Front Runner
FRONT RUNNER Nissan Frontier 3Rd Gen (2021-Current) Slimline Ii Roof Rack Kit - KRNF004T
$1,477.80
$1,642.00
Get your third-generation Nissan Frontier ready for any adventure when you fit this Slimline II Roof Rack kit. With 55+ accessories for this rack, you can load up the camping, overlanding and sports gear you need for your adventures.
This 1358mm/53.5" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Frontier. It easily installs using the existing factory mounting points. No drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables.
These Foot Rails contain 1 opening to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit).
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNF004T - Nissan Frontier 3rd Gen (2021-Current) Slimline II Roof Rack Kit
Consisting of:
1x FANF001 - Nissan Frontier 3rd Gen (2021-Current) Foot Rails
1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)
Material Used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 24.42kg (53.84lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle's roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 445mm (18")
Length: 1720mm (68")
Height: 255mm (10")
Shipping Weight:
Weight: 35kg (77lbs)
Front Runner
FRONT RUNNER Nissan Navara (2014-Current) Egr Rolltrac Load Bed Load Bar Kit - KRRT009
$546.30
$607.00
A set of Pickup Bed Load Bars used to transport gear over the bed of your Nissan Navara when fitted with an EGR RollTrac roll cover. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 1475mm Load Bars that fit into the EGR RollTrac cover tracks, and fitting instructions.
The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly onto the EGR RollTrac cover tracks.
Allows for gear to be mounted above the pickups load bed.
The load bed retains its load-carrying ability, while the drop-down door functions as usual.
Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
Made from stainless steel and a durable, weather-resistant black powder coated aluminum.
Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle.
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT009 - Nissan Navara (2014-Current) EGR RollTrac Load Bed Load Bar Kit
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LBSK017 - Roof Load Bar Pair 1475mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 8.54kg (18.83lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 160mm (6")
Length: 1590mm (63")
Height: 160mm (6")
Shipping Weight:
Weight: 8.4kg (18lbs)
Front Runner
FRONT RUNNER Nissan Navara (2014-Current) Egr Rolltrac Slimline Ii Load Bed Rack Kit - KRRT042T
$1,420.20
$1,578.00
This kit creates a full-size rack that sits above your Nissan Navara's load bed when fitted with an EGR RollTrac cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1475mm x 1156mm) and 4 Pickup Roll Top Leg Mounts that fit into the existing EGR RollTrac channels.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT042T - Nissan Navara (2014-Current) EGR RollTrac Slimline
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x RRSTM06 - SLII Tray - 1475mm(W)X1156mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 26.15kg (57.65lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 440mm (17")
Length: 1730mm (68")
Height: 240mm (9")
Shipping Weight:
Weight: 26.2kg (58lbs)
Front Runner
FRONT RUNNER Nissan Navara D23 4Th Gen (2021 - Current) Slimline Ii Roof Rack Kit - KRNN005T
$1,421.10
$1,579.00
This 1358mm/53.5 long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Navara D23 4th Gen. Drilling is required for installation.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
The vehicle-specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit).
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNN005T - Nissan Navara D23 4th Gen (21 - Cur)SLII RRack Kit
Consisting of:
1x FANN004 - Nissan Navara D23 4th Gen (2021 - Curr) Foot Rail1x RRSTD07 - SLII Tray - 1255mm(W)X1358mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 29.67kg (65.41lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 440mm (17"); Length: 1730mm (68"); Height: 250mm (10")
Shipping Weight:
Weight: 33kg (73lbs)
Front Runner
FRONT RUNNER Nissan Navara/Frontier D23 3Rd Gen (2014-2020) Slimline Ii Roof Rack Kit - KRNN002T
$1,457.10
$1,619.00
This 1358mm/53.5" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Navara/Frontier D23 Double Cab. Drilling is required for installation.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables.
These Foot Rails contain 1 opening to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit)*.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
*Note: Table opening only works with models that do not have the factory rails fitted.
Features
KRNN002T - Nissan Navara D23 3rd Gen (2014-2020) Slimline II Roof Rack Kit - by Front Runner
Consisting of:
1 x FANN002 - Nissan Navara/Frontier D23 DC Foot Rails - by Front Runner
1 x RRSTD07 - Slimline II Tray - 1255mm(W) X 1358mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 26kg (57lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 240mm (9")
Shipping Weight:
Weight 30.3kg (66.7lbs)
Front Runner
FRONT RUNNER Nissan Navara/Frontier D23 Dc Sump Guard - SGNN001
$604.00
$671.00
Front Runner sump guards are designed for specific vehicle makes and models to ensure that the correct parts of the vehicle are protected from damage.
Made of 3mm high strength steel and black powder coated for added resistance to the elements.
Installs to existing mounting points underneath the Nissan Navara/Frontier.
Fits both left and right hand drive vehicles.
Cut outs around integral areas do not hinder the functionality of the vehicle's factory fitted parts, such as the recovery points.
Easy installation. Uses factory mounting points with no drilling or vehicle modification required.
