rover Defender 90 & 110.
For installation, drilling is required.
This holder features a black powder coated high strength steel bracket and adjustable clamp to accommodate gas bottles with a diameter of 210mm (8.3") up to 290mm (11.4").
The bracket is lockable with the Rack Accessory Lock / Small.
Supplied with installation hardware.
Consists of:1 x Gas Bottle Frame1 x Gas Bottle Base Plate1 x Adjustable Gas Bottle ClampInstallation HardwareFitting Instruction
Materials used:Black powder coated high strength steel
Assembled Product Dimensions:341mm (13.4") L x 294mm (11.5") W x 621mm (24.4") H
Weight:5.4kg (11.9lbs)Suitability:Holds gas bottles ranging from 210mm (8.3") to 290mm(") in diameter
FRONT RUNNER Land Rover Defender Puma (2007-2016) Gullwing Box Shelf-...
$215.10
$239.00
Shelf made from plywood and powder-coated mild steel.Up to 6 of these shelves can be used in a gullwing box.Shelf has slots cut in to allow for various fixing straps or elastic straps to be used to secure plates or other items.
Consists of:1x Mild steel & wood Shelf1x Installation KitMaterial used:Shelf: Stained PlywoodShelf Support: Black powder-coated mild steelProduct dimensions:264mm (10.4") L x 856mm (33.7") W x 36mm (1.4") HWeight:3.8kg (8.4lbs)
FRONT RUNNER Land Rover Defender Puma (2007-2016) Gullwing Box- -...
$499.50
$555.00
The Front Runner Gullwing Box is used in conjunction with the Front Runner Gullwing Window-Glass or Front Runner Gullwing Window-Aluminium. This creates extra convenient storage space for your Land Rover Defender Puma. Front Runner Gullwing Box Shelves can be used to create divisions in the box for storage. *Front Runner Gullwing Box Shelves, sold seperately.
Consists of:1x Fastening Kit2x Pinch Welds2x Side Panels - 1 Left, 1 Right2x Mounting Brackets1x Top Panel2x Wooden Back Board1x Bottom PanelMaterials used:Black powder coated steelBack Board: Stained PlywoodProduct dimensions:860mm (33.9") W x 310mm (12.2") L x 654mm (25.8") H (Box)860mm (33.9") W x 310mm (12.2") L x 746mm (29.4") H (Overall incl. Brackets)Weight:13.1kg (28.9lbs)
FRONT RUNNER Toyota Land Cruiser 76 Gullwing Window / Left...
$1,377.90
$1,531.00
The Front Runner Glass Gullwing Window replaces the stock LEFT HAND rear window with an upward/outward opening window that is hinged at the top. Create easy access to the rear storage area of your Toyota Land Cruiser 76.
The Front Runner Gullwing window replaces the rear window of a Toyota Land Cruiser 76 allowing easy access to the cargo bay via the side of the vehicle.While built for off-road durability and ease of use, the Front Runner Glass Gullwing Window looks smart and was designed to blend seamlessly with the exterior stylings of the vehicle.
Includes 2 locking latches.
The Toyota Land Cruiser 76 can be brought back to stock within minutes by removing and replacing with standard window.
Drilling required for fitment.
Consists of:Steel FrameHingesGas strutsLocksSet of keysGlass PanelMaterials used:Black powder-coated high strength steelTinted and toughened 6mm glassProduct Dimensions:886mm (34.9") W x 537mm (21.1") H x 53mm (2.1") DWeight:14kg (30.9lbs)Glass specifications:Visible Light:Transmission: 44Reflection Outside: 5Solar Energy:Total Elimination: 38Reflection Outside: 5Absorption 1: 47Direct Transmission: 47SHGC: 0.62Shading Coefficient:Ratio: 0.71U Value:(W/m2).K (Center of Glass): 5.8
FRONT RUNNER Toyota Land Cruiser 76 Gullwing Window / Right...
$1,377.90
$1,531.00
The Front Runner Glass Gullwing Window replaces the stock RIGHT HAND rear window with an upward/outward opening window that is hinged at the top. Create easy access to the rear storage area of your Toyota Land Cruiser 76.
The Front Runner Gullwing window replaces the rear window of a Toyota Land Cruiser 76 allowing easy access to the cargo bay via the side of the vehicle.While built for off-road durability and ease of use, the Front Runner Glass Gullwing Window looks smart and was designed to blend seamlessly with the exterior stylings of the vehicle.
Includes 2 locking latches.
The Toyota Land Cruiser 76 can be brought back to stock within minutes by removing and replacing with standard window.
Drilling required for fitment.
Consists of:Steel FrameHingesGas strutsLocksSet of keysGlass PanelMaterials used:Black powder-coated high strength steelTinted and toughened 6mm glassProduct Dimensions:886mm (34.9") W x 537mm (21.1") H x 53mm (2.1") DWeight:14kg (30.9lbs)Glass specifications:Visible Light:Transmission: 44Reflection Outside: 5Solar Energy:Total Elimination: 38Reflection Outside: 5Absorption 1: 47Direct Transmission: 47SHGC: 0.62Shading Coefficient:Ratio: 0.71U Value:
FRONT RUNNER Toyota Land Cruiser 76 Gullwing Window Panel /...
$341.10
$379.00
This Aluminium Gullwing Window Panel is sold as a seperate component in order to replace a damaged window.If you currently own a Glass Gullwing Window and would like to swap out your glass panel for an aluminium panel, the Gullwing Window's Panel has been designed to be interchangable. The aluminium panel allows for added security and blocks out view of your goods in the load bed area of your vehicle.
