All Discounted Car Parts & Accessories

Get your Ram 1500 ready for serious gear-carrying duties with the Slimsport Roof Rack. The sleek, low-profile Slimsport Roof Rack is form-fit to complement the aesthetic of your RAM and is compatible with 55+ accessories so you can kit up for any adventure. This low-profile flat deck Slimsport rack has a load carrying area of 1660mm (65.4") x 1380mm (54.3"). The sleek side rails have integrated mounting feet. The mounting feet also have additional brace brackets for added strength. The high-strength aluminum slats have T-slots suitable for all Front Runner top mount accessories. Easily add on the Rack Accessory Mounting Bracket Slimsport/Slimpro Van Side Mount Accessory Bracket / Small - by Front Runner for most Front Runner side mount accessories (sold separately). The included standard full fairing with rubber edge trim makes the rack ultra-quiet. Need a lightbar? The optional RAM 1500 Slimsport Rack 40" Light Bar Wind Fairing (sold separately) has a 40" cutout to allow the use of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount (sold separately). Fitment guide and all mounting hardware included. Note: Drilling required for installation. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: Under Rack Tables are not compatible with the Slimsport rack kit range Features KSDR002T - RAM 1500 Slimsport Roof Rack Kit Consisting of: 1x KSDR001 - Dodge Ram 1500 Slimsport Tray 1x RRAC279 - RAM 1500 Slimsport Rack Wind Fairing Material Used: Black epoxy powder - coated T6 aluminium High strength steel Assembled Rack Kit Dimensions: 1660mm (65.4") L x 1380mm (54.3") W x 152mm (6") H Approximate Installed Weight: 30.55kg (67.35lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicle's roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof. Shipping Dimensions: Width: 325mm (13") Length: 1700mm (67") Height: 225mm (9") Shipping Weight: Weight: 34kg (75lbs)

Enhance the performance of the Slimsport Roof Rack on your Ram 1500 with this smart Rack Wind Fairing. It will massively reduce wind noise and fuel consumption while allowing easy airflow over your rack and accessories-a great way to quieten your ride.   A wind fairing for the RAM 1500 Slimsport Roof Rack Kit. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Features Consists of: 1 x RAM 1500 Slimsport Rack Wind Fairing Installation Hardware Fitment Guide Materials used: Black powder-coated high strength steel Product Dimensions: 1371mm (54") L x 222mm (8.7") W x  x 210mm (8.3") H Weight: 4.4kg (9.7lbs)

Improve the performance of the Slimsport Rack on your Ram 1500 with this useful Light Bar Ready Wind Fairing. It accommodates a Slim 40" LED Light Bar while massively reducing wind noise and fuel consumption allowing easy airflow over the rack and accessories. It's a great way to quieten your ride.   Lightbar wind fairing for RAM 1500 Slimsport Roof Rack Kit / Lightbar Ready. Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount. Air flows easily over the rack and accessories, reducing drag and wind noise. Helps fuel consumption while carrying bulky loads. A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain. Brackets and installation hardware included. Features Consists of: 1 x RAM 1500 Slimsport Rack 40" Light Bar Wind Fairing Fitment Guide Installation Hardware Materials used: Black powder-coated high strength steel Product Dimensions: 1370mm (53.9") L x 200mm (7.9") W x 177mm (7") H Weight: 4kg (8.8lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 Quad Cab. This low profile solution includes 6 Pickup Roll Top Leg Mounts, 3 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from high strength steel and aluminum, protected with a weather-resistant black powder coat. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRDR021 - Ram 1500 6.4' Quad Cab (2009-Current) Triple Load Bar Kit - by Front Runner Consisting of: 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x LBSK019 - Roof Load Bar Set 1575mm(W) - by Front Runner 1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 16.6kg (36.7lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 390mm (15.0") Length: 1630mm (64.0") Height: 130mm (5.0") Shipping Weight: 16.4kg (36.0lbs)

This kit creates a full-size rack that sits above your RAM 1500 6.4' Quad Cab's truck bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1762mm), 2 Tracks, and 6 Pickup Truck Bed Universal Legs that fit into the Tracks. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Drilling may be required to mount the track to the bed of your truck. Features KRDR015T - RAM 1500 6.4' Quad Cab (2009-Current) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x RRSTP09 - SLII Tray - 1575mm(W)X1762mm(L) 1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 39.4kg (87.0lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 1730mm (68.0") Length: 445mm (18.0") Height: 290mm (11.0") Shipping Weight: 40.0kg (88.0lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 Crew Cab. This low profile solution includes 6 Pickup Roll Top Leg Mounts, 3 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRDR020 - Ram 1500 6.4' Crew Cab (2009-Current) Triple Load Bar Kit - by Front Runner Consisting of: 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x LBSK019 - Roof Load Bar Set 1575mm(W) - by Front Runner 1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 16.6kg (36.7lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 390mm (15.0") Length: 1630mm (64.0") Height: 130mm (5.0") Shipping Weight: 16.4kg (36.0lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 6.4' Crew Cab. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRDR017 - Ram 1500 6.4' Crew Cab (2009-Current) Double Load Bar Kit - by Front Runner Consisting of: 2 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x LBSK018 - Roof Load Bar Pair 1575mm(W) - by Front Runner 1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 12.2kg (26.9lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 300mm (12.0") Length: 1665mm (66.0") Height: 115mm (5.0") Shipping Weight: 12.2kg (27.0lbs)

This kit creates a full-size rack that sits above your RAM 1500 6.4' truck bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1762mm), 2 Tracks, and 6 Pickup Truck Bed Universal Legs that fit into the Tracks. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Drilling may be required to mount the track to the bed of your truck. Features KRDR014T - RAM 1500 6.4' (2009-Current) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x RRSTP09 - SLII Tray - 1575mm(W)X1762mm(L) 1 x TRBU004 - Bakkie Load Bed Tracks / 1600mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 39.4kg (87.0lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18.0") Length: 1730mm (68.0") Height: 290mm (11.0") Shipping Weight: 40.0kg (88.0lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 Crew Cab. This low profile solution includes 6 Pickup Roll Top Leg Mounts, 3 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from stainless steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRDR019 - Ram 1500 5.7' Crew Cab (2009 - Current) Triple Load Bar Kit - by Front Runner Consisting of: 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x LBSK019 - Roof Load Bar Set 1575mm(W) - by Front Runner 1 x TRBU002 - Bakkie Load Bed Tracks / 1200mm(L) - by Front Runner Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 15.9kg (35.0lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 380mm (15.0") Length: 1595mm (63.0") Height: 130mm (5.0") Shipping Weight: 15.6kg (34.0lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500 5.7' Crew Cab. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1575mm Load Bars, 1 set of Load Bed Tracks and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto a set of Load Bed Tracks. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Features KRDR016 - Ram 1500 5.7' Crew Cab (2009-Current) Double Load Bar Kit - by Front Runner Consisting of: 2 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 1 x LBSK018 - Roof Load Bar Pair 1575mm(W) - by Front Runner 1 x TRBU002 - Bakkie Load Bed Tracks / 1200mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 11.4kg (25.2lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 300mm (12.0") Length: 1665mm (66.0") Height: 115mm (5.0") Shipping Weight: 11.4kg (25.0lbs)

