Fatz Fabrication
FATZ FABRICATION Safari 4" Id Ram Head (Clamps Over Outside Of 4" Tube) - 000-135-910
$155.00
Safari 4″ Ram head.
4″ Internal diameter ram head for use with all Fatz Built Safari 4″ Ram Head snorkels. Securing over the top pf the 4″ snorkel to allow maximum flow through the entire surface area of the snorkel. With slotted cut outs on the rear of the head the Safari 4″ Ram Head also offers great water dispersion at the entry point.
JL Audio
JL AUDIO Coaxial Speaker System: 4" (100 Mm) Woofer, 0.75" (19 Mm) Aluminium Dome Tweeter (Sold As Pair) -C1-400x
$159.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, breakaway mounting tabs on the woofer frame allow the C1-400x to be installed in four-hole or two-hole mounting configurations. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound.
At the core of the C1-400x is a proprietary, stamped, steel 4-inch (100 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers. Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition.
The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit. A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 35 W
Peak Music Power: 105 W
Recommended Amplifier Power (RMS): 10 – 50 W / Ch.
System Efficiency: 84.5 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 64 Hz – 24 kHz ± 3 dB
Frame Outer Diameter* (A): 4.03 in / 102 mm
Grille Tray Outer Diameter (B): N/A
Motor Outer Diameter (C): 2.33 in / 59 mm
Frontal Coaxial Tweeter Protrusion** (D): 0.61 in / 16 mm
Frontal Grille Protrusion (E): N/A
Mounting Hole Diameter (F): 3.70 in / 94 mm
Mounting Depth (G): 1.81 in / 46 mm
*Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface
JL Audio
JL AUDIO Coaxial Speaker System: 5.25" (130 Mm) Woofer, 0.75" (19 Mm) Aluminium Dome Tweeter (Sold As Pair) -C1-525x
$209.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-525x is a proprietary, stamped, steel 5.25-inch (130 mm) frame and a DMA-optimized motor system.
A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition.
The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit.
A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 50 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 10 – 75 W / Ch.
System Efficiency: 89.0 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 54 Hz – 24 kHz ± 3 dB
Frame Outer Diameter* (A): 5.83 in / 132 mm
Grille Tray Outer Diameter (B): N/A
Motor Outer Diameter (C): 2.76 in / 70 mm
Frontal Coaxial Tweeter Protrusion** (D): 0.54 in / 14 mm
Frontal Grille Protrusion (E): N/A
Mounting Hole Diameter (F): 4.70 in / 119 mm
Mounting Depth (G): 2.42 in / 62 mm
*Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface
JL Audio
JL AUDIO Coaxial Speaker System: 6.5" (165 Mm) Woofer, 0.75" (19 Mm) Aluminium Dome Tweeter (Sold As Pair) -C1-650x
$209.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, multi-application adaptor rings are included with the C1-650x allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings.
Without the ring, the speaker will fit into many “6-inch” speaker locations as well. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound.
At the core of the C1-650x is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition.
The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit.
A true, 2nd order high-pass filter is employed to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 50 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 10 – 75 W / Ch.
System Efficiency: 90.5 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 48 Hz – 24 kHz ± 3 dB
Frame Outer Diameter* (A): 6.25 in / 159 mm
Grille Tray Outer Diameter (B): N/A
Motor Outer Diameter (C): 3.15 in / 80 mm
Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm
Frontal Grille Protrusion (E): N/A
Mounting Hole Diameter (F): 5.02 in / 128 mm
Mounting Depth (G): 2.07 in / 53 mm *Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from mounting surface
JL Audio
JL AUDIO Coaxial 3-Way Speaker System: 6" X 9" (150 X 230 Mm) Woofer, 1" (25 Mm) Aluminium Dome Tweeter,...
$349.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, spacer adaptor rings are included allowing the C1-690tx to be installed in bottom-mount applications. C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design.
This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound. At the core of the C1-690tx are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system.
A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with dual true, edge-driven, aluminium dome tweeters, the C1-690tx stands apart from others in its category with superior high-frequency clarity and separation. The design of each tweeter delivers inherently excellent off-axis response and high-frequency extension.
Both high-frequency drivers also benefit from the damping of a silk surround suspensions and Ferrofluid in the voice coil gaps, along with the superior strength of neodymium magnetics. A true, mixed order filter network is employed to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 60 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 10 – 100 W / Ch.
System Efficiency: 90.5 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 36 Hz – 24 kHz ± 3 dB
Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm
Grille Tray Outer Diameter (B): N/A
Motor Outer Diameter (C): 3.94 in / 100 mm
Frontal Coaxial Tweeter Protrusion** (D): 0.72 in / 18 mm
Frontal Grille Protrusion (E): N/A
Mounting Hole Diameter (F): N/A
Mounting Depth (G): 3.09 in / 79 mm
*Does not take into account mounting tabs **Frontal coaxial tweeter protrusion measured from the mounting surface
JL Audio
JL AUDIO 2-Way Component System: 6.5" (165 Mm) Woofer, 0.75" (19 Mm) Aluminium Dome Tweeter (Sold As Pair) -C1-650
$269.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, multi-application adaptor rings are included for the C1-650 woofers, allowing easy, drop-in installation in vehicles equipped with oversized 6.5-inch and 6.75-inch speaker openings.
Without the ring, the woofers will also fit into many “6-inch” speaker locations as well. Surface and flush mounts are included with C1 tweeters for maximum installation versatility.
C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound.
At the core of the C1-650 is a proprietary, stamped, steel 6.50-inch (165 mm) frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control the voice coil’s motion.
Tinsel leads are carefully routed and attached to the spiders to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, aluminium dome tweeter, C1 speakers stand further apart from others in its category with superior high-frequency clarity and definition. The tweeter’s design has an inherently excellent off-axis response and high-frequency extension.