Consists of:1x Aluminium panelMaterials used:Black powder-coated AluminiumProduct Dimensions:705mm (27.8") W x 440mm (17.3") H x 6mm (0.2") DWeight:3.16kg (7lbs)
FRONT RUNNER Toyota Land Cruiser 76 Gullwing Window Panel /...
$341.10
$379.00
This Aluminium Gullwing Window Panel is sold as a seperate component in order to replace a damaged window. If you currently own a Glass Gullwing Window and would like to swap out your glass panel for an aluminium panel, the Gullwing Window's Panel has been designed to be interchangable. The aluminium panel allows for added security and blocks out view of your goods in the load bed area of your vehicle.
Consists of:1x Aluminium panelMaterials used:Black powder-coated AluminiumProduct Dimensions:705mm (27.8") W x 440mm (17.3") H x 6mm (0.2") DWeight:3.16kg (7lbs)
FRONT RUNNER Toyota Land Cruiser 76 Gullwing Window Panel /...
$521.10
$579.00
The Gullwing Window Panel is a replacement part for your Front Runner Gullwing Window.
This Glass Gullwing Window Panel is sold as a seperate component in order to replace a damaged window panel.
If you currently own an Aluminium Gullwing Window and would like to swap out your aluminium panel for a glass panel, the Gullwing Window's Panel has been designed to be interchangable. The glass panel blends in well to the Land Cruiser 76's exterior style and allows you to peer into your load bed area for ease of access to your goods.
Consists of:1x Glass panelMaterials used:Tinted and toughened 6mm glassProduct Dimensions:705mm (27.8") W x 440mm (17.3") H x 6mm (0.2") DWeight:5.39kg (11.9lbs)Glass specifications:Visible Light:Transmission: 44Reflection Outside: 5Solar Energy:Total Elimination: 38Reflection Outside: 5Absorption 1: 47Direct Transmission: 47SHGC: 0.62Shading Coefficient:Ratio: 0.71U Value:(W/m2).K (Center of Glass): 5.8
FRONT RUNNER Cargo Slide/Fridge Slide / 80L To 90L -...
$530.10
$589.00
Front Runner Cargo Slide / Fridge Slide 80L–90L
The Front Runner Cargo Slide / Fridge Slide 80L–90L is a heavy-duty storage solution designed to provide quick and convenient access to larger portable fridges, camping equipment, toolboxes, and adventure gear. Ideal for 4WDs, canopies, ute trays, drawer systems, and touring vehicles, the slide maximises accessibility while maintaining a compact footprint.
Built with high-strength bearing drawer slides, the tray extends nearly 100% from its anchored base, allowing easy access to equipment without climbing into your vehicle. The rattle-free design keeps your cargo secure during travel, while the clip latch locking system prevents unwanted movement when closed.
Constructed from durable black powder-coated steel and featuring a hold-open mechanism for uneven terrain, the Front Runner Cargo Slide is engineered for demanding off-road, touring, camping, and worksite environments.
Features
Suitable for 80L–90L portable fridges
High-strength bearing drawer slide mechanism
Nearly 100% tray extension for easy access
Rattle-free design during travel
Clip latch locking system
Hold-open mechanism for uneven surfaces
Mounts to most flat surfaces
Compatible with Front Runner Drawer Systems
Pre-drilled mounting holes for simple installation
Includes mounting hardware for wood and metal surfaces
Heavy-duty black powder-coated steel construction
Ideal for fridges, storage boxes, tools, and touring equipment
Specifications
Overall / Closed Dimensions: 942mm x 578mm x 85mm
Open Dimensions: 1858mm x 578mm x 85mm
Internal Dimensions: 884mm x 507mm x 64mm
Weight: 18.2kg
Load Rating: 113kg (250lbs)
Material: Black Powder-Coated Steel
What's Included
1 x Front Runner Cargo Slide
Installation Hardware
Fitting Instructions
Frequently Asked Questions
What fridge sizes will fit this Front Runner Cargo Slide?
This model is designed for many popular portable fridges in the 80L–90L range. We recommend comparing your fridge dimensions with the tray measurements before purchasing.
Can this Cargo Slide be installed in a canopy, ute tray, or drawer system?
Yes. The slide can be mounted to most suitable flat surfaces, including canopies, ute trays, drawer systems, and touring vehicle storage setups.
Does the slide lock securely during travel?
Yes. The integrated clip latch locking system and rattle-free design help keep your fridge and equipment secure while driving on-road and off-road.
Note: Fridges, storage containers, and accessories shown are sold separately.
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,458.90
$1,621.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to six (6) supplied Feet that slide in to the supplied Track. The 1400mm/55.1" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA001T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 1358mm(L) - by Front RunnerConsisting of:3x FASS024 - Foot Set / 50mm - 60mm1x RRSTA07 - SLII Tray - 1165mm(W)X1358mm(L)1x TRAC002 - Universal Track / 1400mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 25.89kg (57.08lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 445mm (18")Length: 1730mm (68")Height: 265mm (10")Shipping Weight:Weight: 29kg (64lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,357.20
$1,508.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1560mm/61.4" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA001TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1560mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA08 - Slimline II Tray - 1165mm(W) X 1560mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 21kg (47lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")Shipping Weight:
Weight 25.0kg (55.0lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,233.90
$1,371.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1156mm/45.5" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 1150mm/45.3" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA004T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 1156mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA06 - Slimline II Tray - 1165mm(W) X 1156mm(L) - by Front Runner1 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 20kg (43lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot, Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 22.9kg (50.4lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,072.80
$1,192.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1156mm/45.5" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA004TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1156mm(L) - by Front Runner
Consisting of
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA06 - Slimline II Tray - 1165mm(W) X 1156mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 18kg (39lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 20.7kg (45.6lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,261.80
$1,402.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA005TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1358mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 20kg (44lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 450mm (18")Length 1615mm (64")Height 140mm (6")
Shipping Weight:
Weight 23.1kg (50.9lbs)
FRONT RUNNER Pickup Truck Canopy Or Trailer Slimline Ii Rack...