This kit creates a full-size rack that sits above your RAM 1500 5.7' truck bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1358mm), 2 Tracks that install on top of the side channel of the load bed, and 6 Pickup Truck Bed Universal Legs that fit into the Tracks. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Drilling may be required to mount the track to the bed of your truck. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR017T - RAM 1500 5.7' (2009-Current) Slimline II Top-Mount Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS027 - Leg Spacer 6mm (Pair)3x LASS038 - Pickup Roll Top/Top Mount Leg / Medium (Pair)1x RRAC939 - Pickup Load Bed Bolt Kit / 30mm1x RRSTP07 - SLII Tray - 1575mm(W)X1358mm(L)1x TRBU003 - Pick-Up Load Bed Tracks / 1400mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 35.6608kg (78.62lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 270mm (11")   Shipping Weight: Weight: 36kg (79lbs)

This kit creates a full-size rack that sits above your RAM 1500 5.7' truck bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1560mm), 2 Tracks, and 6 Pickup Truck Bed Universal Legs that fit into the Tracks. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Drilling may be required to mount the track to the bed of your truck. Features KRDR016T - RAM 1500 5.7' (2009-Current) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 1 x RRSTP08 - Slimline II Tray - 1575mm(W) X 1560mm(L) - by Front Runner 3 x LASS026 - Universal Load Bed Leg / Tall (Pair) - by Front Runner 2 x TRBU002 - Pickup Load Bed Tracks / 1200mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 26.4kg (58.2lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 445mm (17.5") Length 1730mm (68.1") Height 285mm (11.2")   Shipping Weight: Weight 31kg (68.3lbs)

This tough, lightweight steel and aluminum system secures to the bed of your Ram, thereby hugely increasing its gear-carrying capacity. This Pro Bed system is designed to fit a Front Runner rack and several accessories to its sides. These include molle panels, storage boxes or recovery tracks. It allows you to pack all the overland, camping or sports gear you may need. This Pro Bed System is specifically designed to fit the RAM 1500 (5Gen) 4 Door Crew Cab 5.7' load bed. This System provides the frame to customize your Load Bed storage configuration. Secures Pro Bed accessories, Wolf Pack Pro Cargo System Bracket, Pro Bed Rack Headache Molle Panel and a Pro Bed Universal Accessory Mount and is designed to mount a full Roof Rack and to haul more gear above it.  Secures to the load bed of the RAM 1500 (5Gen) 4 Door Crew Cab 5.7' with specific mounting brackets. Made of steel and is black powder-coated in the same durable and corrosion resistant coating as the Front Runner racks. The Pro Bed System have integrated hooks for more accessories such as the Dynamic Pro Bed Tailgate Net. Drilling is required for fitment. For further information on installation, please see the fitment instructions in the INSTALL tab. Features PBDR001S - RAM 1500 (5th Gen) 4 Door Crew Cab 5'7" Box (2019-Current) Pro Bed System Consisting of: 1x PBAL1450 - Pro Bed Rack Aluminium Extrusions / Large 1x PBDR001 - RAM 1500 (5th Gen) 4 Door Crew Cab 5'7" Box (2019-Current) 1x PBRA001 - Pro Bed Rack Universal Structural Components Material Used: Black epoxy powder - coated T6 aluminium Approximate Installed Weight: 53.13kg (117.13lbs) Shipping Dimensions: Width: 425mm (17") Length: 1490mm (59") Height: 615mm (24") Shipping Weight: Weight: 55kg (121lbs)

Get ready to massively up the gear-carrying capacity in the load bed area of your Ram 1500 (5'7" box) with our Pro Bed Rack Kit. Includes a Slimline II Roof Rack and Pro Bed System that is secured to the bed of your Ram. Attach a variety of Pro Bed accessories to the Pro Bed System, while all our 55+ other accessories can go on the rack - no excuses for leaving any gear behind. This Pro Bed Rack Kit is specifically designed to fit the RAM 1500 (5Gen) 4 Door Crew Cab 5.7' load bed. Included in this Kit is the a 1425mm/56.1" x 1560mm/61.4" Slimline II Rack and Pro Bed System. The Pro Bed Rack Kit provides the freedom to customize your Load Bed storage configuration. The Slimline II Rack allows all the top, side and under rack mounted adventure gear accessories.  The Pro Bed System secures Pro Bed accessories,  (Wolf Pack Pro Cargo System Bracket, Twin Wolf Pack Pro Cargo System Bracket, Pro Bed Rack Headache Molle Panel and a Pro Bed Universal Accessory Mount freeing up space on the Slimline II rack and in the bed of your truck. Secures to the bed of the RAM 1500 (5Gen) 4 Door Crew Cab with specific mounting brackets. Drilling is required for fitment. The Pro Bed System has integrated fixing points for more accessories such as the Pro Bed Tailgate Net . For further information on installation, please see the fitment instructions in the INSTALL tab. Features PBDR001T - RAM 1500 (5th Gen) 4 Door Crew Cab 5'7" Box (2019-Current) Pro Bed Rack Kit Consisting of: 3x FASS025 - Foot Set / 70mm - 80mm 1x PBDR001S - RAM 1500 (5th Gen) 4 Door Crew Cab 5'7" Box Pro Bed 3x RRAC921 - Canopy Rack Kit Installation Set 1x RRSTJ08 - SLII Tray - 1425mm(W)X1560mm(L) Material Used: Black epoxy powder - coated T6 aluminium Approximate Installed Weight: 78.46kg (172.97lbs) Shipping Dimensions: Width: 445mm (18") Length: 1720mm (68") Height: 760mm (30") Shipping Weight: Weight: 85kg (187lbs)

Effortlessly increase your Ram 1500 Cab's gear-carrying capabilities with the 752mm/29.6" long Slimline II Roof Rack Kit. This off-road proven rack requires drilling to install. You now have the perfect platform to secure firewood, a Wolf Pack Pro, recovery tracks, or other equipment. Compatible with cab over campers. This 752mm/29.6" long, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Ram 1500 Quad Cab. Also suitable for crew cab with over cab camper and 2500 / 3500 single cabs. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. All Front Runner Racks are backed by a Limited Lifetime Warranty* For further information on installation, please see the fitment instructions in the INSTALL tab. Suitable for:Full Size Slimline II for Ram 1500 Regular CabCab Over Camper Slimline II for RAM 1500 Quad CabCab Over Camper Slimline II for RAM 1500 Crew Cab Note:Both traditional and panoramic sunroofs may be operated in 'vent mode' Only traditional sunroof can fully open, Panoramic can not fully open as it opens to the outside.Models with traditional sunroofs include: Ram 1500 (2009-2018), Ram 1500 Classic (2019-Current), Ram 2500/3500 (2019-Current).Models with panoramic sunroofs include: Ram 1500 (2019-Current). Features KRDR023T - Ram 1500 Quad Cab (2019-Current) Slimline II Roof Rack Kit Consisting of: 1x FADR005 - Ram 1500 Quad Cab(2019-Curr)Camper Rail 1x RRSTJ04 - SLII Tray - 1425mm(W)X752mm(L) Material Used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 17.08kg (37.65lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle's roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1720mm (68") Height: 265mm (10") Shipping Weight: Weight: 22kg (48lbs)