It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit.
An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 50 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 10 – 75 W / Ch.
System Efficiency: 91.0 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 59 Hz – 22 kHz ± 3 dB
Frame Outer Diameter* (A): 6.5 in / 165 mm
Grille Tray Outer Diameter (B): 6.84 in / 174 mm
Motor Outer Diameter (C): 3.15 in / 80 mm
Frontal Coaxial Tweeter Protrusion (D): N/A
Frontal Grille Protrusion** (E): 0.85 in / 22 mm
Mounting Hole Diameter (F): 5.56 in / 141 mm
Mounting Depth (G): 2.44 in / 62 mm *Does not take into account mounting tabs **Frontal grille protrusion measured from mounting surface
TWEETER PHYSICAL SPECIFICATIONS:
Flush Mount Fixture Diameter (A1): 1.87 in / 48 mm
Surface Mount Fixture Diameter (A2): 1.69 in / 43 mm
Flush Mount Mounting Hole Diameter (B): 1.625 in / 41 mm
Flush Mount Mounting Depth (C): 0.76 in / 19 mm
Flush Mount Tweeter Frontal Protrusion (D1): 0.29 in / 7 mm
Surface Mount Tweeter Frontal Protrusion (D2): 0.92 in / 23 mm
CROSSOVER PHYSICAL SPECIFICATIONS:
Width (W): 1.96 in / 50 mm
Height (H): 0.90 in / 23 mm
Depth (D): 1.34 in / 34 mm
JL Audio
JL AUDIO 2-Way Component System: 6" X 9" (150 Mm X 230 Mm) Woofer, 1" (25 Mm) Aluminium Dome Tweeter...
$319.00
C1 speakers deliver real substance and great audio performance in a format designed for easy fit behind factory grilles.
To facilitate fit, spacer/adaptor rings are included allowing the C1-690 woofers to be installed in bottom-mount applications. Surface and flush mounts are included with C1 tweeters for maximum installation versatility.
C1 woofer drivers benefit from proprietary FEA modelling and JL Audio’s expertise in low-frequency driver design. This knowledge is used to create speakers that can play loudly while maintaining a smooth, dynamic, low distortion sound.
At the core of the C1-690 are a proprietary, stamped, steel 6 x 9-inch (150 x 230 mm) oval frame and a DMA-optimized motor system. A mineral-filled, injection-moulded polypropylene cone is suspended with a rubber surround on the front, and a carefully engineered flat Conex® spider at the top of the voice coil, to precisely control motion and prevent impact between the voice coil and the backplate.
Tinsel leads are carefully routed and attached to the spider to prevent fatigue and buzzing. These are the same kinds of features and materials normally found on much more expensive loudspeakers.
Equipped with a true, edge-driven, 1-inch aluminium dome tweeter, the C1-690 stands further apart from others in its category with superior high-frequency clarity and definition.
The tweeter’s design has an inherently excellent off-axis response and high-frequency extension. It also benefits from the damping of a silk surround suspension and Ferrofluid in the voice coil gap, along with the superior strength of a neodymium magnet circuit.
An in-line, outboard 2nd order high-pass filter, with Advanced Tweeter Protection Circuitry, is included to further enhance smoothness and improve power handling.
GENERAL SPECIFICATIONS:
Continuous Power Handling (RMS): 60 W
Peak Music Power: 225 W
Recommended Amplifier Power (RMS): 10 – 100 W / Ch.
System Efficiency: 89.0 dB @ 1 W / 1 m
System Nominal Impedance: 4 Ω
System Frequency Response: 39 Hz – 22 KHz ± 3 dB
WOOFER PHYSICAL SPECIFICATIONS:
Frame Outer Diameter* (A): 6.38 x 9.33 in / 162 x 237 mm
Grille Tray Outer Diameter (B): N/A
Motor Outer Diameter (C): 3.54 in / 90 mm
Frontal Coaxial Tweeter Protrusion (D): N/A
Frontal Grille Protrusion (E): N/A
Mounting Hole Diameter (F): N/A
Mounting Depth (G): 2.75 in / 70 mm
*Does not take into account mounting tabs **Frontal grille protrusion measured from the mounting surface
TWEETER PHYSICAL SPECIFICATIONS:
Flush Mount Fixture Diameter (A1): 1.97 in / 50 mm
Surface Mount Fixture Diameter (A2): 2.01 in / 51 mm
Flush Mount Mounting Hole Diameter (B): 1.75 in / 45 mm
Flush Mount Mounting Depth (C): 0.40 in / 10 mm
Flush Mount Tweeter Frontal Protrusion (D1): 0.32 in / 8 mm
Surface Mount Tweeter Frontal Protrusion (D2): 0.87 in / 22 mm
CROSSOVER PHYSICAL SPECIFICATIONS:
Depth (D): 1.34 in / 34 mm
Height (H): 0.90 in / 23 mm
Width (W): 1.96 in / 50 mm
GME
GME 3 Inch Marine Box Speakers Pair - Black - TX667
$95.00
GME 1 WATT UHF CB HANDHELD RADIO - TX667
Product Details
The GME TX667 is an ultra-compact and lightweight mechanical design, with up to 17 hours battery life, convenient USB charging, a high contrast backlit LCD screen, switchable transmission power (1/ 0.5 watt), and a user programmable scan function which makes it the perfect entry-level UHF CB radio.
Features:
Ultra Compact & Lightweight
Up to 17 Hours Battery Life
USB Charging
High Contrast Back-Lit LCD Screen
1/ 0.5 Watt switchable transmission power
What's in the box?