$1,239.30
$1,377.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1345mm/53" (W) x 954mm/37.6" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 1000mm/39.4" long pair of tracks can be easily mounted to your canopy/shell or trailer. See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA006T - Truck Canopy/Trailer SLII Rack Kit 1345(W)x954(L)Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x RRSTG05 - SLII Tray - 1345mm(W)X954mm(L)1x TRBU001 - Pick-Up Load Bed Tracks / 1000mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 19.03kg (41.95lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 445mm (18")Length: 1720mm (68")Height: 280mm (11")Shipping Weight:Weight: 24kg (53lbs)
FRONT RUNNER Canopy Load Bar Kit / 1165Mm (W) -...
$495.00
$550.00
A set of Load Bars with Track Mounted Feet used to transport gear on the roof of your vehicle when there’s no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 40mm Feet, 2 1165mm Load Bars, 2 1150mm Canopy Tracks, and fitting instructions - all the components necessary to mount the Front Runner Load Bars to the vehicle.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner Load Bars.These Load Bars are mounted to the vehicle’s roof via a set of supplied Tracks and Track Mounted Feet.Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.Made from stainless steel and a durable, weather resistant black powder-coated aluminum.Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA007 - Canopy Load Bar Kit / 1165mm (W) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x LBSK013 - Load Bar Pair 1165mm(W) - by Front Runner1 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 7kg (14lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle’s rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions:
Width 245mm (10")Length 1290mm (51")Height 115mm (5")
Shipping Weight:
FRONT RUNNER Rsi Double Cab Smart Canopy Load Bar Kit...
$364.50
$405.00
Clear up precious interior space and still get your adventure gear anywhere with the help of these low-profile, lightweight Front Runner Load Bars for your RSI DC Smart Canopy.
A set of Load Bars used to transport gear on the roof of your RSI Double Cab Smart Canopy. This low profile solution includes 4 mounting Feet, 2 1255mm Load Bars, installation kit and fitting instructions.
These Load Bars are mounted to the RSC Double Cab Smart Canopy via a set of supplied Mounted Feet.
Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The Load Bars and mounting system can be used in the future as components to build a complete Front Runner Roof Rack.
Made from stainless steel and a durable, weather resistant black powder-coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA008 - RSI Double Cab Smart Canopy Load Bar Kit / 1255mm - by Front RunnerConsisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK014 - Roof Load Bar Pair 1255mm(W)2x RRAC921 - Canopy Rack Kit Installation SetMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 5.44kg (11.99lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 110mm (4")Length: 1380mm (54")Height: 150mm (6")Shipping Weight:Weight: 5.6kg (12lbs)
FRONT RUNNER Rsi Double Cab Smart Canopy Slimline Ii Rack...
$1,286.10
$1,429.00
This kit creates a full size rack on a RSI Canopy with a roof top size of approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to supplied Feet that slide in to the canopy track.
This kit creates a full size rack on a RSI Canopy with a roof top size of approximately 1165mm/45.9" (W) x 1358mm/53.5" (L). The Slimline II Tray mounts to supplied Feet that slide in to the canopy track.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*Note: This Kit does not fit Volkswagen Amarok Double Cab Canopies. Please use .
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA008T - RSI Double Cab Smart Canopy Slimline II Rack Kit / 1165mm(W) x 1358mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner3 x RRAC921 - Canopy Rack Kit Installation Set1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner
Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steel
Approximate Installed Weight: 23.3kg (51.4lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 450mm (18.0")Length: 1615mm (64.0")Height: 140mm (6.0")
Shipping Weight:23.1kg (51.0lbs)
FRONT RUNNER Canopy Load Bar Kit / 1345Mm - KRCA010
$360.90
$401.00
The Canopy Load Bar Kit was made for travelers who need additional canopy storage capacity, but don’t want to sacrifice a low-profile build. These 1345mm bars use the same durable aluminum slats as the Slimline II Roof Rack, allowing you to mount Front Runner accessories.
Comes with all hardware and components needed to fit load bars on a vehicle, including four (4) mounting feet, two (2) 1345mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA0010 - Canopy Load Bar Kit / 1345mm - by Front Runner
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK015 - Roof Load Bar Pair 1345mm(W)
Material Used:Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 6kg (13.23lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 110mm (4")Length: 1455mm (58")Height: 135mm (6")
Shipping Weight:Weight: 5.18kg (11.42lbs)
FRONT RUNNER Canopy Load Bar Kit / 1475Mm - KRCA011
$378.90
$421.00
The Canopy Load Bar Kit was made for travelers who need additional canopy storage capacity, but don’t want to sacrifice a low-profile build. These 1475mm bars use the same durable aluminum slats as the Slimline II Roof Rack, allowing you to mount Front Runner accessories.
Comes with all hardware and components needed to fit load bars on a vehicle, including four (4) mounting feet, two (2) 1475mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA0011 - Canopy Load Bar Kit / 1475mm - by Front Runner
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material Used:Black epoxy powder - coated T6 aluminium
Approximate Installed Weight: 6kg (13.23lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:Width: 110mm (4")Length: 1585mm (63")Height: 135mm (6")
Shipping Weight:Weight: 5.6kg (12lbs)
FRONT RUNNER Canopy Load Bar Kit / 1255Mm (W) -...