This Shower Cubicle secures to your Front Runner rack using two mounting brackets. The stainless steel cubicle frame slides into the two mounting brackets. Easily slide the 240gsm, UV protected shower curtain over the tubing frame to create a private enclosure. Use guy ropes to secure the corners of the curtain in place. Stores away neatly in the supplied carry bag. Features Consists of: 1 x Shower Curtain 4 x Ground Pegs 4 x Guy Ropes 1 x Storage Bag Installation Hardware Fitting Instructions Materials used: Black powder coated 304 stainless steel Black powder coated steel 240gsm Ripstop, UV and mold resistant fabric Product Dimensions: 1004mm (39.5") L x 1065mm (41.9") W x 1700mm (66.9") H Weight: 2.9kg (6.3lbs)

  A bracket set that attaches to the side profile of your Slimline II or Slimpro Van Roof Rack. Adjustable to suit all vehicle types and load beds. Mounts your Rack Ladder to these brackets to access the roof of your vehicle. These brackets can be left on your rack without being obtrusive. Made from high-grade steel and powder coated with the same durable all-weather epoxy powder coating as the Front Runner racks. Features Consists of: 1 x Pair of Ladder Side Mount Brackets Installation Hardware Fitting Instructions Materials used: Black powder coated high strength steel Product Dimensions: 182mm (7.2") L x 87mm (3.4") W x 397mm (15.6") H Weight: 3kg(6.6lbs)

A 6 (six) step ladder to easily access your gear. Supplied in 2 pieces for easy storage. Made from sturdy aluminum and anodized black to match the Front Runner Rack. Foot-friendly steps. To secure your Rack Ladder firmly in place, add the Rack Ladder Side Mount Bracket *sold separately. Holds a maximum weight of 180kg/400lbs. Features Consists of: 1 x Rack Ladder Fitting Instructions Materials used: Black powder coated aluminium Product Dimensions: In-Use Dimensions: 359mm (14.1") W x 50mm (2") D x 2200mm (86.6") H Storage Dimensions: 359mm (14.1") W x 100mm (3.9") D x 1205mm (47.4") H Weight: 5.33kg (11.8lbs)

These adaptor plates give you the ability to attach 2 Thule slotted Load Bars or Aero Bars to a Front Runner Slimline II Roof Rack. If you currently own Thule Accessories and would like to use them with a Front Runner Slimline II Roof Rack, you can use your Thule load bars or Aero Bars to mount your accessories (e.g. Bike Mounts or Kayak mounts) to the rack. Works with both the SLOTTED-SQUARE and AERO Thule Load Bars. This adapter plate DOES NOT work with the Thule rectangular load bars that do not have slots (ie. the basic Thule load bar found in the USA.) Steel. Black powder coated. Mounts onto individual slats via the T-slot system. T-slot bolts included. Pre-cut fitment holes. Features Works with: Both the SLOTTED SQUARE and AERO Thule Load Bars. Materials used: 2.5mm (0.098") high strength steel, supplied with mountings for Aero and Square Bar Consists of: 4 x Thule Load Bar adaptors and a nuts and bolts kit Product Dimensions: L 290mm (11.42") x W 74mm (2.91") x H 27mm (1.06") Weight: 2kg (4.4lbs)

Once these brackets are installed on a Front Runner Rack, no additional tools are needed to remove or refit the awning. Simply release the 2 latches and lift the awning away in seconds. No more wrenching in tight spaces during the off-season or time-consuming weekday removal of the awning. This strong and "rattle-free" mounting system is built off-road tough for use with Front Runner Racks. Works with all Front Runner Awnings and other popular awning brands like Eezi-Awn, Oz Tent, etc. 2 low profile base brackets are bolted to a Front Runner Rack while 2 self-aligning bushes are secured to the awnings mounting channel using the supplied fasteners. Safely secured in place using 2 latches with built-in safety catch. For added peace of mind, lock your latches in place using Rack Accessory Lock / Small. The brackets are small, unobtrusive and can be left on the roof rack when the awning is not mounted. No awning modification required. Removed awnings can be stored using the wall mount brackets supplied. Supplied with all required mounting hardware. Fitting instructions are included. Weight limit: 20kg (44.1lbs). Note: Not suitable for 270 degree awnings. Features Consists of: 1 x Pair of Quick Release Awning Brackets Installation Hardware Fitting instructions Materials used: Black powder coated Steel Product Dimensions: (Per Single Bracket) 161.5mm(6.4") L x 103mm (4.1") W x 100mm (3.9") H Weight: 2kg (4.4lbs)

Designed to mount bikes with 100/110mm x 12mm, 100/110mm x 15mm, and 110/110mm x 20mm thru-axles (Boost) Compatible with pinch style forks such as Fox40, Manitou Dorado and Marzocchi 380 Rear wheel holder can accommodate all wheel sizes and widths from 700c x 23mm road wheels up to 26 x 4.5" fat bike tires. Rear wheel holder features a ratchet buckle and strap that allows fast adjustment Works with Front Runner Racks and Load Bars Made from steel and aluminum and powder-coated for durability and longevity Note: Installation requires a minimum rack length of 1156mm (six slats). Features Consists of: 1 x Front Fork Mount 1 x Rear Wheel Mount 1 x Pair of inserts for 12mm 100/110 Thru Axle 1 x Pair of Inserts for 15mm 100/110 Thru Axle 1 x Pair of inserts for 20mm 100/110 Thru Axle Installation Hardware Fitting Instructions Materials used: Black powder coated steel Black powder coated aluminum Product Dimensions: 300mm (11.8") L x 176mm (6.9") W x 81mm (3.2") H Weight: 1.5kg (3.3lbs)

Made of stainless steel and sealed with the same durable, weather rated powder coating as the Front Runner Slimline Roof Racks. The ultra dense yet soft weather resistant rubber pads cradle your valuable gear without harming or scratching the surfaces. The Stratchit straps clever cinching system mean easy-on and easy-off secure transport every time. Adjustable to hold all shapes and lengths of boards across the width and length of Front Runner Slimline Roof Racks or Front Runner Load Bars. Each Front Runner Board Carrier can hold 1 to 2 boards. Most Front Runner Roof Racks and Load Bar widths will accommodate a 2nd Front Runner Board Carrier to hold up to 4 boards. Includes: 2 pairs of board holders 1 pair of Front Runner Stratchits All hardware necessary to mount to a Slimline Roof Rack, Load Bars, or other flat surface. Installation Manual Made in South Africa Features Consists of: 2x Brackets 2x Stratchit Strap Bolt Kit Materials used: Black powder-coated Steel Polyethylene pads Product dimensions: L 276mm (10.9") x W 76mm (3") x H 67mm (2.6") Weight: Individual bracket: 0.6kg (1.3lbs) Entire kit: 2.9kg (6.4lbs)