1 Watt UHF CB Handheld Radio (TX667)
1000mAh Li-Ion Battery Pack (BP020)
USB Multi-charging Cable (LE061)
AC Adaptor (PS003)
Belt Clip (MB047)
Part Number: TX667
GME
GME 4 Inch Marine Box Speakers Pair - White - TX667TP
$159.00
GME TX667TP 2-Pack 1W UHF CB Handheld Radio
With an ultra-compact and lightweight mechanical design, up to 17 hours battery life, convenient USB charging, a high contrast backlit LCD screen, switchable transmission power (1/ 0.5 watt), and a user programmable scan function, the TX667 is the perfect entry-level UHF CB radio.
Includes:
2 x 1W UHF CB Handheld Radios (TX667)
2 x 1000mAh Li-Ion Battery Packs (BP020)
1 x AC Adaptor
1 x Twin Desktop Charger
2 x USB Multi-Charging Cables
2 x Belt Clips
Features:
Ultra compact & lightweight
Up to 17 hours battery life
USB multi-charging
High contrast, backlit LCD screen
1/ 0.5 Watt switchable transmission power
Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service
Specifications
Frequency Range TX: 476.425 - 477.4125 MHz
Number of Channels: 80, (75 voice, 2 telemetry RX only, 3 for future use)
Power Supply/Supply Voltage: Li-ion Rechargeable 3.7V DC, 1000 mA
Transmitter:
Transmit Frequency Response: 1 watt - 0.5 watt
Receiver:
Sensitivity: -121 dBm
Intermodulation Immunity: <5% (1 kHz 70%)
Audio Output Power: >0.5 watt max. (8 Ohm)
Dimensions (L x W x H): 52mm x 30mm x 90mm (without antenna)
Weight: 0.8 kg
Warranty:
2 Year Warranty Covered by GME
GME
GME 4 Inch Marine Box Speakers Pair - Black - TX677
$139.00
GME TX677 2W UHF CB Handheld Radio
With a compact and lightweight mechanical design, up to 14 hours battery life, convenient USB charging, a rotary power/volume control for easy operation, switchable transmission power (2/ 0.5 watt), and a user programmable scan function, the TX677 is a serious performer in a compact chassis.
Includes:
1 x 2 Watt UHF CB Handheld Radio (TX677)
1 x 1600mAh Li-Ion Battery Pack (BP027)
1 x USB Multi-Charging Cable
1 x AC Adaptor
1 x Belt Clip
Features:
Up to 14 hours battery life
Compact & lightweight design mechanical design
Rotary power/volume control for easy operation
USB multi-charging
2/0.5W switchable transmission power
Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service
Specifications
Frequency Range TX: 476.425 - 477.4125MHz
Number of Channels: 80, (75 voice, 2 telemetry RX only, 3 for future use)
Channel Spacing: 12.5 kHz
Transmitter:
Transmit Frequency Response: 2 watts/0.5 watt
Audio distortion: <5% (1 kHz 70%)
Receiver:
Sensitivity: -121dBm
Audio Output Power: >0.5 watt max. (8 Ohm)
Power Supply/Supply Voltage: Li-ion rechargeable 3.7V DC, 1600 mA
Dimensions (L x W x H): 52mm x 30mm x 90mm (without antenna)
Warranty:
2 Year Warranty Covered by GME
GME
GME 5 Inch Marine Panel Speakers Pair - White - TX677TP
$249.00
GME TX677TP 2-Pack 2W UHF CB Handheld Radio
With a compact and lightweight mechanical design, up to 14 hours battery life, convenient USB charging, a rotary power/volume control for easy operation, switchable transmission power (2/ 0.5 watt), and a user programmable scan function, the TX677 is a serious performer in a compact chassis.
Includes:
2 x 2 Watt UHF CB Handheld Radios (TX677)
2 x 1600mAh Li-Ion Battery Packs (BP027)
2 x USB Multi-Charging Cable
1 x AC Adaptor
1 x 12V DC Charger
1 x Twin Desktop Charger
2 x Belt Clips
Features:
Up to 14 hours battery life
Compact & lightweight design mechanical design
Rotary power/volume control for easy operation
USB multi-charging
2/0.5W switchable transmission power
Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service
Specifications
Frequency Range TX: 476.425 - 477.4125MHz
Number of Channels: 80, (75 voice, 2 telemetry RX only, 3 for future use)
Channel Spacing: 12.5 kHz
Transmitter:
Transmit Frequency Response: 2 watts/0.5 watt
Audio distortion: <5% (1 kHz 70%)
Receiver:
Sensitivity: -121dBm
Audio Output Power: >0.5 watt max. (8 Ohm)
Power Supply/Supply Voltage: Li-ion rechargeable 3.7V DC, 1600 mA
Dimensions (L x W x H): 52mm x 30mm x 90mm (without antenna)
Warranty:
2 Year Warranty Covered by GME
GME
GME 5 Inch Marine Panel Speakers Pair - Black - TX677QP
$469.00
GME TX677QP 4-Pack 2W UHF CB Handheld Radio
With a compact and lightweight mechanical design, up to 14 hours battery life, convenient USB charging, a rotary power/volume control for easy operation, switchable transmission power (2/ 0.5 watt), and a user programmable scan function, the TX677 is a serious performer in a compact chassis.