Features
Consists of:
1 x Sump Guard
1 x Belly Guard
Installation Hardware
Fitting Instructions
Materials used:
3mm Black powder coated high strength steel
Product Dimensions:
959mm (37.8") L x 807mm (31.8") W x 223mm (8.8") H
Weight:
15.7kg (34.6lbs)
Front Runner
FRONT RUNNER Nissan Nv200 (2009-Current) Slimline Ii Roof Rack Kit - KRNN003T
$1,665.00
$1,850.00
This 1560mm/61.4" long, full-size, Slimline II cargo carrying roof rack kit for the Nissan NV200 contains the Slimline II Tray, Wind Deflector, 2 Tracks and 6 Feet. Drilling is required for installation.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNN003T - Nissan NV200 (2009-Current) Slimline II Roof Rack Kit - by Front Runner
Consisting of:
2x FASS012 - Foot Set / 40mm - 50mm
1x FASS013 - Foot Set / 60mm - 70mm
1x RRSTD08 - SLII Tray - 1255mm(W)X1560mm(L)
1x TRAC010 - Universal Track Non Drilled / 1800mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 29.86kg (65.83lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 440mm (17")
Length: 1805mm (71")
Height: 270mm (11")
Shipping Weight:
Weight: 29.2kg (64lbs)
Front Runner
FRONT RUNNER Nissan Patrol Load Bar Kit / Gutter Mount - KRNP009
$468.00
$520.00
A set of Gutter Mounted Load Bars used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 120mm Gutter Mount legs, 2 1345mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to a vehicle with gutters.
You may not have the need for a full roof rack and find that you can get by using a set of Front Runner load bars.
Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred.
The Load Bars are mounted directly to the rain gutters using Gutter Mounted Legs.
Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks.
The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats.
The Load Bars and Gutter Mount Legs can be used in the future as components to build a complete Front Runner Roof Rack.
Made from stainless steel and a durable, weather resistant black powder-coated aluminum.
Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle.
Features
KRNP009 - Nissan Patrol Load Bar Kit / Gutter Mount - by Front Runner
Consisting of:
2 x LASS101 - No 1 Leg 120mm (Pair - by Front Runner
1 x LBSK015 - Roof Load Bar Pair 1345mm(W) - by Front Runner
1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 7kg (16lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above.
If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters.
If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 120mm (5")
Length 1455mm (57")
Height 170mm (7")
Shipping Weight:
Weight 8.2kg (18.1lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y60 Slimline Ii Roof Rack Kit / Low Profile - KRNP010L
$2,271.60
$2,524.00
This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y60 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: This rack kit is not suitable for under rack table fitment.
Features
KRNP010L - Nissan Patrol Y60 Slimline II Roof Rack Kit / Low Profile - by Front Runner
Consisting of:
4x LASS102 - No 2 Leg 130mm (Pair)
1x RRSTJ11 - SLII Tray - 1425mm(W)X2166mm(L)
1x WDST009 - Wind Deflector 20mm Lip Wide Pair / 1345mm(W)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 41.76kg (92.06lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 450mm (18")
Length: 1730mm (68")
Height: 140mm (6")
Shipping Weight:
Weight: 40.72kg (90lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y60 Slimline Ii Roof Rack Kit / Tall - KRNPT10L
$2,271.60
$2,524.00
This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y60 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. Installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNPT10L - Nissan Patrol Y60 Slimline II Roof Rack Kit Tall
Consisting of:
4 x LASS103 - No 3 Leg 155mm (Pair) - by Front Runner
1 x RRSTJ11 - Slimline II Tray - 1425mm(W) X 2166mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 35kg (77lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 140mm (6")
Shipping Weight:
Weight 41.0kg (90.1lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y61 3 Door (1998-2010) Slimline Ii Roof Rack Kit - KRNP012T
$1,893.60
$2,104.00
This 1762mm/69.4" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y61 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the Nissan Patrol Y61. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNP012T - Nissan Patrol Y61 3 Door (1998-2010) Slimline II R
Consisting of:
4x LASS102 - No 2 Leg 130mm (Pair)1x RRSTG09 - SLII Tray - 1345mm(W)X1762mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 34.46kg (75.97lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 455mm (18"); Length: 1730mm (68"); Height: 270mm (11")
Shipping Weight:
Weight: 36kg (79lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y61 Single Cab Slimline Ii Roof Rack Kit - KRNP013T
$1,006.20
$1,118.00
This 752mm/29.6" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y61 Single Cab contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the Nissan Patrol Y61 Single Cab. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNP013T - Nissan Patrol Y61 Single Cab Slimline II Roof Rack
Consisting of:
1x LASD102 - No 2 Leg Diagonal 130mm (Pair)1x LASS101 - No 1 Leg 120mm (Pair1x RRSTG04 - SLII Tray - 1345mm(W)X752mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 18.59kg (40.98lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 445mm (18"); Length: 1720mm (68"); Height: 160mm (6")
Shipping Weight:
Weight: 22kg (48lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y61 Slimline Ii Roof Rack Kit - KRNP004L
$2,154.60
$2,394.00
This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit for the Nissan Patrol Y61 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNP004L - Nissan Patrol Slimline II Roof Rack Kit - by Front Runner
Consisting of:
3 x No 1 Leg 120mm (Pair) - by Front Runner
1 x No 2 Leg 130mm (Pair) - by Front Runner
1 x RRSTG11 - Slimline II Tray - 1345mm(W) X 2166mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 34kg (74lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 140mm (6")
Shipping Weight:
Weight 39.2kg (86.2lbs)
Front Runner
FRONT RUNNER Nissan Patrol Y61 Slimline Ii Roof Rack Kit / Tall - KRNPT06L
$2,230.20
$2,478.00
This 2166mm/85.3" long full-size Slimline II cargo carrying roof rack kit the Nissan Patrol Y61 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. It installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNPT06L - Nissan Patrol Y61 Slimline II Roof Rack Kit / Tall - by Front Runner
Consisting of:
2x LASS027 - Leg Spacer 6mm (Pair)4x LASS103 - No 3 Leg 155mm (Pair)1x RRSTG11 - SLII Tray - 1345mm(W)X2166mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 39.17kg (86.35lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 450mm (18"); Length: 1730mm (68"); Height: 140mm (6")
Shipping Weight:
Weight: 40.03kg (88lbs)
Front Runner
FRONT RUNNER Nissan Patrol/Armada Y62 (2010-Current) Slimline Ii Roof Rack Kit - KRNP011T
$2,276.10
$2,529.00
This 2166mm/85.3 long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Patrol/Armada Y62. It easily installs using the existing factory mounting points. No drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack, such as Front Runner tables.