These brackets have been designed to work in conjunction with the Pro Stainless Steel Camp Table, the Pro Stainless Steel Prep Table and Under-Rack Table Latch - by Front Runner to make taking a sturdy table along with you on your travels as simple and effortless as possible. Pro Stainless Steel Table Under Rack Bracket - by Front Runner: A no-noise and secure storage solution designed specifically for the Pro Stainless Steel Camp/Prep Table or Pro Stainless Steel Prep Table with Basin - by Front Runner. The brackets can be mounted both parallel and perpendicular to the roof rack's slats giving the option to access to the table from either the side or rear of the vehicle. Easy installation. Made of steel that is black powder coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack. Under-Rack Table Slides Latch - by Front Runner: Keeps the Pro Stainless Steel Camp/Prep Table or Pro Stainless Steel Prep Table with Basin - by Front Runner securely stored in the Under-Rack Table Brackets - by Front Runner. Secured to the top of the Slimline II rack using the T-slot and clamps over the lip of the table to keep it in place. A rubber insert prevents rattling and damage to the table. Spring loaded for ease of use. Lockable for added security. Made of steel that is black powder coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack. NOTE: A min clearance of 65mm (2.5") between the underside of the rack and the crown of the roof is required for fitment of a Front Runner Table Kit. Features Consists of: 1 x Pair of Storage Slides 1 x Table Latch Installation Hardware Materials used: Black powder-coated Steel PVC Grommet Product Dimensions: 881mm (34.7")L x 187mm (7.4")W x 46mm (1.8")H Weight: 2.4kg (5.3lbs) TABLE CARE: Keep your table clean and sparkling with these easy care instructions. Add a small amount of dish soap to a damp soft cloth. Wipe the table along the grain of your tabletop. Dry excess moisture with a dry towel. Quickly add polish by dabbing on a small amount of mineral or baby oil, wiping with the grain of the stainless steel. Done!

This lightweight, sturdy prep-sized camp table is ideal for food preparation, food serving, and gathering around to eat. Features include a stainless steel top and black powder-coated aluminum frame. Specifically designed to be easily stored UNDERNEATH most Front Runner Slimline II Roof Racks.*The Pro Stainless Steel Prep Table Kit includes the Pro Stainless Steel Prep Table, Under-Rack Table Slides and Under-Rack Table Slides Latch. A complete prep table and table storing solution. Effortlessly take a previously cumbersome luxury item on any vehicle based adventure.   Pro Stainless Steel Prep Table - by Front Runner: The extruded aluminum frame nests into the storage brackets and is secured with the table latch eliminating any excessive noise. A durable stainless steel table top ensures a hygienic surface for the preparation and serving of meals. The table frame and legs are powder-coated black with the same durable, corrosion resistant coating as the Front Runner Slimline II Roof Rack. The Legs easily unfold and with the open-and-lock mechanism are kept firmly in place. Rounded glass filled nylon corners prevent any accidental knicks or damage and provide a grip point when removing the table from under your roof rack.   Under-Rack Table Brackets - by Front Runner: A no-noise and secure storage solution designed specifically for the Pro Stainless Steel Prep Table. The brackets can be mounted both parallel and perpendicular to the roof rack's slats giving the options to access to the table from the side or rear of the vehicle. Easy installation. Made of steel and is black powder-coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack.   Under-Rack Table Slides Latch - by Front Runner: Keeps the Pro Stainless Steel Prep Table securely stored in the Under-Rack Table Brackets - by Front Runner. Secured to the top of the Slimline II roof rack using the T-slot and clamps over the lip of the table to keep it in place. A rubber insert prevents rattling and damage to the table. Spring loaded for ease of use. Lockable for added security. Made of steel and is black powder-coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack. NOTE: Table fitment requires 65mm (2.5") clearance from under the rack to highest point of the roof.Side mounting requires 4 open slatsRear mounting requires 7 open slats and is not suitable for vehicles with rear roof antennaStill unsure? Contact the Front Runner Help Center WARNING Cancer or Reproductive Harm www.P65Warnings.ca.gov Consists of:1 x Table1 x Storage Slides1 x LatchTable:Materials used:Black powder-coated aluminumSteelProduct Dimensions:1130mm (44.5") L x 550mm (21.7") W x 35mm (1.4") HHeight when opened: 734mm (28.9") HWeight:10.03kg (22.1lbs)Table Slide:Materials used:Black powder-coated SteelProduct Dimensions:881mm (34.7") L x 187mm (7.4") W x 46mm (1.8") HWeight:2.4kg (5.3lbs)Table Latch:Materials used:Black powder-coated SteelPVC GrommetProduct Dimensions:91mm (3.6") L x 51.7mm (2") W x 47mm (1.9") HWeight:191g (6.7oz)Full Kit Dimensions:1165mm (45.9") L x 642mm (25.3") W x 109mm (4.3") HFull Kit Weight:12.6 Kg (27.8lbs) TABLE CARE: Keep your table clean and sparkling with these easy care instructions. Add a small amount of dish soap to a damp soft cloth.Wipe the table along the grain of your tabletop.Dry excess moisture with a dry towel.Quickly add polish by dabbing on a small amount of mineral orbaby oil, wiping with the grain of the stainless steel.  

An ideal solution for meals, food preparation, and gear staging while traveling. Aluminum locking legs. Sturdy and lightweight. Operational height 734mm (28.9") Hygienic, easy to clean stainless steel top -- just like the pros use in restaurants around the world. The table frame and legs are finished with the same durable, corrosion resistant black powder coating as the Front Runner Slimline II Roof Rack. Rounded glass filled nylon corners prevent accidental nicks or damage. Ultra slim and can be mounted securely for rattle free transport underneath most Front Runner Slimline II Roof Racks using the Pro Stainless Steel Table Under Rack Bracket* *For details on fitment see below. * WILL A FRONT RUNNER TABLE FIT UNDER MY SLIMLINE II ROOF RACK? There are 2 factors to consider: Is the roof rack TALL ENOUGH? All Roof Rack kits with a designated TALL mounting option have room to fit a table underneath. If your Slimline II Roof Rack uses a Front Runner Foot Rail mounting system, a table will also fit underneath. Many other Front Runner Roof Rack kits have enough height to mount a table underneath, but please keep in mind, we recommend 65mm/2.5 of clearance between the bottom of the roof rack and the highest point of the roof. Is the roof rack LONG ENOUGH? For REAR MOUNT installation, the table requires a Slimline II Roof Rack that is 1358mm or longer (7 slats). Please check the SPECS tab on any Slimline II Roof Rack for exact measurements of the rack tray. For a SIDE MOUNT installation, the table requires a 3 slat opening (the space between feet/legs). All Front Runner Foot Rail mounting systems have an opening that fits all widths of tables. NOTE: A min clearance of 65mm (2.5") between the underside of the rack and the crown of the roof is required for fitment of a Front Runner Table Kit. If youre still not sure if your rack will work with a table underneath, please contact us. Features Consists of: 1 x Table Materials used: Black powder-coated aluminum Stainless steel Product Dimensions: 1130mm (44.5") L x 550mm (21.7") W x 35mm (1.4") H Height when opened: 734mm (28.9") H Weight: 10.03kg (22.1lbs) TABLE CARE: Keep your table clean and sparkling with these easy care instructions. Add a small amount of dish soap to a damp soft cloth. Wipe the table along the grain of your tabletop. Dry excess moisture with a dry towel. Quickly add polish by dabbing on a small amount of mineral or baby oil, wiping with the grain of the stainless steel. Done!