Includes:
4 x 2 Watt UHF CB Handheld Radios (TX677)
4 x 1600mAh Li-Ion Battery Packs (BP027)
4 x USB Multi-Charging Cable
1 x AC Adaptor
2 x 12V DC Charger
2 x Twin Desktop Charger
4 x Belt Clips
1 x Rugged premium carry case
Features:
Up to 14 hours battery life (per radio)
Compact & lightweight design mechanical design
Rotary power/volume control for easy operation
USB multi-charging
2/0.5W switchable transmission power
Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service
Specifications
Frequency Range TX: 476.425 - 477.4125MHz
Number of Channels: 80, (75 voice, 2 telemetry RX only, 3 for future use)
Channel Spacing: 12.5 kHz
Transmitter:
Transmit Frequency Response: 2 watts/0.5 watt
Audio distortion: <5% (1 kHz 70%)
Receiver:
Sensitivity: -121dBm
Audio Output Power: >0.5 watt max. (8 Ohm)
Power Supply/Supply Voltage: Li-ion rechargeable 3.7V DC, 1600 mA
Dimensions (L x W x H): 52mm x 30mm x 90mm (without antenna)
Warranty:
2 Year Warranty Covered by GME
GME
GME 6 Inch Marine Panel Speakers Pair - White - TX6600S
$469.00
GME 5/1 UHF CB HANDHELD RADIO IP67 - TX6600S
Featuring class-leading 5 watt transmission power, an IP67 ingress-protection rating for outstanding performance and years of reliable use in the harshest Australian environments. Includes multiple power saving modes, Scansuite digital scanning technology and channel selection with voice announcement. This radio is serious equipment which has proudly been designed, engineered and manufactured in Australia.
The GME TX6600S is ideal for users who demand the ultimate in handheld UHF CB communication, for both work and play. Also suiting a wide range of applications including civil construction, engineering, mining, councils, 4X4 and agriculture. GME has an extensive range of UHF CB Handheld Radios to meet a variety of needs. GME's class leading range, featuring the TX667, TX677, TX6160 and the TX6600S, are built tough and rugged to withstand the Australian landscape. This range features both entry level radio walkie talkies and serious equipment for both work and play.
Features:
Made In Australia
5/1/0.1 Watt switchable transmission power
Rugged Design, IP67 Ingress Protection
ScanSuite™ - Digital Scanning Technology
119 User-programmable RX channels (403-520MHz)
Multiple power saving modes
Two priority channels / Triple watch
Rotary channel selection with voice announcement
MIL-STD 810G
5 Year Warranty
What's in the box?
5 Watt UHF CB Handheld Radio (TX6600S)
2600mAh Li-Ion Battery Pack (BP028)
UHF Antenna 450-490MHz (AE4028)
Desktop Charger (BCD022)
AC Adaptor (PS005)
Belt Clip (MB058)
Part Number: TX6600S
Front Runner
FRONT RUNNER Toyota Land Cruiser Prado / Lexus Gx 550 (2024-Current) Slimsport Rack 40 Light Bar Wind Fairing" - RRAC341
$194.40
$216.00
Lightbar wind fairing for Toyota Land Cruiser Prado 250 (2024-Current) Slimsport Roof Rack Kit / Lightbar Ready or Lexus GX 550 (2024-Current) Slimsport Roof Rack Kit / Lightbar Ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included
Consists of:1 x Toyota Land Cruiser Prado / Lexus GX 550 (2024-Current) Slimsport Rack Wind Fairing Light Bar ReadyHardware KitFitment Guide
Materials used:Black powder-coated steel
Product Dimensions:1188mm (46.8") L x 194mm (7.6") W x 146mm (5.7") H
Weight:3.3Kg (7.3lbs)
Front Runner
FRONT RUNNER Toyota Land Cruiser Prado / Lexus Gx 550 (2024-Current) Slimsport Rack Wind Fairing - RRAC340
$194.40
$216.00
Smooth out the ride in your Toyota Land Cruiser Prado or Lexus GX 550 in more ways than one with the Slimsport Rack Wind Fairing. The Wind Fairing channels air fluidly over the rack and accessories to help reduce drag and wind noise. It mounts quickly to the front of your roof rack.
A wind fairing for the Toyota Land Cruiser Prado 250 (2024-Current) Slimsport Roof Rack Kit or Lexus GX 550 (2024-Current) Slimsport Roof Rack Kit .
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Toyota Land Cruiser Prado / Lexus GX 550 (2024-Current) Slimsport Rack Wind FairingHardware KitFitment Guide
Materials used:Black powder-coated steel
Product Dimensions:1188mm (46.8") L x 189mm (7.4") W x 133mm (5.2") H
Weight:3.8Kg (8.4lbs)
Front Runner
FRONT RUNNER Subaru Outback Gen 6 (2020-Current) Slimsport Rack 40 Light Bar Wind Fairing - RRAC328
$188.10
$209.00
Get ready to light up the night while reducing drag and noise with this 40” Light Bar Wind Fairing for the Slimsport Rack on your Subaru Outback GEN 6. It also improves fuel consumption when you have bulky items on the rack and its durable rubber beading, found on the bottom edge, gives added protection when going over rough terrain.
Lightbar wind fairing for Subaru Outback GEN 6 (2020-Current) Slimsport Roof Rack Kit / Lightbar Ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber beading is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Subaru Outback Slimsport Rack Light Bar Wind Fairing1 x Wind Fairing Rubber - 950mm (L)1 x Clear VinylInstallation HardwareFitting Instructions
Materials used:Black powder-coated high strength steel
Product Dimensions:73mm (2.9") L x 1145mm (45.1") W x 206mm (8.1") H
Weight:2.99Kg (6.6lbs)
Front Runner
FRONT RUNNER Subaru Outback Gen 6 (2020-Current) Slimsport Rack Wind Fairing - RRAC327
$188.10
$209.00
Reduce noise levels and improve the airflow over the Slimsport Roof Rack of your Subaru Outback GEN 6 with this easy-to-fit Wind Fairing. It certainly helps reduce fuel consumption on a loaded rack and its durable rubber beading, found on the bottom edge, gives added protection when going over rough terrain.