These Foot Rails contain 2 openings to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit).
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNP011T - Nissan Patrol/Armada Y62 (2010-Current)SlimlineIIRoof Rack Kit - by Front Runner
Consisting of:
1 x FANP001 - Nissan Patrol/Armada Y62 (2010-Current) Foot Rails - by Front Runner
1 x RRSTG11 - Slimline II Tray - 1345mm(W) X 2166mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 39kg (86lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 455mm (18")
Length 1615mm (64")
Height 240mm (9")
Shipping Weight:
Weight: 45.2kg (99.4lbs)
Front Runner
FRONT RUNNER Nissan X-Trail/Rogue (2023-Current) Slimline Ii Roof Rack Kit - KRNX007T
$1,314.00
$1,460.00
Unleash a world of adventure for your Nissan X-Trail/Rogue when you fit Front Runner’s tough Slimline II Roof Rack Kit. You can now access 55+ accessories made for this reliable rack system. Carrying your sports or camping gear has never been easier.
This 1358mm/53.5” long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan X-Trail/Rogue. It easily installs using the existing factory mounting points. No drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
WARNING Cancer or Reproductive Harm www.P65Warnings.ca.gov
Consisting of:1x FANX003 - Nissan X-Trail (23-Current) Foot Rail1x RRSTA07 - SLII Tray - 1165mm(W)X1358mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 22.16kg (48.85lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 565mm (22")Length: 1720mm (68")Height: 160mm (6")Shipping Weight:Weight: 26kg (57lbs)
Front Runner
FRONT RUNNER Nissan Xterra N50 Slimline Ii Roof Rack Kit - KRNX005T
$1,898.10
$2,109.00
This 1964mm/77.3" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Nissan Xterra N50. It easily installs using the existing factory mounting points. No drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables.
These Foot Rails contain 1 opening to access a Front Runner under rack mount table (1 smaller Pro Stainless Steel Prep Table Kit or 1 larger Pro Stainless Steel Camp Table Kit).
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRNX005T - Nissan Xterra N50 Slimline II Roof Rack Kit - by Front Runner
Consisting of:
1 x FANX002 - Nissan Xterra N50 Foot Rails - by Front Runner
1 x RRSTA10 - Slimline II Tray - 1165mm(W) X 1964mm(L) - by Front Runner
Material used:
Black epoxy powder-coated T6 aluminium
High strength steel
Approximate Installed Weight: 32kg (69lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width 450mm (18")
Length 1615mm (64")
Height 140mm (6")
Shipping Weight:
Weight 36.6kg (80.6lbs)
Front Runner
FRONT RUNNER Osram Led Light Mx240-Cb/ Mx260-Cb/ Mx180-Cb/ Mx250-Cb Mounting Bolt Kit - RRAC931
$6.30
$7.00
Universal brackets that fit onto the Front Runner Slimline II Roof Rack's side profile, allowing you to mount accessories to your roof rack without having to drill into it.
Features
Consists of:
Comes in a set of (3) three brackets with pre-cut mounting holes. Washers, bolts and nuts included.
Materials used:
Black powder coated steel.
Product Dimensions:
L 115mm (4.52") W 90mm (3.54") x H 55mm (2.16")
Weight:
0.66kg (1.455lbs)
Front Runner
FRONT RUNNER Peugeot Boxer (L1H1/118In Wb/Low Roof) (2014-Current) Slimpro Van Rack Kit - KVPB001T
$2,101.50
$2,335.00
Compatible with Peugeot Boxer (L1H1/118" WB) (2014-Current) low roof vans with a vehicle length of 4963mm / 195.4".
Load-carrying area: 2570mm (101.2") x 1565mm (61.6").
Six (6) Mounting Feet secure into van's existing factory mounting points.
Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5").
Compatible with most Front Runner side mount accessories.
Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories.
Fitment guide and all mounting hardware are included. No drilling or modification required.
All Front Runner racks are backed by a limited lifetime warranty.*
Features
KVPB001T - Peugeot Boxer (L1H1/118" WB/Low Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner
Consisting of:
3x FAVF002 - FPCR Foot Set - by Front Runner
1x RRAC207 - Van Rack Joiner Kit
2x RRAC208 - Van Rack Side Profile End Caps
4x RRNS1475 - Narrow Slat / 1475mm (Pair)
1x SPVT001 - Van Rack Side Profile / 1156mm
1x SPVT002 - Van Rack Side Profile / 1358mm
1x WDST013 - Wind Deflector Van Rack 30mm Lip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
2570mm (101.2") L x 1565mm (61.6") W x 127mm (5") H
Approximate Installed Weight: 30.99kg (68.32lbs)
Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom.