A complete camp table and table storing solution. Effortlessly take a previously cumbersome luxury item on any vehicle based adventure. Pro Stainless Steel Camp Table - by Front Runner: The extruded aluminum frame nests into the storage brackets and is secured with the table latch eliminating any excessive noise. A durable stainless steel table top ensures a hygienic surface for the preparation and serving of meals. The table frame and legs are powder-coated black with the same durable, corrosion resistant coating as the Front Runner Slimline II Roof Rack. The Legs easily unfold and with the open-and-lock mechanism are kept firmly in place. Rounded glass filled nylon corners prevent any accidental knicks or damage and provide a grip point when removing the table from under your roof rack. Under-Rack Table Brackets - by Front Runner: A no-noise and secure storage solution designed specifically for the Pro Stainless Steel Camp Table. The brackets can be mounted both parallel and perpendicular to the roof rack's slats giving the options to access to the table from the side or rear of the vehicle. Easy installation. Made of steel and is black powder-coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack. Under-Rack Table Slides Latch - by Front Runner: Keeps the Pro Stainless Steel Camp Table securely stored in the Under-Rack Table Brackets - by Front Runner. Secured to the top of the Slimline II roof rack using the T-slot and clamps over the lip of the table to keep it in place. A rubber insert prevents rattling and damage to the table. Spring loaded for ease of use. Lockable for added security. Made of steel and is black powder-coated in the same durable and corrosion resistant coating as the Front Runner Slimline II roof rack. NOTE: Table fitment requires 65mm (2.5") clearance from under the rack to highest point of the roof. Side mounting requires 5 open slats Rear mounting not suitable for vehicles with rear roof antenna Still unsure? Contact the Front Runner Help Center Features Consists of: 1 x Table 1 x Storage Slides 1 x Latch Table: Materials used: Black powder coated Aluminium Steel Product Dimensions: 750mm (29.5") W x 1130mm (44.5") L x 32mm (1.3") H Height when opened: 730mm (28.7") Weight: 11.82kg (26.1lbs) Table Slide: Materials used: Black powder coated Steel Product Dimensions: 881mm (34.7") L x 187mm (7.4") W x 46mm (1.8") H Weight: 2.4kg (5.3lbs) Table Latch: Materials used: Black powder coated Steel PVC Grommet Product Dimensions: 91mm (3.6") L x 51.7mm (2") W x 47mm (1.9") H Weight: 191g (6.7oz) Full Kit Dimensions: 1130mm (44.5") L x 775mm (30.5") W x 55mm (2.2") H Full Kit Weight: 15.2kg (33.5lbs)   TABLE CARE: Keep your table clean and sparkling with these easy care instructions. Add a small amount of dish soap to a damp soft cloth. Wipe the table along the grain of your tabletop. Dry excess moisture with a dry towel. Quickly add polish by dabbing on a small amount of mineral or baby oil, wiping with the grain of the stainless steel. Done!

An ideal solution for meals, food preparation, and gear staging while traveling. Aluminum locking legs. Sturdy and lightweight. Operational height 730mm (28.7") Hygienic, easy to clean stainless steel top -- just like the pros use in restaurants around the world. The table frame and legs are finished with the same durable, corrosion resistant black powder coating as the Front Runner Slimline II Roof Rack. Rounded glass filled nylon corners prevent accidental nicks or damage. Ultra slim and can be mounted securely for rattle free transport underneath most Front Runner Slimline II Roof Racks using the Pro Stainless Steel Table Under Rack Bracket* *For details on fitment see below. * WILL A FRONT RUNNER TABLE FIT UNDER MY SLIMLINE II ROOF RACK? There are 2 factors to consider: Is the roof rack TALL ENOUGH? All Roof Rack kits with a designated TALL mounting option have room to fit a table underneath. If your Slimline II Roof Rack uses a Front Runner Foot Rail mounting system, a table will also fit underneath. Many other Front Runner Roof Rack kits have enough height to mount a table underneath, but please keep in mind, we recommend 65mm/2.5 of clearance between the bottom of the roof rack and the highest point of the roof. Is the roof rack LONG ENOUGH? For REAR MOUNT installation, the table requires a Slimline II Roof Rack that is 1358mm or longer (7 slats). Please check the SPECS tab on any Slimline II Roof Rack for exact measurements of the rack tray. For a SIDE MOUNT installation, the table requires a 5 slat opening (the space between feet/legs). All Front Runner Foot Rail mounting systems have an opening that fits all widths of tables. NOTE: A min clearance of 65mm (2.5") between the underside of the rack and the crown of the roof is required for fitment of a Front Runner Table Kit. If youre still not sure if your rack will work with a table underneath, please contact us.

Upright bike carrier, made from strong steel and aluminum. Powder-coated in the same durable finish as the Front Runner rack and load bars for durability. Front fork clamp features a quick release that fits all standard fork dropouts. Rear wheel holder can accommodate all wheel sizes and widths from 700c x 23mm road wheels up to 26 x 4.5" fat bike tires. Quickly secure and adjust the rear wheel with the robust ratcheting buckle and strap. Note: Fitment to a rack requires a minimum rack length of 1156mm (6 slats). Note: This solution is not compatible with Boost Hubs/Forks. Features Consists of: 1 x Fork Clamp 1 x Rear Wheel Holder Installation Hardware Fitting Instructions Materials used: Black powder coated steel & aluminum Rubber ladder strap Plastic ratchet buckle Overall Product Dimensions: 300mm (11.8") L x 176mm (6.9") W x 81mm (3.2") H Rear Holder: 230mm (9.1") L x 176mm (6.9") W x 81mm (3.2") H Front Clamp: 70mm (2.8") L x 152mm (6") W x 114mm (4.5") H Weight: 1.6kg (3.5lbs)