A wind fairing for the Subaru Outback GEN 6 (2020-Current) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber beading is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Subaru Outback Slimsport Rack Wind Fairing1 x Wind Fairing Rubber - 950mm (L)1 x Clear VinylInstallation HardwareFitting Instructions
Materials used:Black powder-coated high strength steel
Product Dimensions:79mm (3.1") L x 1145mm (45.1") W x 201mm (7.9") H
Weight:3.53Kg (7.8lbs)
Front Runner
FRONT RUNNER Volkswagen T5/T6/T6.1 Transporter Swb Slimsport Rack Wind Fairing - RRAC293
$174.60
$194.00
Enjoy a much quieter ride in your Volkswagen T5/T6/T6.1 with this Slimsport Rack Wind Fairing. It seamlessly channels air up and over the rack, reducing noise and fuel consumption.
A wind fairing for the Volkswagen T5/T6/T6.1 Transporter SWB (2003-2024) Slimsport Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Volkswagent T5/T6/T6.1 Slimsport Rack Wind FairingInstallation HardwareFitting Instructions
Materials used:Black powder coated steel
Product Dimensions:1344mm (52.9") L x 185mm (7.3") W x 155mm (6.1") H
Weight:2.3kg (5.1lbs)
Front Runner
FRONT RUNNER Toyota Sequoia (2023-Current) Slimsport Rack 40 Light Bar Wind Fairing - RRAC286
$226.80
$252.00
Improve aerodynamics and enjoy a quieter ride on your loaded Toyota Sequoia with the specially-designed Slimsport Rack Wind Fairing. This innovative accessory reduces drag and minimizes wind noise by efficiently channeling air over your Slimsport Roof Rack. This particular model features a 40" cutout to allow the use of the Front Runner 40" Light Bar, so you can keep exploring even after the sun goes down.
Lightbar wind fairing for the Toyota Sequoia (2023-Current) Slimsport Roof Rack Kit / Lightbar Ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Toyota Sequoia 40" light bar wind fairingFitment Guide Installation Hardware
Materials used:Black powder-coated high strength steel
Product Dimensions:1281mm (50.4") L x 169mm (6.7") W x 172mm (6.8") H
Weight:4kg (8.8lbs)
Front Runner
FRONT RUNNER Toyota Sequoia (2023-Current) Slimsport Rack Wind Fairing - RRAC285
$226.80
$252.00
Enhance the aerodynamics of your Toyota Sequoia and experience a smoother, quieter ride when you’re hauling loads with the purpose-built Slimsport Rack Wind Fairing. This innovative accessory is designed to minimize drag and reduce wind noise by effectively directing airflow over your Slimsport Roof Rack (and the gear loaded on it).
A wind fairing for the Toyota Sequoia (2023-Current) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Toyota Sequoia (2023-Current) Slimsport Rack Wind Fairing1 x Fitting InstructionsInstallation Hardware
Materials used:Black powder coated high strength steelStainless steel fasteners
Product Dimensions:1311mm (51.6") L x 241mm (9.5") W x 143mm (5.6") H
Weight:4.2kg (9.3lbs)
Front Runner
FRONT RUNNER Chevrolet Colorado/Gmc Canyon (2015-2022) Slimsport Rack 40 Light Bar Wind Fairing - RRAC262
$158.00
$176.00
Be more economical when hauling gear and add light to your Chevrolet Colorado or GMC Canyon (2015-2022) with this specially-designed wind fairing. The Slimsport Rack Wind Fairing channels air fluidly over your Slimsport Roof Rack (and the accessories loaded on it). This particular fairing is specifically designed to pair with the 40” Front Runner Light Bar because adventures don't end when the sunlight does.
Lightbar wind fairing for Chevrolet Colorado/GMC Canyon (2015-2022) Slimsport Roof Rack Kit / Lightbar Ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Chevrolet Colorado/GMC Canyon Slimsport Rack 40" Light Bar Wind FairingFitting InstructionsInstallation HardwareMaterials used:Black powder coated steelProduct Dimensions:1450mm (57.1") L x 255mm (10") W x 55mm (2.2") HWeight:2.7kg (5.9lbs)
Front Runner
FRONT RUNNER Chevrolet Colorado/Gmc Canyon (2015-2022) Slimsport Rack Wind Fairing - RRAC261
$179.00
$199.00
Reduce drag and wind noise on your Chevrolet Colorado or GMC Canyon with this specially-designed Slimsport Rack Wind Fairing. It channels air fluidly over your Slimsport Roof Rack (and all the accessories and cargo loaded on it) and also acts as a roof guard when traveling over rough terrain.
A wind fairing for the Chevrolet Colorado/GMC Canyon (2015-2022) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Slimsport Rack Wind FairingInstallation HardwareFitting Instructions
Materials used:Black powder coated steel
Product Dimensions:1175mm (46.3") L x 176mm (6.9") W x 187mm (7.4") H
Weight:2.9kg (6.4lbs)
Front Runner
FRONT RUNNER Toyota Rav4 (2019-Current) Slimsport Rack Wind Fairing - RRAC238
$226.80
$252.00
Reduce the drag and wind noise over the roof rack of your Toyota Rav4 with a wind fairing. The Slimsport Rack Wind Fairing channels air fluidly over your Slimsport Roof Rack (and the accessories loaded on it) to help reduce fuel consumption. It mounts quickly to the front of your roof rack and adds an overall bolder look.