Shipping Dimensions:
Width: 300mm (12")
Length: 1805mm (71")
Height: 195mm (8")
Shipping Weight:
Weight: 35.35kg (78lbs)
Front Runner
FRONT RUNNER Peugeot Boxer (L2H1/136In Wb/Low Roof) (2014-Current) Slimpro Van Rack Kit - KVPB002T
$2,173.50
$2,415.00
Compatible with Peugeot Boxer (L2H1/136" WB) 2014-Current low roof vans with a vehicle length of 5413mm / 213.1".
Load-carrying area: 2974mm (117.1") x 1565mm (61.6").
Six (6) Mounting Feet secure into van's existing factory mounting points.
Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5").
Compatible with most Front Runner accessories.
Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories.
Fitment guide and all mounting hardware are included. No drilling or modification required.
All Front Runner racks are backed by a limited lifetime warranty.*
Features
KVPB002T - Peugeot Boxer (L2H1/136" WB/Low Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner
Consisting of:
3x FAVF002 - FPCR Foot Set - by Front Runner
1x RRAC207 - Van Rack Joiner Kit
2x RRAC208 - Van Rack Side Profile End Caps
4x RRNS1475 - Narrow Slat / 1475mm (Pair)
1x SPVT002 - Van Rack Side Profile / 1358mm
1x SPVT003 - Van Rack Side Profile / 1560mm
1x WDST013 - Wind Deflector Van Rack 30mm Lip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 31.49kg (69.42lbs)
Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom.
Shipping Dimensions:
Width: 300mm (12")
Length: 1805mm (71")
Height: 195mm (8")
Shipping Weight:
Weight: 37.35kg (82lbs)
Front Runner
FRONT RUNNER Peugeot Boxer (L2H2/136In Wb/High Roof) (2014-Current) Slimpro Van Rack Kit - KVPB003T
$2,173.50
$2,415.00
Compatible with Peugeot Boxer (L2H2/136" WB) (2014-Current) High roof vans with a vehicle length of 5413mm / 213.1".
Load-carrying area: 2974mm (117.1") x 1565mm (61.6").
Six (6) Mounting Feet secure into van's existing factory mounting points.
Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5").
Compatible with most Front Runner accessories.
Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories.
Fitment guide and all mounting hardware are included. No drilling or modification required.
All Front Runner racks are backed by a limited lifetime warranty.*
Features
KVPB003T - Peugeot Boxer (L2H2/136" WB/High Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner
Consisting of:
3x FAVF002 - FPCR Foot Set - by Front Runner
1x RRAC207 - Van Rack Joiner Kit
2x RRAC208 - Van Rack Side Profile End Caps
4x RRNS1475 - Narrow Slat / 1475mm (Pair)
1x SPVT002 - Van Rack Side Profile / 1358mm
1x SPVT003 - Van Rack Side Profile / 1560mm
1x WDST013 - Wind Deflector Van Rack 30mm Lip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
2974mm (117.1") L x 1565mm (61.6") W x 127mm (5") H
Approximate Installed Weight: 31.49kg (69.42lbs)
Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom.
Shipping Dimensions:
Width: 300mm (12")
Length: 1805mm (71")
Height: 195mm (8")
Shipping Weight:
Weight: 37.35kg (82lbs)
Front Runner
FRONT RUNNER Peugeot Boxer (L3H2/159In Wb/High Roof) (2014-Current) Slimpro Van Rack Kit - KVPB004T
$2,692.80
$2,992.00
Compatible with Peugeot Boxer (L3H2/159" WB) (2014-Current) high roof vans with a vehicle length of 5998mm / 236.1".
Load-carrying area: 3580mm (141") x 1565mm (61.6").
Eight (8) Mounting Feet secure into van's existing factory mounting points.
Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5").
Compatible with most Front Runner accessories.
Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories.
Fitment guide and all mounting hardware are included. No drilling or modification required.
All Front Runner racks are backed by a limited lifetime warranty.*
Features
KVPB004T - Peugeot Boxer (L3H2/159" WB/High Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner
Consisting of:
4x FAVF002 - FPCR Foot Set - by Front Runner
1x RRAC207 - Van Rack Joiner Kit
2x RRAC208 - Van Rack Side Profile End Caps
5x RRNS1475 - Narrow Slat / 1475mm (Pair)
2x SPVT004 - Van Rack Side Profile / 1762mm
1x WDST013 - Wind Deflector Van Rack 30mm Lip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
3580mm (141") L x 1565mm (61.6") W x 127mm (5") H
Approximate Installed Weight: 40.94kg (90.26lbs)
Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom.
Shipping Dimensions:
Width: 300mm (12")
Length: 1805mm (71")
Height: 195mm (8")
Shipping Weight:
Weight: 44.35kg (98lbs)
Front Runner
FRONT RUNNER Peugeot Boxer (L4H2/159In Wb/High Roof) (2014-Current) Slimpro Van Rack Kit - KVPB005T
$2,837.70
$3,153.00
Compatible with Peugeot Boxer (L4H2/159" WB) (2014-Current) high roof vans with a vehicle length of 6363mm / 250.5".
Load-carrying area: 3928mm (154.6") x 1565mm (61.6").
Ten (10) Mounting Feet secure into van's existing factory mounting points.
Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5").
Compatible with most Front Runner accessories.
Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories.
Fitment guide and all mounting hardware are included. No drilling or modification required.