Fits most size canoes, kayaks, SUPs and surf skis. The space between the brackets is only limited by the length of your Front Runner Roof Rack or distance between your Load Bars. Highly adjustable brackets allow for multiple mounting angles for your canoe, kayak or SUP. The foam-padded holders are self-adjusting for the perfect fit to the hull of your boat. The dense weather-resistant open cell foam pads are covered with a water-repellent polyester cover that is UV stabilized to prevent fading. Pads can be easily replaced if damaged in any way. Toys are secured to the Canoe / Kayak / SUP Carrier using the supplied Front Runner Stratchits straps and eye nuts. The included Front Runner adjustable and stretchable Stratchits are the perfect tie-down for serious cargo. The quick and efficient straps will keep loads stable and secure without damaging surfaces and are rated up to 300 lbs. The Stratchit's clever cinching system creates an easy-on, and easy-off, secure transport every time. Complete kit includes everything necessary to secure your water toys to Front Runner Roof Racks or Load Bars. Weight limit: 60kg (132 lbs). Features Consists of: 2 x Adjustable Holders 4 x Pads 1 x Pair of Stratchits 4 x Eye nuts Installation Hardware Fitting Instructions Materials used: Adjustable Holders: Black powder coated steel EPE (Expandable Polyethylene) foam Pads: 100% UV protected polyester outer shell 100% polyester lining Product Dimensions (fully opened): 700mm (27.6") L x 75mm (3") W x 112mm (4.4") H (Single Holder) Weight: 6.2kg (13.7lbs) (Holder Set)

Easily install onto your Front Runner Rack in minutes. No front wheel removal necessary. Suitable for all bike sizes; all frame styles including composite carbon frames; all thru axle and brake configurations as well as Lefty forks and full suspension bikes. Front wheel holder is easily adjusted and holds the bike steady while the rear Wheel Holder is secured. Adjustable to secure most wheel diameters including road bikes, MTB and fat bikes with tire widths ranging from 18mm/0.7" up to 132mm/5.2". The carrier folds flat and secures onto your rack when not in use. Bike can be locked using Rack Accessory Lock / Large. Constructed with same weather resistant stainless steel and powder coating as the Front Runner racks and mounting systems. Features Consists of: 1 x Bike Carrier 1 x Bike Carrier Rack Clamp 1 x Rear Wheel Holder Installation Hardware Fitting Instructions Materials used: Black powder coated steel Plastic Product Dimensions: Bike Carrier (Closed): 825mm (32.5") L x 205mm (8.1") W x 100mm (3.9") H Rear Wheel Holder: 230mm (9.1") L x 170mm (6.7") W x 70mm (2.8") H Weight: 9.4kg(20.7lbs) Special Notes: Suitable for all bike sizes incl. Fat Bikes

Water must be easily accessible when on the road in your rig. That is exactly what the lockable Pro Bed Water Kit offers, as it attaches to the side of your Pro Bed System, 20 litres of water at your disposal. This Pro Bed Water Kit / 20L bolts on the side of the Pro Bed System. Install this mount onto your Pro Bed System to allow quick and easy access to your 20L Pro Water Tank. Easily remove your water tank by loosening the stainless-steel eye nuts. The water tank can be locked for added peace of mind using the Rack Accessory Lock / Small (sold separately). Plastic alignment spacers protect, align and secure your water tank. Mounting holes could be used mount other accessories to your Pro Bed System or Pro Bed Rack Kit. As a recovery solution, the Pro Bed Recovery Bracket is available. Made of high strength steel and coated in the same durable, weather-resistant black powder coating as the Front Runner Rack. Features Consists of: 1 x Pro Bed Universal Accessory Mount 1 x Universal Side Mount for Pro Water Tank / 20L 1 x Pro Water Tank With Tap / 20L Installation Hardware Fitment Guide Materials used: Black powder coated steel Food grade BPA free polyethylene Water Tank Assembled Product Dimensions: 470mm (18.5") L x 224mm (8.8") W x 490mm (19.3") H Weight: 6.82kg (15lbs)

When stuck, you want quick access to your recovery boards. This is exactly what the Pro Bed Recovery Bracket offers, allowing you to conveniently attach your MAXTRAX, Tred Pro or Tred GT to the Pro Bed System. This Pro Bed Recovery Bracket bolts on the top and bottom side of the Pro Bed System. To attach your MAXTRAX, use the included Pro Bed Recovery Device Mounting Hardware or MAXTRAX Mounting Pin Set * Sold Separately. The included Pro Bed Recovery Device Mounting Hardware can be used to mount your Tred Pro and Tred GT Recovery Boards. Mounting holes could be used mount other accessories to your Pro Bed System or Pro Bed Rack Kit. As a universal solution, the Pro Bed Universal Accessory Mount is available. For a complete water solution, Front Runner offers the Pro Bed Water Kit / 20L. Made of high strength steel and coated in the same durable, weather-resistant black powder coating as the Front Runner Rack. Features Consists of: 1 x Pro Bed Universal Accessory Mount 1 x Pro Bed Recovery Device Mounting Hardware Installation Hardware Fitment Guide Materials used: Black powder coated steel Product Dimensions: 490mm (19.3") L x 200mm (7.9") W x 30mm (1.9") H (Per Single Bracket) Weight: 3.28kg (7.2lbs)

Add this strong, steel Side Molle Panel to make your Pro Bed Rack even more versatile. This 1400mm/55.1" long, Molle Panel easily slides into the side extrusions to create that extra storage space we all need. A great place to put gear you might need in a hurry. This Pro Bed Rack Side Molle Panel creates even more storage space to attach various accessories to the outside of the bed rack for easy access. It fits onto the sides of the Pro Bed Rack by sliding into the side extrusions. No drilling is required. Made of high-strength steel and sealed in the same durable black powder coating as the Front Runner rack. Features Consists of: 4 x Molle Panel Installation Hardware Fitting Instructions Materials used: Black powder coated steel Product Dimensions: 1400mm (55.12") L x 30mm (1.18") W x 496mm (19.53") H Weight: 9.2kg (20.3lbs)

Create deliciously hearty meals out in the wilderness, fit for the avid explorer and overlanding veterans alike. The Front Runner Potjie Pot/Dutch Oven Carrier is a safe and durable means of transporting your potjie pot/dutch oven where ever your travels may take you. The potjie pot/dutch oven is placed centrally into the bracket with the three legs fitting into the holes in the three protrusions extending from the centre of the bracket. The supplied ratchet strap threads through the lid of the pot and fixes to pre-drilled points on the bracket. Made of corrosion resistant steel and black powder-coated with an industry preferred, outdoor rated coating. Features Consists of: Potjie bracket for No 2 & No 3 pot Ratchet strap Mounting hardware Materials used: Black powder-coated steel Product Dimensions: 276mm (10.9") L x 229mm (9") W x 133mm (5.2") H Weight: 2kg (4.4lbs)