$348.30
$387.00
Load up adventure sports gear such as bikes, kayaks, and fishing rods on your pickup truck’s canopy with these load bars. This Canopy Load Bar Kit is specially designed to fit on a shorter (1255mm) canopy via a set of supplied mounted feet without compromising the canopy. These load bars are compatible with a variety of Front Runner accessories thanks to the sliding bolt t-slots.
Comes with all hardware and components needed to fit load bars on your canopy, including four (4) mounting feet, two (2) 1255mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
* Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA012 - Canopy Load Bar Kit / 1255mm (W)Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK014 - Roof Load Bar Pair 1255mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 5.3kg (11.68lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 110mm (4")Length: 1350mm (53")Height: 145mm (6")Shipping Weight:Weight: 6kg (13lbs)
FRONT RUNNER Canopy Load Bar Kit / 1425Mm (W) -...
$369.90
$411.00
Upgrade your pickup truck’s carrying capacity and easily transport adventure sports gear such as bikes, kayaks, and fishing rods with this Canopy Load Bar Kit. These bars are custom-designed to be mounted on a 1425mm canopy via a set of supplied mounted feet without compromising the canopy. Easily kit out your rig with a variety of compatible Front Runner accessories thanks to the sliding bolts t-slots which allow for quick fitting and removal.
Comes with all hardware and components needed to fit load bars on your Canopy, including four (4) mounting feet, two (2) 1425mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA013 - Canopy Load Bar Kit / 1425mm (W)Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK016 - Roof Load Bar Pair 1425mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 5.8kg (12.79lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 110mm (4")Length: 1500mm (59")Height: 145mm (6")Shipping Weight:Weight: 6kg (13lbs)
FRONT RUNNER Canopy Load Bar Kit / 1575Mm (W) -...
$405.90
$451.00
Upgrade your pickup truck’s carrying capacity and easily transport adventure sports gear such as bikes, kayaks, and fishing rods with this Canopy Load Bar Kit. These bars are custom-designed to be mounted on a canopy via a set of supplied mounted feet without compromising the canopy. Easily kit out your rig with a variety of compatible Front Runner accessories thanks to the sliding nut t-slots which allow for quick fitting and removal.
Comes with all hardware and components needed to fit load bars on your Canopy, including four (4) mounting feet, two (2) 1575mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA014 - Canopy Load Bar Kit / 1575mm (W) - by Front RunnerConsisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK018 - Roof Load Bar Pair 1575mm(W)Material Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 5.98kg (13.18lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 110mm (4")Length: 1670mm (66")Height: 145mm (6")Shipping Weight:Weight: 6kg (13lbs)
FRONT RUNNER Rsi Canopy Full Size Pickup Load Bar Kit...
$377.10
$419.00
Massively increase the cargo-carrying capacity of your RSI Canopy by installing this durable Load Bar Kit on top of it. Load bars attach to the canopy using the supplied feet and they have the same T-slots as slats as a Front Runner roof rack, so you can fit rack accessories to it.
Includes all hardware and components needed to fit load bars on your Full Pickup when fitted with a RSI Canopy, including four (4) mounting feet, two (2) 1345mm load bars, an installation kit and fitting instructions.
These load bars are mounted to your RSI Canopy via a set of supplied mounted feet.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The load bars and mounting system can be used in the future as components to build a complete Front Runner roof rack.
Made from steel and durable, weather-resistant black powder-coated aluminum.
Note: The load per Load Bars must not exceed 55lbs or 25kg, and ensure the load is distributed evenly. For larger loads, additional Load Bars may be needed, please contact Customer Service for any enquiries.
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA016 - RSI Canopy Full Size Pickup Load Bar Kit / 1345mmConsisting of:2x FASS024 - Foot Set / 50mm - 60mm1x LBSK015 - Roof Load Bar Pair 1345mm(W)2x RRAC921 - Canopy Rack Kit Installation SetMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 5.18kg (11.42lbs)The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above.If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters.If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 115mm (5")Length: 1450mm (57")Height: 155mm (6")Shipping Weight:Weight: 5kg (11lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,321.20
$1,468.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 1358mm/53.5" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA020TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1255mm(W) X 1358mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTD07 - Slimline II Tray - 1255mm(W) X 1358mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 21kg (47lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 630mm (25")Length 1640mm (65")Height 160mm (6")
Shipping Weight:
Weight 24.6kg (54.2lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,518.30
$1,687.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4 (W) x 1358mm/53.5 (L). The Slimline II Tray mounts to six (6) supplied Feet that slide in to the supplied Track. The 1400mm/55.1 in. long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
Depth (in):10.600000
Length (mm):440.000000
Weight (kg):29.0
Width (mm):1730.000000
Depth (mm):270.000000
Specification:KRCA021T - Truck Canopy or Trailer Slimline II Rack Kit / 1255mm(W) x 1358mm(L) - by Front Runner Consisting of: 3x FASS024 - Foot Set / 50mm - 60mm1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)1x TRAC002 - Universal Track / 1400mm(L) Material Used:
Weight (lbs):63.9
Country of Origin: ZA
Length (in):17.300000
UPC:6009542238807
Width (in):68.100000
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,420.20
$1,578.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 1560mm/61.4" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA021TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1255mm(W) X 1560mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTD08 - Slimline II Tray - 1255mm(W) X 1560mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 23kg (50lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 630mm (25")Length 1640mm (65")Height 160mm (6")Shipping Weight:
Weight 26.6kg (58.6lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$838.80
$932.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 752mm/29.6" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA023TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 752mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA04 - Slimline II Tray - 1165mm(W) X 752mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 15kg (33lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 752mm (30")Height 50mm (2")
Shipping Weight:
Weight 17.3kg (38.1lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$955.80
$1,062.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 954mm/37.6" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA024TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 954mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA05 - Slimline II Tray - 1165mm(W) X 954mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 16kg (36lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 954mm (38")Height 50mm (2")
Shipping Weight:
Weight 18.9kg (41.5lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,519.20
$1,688.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1762mm/69.4" (L). The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA025TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1762mm(L) - by Front Runner
Consisting of:
3 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA09 - Slimline II Tray - 1165mm(W) X 1762mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 23kg (51lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 1762mm (69")Height 50mm (2")Shipping Weight:
Weight 27.1kg (59.7lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,775.70
$1,973.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1762mm/69.4" (L). The Slimline II Tray mounts to eight (8) supplied Feet that slide in to the supplied Track. The 1600mm/63" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA026T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 1762mm(L) - by Front RunnerConsisting of:4x FASS024 - Foot Set / 50mm - 60mm1x RRSTA09 - SLII Tray - 1165mm(W)X1762mm(L)1x TRCA010 - Canopy Tracks / 1600mm (L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 27.26kg (60.1lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 445mm (18")Length: 1730mm (68")Height: 270mm (11")Shipping Weight:Weight: 32.8kg (72lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,695.60
$1,884.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 1964mm/77.3" (L). The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA026TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 1964mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA10 - Slimline II Tray - 1165mm(W) X 1964mm(L) - by Front RunnerMaterial used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 26kg (57lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 1964mm (77")Height 50mm (2")
Shipping Weight:
Weight 29.9kg (65.8lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$2,064.60
$2,294.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2166mm/85.3" (L). The Slimline II Tray mounts to eight (8) supplied Feet that slide in to the supplied Track. The 2 x 750mm/29.5" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA027T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 2166mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA11 - Slimline II Tray - 1165mm(W) X 2166mm(L) - by Front Runner2 x TRCA005 - Canopy Tracks / 750mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 30kg (66lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2166mm (85")Height 50mm (2")
Shipping Weight:
Weight 35.0kg (77.0lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,821.60
$2,024.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2166mm/85.3" (L). The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA027TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 2166mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA11 - Slimline II Tray - 1165mm(W) X 2166mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 27kg (60lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2166mm (85")Height 50mm (2")
Shipping Weight:
Weight 31.8kg (69.8lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$2,176.20
$2,418.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2368mm/93.2" (L). The Slimline II Tray mounts to eight (8) supplied Feet that slide in to the supplied Track. The 2 x 750mm/29.5" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA028T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 2368mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA12 - Slimline II Tray - 1165mm(W) X 2368mm(L) - by Front Runner2 x TRCA005 - Canopy Tracks / 750mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 32kg (70lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2368mm (93")Height 50mm (2")
Shipping Weight:
Weight 36.8kg (81.0lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,933.20
$2,148.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2368mm/93.2" (L). The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA028TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 2368mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA12 - Slimline II Tray - 1165mm(W) X 2368mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 29kg (64lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2368mm (93")Height 50mm (2")Shipping Weight:
Weight 33.6kg (73.9lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$2,368.80
$2,632.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2570mm/101.2" (L). The Slimline II Tray mounts to eight (8) supplied Feet that slide in to the supplied Track. The 2 x 1150mm/45.3" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA029T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 2570mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA13 - Slimline II Tray - 1165mm(W) X 2570mm(L) - by Front Runner2 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 35kg (77lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2570mm (101")Height 50mm (2")
Shipping Weight:
Weight 40.5kg (89.0lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$2,046.60
$2,274.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2570mm/101.2" (L). The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA029TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 2570mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA13 - Slimline II Tray - 1165mm(W) X 2570mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 31kg (68lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2570mm (101")Height 50mm (2")
Shipping Weight:
Weight 35.8kg (78.7lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$2,485.80
$2,762.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2772mm/109.1" (L). The Slimline II Tray mounts to eight (8) supplied Feet that slide in to the supplied Track. The 2 x 1150mm/45.3" long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
KRCA030T - Truck Canopy or Trailer Slimline II Rack Kit / 1165mm(W) X 2772mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA14 - Slimline II Tray - 1165mm(W) X 2772mm(L) - by Front Runner2 x TRCA003 - Canopy Tracks / 1150mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 36kg (79lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2772mm (109")Height 50mm (2")
Shipping Weight:
Weight 42.0kg (92.4lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$2,163.60
$2,404.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1165mm/45.9" (W) x 2772mm/109.1" (L). The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA030TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1165mm(W) X 2772mm(L) - by Front Runner
Consisting of:
4 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTA14 - Slimline II Tray - 1165mm(W) X 2772mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 32kg (71lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1165mm (46")Length 2772mm (109")Height 50mm (2")Shipping Weight:
Weight 37.3kg (82.1lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$999.90
$1,111.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 752mm/29.6" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 750mm/29.5” long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA031T - Truck Canopy or Trailer Slimline II Rack Kit / 1255mm(W) X 752mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTD04 - Slimline II Tray - 1255mm(W) X 752mm(L) - by Front Runner1 x TRCA005 - Canopy Tracks / 750mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 17kg (38lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1255mm (49")Length 752mm (30")Height 50mm (2")
Shipping Weight:
Weight 19.9kg (43.8lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$878.40
$976.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 752mm/29.6" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA031TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1255mm(W) X 752mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTD04 - Slimline II Tray - 1255mm(W) X 752mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 16kg (35lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1255mm (49")Length 752mm (30")Height 50mm (2")Shipping Weight:
Weight 18.3kg (40.3lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,125.90
$1,251.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 954mm/37.6" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 750mm/29.5” long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
Consisting of:2x FASS024 - Foot Set / 50mm - 60mm1x RRSTD05 - SLII Tray - 1255mm(W)X954mm(L)1x TRCA005 - Canopy Tracks / 750mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 20.63kg (45.48lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 440mm (17")Length: 1730mm (68")Height: 270mm (11")Shipping Weight:Weight: 20.8kg (46lbs)
FRONT RUNNER Ute Canopy Or Trailer With Oem Track Slimline...