All Front Runner racks are backed by a limited lifetime warranty.*
Features
KVPB005T - Peugeot Boxer (L4H2/159" WB/High Roof) (2014-Current) Slimpro Van Rack Kit - by Front Runner
Consisting of:
5x FAVF002 - FPCR Foot Set - by Front Runner
2x RRAC207 - Van Rack Joiner Kit
2x RRAC208 - Van Rack Side Profile End Caps
5x RRNS1475 - Narrow Slat / 1475mm (Pair)
1x SPVT001 - Van Rack Side Profile / 1156mm
2x SPVT002 - Van Rack Side Profile / 1358mm
1x WDST013 - Wind Deflector Van Rack 30mm Lip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
3928mm (154.6") L x 1565mm (61.6") W x 127mm (5") H
Approximate Installed Weight: 42.17kg (92.97lbs)
Peugeot Boxer Van Rack Kit heights are adjustable from 80mm (Z bracket inverted) to 130mm (Z bracket standard mounting) all measurements are taken from bottom of roof ditch to top of the rack slat.The slat T slots and side profiles take standard M8 hex bolts top and bottom.
Shipping Dimensions:
Width: 300mm (12")
Length: 1805mm (71")
Height: 195mm (8")
Shipping Weight:
Weight: 43.35kg (95lbs)
Front Runner
FRONT RUNNER Pickup Egr Rolltrac Slimline Ii Load Bed Rack Kit / 1425(W) X 1358(L) - KRRT033T
$1,680.30
$1,867.00
This kit creates a full-size rack that sits above your Pickup's load bed when fitted with a EGR RollTrac cover. This Slimline II cargo carrying rack kit contains the Slimline II tray (1425mm x 1358mm) and 6 Pickup Roll Top Leg Mounts that fit into the existing EGR RollTrac channels.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: This rack kit is not suitable for the Volkswagen Amarok. If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRRT033T - Pickup EGR RollTrac Slimline II Load Bed Rack Kit / 1425(W) x 1358(L) - by Front Runner
Consisting of:
3x LASS028 - Pick-Up Roll Top Leg Mount
1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 29.29kg (64.57lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 445mm (18")
Length: 1730mm (68")
Height: 195mm (8")
Shipping Weight:
Weight: 28kg (62lbs)
Front Runner
FRONT RUNNER Pickup Load Bed 5.5' Canopy/Cap/Trailer Slimsport Rack Kit - KSCA001
$867.60
$964.00
This Slimsport Kit is suited for truck canopies/camper shells/caps.
This low profile flat deck Slimsport rack has a load carrying area of 1350mm (53.1") x 1211mm (47.7").
The sleek side rails have integrated mounting feet. Mounting feet also have additional brace brackets for added strength.
The high-strength aluminum slats have top and bottom T-slots suitable for all Front Runner top mount accessories.
Easily add on the Rack Accessory Mounting Bracket Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner (sold separately) for all Front Runner side mount accessories.
Fitment guide and all mounting hardware included.
Note: Drilling required.
Note: Under Rack Tables are not compatible with the Slimsport rack kit range
Features
KSCA001 - Pickup Load Bed 5.5'Canopy/Cap/Trailer Slimsport Rack Kit
Consisting of:
1 x Pickup Load Bed 5.5'Canopy/Cap/Trailer Slimsport Tray
1 x Installation Hardware
1 x Fitting Instructions
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
1350mm (53.1") L x 1211mm (47.7") W x 63mm (2.5") H
Approximate Installed Weight: 16.99kg (37.46lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof.
Shipping Dimensions:
Width: 240mm (9")
Length: 1560mm (61")
Height: 100mm (4")
Shipping Weight:
Weight: 17.17kg (38lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger 1000 Crew Cab (2018-Current) Slimsport Roof Rack Kit - KSPR003T
$1,239.30
$1,377.00
This low-profile flat deck Slimsport rack has a load-carrying area of 1559mm (61.4") L x 1238mm (48.7") W.
The sleek side rails have integrated mounting feet. The mounting feet also have additional brace brackets for added strength.
The high-strength aluminum slats have T-slots suitable for all Front Runner top mount accessories.
Easily add on the Rack Accessory Mounting Bracket Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner for most Front Runner side mount accessories (sold separately).
The included standard full fairing with rubber edge trim makes the rack ultra-quiet.
Need a lightbar? The optional lightbar fairing Polaris Ranger UTV (2018-Current) Slimsport Rack 40" Light Bar Wind Fairing (sold separately) has a 40" cutout to allow use of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount (sold separately).
Fitment guide and all mounting hardware included.
6"/T30 Torx Allen Key for Slimsport Rack 6"/T30 Torx Allen Key for Slimsport Rack is required for installation.
Note: Drilling required.
Note: Under Rack Tables are not compatible with the Slimsport rack kit range
Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets.
Features
KSPR003T - Polaris Ranger Crew Cab (2018-Current) Slimsport Roof Rack Kit
Consisting of:
1x KSPR002 - Polaris Ranger Crew Cab (2018 - Current) Slimsport
1x RRAC243 - Polaris Ranger Crew Cab(18-Curr)Ssport WindFairing
1x RRAC971 - Protection Strip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
1577mm(62.1") L x 1244mm(49") W x 184mm(7.2") H
Approximate Installed Weight: 23.01kg (50.73lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof.
Shipping Dimensions:
Width: 330mm (13")
Length: 1696mm (67")
Height: 210mm (8")
Shipping Weight:
Weight: 27.38kg (60lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger 1000 Crew Cab (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready - KSPR004T
$1,239.30
$1,377.00
This low-profile flat deck Slimsport rack has a load carrying area of 1559mm (61.4") L x 1238mm (48.7")W.