Theres no better place to keep potentially hot, grimy, dirty, and cumbersome camp kitchen supplies than up and out of the way, outside the vehicle. The Front Runner Potjie Pot Carrier offers a sensible way to travel with a potjie pot. The potjie pot is secured in the bracket by the three legs. The supplied ratchet strap threads through the lid of the pot and fixes points on the bracket. The #3 cast iron pot holds 7.8L / 2.1 Gallons. The round shape and cast iron allows the heat to flow evenly around the sides and maintain liquids at the lowest point to keep them from burning. The lid has a deep lip for holding hot coals. The high strength steel carrier is finished with the same durable, weather resistant powder coating as the Front Runner Slimline II Rack. Like all Front Runner rack accessories, the installation is simple. Just slide the bolts into the t-slots of any Front Runner Rack Tray, set down the carrier, then add nuts and tighten. Features Consists of: Rack mounted bracket Strap guide Ratchet strap mounting hardware No 3 cast iron pot Materials used: Black powder-coated high strength steel Nylon strap Cast iron pot Product Dimensions: 280mm (11") W x 280mm (11") D x 343mm (13.5") H Pot Specifications: No. 3 potjie Pot - 7.8l (2.1gal) capacity Max outer diameter: 290mm (11.4") Height: 300mm (11.8") Lid max outer diameter: 260mm (10.2") Total Weight: 11.25kg (24.9lbs)

This 1358mm/53.5" long full-size Slimline II cargo carrying roof rack kit for the Porsche Cayenne contains Slimline II Tray, Wind Deflector and 4 Feet. Installs easily to factory/OEM tracks with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRPC001T - Porsche Cayenne (2002-2010) Slimline II Roof Rack Kit - by Front Runner Consisting of: 2 x FASS013 - Foot Set / 60mm-70mm - by Front Runner 2 x RRAC907 - Stud Plate MB Sprinter Track 1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 22.8kg (50.3lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18.0") Length: 1615mm (64.0") Height: 140mm (6.0") Shipping Weight: 25.3kg (56.0lbs)

This 954mm/37.6" long, full-size, Slimline II cargo carrying roof rack kit for the Porsche 924 contains the Slimline II Tray and Wind Deflector, as well as 4 Gutter Mount Legs for mounting the Tray to the vehicle. Installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: This Kit requires the vehicle to have protruding side gutters to be fitted. If unsure of fitment, please contact Front Runner Support. Features KRPN001T - Porsche 924 Slimline II Roof Rack Kit - by Front Runner Consisting of: 2x LASD102 - No 2 Leg Diagonal 130mm (Pair)2x RRAC034 - Inter-Slat Bracket1x RRSTA05 - SLII Tray - 1165mm(W)X954mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 22.54kg (49.69lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 260mm (10")   Shipping Weight: Weight: 43.4kg (95lbs)

The powerful Porsche 911 has little gear-carrying carrying capacity unless you fit Front Runner's modular Slimline II Roof Rack Kit. The Wind Deflector will help to minimize rack noise, while the tray is the perfect place to put extra cargo, your spare wheel or other gear.   This 954mm/37.6" long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 4 Foot Rails to mount the Slimline II Tray to your Porsche 911. It easily installs using the existing factory mounting points. No drilling required.All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRPN002T - Porsche 911 (997 Model) Slimline II Roof Rack Kit Consisting of: 1x FAPN001 - Porsche 911(997 Model) Mounting Bracket 1x RRSTA05 - SLII Tray - 1165mm(W)X954mm(L) Material Used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 16.8kg (37.04lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicle's roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1720mm (68") Height: 290mm (11") Shipping Weight: Weight: 23kg (51lbs)

This kit creates a full-size rack that sits above your Polaris Ranger load bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1345mm x 752mm) and 4 Pickup Truck Bed Universal Legs that fit into the Load Bed Mount. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRPR002T - Polaris Ranger Slimline II Load Bed Rack Kit Consisting of: 2x LASS028 - Pick-Up Roll Top Leg Mount 1x LASS043 - Polaris Ranger Load Bed Mount 1x RRSTG04 - SLII Tray - 1345mm(W)X752mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 24.9kg (54.9lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1720mm (68") Height: 265mm (10") Shipping Weight: Weight: 31kg (68lbs)

This Slimsport Kit is suited for truck canopies/camper shells/caps. This low profile flat deck Slimsport rack has a load carrying area of 1350mm (53.1") x 1211mm (47.7"). The sleek side rails have integrated mounting feet. Mounting feet also have additional brace brackets for added strength. The high-strength aluminum slats have top and bottom T-slots suitable for all Front Runner top mount accessories. Easily add on the Rack Accessory Mounting Bracket Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner (sold separately) for all Front Runner side mount accessories. Fitment guide and all mounting hardware included. Note: Drilling required. Note: Under Rack Tables are not compatible with the Slimsport rack kit range Features KSCA001 - Pickup Load Bed 5.5'Canopy/Cap/Trailer Slimsport Rack Kit Consisting of: 1 x Pickup Load Bed 5.5'Canopy/Cap/Trailer Slimsport Tray 1 x Installation Hardware 1 x Fitting Instructions Material used: Black epoxy powder - coated T6 aluminium High strength steel Assembled Rack Kit Dimensions: 1350mm (53.1") L x 1211mm (47.7") W x 63mm (2.5") H Approximate Installed Weight: 16.99kg (37.46lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof. Shipping Dimensions: Width: 240mm (9") Length: 1560mm (61") Height: 100mm (4") Shipping Weight: Weight: 17.17kg (38lbs)

This kit creates a full-size rack that sits above your Pickup's load bed when fitted with a EGR RollTrac cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1425mm x 1358mm) and 6 Pickup Roll Top Leg Mounts that fit into the existing EGR RollTrac channels. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: This rack kit is not suitable for the Volkswagen Amarok. If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRRT033T - Pickup EGR RollTrac Slimline II Load Bed Rack Kit / 1425(W) x 1358(L) - by Front Runner Consisting of: 3x LASS028 - Pick-Up Roll Top Leg Mount 1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 29.29kg (64.57lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1730mm (68") Height: 195mm (8") Shipping Weight: Weight: 28kg (62lbs)

Compatible with Peugeot Boxer (L4H2/159" WB) (2014-Current) high roof vans with a vehicle length of 6363mm / 250.5". Load-carrying area: 3928mm (154.6") x 1565mm (61.6"). Ten (10) Mounting Feet secure into van's existing factory mounting points. Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5"). Compatible with most Front Runner accessories. Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories. Fitment guide and all mounting hardware are included. No drilling or modification required. All Front Runner racks are backed by a limited lifetime warranty.* Features KVPB005T - Peugeot Boxer (L4H2/159" WB/High Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner Consisting of: 5x FAVF002 - FPCR Foot Set - by Front Runner 2x RRAC207 - Van Rack Joiner Kit 2x RRAC208 - Van Rack Side Profile End Caps 5x RRNS1475 - Narrow Slat / 1475mm (Pair) 1x SPVT001 - Van Rack Side Profile / 1156mm 2x SPVT002 - Van Rack Side Profile / 1358mm 1x WDST013 - Wind Deflector Van Rack 30mm Lip Material used: Black epoxy powder - coated T6 aluminium High strength steel Assembled Rack Kit Dimensions: 3928mm (154.6") L x 1565mm (61.6") W x 127mm (5") H Approximate Installed Weight: 42.17kg (92.97lbs) Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom. Shipping Dimensions: Width: 300mm (12") Length: 1805mm (71") Height: 195mm (8") Shipping Weight: Weight: 43.35kg (95lbs)