$1,004.40
$1,116.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 954mm/37.6" (L). The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer.NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have:
Slot base width min 20mm / max 25mm
Slot base height min 6.5mm / max 10mm
Slot opening width min 8.5mm / max 10.5mm
Slot opening height min 2mm / max 5mm
**Please check with canopy manufacturer regarding the load ratings for your specific canopy and track.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA032TN - Truck Canopy or Trailer with OEM Track Slimline II Rack Kit / 1255mm(W) X 954mm(L) - by Front Runner
Consisting of:
2 x FASS024 - Foot Set / 50mm-60mm - by Front Runner1 x RRSTD05 - Slimline II Tray - 1255mm(W) X 954mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminiumHigh strength steel
Approximate Installed Weight 17kg (37lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:
Width 1255mm (49")Length 954mm (38")Height 50mm (2")
Shipping Weight:
Weight 19.4kg (42.7lbs)
FRONT RUNNER Ute Canopy Or Trailer Slimline Ii Rack Kit...
$1,287.90
$1,431.00
This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1255mm/49.4" (W) x 1156mm/45.5" (L). The Slimline II Tray mounts to four (4) supplied Feet that slide in to the supplied Track. The 1150mm/45.3” long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit.
KRCA033T - Truck Canopy or Trailer Slimline II Rack Kit / 1255mm(W) X 1156mm(L) - by Front RunnerConsisting of:2x FASS024 - Foot Set / 50mm - 60mm1x RRSTD06 - SLII Tray - 1255mm(W)X1156mm(L)1x TRCA003 - Canopy Tracks / 1150mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 23.45kg (51.7lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 445mm (18")Length: 1730mm (68")Height: 270mm (11")Shipping Weight:Weight: 23.4kg (51lbs)
LIGHTFORCE BEAST 230 Super Bundle — Driving Lights (pair) and...
$1,129.00
$1,352.00
LIGHTFORCE BEAST 230 3-Mode Driving Light Ultimate Bundle
Upgrade your vehicle lighting with the complete LIGHTFORCE BEAST 230 Ultimate Bundle. Designed for off-road enthusiasts, touring vehicles, and professional applications, this all-in-one kit delivers maximum visibility, durability, and ease of installation.
This bundle includes a pair of powerful BEAST 230 LED driving lights and a dedicated plug-and-play wiring harness for a complete lighting upgrade.
What’s Included
LIGHTFORCE BEAST 230 LED Driving Light - Pair (3-Mode) – BEAST230PK
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play solution with no additional parts required
3 beam modes: Spot, Flood, and BEAST for versatile driving conditions
Extended beam distance and wider spread for maximum visibility
Heavy-duty construction designed for extreme environments
Quick and easy installation with included wiring harness
BEAST 230 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
High-output LED performance for long-range and wide visibility
Optimised beam pattern for off-road and highway use
5700K colour temperature for clear, natural visibility
Large format design for increased light output and coverage
Daytime Running Light (DRL) functionality
Heavy-duty aluminium housing for durability and heat management
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Single 8-pin connector for clean installation
Includes relay, rocker switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
Impact-resistant construction for harsh environments
Operating temperature range: -40°C to 85°C
Resistant to UV, salt spray, and corrosion
Long-lasting LED lifespan
Specifications
Light Size: 230mm
Voltage: 12V system compatible
Colour Temperature: 5700K
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Rural and low-light environments
Why Choose LIGHTFORCE BEAST 230 Bundle
This bundle provides a complete, professional-grade lighting solution with industry-leading performance and durability. With advanced beam technology and simple installation, it is the ideal upgrade for drivers who demand reliability and visibility.
Order now to upgrade your driving visibility with a complete BEAST lighting setup.
LIGHTFORCE BEAST 190 Ultimate Bundle — Pair of Driving Lights...
$999.00
$1,150.00
LIGHTFORCE BEAST 190 Ultimate Bundle – 3-Mode Pair Of Driving Lights with Wiring Harness
The LIGHTFORCE BEAST 190 Ultimate Bundle is a complete high-performance lighting solution designed for off-road, touring, and demanding driving conditions. This bundle combines the powerful BEAST 190 LED driving lights with a dedicated 3-mode wiring harness for a simple, professional installation.
Engineered and manufactured in Australia, the BEAST 190 delivers exceptional beam distance, width, and durability in a compact 190mm design. With three selectable beam modes, this system allows you to adapt instantly to changing environments for maximum control and confidence.