The sleek side rails have integrated mounting feet. The mounting feet also have additional brace brackets for added strength.
The high-strength aluminum slats have T-slots suitable for all Front Runner top mount accessories.
Easily add on the Rack Accessory Mounting Bracket Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner for most Front Runner side mount accessories (sold separately).
Included in the Polaris Ranger UTV (2018-Current) Slimsport Rack 40" Light Bar Wind Fairing has a 40" cutout to allow the use of the Front Runner 40 LED Slim Light Bar 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount (sold separately).
Fitment guide and all mounting hardware included.
6"/T30 Torx Allen Key for Slimsport Rack is required for installation (sold separately).
Note: Drilling required for installation.
Note: Under Rack Tables and some side mount accessories such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets are not compatible with the Slimsport rack kit range.
Features
KSPR004T - Polaris Ranger Crew Cab (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready
Consisting of:
1x KSPR002 - Polaris Ranger Crew Cab (2018 - Current) Slimsport
1x RRAC242 - Polaris Ranger UTV(18-Curr)Ssport L-BarWindFairing
1x RRAC971 - Protection Strip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
1577mm(62.1") L x 1244mm(49") W x 184mm(7.2") H
Approximate Installed Weight: 24.1kg (53.13lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof.
Shipping Dimensions:
Width: 330mm (13")
Length: 1696mm (67")
Height: 210mm (8")
Shipping Weight:
Weight: 27.18kg (60lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger Crew Cab (2018-Current) Slimsport Rack Wind Fairing - RRAC243
$146.70
$163.00
Lightbar wind fairing for Polaris Ranger UTV (2018-Current) Slimsport Roof Rack Kit and Polaris Ranger Crew Cab (2018-Current) Slimsport Roof Rack Kit.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Features
Consists of:
1 x Slimsport Rack Wind Fairing
1 x Protection Strip
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel
Product Dimensions:
1238mm (48.7") L x 144mm (5.7") W x 136mm (5.4") H
Weight:
2.96kg (6.5lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger Slimline Ii Load Bed Rack Kit - KRPR002T
$1,422.90
$1,581.00
This kit creates a full-size rack that sits above your Polaris Ranger load bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1345mm x 752mm) and 4 Pickup Truck Bed Universal Legs that fit into the Load Bed Mount.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation.
Features
KRPR002T - Polaris Ranger Slimline II Load Bed Rack Kit
Consisting of:
2x LASS028 - Pick-Up Roll Top Leg Mount
1x LASS043 - Polaris Ranger Load Bed Mount
1x RRSTG04 - SLII Tray - 1345mm(W)X752mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 24.9kg (54.9lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 445mm (18")
Length: 1720mm (68")
Height: 265mm (10")
Shipping Weight:
Weight: 31kg (68lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger Utv (2018-Current) Slimsport Rack 40In Light Bar Wind Fairing - RRAC242
$146.70
$163.00
Lightbar wind fairing for Polaris Ranger UTV (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready and Polaris Ranger Crew Cab (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready.
Allows fitment of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount.
Air flows easily over the rack and accessories, reducing drag and wind noise.
Helps fuel consumption while carrying bulky loads.
A durable rubber blade is fitted to the bottom edge of the Wind Fairing to help seal any gaps and act as a roof guard when traveling over rough terrain.
Brackets and installation hardware included.
Features
Consists of:
1 x Polaris Ranger Slimsport Rack 40" Light Bar Wind Fairing
1 x Protection Strip
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel
Product Dimensions:
1237mm (48.7") L x 144mm (5.7") W x 127mm (5") H
Weight:
3.6kg (7.9lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger Utv (2018-Current) Slimsport Roof Rack Kit - KSPR001T
$753.30
$837.00
This low-profile flat deck Slimsport rack has a load-carrying area of 749mm (29.5") x 1238mm (48.7").
The sleek side rails have integrated mounting feet. The mounting feet also have additional brace brackets for added strength.
The high-strength aluminum slats have T-slots suitable for all Front Runner top mount accessories.
Easily add on the Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner for most Front Runner side mount accessories (sold separately).
The included standard full fairing with rubber edge trim makes the rack ultra-quiet.
Need a lightbar? The optional lightbar fairing Polaris Ranger UTV (2018-Current) Slimsport Rack 40" Light Bar Wind Fairing (sold separately) has a 40" cutout to allow use of 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount (sold separately).
Fitment guide and all mounting hardware included.
6"/T30 Torx Allen Key for Slimsport Rack is required for installation.
Note: Drilling required.
Note: Under Rack Tables are not compatible with the Slimsport rack kit range
Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets.
Features
KSPR001T - Polaris Ranger UTV (2018-Current) Slimsport Roof Rack Kit
Consisting of:
1x KSPR001 - Polaris Ranger UTV (2018-Current) Slimsport Roof R
1x RRAC243 - Polaris Ranger Crew Cab(18-Curr)Ssport WindFairing
1x RRAC971 - Protection Strip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Dimensions:
749mm (29.5") L x 1238mm (48.7") W x 157mm (6.2") H
Approximate Installed Weight: 15.84kg (34.92lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof.
Shipping Dimensions:
Width: 250mm (10")
Length: 1560mm (61")
Height: 140mm (6")
Shipping Weight:
Weight: 15.6kg (34lbs)
Front Runner
FRONT RUNNER Polaris Ford Ranger Utv (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready - KSPR002T
$753.30
$837.00
This low-profile flat deck Slimsport rack has a load carrying area of 749mm (29.5") x 1238mm (48.7").