Compatible with Peugeot Boxer (L2H1/136" WB) 2014-Current low roof vans with a vehicle length of 5413mm / 213.1". Load-carrying area: 2974mm (117.1") x 1565mm (61.6"). Six (6) Mounting Feet secure into van's existing factory mounting points. Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5"). Compatible with most Front Runner accessories. Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories. Fitment guide and all mounting hardware are included. No drilling or modification required. All Front Runner racks are backed by a limited lifetime warranty.* Features KVPB002T - Peugeot Boxer (L2H1/136" WB/Low Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner Consisting of: 3x FAVF002 - FPCR Foot Set - by Front Runner 1x RRAC207 - Van Rack Joiner Kit 2x RRAC208 - Van Rack Side Profile End Caps 4x RRNS1475 - Narrow Slat / 1475mm (Pair) 1x SPVT002 - Van Rack Side Profile / 1358mm 1x SPVT003 - Van Rack Side Profile / 1560mm 1x WDST013 - Wind Deflector Van Rack 30mm Lip Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 31.49kg (69.42lbs) Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom. Shipping Dimensions: Width: 300mm (12") Length: 1805mm (71") Height: 195mm (8") Shipping Weight: Weight: 37.35kg (82lbs)

Compatible with Peugeot Boxer (L2H2/136" WB) (2014-Current) High roof vans with a vehicle length of 5413mm / 213.1". Load-carrying area: 2974mm (117.1") x 1565mm (61.6"). Six (6) Mounting Feet secure into van's existing factory mounting points. Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5"). Compatible with most Front Runner accessories. Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories. Fitment guide and all mounting hardware are included. No drilling or modification required. All Front Runner racks are backed by a limited lifetime warranty.* Features KVPB003T - Peugeot Boxer (L2H2/136" WB/High Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner Consisting of: 3x FAVF002 - FPCR Foot Set - by Front Runner 1x RRAC207 - Van Rack Joiner Kit 2x RRAC208 - Van Rack Side Profile End Caps 4x RRNS1475 - Narrow Slat / 1475mm (Pair) 1x SPVT002 - Van Rack Side Profile / 1358mm 1x SPVT003 - Van Rack Side Profile / 1560mm 1x WDST013 - Wind Deflector Van Rack 30mm Lip Material used: Black epoxy powder - coated T6 aluminium High strength steel Assembled Rack Kit Dimensions: 2974mm (117.1") L x 1565mm (61.6") W x 127mm (5") H Approximate Installed Weight: 31.49kg (69.42lbs) Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom. Shipping Dimensions: Width: 300mm (12") Length: 1805mm (71") Height: 195mm (8") Shipping Weight: Weight: 37.35kg (82lbs)

Compatible with Peugeot Boxer (L1H1/118" WB) (2014-Current) low roof vans with a vehicle length of 4963mm / 195.4". Load-carrying area: 2570mm (101.2") x 1565mm (61.6"). Six (6) Mounting Feet secure into van's existing factory mounting points. Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5"). Compatible with most Front Runner side mount accessories. Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories. Fitment guide and all mounting hardware are included. No drilling or modification required. All Front Runner racks are backed by a limited lifetime warranty.* Features KVPB001T - Peugeot Boxer (L1H1/118" WB/Low Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner Consisting of: 3x FAVF002 - FPCR Foot Set - by Front Runner 1x RRAC207 - Van Rack Joiner Kit 2x RRAC208 - Van Rack Side Profile End Caps 4x RRNS1475 - Narrow Slat / 1475mm (Pair) 1x SPVT001 - Van Rack Side Profile / 1156mm 1x SPVT002 - Van Rack Side Profile / 1358mm 1x WDST013 - Wind Deflector Van Rack 30mm Lip Material used: Black epoxy powder - coated T6 aluminium High strength steel Assembled Rack Kit Dimensions: 2570mm (101.2") L x 1565mm (61.6") W x 127mm (5") H Approximate Installed Weight: 30.99kg (68.32lbs) Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom. Shipping Dimensions: Width: 300mm (12") Length: 1805mm (71") Height: 195mm (8") Shipping Weight: Weight: 35.35kg (78lbs)

This 1964mm/77.3" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Xterra N50. It easily installs using the existing factory mounting points. No drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 1 opening to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit). All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRNX005T - Nissan Xterra N50 Slimline II Roof Rack Kit - by Front Runner Consisting of: 1 x FANX002 - Nissan Xterra N50 Foot Rails - by Front Runner 1 x RRSTA10 - Slimline II Tray - 1165mm(W) X 1964mm(L) - by Front Runner Material used:   Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 32kg (69lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight 36.6kg (80.6lbs)

This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit the Nissan Patrol Y61 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRNPT06L - Nissan Patrol Y61 Slimline II Roof Rack Kit / Tall - by Front Runner Consisting of: 2x LASS027 - Leg Spacer 6mm (Pair)4x LASS103 - No 3 Leg 155mm (Pair)1x RRSTG11 - SLII Tray - 1345mm(W)X2166mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 39.17kg (86.35lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18"); Length: 1730mm (68"); Height: 140mm (6")   Shipping Weight: Weight: 40.03kg (88lbs)

This 2166mm/85.3 long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Patrol/Armada Y62. It easily installs using the existing factory mounting points. No drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack, such as Front Runner tables. These Foot Rails contain 2 openings to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit). All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRNP011T - Nissan Patrol/Armada Y62 (2010-Current)SlimlineIIRoof Rack Kit - by Front Runner Consisting of: 1 x FANP001 - Nissan Patrol/Armada Y62 (2010-Current) Foot Rails - by Front Runner 1 x RRSTG11 - Slimline II Tray - 1345mm(W) X 2166mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 39kg (86lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 455mm (18") Length 1615mm (64") Height 240mm (9") Shipping Weight: Weight: 45.2kg (99.4lbs)

This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y61 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRNP004L - Nissan Patrol Slimline II Roof Rack Kit - by Front Runner Consisting of: 3 x No 1 Leg 120mm (Pair) - by Front Runner 1 x No 2 Leg 130mm (Pair) - by Front Runner 1 x RRSTG11 - Slimline II Tray - 1345mm(W) X 2166mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 34kg (74lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight 39.2kg (86.2lbs)

This 752mm/29.6" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y61 Single Cab contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the Nissan Patrol Y61 Single Cab. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRNP013T - Nissan Patrol Y61 Single Cab Slimline II Roof Rack Consisting of: 1x LASD102 - No 2 Leg Diagonal 130mm (Pair)1x LASS101 - No 1 Leg 120mm (Pair1x RRSTG04 - SLII Tray - 1345mm(W)X752mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 18.59kg (40.98lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18"); Length: 1720mm (68"); Height: 160mm (6")   Shipping Weight: Weight: 22kg (48lbs)