What’s Included
2 X LIGHTFORCE BEAST 190 LED Driving Light – BEAST190X1
BEAST 3-Mode Universal Wiring Harness Kit – LFDLHBEAST-U
Key Benefits
Complete plug-and-play lighting solution
3 beam modes: Spot, Flood, and BEAST
Up to 1260m beam distance for long-range visibility
Compact design with extreme durability
Quick and easy installation with dedicated wiring harness
BEAST 190 Driving Light Features
3-mode beam operation: Spot, Flood, and BEAST mode
Up to 1 lux at 1260m (pair) for long-distance performance
25 high-performance Osram LEDs
5700K colour temperature for clear, natural visibility
Compact 190mm size with ultra-slim 80mm depth
Daytime Running Light (DRL) functionality
Pressure die-cast aluminium housing for strength and heat dissipation
Beam Modes
Spot Mode: Long-distance beam up to 1195m
Flood Mode: Wide beam up to 496m
BEAST Mode: Combined distance and width up to 1260m
Wiring Harness Features
Designed specifically for BEAST 3-mode driving lights
True plug-and-play installation with no rewiring required
Includes HB3 and H4 headlight adaptors
Automatic positive and negative switching compatibility
Includes relay, switch, and mounting hardware
Durability and Performance
IP69K waterproof and dustproof rating
IK16 impact resistance for extreme durability
Operating temperature range from -40°C to 85°C
Resistant to UV, salt spray, and corrosion
LED lifespan up to 50,000 hours
Specifications
Diameter: 190mm
Depth: 80mm
Weight: 1.6kg
Voltage: 13.2V
Ingress Rating: IP69K
Colour Temperature: 5700K
Warranty: 5 Years
Designed For
4WD and off-road vehicles
Touring and long-distance driving
Work and utility vehicles
Low-light and rural environments
Why Choose This Bundle
This bundle delivers a complete, professional-grade lighting upgrade with everything required for installation. Combining advanced LED performance, versatile beam control, and enhanced durability, it is ideal for drivers who demand reliability and maximum visibility in all conditions.
Upgrade your setup with the LIGHTFORCE BEAST 190 Ultimate Bundle today.
ALPINE LC70 Ultimate Status Audio & Camera Bundle, Speakers +...
$6,930.00
$7,700.00
ALPINE LC70 Ultimate Status Audio and Camera Bundle – Complete Premium Sound System
The ALPINE LC70 Ultimate Status Bundle is the complete high-end audio and safety upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining Alpine’s advanced i905-LC70 head unit, R2-Series speaker system, Alpine Status HDA-V90 amplifier, RS-SB10 shallow subwoofer, and rear view camera, this bundle delivers exceptional sound quality, powerful bass, and enhanced driving visibility.
Built using Alpine’s latest Hi-Res Audio technology, this system delivers a true high-resolution listening experience with precision, clarity, and depth, while maintaining seamless factory-style integration.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE HDA-V90 5-Channel Hi-Res Audio Amplifier
ALPINE RS-SB10 Shallow Subwoofer Enclosure
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete premium audio and safety system in one bundle
Hi-Res Audio performance with powerful, detailed sound
Deep, controlled bass from shallow subwoofer design
High-output 5-channel amplifier for full system control
Wireless Apple CarPlay and Android Auto connectivity
Improved reversing safety with rear view camera
Seamless integration for LandCruiser 70 Series Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier and advanced sound tuning
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for accurate sound reproduction
Glass-fibre reinforced cones for clarity and response
HAMR surround for enhanced bass performance
Integrated door pods with USB charging and storage
HDA-V90 Amplifier Features
5-channel Class-D amplifier with Hi-Res Audio certification
Frequency response: 10Hz – 60kHz
75W x 4 + 300W x 1 @ 4Ω output
100W x 4 + 500W x 1 @ 2Ω output
High damping factor for precise speaker control
Low distortion for clean and accurate sound
RS-SB10 Subwoofer Features
Shallow 12-inch high-performance subwoofer enclosure
600W RMS and 1800W peak power handling
Ultra-compact design for flexible installation
Neodymium magnet for high efficiency and power
20mm X-max for deep, controlled bass output
Rear View Camera Features
Wide viewing angle for improved rear visibility
HDR technology for clear image in low light conditions
Automatic activation when reversing
Day and night image adjustment
System Performance
High-resolution audio playback across full system
Powerful amplified output with deep bass response
Balanced sound staging with precise tuning capability
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete premium audio system
Off-road and touring vehicles
Users wanting high-performance sound and added safety
Why Choose This Bundle
This bundle represents the ultimate Alpine upgrade, combining industry-leading components into one complete system. Designed for performance, clarity, and reliability, it delivers a superior in-car experience with powerful sound, deep bass, and enhanced safety features.
Transform your LandCruiser 70 Series with Alpine’s ultimate audio and camera system.
ALPINE LC70 Premium Audio Bundle — Head Unit + Speakers
$4,679.91
$5,199.90
ALPINE LC70 Premium Audio Bundle – i905-LC70 Head Unit with R2-Series Speaker Upgrade
The ALPINE LC70 Premium Audio Bundle is the ultimate in-car sound upgrade for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 9-inch multimedia receiver with Alpine’s R2-Series door pod speaker system, this bundle delivers powerful, high-resolution audio with seamless factory-style integration.
Designed for both performance and practicality, this setup transforms your vehicle into a premium listening environment while enhancing interior functionality and aesthetics.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
Key Benefits
Complete premium audio upgrade for LandCruiser 70 Series Dual Cab
High-resolution sound with powerful bass and clarity
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration with modern design enhancement
Additional functionality with storage, USB charging, and lighting
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
Seamless integration designed for LC70 interior
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear for powerful output
Hi-Res Audio certified for accurate and detailed sound
Glass-fibre reinforced cones for fast response and clarity
HAMR surround for increased bass performance and control
Neodymium magnet structure for improved efficiency
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated front and rear speaker pods
Built-in USB charging ports (up to 4 devices)
Integrated puddle lighting for improved visibility at night
Storage compartments for bottles, maps, and accessories
Durable injection-moulded PC/ABS construction
Performance Specifications
Peak Power Handling: 300W
RMS Power Handling: 100W
Nominal Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Woofer Size: 6x9 inch
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers upgrading factory audio systems
Off-road and touring vehicles
Users seeking premium sound quality and modern connectivity
Why Choose This Bundle
This bundle delivers a complete, high-performance audio upgrade with seamless integration, powerful sound output, and added interior functionality. Designed specifically for the LC70, it combines Alpine’s industry-leading technology with practical features for everyday use and off-road adventures.