The sleek side rails have integrated mounting feet. The mounting feet also have additional brace brackets for added strength.
The high-strength aluminum slats have T-slots suitable for all Front Runner top mount accessories.
Easily add on the Slimsport/Slimpro Van Side Mount Accessory Bracket / Small by Front Runner for most Front Runner side mount accessories (sold separately).
Included in the Polaris Ranger UTV (2018-Current) Slimsport Rack 40" Light Bar Wind Fairing has a 40" cutout to allow the use of the 40" LED Slim Light Bar VX1000-CB SM / 12V/24V / Single Mount (sold separately).
Fitment guide and all mounting hardware included.
6"/T30 Torx Allen Key for Slimsport Rack is required for installation (sold separately).
Note: Drilling required for installation.
Note: Under Rack Tables and some side mount accessories such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets are not compatible with the Slimsport rack kit range.
Features
KSPR002T - Polaris Ranger UTV (2018-Current) Slimsport Roof Rack Kit / Lightbar Ready
Consisting of:
1x KSPR001 - Polaris Ranger UTV (2018-Current) Slimsport Roof R
1x RRAC242 - Polaris Ranger UTV(18-Curr)Ssport L-BarWindFairing
1x RRAC971 - Protection Strip
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Assembled Rack Kit Dimensions:
767mm(30.2") L x 1244mm(49") W x 158mm(6.2") H
Approximate Installed Weight: 13.5kg (29.76lbs)
The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimsport Rack add 60mm-70mm (2.4"-2.8") to the highest point of your roof.
Shipping Dimensions:
Width: 250mm (10")
Length: 1560mm (61")
Height: 140mm (6")
Shipping Weight:
Weight: 15.4kg (34lbs)
Front Runner
FRONT RUNNER Porsche 911 (997 Model) Slimline Ii Roof Rack Kit - KRPN002T
$1,005.30
$1,117.00
The powerful Porsche 911 has little gear-carrying carrying capacity unless you fit Front Runner's modular Slimline II Roof Rack Kit. The Wind Deflector will help to minimize rack noise, while the tray is the perfect place to put extra cargo, your spare wheel or other gear.
This 954mm/37.6" long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 4 Foot Rails to mount the Slimline II Tray to your Porsche 911. It easily installs using the existing factory mounting points. No drilling required.All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRPN002T - Porsche 911 (997 Model) Slimline II Roof Rack Kit
Consisting of:
1x FAPN001 - Porsche 911(997 Model) Mounting Bracket
1x RRSTA05 - SLII Tray - 1165mm(W)X954mm(L)
Material Used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 16.8kg (37.04lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicle's roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 445mm (18")
Length: 1720mm (68")
Height: 290mm (11")
Shipping Weight:
Weight: 23kg (51lbs)
Front Runner
FRONT RUNNER Porsche 924 Slimline Ii Roof Rack Kit - KRPN001T
$1,182.60
$1,314.00
This 954mm/37.6" long, full-size, Slimline II cargo carrying roof rack kit for the Porsche 924 contains the Slimline II Tray and Wind Deflector, as well as 4 Gutter Mount Legs for mounting the Tray to the vehicle. Installs easily with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Note: This Kit requires the vehicle to have protruding side gutters to be fitted. If unsure of fitment, please contact Front Runner Support.
Features
KRPN001T - Porsche 924 Slimline II Roof Rack Kit - by Front Runner
Consisting of:
2x LASD102 - No 2 Leg Diagonal 130mm (Pair)2x RRAC034 - Inter-Slat Bracket1x RRSTA05 - SLII Tray - 1165mm(W)X954mm(L)
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 22.54kg (49.69lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 440mm (17"); Length: 1730mm (68"); Height: 260mm (10")
Shipping Weight:
Weight: 43.4kg (95lbs)
Front Runner
FRONT RUNNER Porsche Cayenne (2002-2010) Slimline Ii Roof Rack Kit - KRPC001T
$1,189.80
$1,322.00
This 1358mm/53.5" long full-size Slimline II cargo carrying roof rack kit for the Porsche Cayenne contains Slimline II Tray, Wind Deflector and 4 Feet. Installs easily to factory/OEM tracks with no drilling required.
All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.
All Front Runner Racks are backed by a Limited Lifetime Warranty*
Features
KRPC001T - Porsche Cayenne (2002-2010) Slimline II Roof Rack Kit - by Front Runner
Consisting of:
2 x FASS013 - Foot Set / 60mm-70mm - by Front Runner
2 x RRAC907 - Stud Plate MB Sprinter Track
1 x RRSTA07 - Slimline II Tray - 1165mm(W) X 1358mm(L) - by Front Runner
Material used:
Black epoxy powder - coated T6 aluminium
High strength steel
Approximate Installed Weight: 22.8kg (50.3lbs)
The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.
To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot, Grab-on Foot or Strap-On Foot listed above.
If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters.
If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.
Shipping Dimensions:
Width: 450mm (18.0")
Length: 1615mm (64.0")
Height: 140mm (6.0")
Shipping Weight:
25.3kg (56.0lbs)
Front Runner
FRONT RUNNER Potjie Pot/Dutch Oven And Carrier - RRAC081
$316.80
$352.00
Theres no better place to keep potentially hot, grimy, dirty, and cumbersome camp kitchen supplies than up and out of the way, outside the vehicle.