A wind fairing for the Toyota Rav4 (2019-Current) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Toyota Rav4 Slimsport Rack Wind Fairing1 x Protection StripInstallation HardwareFitting Instructions
Materials used:Black powder coated steel
Product Dimensions:1175mm (46.3") L x 172mm (6.8") W x 203mm (8") H
Weight:3.25kg (7.2lbs)
Front Runner
FRONT RUNNER Subaru Xv Crosstrek 2Nd Gen (Gt) (2017-2023) Slimsport Rack Wind Fairing - RRAC235
$146.70
$163.00
Smooth out the ride in your Subaru XV Crosstrek in more ways than one with the Slimsport Rack Wind Fairing. The Wind Fairing channels air fluidly over the rack and accessories to help reduce drag and wind noise. It mounts quickly to the front of your roof rack and adds an overall bolder look.
A wind fairing for the Subaru XV Crosstrek 2nd Gen (GT) (2017-2023) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Subaru XV Crosstrek 2nd Gen (GT) (2017-2023) Slimsport Rack Wind Fairing1 x Protection StripInstallation HardwareFitting Instructions
Materials used:Black powder coated steel
Product Dimensions:1140mm (44.9") L x 171mm (6.7") W x 129mm (5.1") H
Weight:2.89kg (6.4lbs)
Front Runner
FRONT RUNNER Toyota Rav4 (2019-Current) Slimsport Rack 40 Light Bar Wind Fairing - RRAC220
$226.80
$252.00
The Slimsport Rack Wind Fairing is specifically designed to pair with the 40” Front Runner Light Bar for a sleek look and even more functionality. After all, adventures don't end just because the sun goes down.
Light Bar Wind Fairing for the Toyota Rav4 (2019-Current) Slimsport Roof Rack Kit
Allows installation of Front Runner 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount
Designed to direct airflow over the rack and accessories, reducing drag and wind noise
Helps reduce fuel consumption while carrying bulky loads
Durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain
Brackets and installation hardware included
Consists of:1 x Toyota Rav4 Slimsport Rack 40" Light Bar Wind FairingInstallation HardwareFitting Instructions
Materials used:Black powder coated steel
Product Dimensions:1175mm (46.3") L x 178mm (7") W x 161mm (6.3") H
Weight:4.94kg (10.9lbs)
Front Runner
FRONT RUNNER Subaru Xv Crosstrek 2Nd Gen (Gt) (2017-2023) Slimsport Rack 40 Light Bar Wind Fairing - RRAC211
$146.70
$163.00
Seamlessly integrate the Slimsport Rack Fairing specifically designed to pair with the 40” Front Runner Light Bar for a sleek look and even more functionality. After all, adventures don't end just because the sun goes down.
Lightbar wind fairing for .
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Consists of:1 x Slimsport Rack 40" Light Bar Wind Fairing1 x Protection StripInstallation HardwareFitting InstructionsMaterials used:Black powder coated steel
Product Dimensions:1140mm (44.9") L x 163.5mm (6.4") W x 116mm (4.6") H
Weight:2.1kg (4.6lbs)
Front Runner
FRONT RUNNER Toyota Tacoma (2005-Current) Slimsport Rack 40 Light Bar Wind Fairing - RRAC192
$110.70
$123.00
Seamlessly integrate the Slimsport Rack Fairing specifically designed to pair with the 40” Front Runner Light Bar for a sleek look and even more functionality. After all, adventures don't end just because the sun goes down.
Lightbar wind fairing for Toyota Tacoma (2005-2023) Slimsport Roof Rack Kit / Lightbar ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Front Runner
FRONT RUNNER Wind Fairing For Low Profile Rack / 1165Mm/1255Mm(W) - RRAC174
$202.50
$225.00
Make a statement and change the standard Front Runner rack Wind Deflector to this bold Front Runner Wind Fairing for Low Profile rack kits. Quickly mounts to the front of your roof rack to help move air over large rack loads and accessories, while reducing wind noise at high speeds.
Get a bold new overlanding look in minutes.
Create a solid appearance by covering the gap from roof to rack.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
Easily secures to your roof rack in three simple steps.
Adjustable brackets allow the Wind Fairing to be correctly angled and positioned on your vehicle.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
An optional clear protective strip is included to eliminate any potential rare minor scuffing caused by heavy dust.
Consists of:1 x Wind Fairing4 x Brackets1 x Rubber BladeInstallation HardwareFitting instructions
Materials used:Black powder coated aluminumEPDM Rubber
Product Dimensions:1087mm(42.8") L x 2mm(0.1") W x 127mm(5") H
Weight:1.5kg (3.3lbs)
Front Runner
FRONT RUNNER Tyre Inflate 830 - REQU329
$129.00
$143.00
Quickly get your tyres up to their optimum pressures with the OSRAM TYREinflate 830. Thanks to the 4-metre power cable, it can easily access all four tyres and just plugs into your vehicle's 12V socket. This is great for driving on soft sand, gravel, or rocks, where you must deflate and inflate tyres.
The OSRAM TYREinflate 830 has been specially developed for use with larger vehicles and their tyres, making it ideal for cars, caravans, motorhomes, off-road vehicles, minibuses and vans.
This tyre inflator can inflate a 13" tyre in approx. 2 minutes and a 22" tyre in approx. 5 minutes.
The auto stop function and the deflator valve help to keep the tyres optimally inflated.
This can also reduce the risk of over- or under-inflation and the resulting possible damage to the tyres.
The TYREinflate 830 has a 4-metre power cable for the accessibility to all four tyres and plugs directly into your vehicle's 12-volt socket.
The backlit LED display and integrated LED light provide improved readability of the pressure settings and improved illumination of the working area even in reduced visibility conditions or at night.
Also included are three adapters for inflating sports balls and other small inflatables and a storage bag to protect the unit and store it neatly.
OSRAM offers a 2-year guarantee on this product.
Based on inflating a 13” tyre from flat to 2.4 BAR /22” tyre from flat to 2.6 bar.
Measurements of the tyre pressure and inflation of the tyres to the optimum tyre pressure must always be conducted on cold tyres.