Upgrade your LandCruiser 70 Series with Alpine’s premium audio solution today.
ALPINE LC70 Ultimate Audio System Bundle — Head Unit +...
$5,309.87
$5,899.85
ALPINE LC70 Ultimate Audio System Bundle – Head Unit, Speaker Upgrade and Amplifier
The ALPINE LC70 Ultimate Audio System Bundle is a complete premium sound upgrade designed specifically for Toyota LandCruiser 70 Series (Dual Cab). Combining the advanced i905-LC70 multimedia receiver, Alpine R2-Series speaker door pod system, and the powerful R2-A60F amplifier, this bundle delivers exceptional clarity, depth, and power.
Engineered for audiophiles and off-road enthusiasts, this system transforms your vehicle into a high-performance listening environment with seamless factory-style integration and modern connectivity.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE R2-Series Door Pod Speaker Kit (Front and Rear) – LC70-R269P
ALPINE R2-A60F Class-D Digital Amplifier
Key Benefits
Complete premium audio system upgrade in one bundle
High-resolution sound with powerful bass and clarity
Amplified performance for maximum output and control
Wireless Apple CarPlay and Android Auto connectivity
Factory-style integration designed for LC70 Dual Cab
i905-LC70 Head Unit Features
9-inch WXGA high-definition display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for dynamic sound performance
Advanced sound tuning for customised audio control
R2-Series Speaker System Features
6x9-inch R2-Series speakers front and rear
Hi-Res Audio certified for detailed and accurate sound
Glass-fibre reinforced cones for fast response
HAMR surround for increased bass performance
High-pass crossover network with adjustable tweeter levels
Door Pod Kit Features
Direct-fit design for LandCruiser 70 Series Dual Cab
Integrated speaker pods front and rear
Built-in USB charging ports for up to 4 devices
Integrated puddle lighting for improved visibility
Storage compartments for everyday convenience
Durable PC/ABS construction for long-lasting use
R2-A60F Amplifier Features
Compact Class-D digital amplifier with reduced footprint
Hi-Res Audio certified up to 45kHz
Top panel sound controls for easy tuning
One-sided terminal layout for simplified installation
100W RMS x 4 @ 4Ω output
150W RMS x 2 @ 2Ω output
300W RMS x 2 @ 4Ω bridged
Frequency response: 10Hz – 45,000Hz
High damping factor for improved speaker control
Performance Specifications
Speaker Peak Power: 300W
Speaker RMS Power: 100W
Impedance: 4 ohms
Frequency Response: 60Hz – 40kHz
Perfect For
Toyota LandCruiser 70 Series Dual Cab
Drivers seeking a complete audio system upgrade
Off-road and touring vehicles
Users wanting powerful, high-quality sound performance
Why Choose This Bundle
This bundle delivers a complete, high-performance audio solution combining premium components for superior sound quality, power, and control. Designed specifically for the LC70, it ensures seamless integration while providing a significant upgrade over factory audio systems.
Upgrade your LandCruiser 70 Series with Alpine’s ultimate audio system bundle today.
ALPINE LC70 Premium Head Unit & Reverse Camera Bundle —...
$2,789.91
$3,099.90
ALPINE LC70 Premium Head Unit and Reverse Camera Bundle – i905-LC70 with HCE-C1100 Camera
The ALPINE LC70 Premium Bundle combines cutting-edge infotainment with enhanced driving safety, designed specifically for Toyota LandCruiser 70 Series. Featuring the advanced i905-LC70 9-inch multimedia receiver and the HCE-C1100 rear view camera, this bundle delivers seamless connectivity, high-resolution audio, and improved visibility when reversing.
Upgrade your dashboard with a modern, integrated system that enhances both your driving experience and vehicle functionality.
What’s Included
ALPINE i905-LC70 9” Integrated Hi-Res Audio Receiver
ALPINE HCE-C1100 Rear View Drive Assist Camera
Key Benefits
Complete infotainment and safety upgrade in one bundle
Wireless Apple CarPlay and Android Auto connectivity
High-definition 9-inch WXGA display
Enhanced reversing visibility with wide-angle camera
Seamless integration designed for LandCruiser 70 Series
i905-LC70 Head Unit Features
9-inch WXGA high-resolution display
Wireless Apple CarPlay and Android Auto (USB)
Built-in TIDAL for Hi-Res music streaming
Supports Hi-Res audio up to 96kHz / 24-bit
Built-in Class-D amplifier for superior sound performance
Advanced sound tuning for custom audio control
Seamless integration with LandCruiser 70 Series interior
Rear View Camera Features
Wide viewing angle: 131° horizontal, 103° vertical
HDR technology for clear vision in low-light conditions
Automatic day and night image adjustment
RCA or direct Alpine connection compatibility
Automatic activation when reversing
Compact design with included mounting hardware
Camera Specifications
Resolution: 640 x 480
Waterproof rating: IP67
Power supply: DC5.0V – DC7.0V
Viewing angle: 131° horizontal, 103° vertical
Operating temperature: -30°C to +70°C
Designed For
Toyota LandCruiser 70 Series
Off-road and touring vehicles
Daily driving and work vehicles
Drivers seeking upgraded audio and safety
Why Choose This Bundle
This bundle delivers a complete in-car upgrade, combining premium audio performance with enhanced safety features. Designed specifically for the LandCruiser 70 Series, it ensures seamless integration, modern functionality, and improved driving confidence.
Upgrade your LandCruiser 70 Series with Alpine’s premium multimedia and camera solution today.