Consists of:1 x Large Vehicle Digital Tyre InflatorInstallation HardwareFitting Instructions
Product Dimensions:250mm (9.84") L x 150mm (5.9") W x 100mm (3.93") HWeight:2.6kg (5.7lbs)
Special Notes:180W12VGuarantee: 2 yearsSupplier SKU: OTI830
FOCAL
FOCAL 6.5" Speaker Coaxial Component Protective Grills Covers Only (Pair) -GRILLE 6.5” (pair)
$120.00
THE ESSENTIAL ACCESSORY
SPEAKER DRIVER GRILLE
This 6.5” midrange grille, 100% chemical etching, with an aluminium ring, draws on the codes of our new Utopia M range with its unique ‘M’ profile and will help you achieve a seamless integration into your vehicle.
FOCAL
FOCAL Tweeter Kit (Pair) 4Khz - 21Khz, Complete With Inline Crossovers And Flush And Surface Mounting Accessories | - Twu1.5...
$125.00
The TWU1.5 tweeter is designed for custom installation with existing Universal range kits. Easy to fit, four different mounting options are available: flush fit, on angled stand, flat or straight behind the original grill, removing the tweeter from its Focal bracket. This inverted dome tweeter is made of aluminium/magnesium alloy. This gives the trebles an extended frequency response of up to 21 kHz, for clearer, more detailed reproduction.
Sold in pairs.
NATURAL, UNCOLOURED SOUND
The Integration range is synonymous not only with ease of installation but also and most especially, with sound quality. At Focal we pride ourselves in supplying equipment of impeccable quality: for example, a polyglass membrane for natural, uncoloured sound and an inverted dome aluminium/magnesium tweeter for clear, detailed reproduction.
RELIABILITY A TOP PRIORITY
The Focal spirit also encompasses the reliability of our ever evolving technological equipment. Butyl suspension ensures that your speakers will stand the test of time. You will be able to enjoy the Focal sound for a long time, thanks to our high quality design: manufacturing processes and the choice of materials are always high priorities for our engineers, guaranteeing a result that exceeds your expectations.
WHAT MAKES IT SPECIAL
High sensitivity
No-fuss treble adjustment
Shallow fitting
Improves on original-fit speakers
Dynamism and neutrality
FOCAL
FOCAL 6.5Km K2 Power M Series 6-1/2" Component Woofers (Pair) -6.5KM WOOFER (pair)
$1,175.00
Manufactured in France
Focal is known for innovative design and accurate sound, and they continue their impressive record of revolutionary hi-fi car audio with the K2 Power M Series. The Focal 6.5KM 6-1/2" component woofers are designed, engineered, and manufactured at Focal's facilities in France for true hi-fi sound in custom installations. This pair of Focal 6.5KM component woofers will handle the low-end detail and dynamics in your K2 Power M Series component system.
Powerful sound
Focal engineers applied some of their most innovative technologies, including an M-profile Aramid fiber cone, to make these 6-1/2" woofers uniquely equipped for high-performance playback. The shape and material help reduce harmonic distortion so you'll enjoy Focal's signature clean, unstressed, K2 sound.
Focal also prioritizes shallow depth to make this special speaker a better fit for more installation locations. And with power handling up to 120 watts RMS, you can safely drive this speaker with a healthy amount of power.
Product highlights:
6-1/2" component woofers (pair)
"M"-profile Aramid fiber woofer cone
tuned mass damper surround
crossovers not included
super-rigid aluminum basket
neodymium magnet
4-ohm impedance
handles up to 120 watts RMS (240 watts peak power)
frequency response: 50-5,000 Hz
sensitivity at 2.83V: 92.5 dB
top-mount depth: 2-1/8"
grille not included
warranty: 1 year
MFR # 6.5KM
Item # 09165KM
What's in the box:
Two 6.5 KM Woofers
Focal Performance owner's manual
Eight 1-1/8" Screws
Eight speed clips
Quick start guide
Features & specs
General
Speaker Size
6 1/2
Design
1-way
Tweeter Design
---
Impedance (Ohms)
4
Tweeter Composition
---
Woofer Composition
Aramid Fiber
Woofer Surround
Rubber
Parts Warranty
1 Year
Labor Warranty
1 Year
Specifications
Sensitivity (1W at 1 meter)
N/A
Sensitivity at 2.83 volts
93
Frequency Response
50 - 5k Hz
Minimum RMS Wattage
---
Maximum RMS Wattage
120
Peak Power Handling (Watts)
240
Top-mount Depth (Inches)
2 3/16
Bottom-mount Depth (Inches)
N/A
Cutout Diameter or Length (inches)
5 5/8
Mounting Height (Inches)
0.45
Frame Width
6.494
Frame Length
6.494
FOCAL
FOCAL Frak K2 Power M Series 1-1/4" 'M'-Profile Inverted Dome Tweeters (Pair) -FRAK TWEETER (pair)
$699.00
Manufactured in France
Focal is known for innovative design and accurate sound, and they continue their impressive record of revolutionary hi-fi car audio with the K2 Power M Series. These Focal FRAK 1-1/4" component tweeters are designed, engineered, and manufactured at Focal's facilities in France for true hi-fi sound in custom installations. These Focal FRAK component tweeters will faithfully reproduce the high-frequency detail and dynamics as part of a K2 Power M Series component system.
Astonishing detail
Focal engineers applied some of their most innovative technologies, including an M-profile aluminum/magnesium cone, to make these tweeters uniquely equipped for high-performance playback. The shape and material help reduce harmonic distortion so you'll enjoy Focal's signature clean, unstressed, K2 sound.
Focal also prioritizes shallow depth to make this special speaker a better fit for more installation locations. And with power handling up to 25 watts RMS, you can safely drive this speaker with a healthy amount of power.
Product highlights:
1-1/4" tweeters
aluminum 'M'-profile cone design
tuned mass damper surround
includes mounting brackets and grilles
4-ohm impedance
handles up to 25 watts RMS (150 watts peak power)
frequency response: 600-32,000 Hz
sensitivity: 91 dB at 2.83 volts
top-mount depth: 3/4"
warranty: 1 year
MFR # FRAK
Item # 091FRAK
Features & specs
General
Speaker Size
1 1/4
Design
1-way
Tweeter Design
M-Profile Cone
Impedance (Ohms)
4
Tweeter Composition
Aluminum
Woofer Composition
---
Woofer Surround
Rubber
Parts Warranty
1 Year
Labor Warranty
1 Year
Specifications
Sensitivity (1W at 1 meter)
N/A
Sensitivity at 2.83 volts
91
Frequency Response
600 - 32k Hz
Minimum RMS Wattage
---
Maximum RMS Wattage
25
Peak Power Handling (Watts)
150
Top-mount Depth (Inches)
0 3/4
Bottom-mount Depth (Inches)
N/A
Cutout Diameter or Length (inches)
2
Mounting Height (Inches)
0.5
Frame Width
2.3
Frame Length
2.3
What's in the box:
2 Tweeters
Focal owner's manual
2 Steel mounting rings
Quick start guide
Rhino-Rack
RHINO-RACK Vortex Complete Roof Rack Bundle For Byd Shark 6 - RX100-VA137B-LORD
$499.00
Conquer any adventure with the Rhino-Rack Vortex Complete Roof Rack Bundle for BYD Shark 6 - your professional solution for superior cargo carrying, aerodynamic performance, and reliability. Designed for adventurers, tradies, and weekend warriors, this proven system delivers strength, style, and security perfectly matched to your BYD Shark 6.
WHAT'S INCLUDED?
2X Rhino-Rack Vortex Bars (Black 1375mm) - aerodynamic design with VGS rubber strip
RX100 Leg System (x4) - 'Overland Tough' construction for BYD Shark 6 raised rails
VGS Rubber Strip - reduces wind drag and noise
Security Hardware - theft protection included
End Caps - complete professional finish
KEY BENEFITS
Aerodynamic Vortex design minimizes wind noise
'Overland Tough' construction for maximum durability
VGS rubber strip provides roof protection and noise reduction
Complete security hardware protects against theft
Seamless vehicle integration with sleek appearance
INSTALLATION OPTIONS
Choose DIY installation with Rhino-Rack's comprehensive step-by-step guide, or let our experienced team at TJM Northern Beaches handle the professional installation for you. With 15+ years of 4X4 expertise, we ensure perfect fitment and optimal performance for your specific vehicle.
Ready to upgrade your BYD Shark 6's roof carrying capacity? Contact TJM Northern Beaches today.
Rhino-Rack RX100
The Rhino-Rack RX100 roof rack system is designed specifically for use with roofs that feature raised rails. Built 'Overland Tough' with rugged good looks and vigorously tested to meet the needs of any adventurer, tradie or weekend warrior.
The system suits a wide range of activities and comes with security hardware to protect your racks against theft. The RX leg provides a seamless transition between product and vehicle, for a sleek look that doesn't compromise functionality. The system comes with a comprehensive step-by-step installation guide, for adventurers who choose to self-install.
100% load capacity in all conditions
System rated to 100kg/220lbs* or vehicle manufacturer’s roof load limit. Know your limits, visit www.rhinorack.com/loadrating.
Quick and easy installation and compatible with Rhino-Rack Vortex™ Bars and Pioneer™ Platforms
City Crash and durability tested by independent labs making it suitable for off-road use
Easy access to Vortex™ Bar channel for quick accessory installation
KEY BENEFITS
Package length: 500 mm
Package width: 140 mm
Package height: 90 mm
Warranty: 5 Years
Country of Origin: Australia
Rhino-Rack Vortex Bars
The Rhino-Rack Vortex bars can be purchased in black or silver and are cut to 7 different predefined lengths to suit different vehicles. All bars include the VGS rubber strip which has been designed to reduce wind drag and noise as well as providing added protection for your roof racks and load. All bars include end caps.
Vortex Bars available to replace your current bars (sold individually)
Bars come in black and silver colour options
Bars are cut to predefined lengths and are priced accordingly
All Vortex bars come with end caps
All Vortex Bars come with the VGS strip
KEY BENEFITS
Package length: 1440 mm
Package width: 90 mm
Package height: 50 mm
Warranty: 5 Years
Country of Origin: Australia
Lightforce
LIGHTFORCE Beast 230Mm Clear Spot Filter- F230BEASTSC
$41.40
$46.00
LIGHTFORCE BEAST 230MM CLEAR SPOT FILTER- F230BEASTSC
Lightforce’s unique Modular Filter System has been applied to the new Beast LED Driving Light. The Clear Spot Filter adds even more protection over the moulded Beast lens and the bezel from road debris and impacts, without affecting the driving light's beam pattern.
Specifications
Colour: Clear
Beam Pattern: Spot
Size: 230mm
Material: Polycarbonate
Lightforce
LIGHTFORCE Beast Led Driving Light Cover (Black)-F230BEASTBC
$41.40
$46.00
Lightforce’s unique Modular Filter System has been applied to the new Beast LED Driving Light. The black covers add even more protection over the moulded Beast lens and the bezel from road debris and impacts. It is also ideal for those who like a modern look when wanting to promote the “Lightforce” Driving Light brand.
Specifications
Colour: Black
Beam Pattern: N/A Cover only
Size: 230mm
Material: Polycarbonate
*Do not operate lights with black cover fitted.