The Front Runner Potjie Pot Carrier offers a sensible way to travel with a potjie pot.
The potjie pot is secured in the bracket by the three legs. The supplied ratchet strap threads through the lid of the pot and fixes points on the bracket.
The #3 cast iron pot holds 7.8L / 2.1 Gallons. The round shape and cast iron allows the heat to flow evenly around the sides and maintain liquids at the lowest point to keep them from burning. The lid has a deep lip for holding hot coals.
The high strength steel carrier is finished with the same durable, weather resistant powder coating as the Front Runner Slimline II Rack.
Like all Front Runner rack accessories, the installation is simple. Just slide the bolts into the t-slots of any Front Runner Rack Tray, set down the carrier, then add nuts and tighten.
Features
Consists of:
Rack mounted bracket
Strap guide
Ratchet strap
mounting hardware
No 3 cast iron pot
Materials used:
Black powder-coated high strength steel
Nylon strap
Cast iron pot
Product Dimensions:
280mm (11") W x 280mm (11") D x 343mm (13.5") H
Pot Specifications:
No. 3 potjie Pot - 7.8l (2.1gal) capacity
Max outer diameter: 290mm (11.4")
Height: 300mm (11.8")
Lid max outer diameter: 260mm (10.2")
Total Weight:
11.25kg (24.9lbs)
Front Runner
FRONT RUNNER Potjie Pot/Dutch Oven Carrier - RRAC062
$110.70
$123.00
Create deliciously hearty meals out in the wilderness, fit for the avid explorer and overlanding veterans alike.
The Front Runner Potjie Pot/Dutch Oven Carrier is a safe and durable means of transporting your potjie pot/dutch oven where ever your travels may take you.
The potjie pot/dutch oven is placed centrally into the bracket with the three legs fitting into the holes in the three protrusions extending from the centre of the bracket. The supplied ratchet strap threads through the lid of the pot and fixes to pre-drilled points on the bracket.
Made of corrosion resistant steel and black powder-coated with an industry preferred, outdoor rated coating.
Features
Consists of:
Potjie bracket for No 2 & No 3 pot
Ratchet strap
Mounting hardware
Materials used:
Black powder-coated steel
Product Dimensions:
276mm (10.9") L x 229mm (9") W x 133mm (5.2") H
Weight:
2kg (4.4lbs)
Front Runner
FRONT RUNNER Pro Bed Rack Headache Molle Panel - PBAC002
$65.70
$73.00
Store and transport adventure gear and supplies with the innovative Pro Bed Rack Headache Molle Panel. It securely bolts to the Pro Bed System, behind your vehicle's cab and features variety of molle webbing for attaching your gear. This includes straps, bags, and other accessories. The panel is also removable for easy cleaning.
Securely bolts to the Pro Bed System, behind your vehicle's cab.
Easily access your adventure gear and additional supplies when strapped to the Pro Bed Rack Headache Molle Panel.
Made of high-strength steel and sealed in the same durable black powder coating as the Front Runner Pro Bed System.
Features
Consists of:
1 x Molle Panel
1 x Mounting Bracket
Hardware Kit
Fitting Instructions
Material used:
Black powder coated high strength steel
Product Dimensions:
485mm (19.1") H x 630mm (24.8") W x 2mm (0.1") D
Weight:
1.8kg (4lbs)
Front Runner
FRONT RUNNER Pro Bed Rack Side Molle Panel / 1200Mm - PBAC012
$135.00
$150.00
Add this strong, steel Side Molle Panel to make your Pro Bed Rack even more versatile. This 1200mm/47.2" long, Molle Panel easily slides into the side extrusions to create that extra storage space we all need. A great place to put gear you might need in a hurry.
This Pro Bed Rack Side Molle Panel creates even more storage space to attach various accessories to the outside of the bed rack for easy access.
It fits onto the sides of the Pro Bed Rack by sliding into the side extrusions. No drilling is required.
Made of high-strength steel and sealed in the same durable black powder coating as the Front Runner rack.
Features
Consists of:
4 x Molle Panel
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel
Product Dimensions:
1200mm (47.2") L x 30mm (1.18") W x 496mm (19.53") H
Weight:
7.7kg (17lbs)
Front Runner
FRONT RUNNER Pro Bed Rack Side Molle Panel / 1400Mm - PBAC013
$150.30
$167.00
Add this strong, steel Side Molle Panel to make your Pro Bed Rack even more versatile. This 1400mm/55.1" long, Molle Panel easily slides into the side extrusions to create that extra storage space we all need. A great place to put gear you might need in a hurry.
This Pro Bed Rack Side Molle Panel creates even more storage space to attach various accessories to the outside of the bed rack for easy access.
It fits onto the sides of the Pro Bed Rack by sliding into the side extrusions. No drilling is required.
Made of high-strength steel and sealed in the same durable black powder coating as the Front Runner rack.
Features
Consists of:
4 x Molle Panel
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel
Product Dimensions:
1400mm (55.12") L x 30mm (1.18") W x 496mm (19.53") H
Weight:
9.2kg (20.3lbs)
Front Runner
FRONT RUNNER Pro Bed Recovery Bracket - PBAC010
$154.80
$172.00
When stuck, you want quick access to your recovery boards. This is exactly what the Pro Bed Recovery Bracket offers, allowing you to conveniently attach your MAXTRAX, Tred Pro or Tred GT to the Pro Bed System.
This Pro Bed Recovery Bracket bolts on the top and bottom side of the Pro Bed System.
To attach your MAXTRAX, use the included Pro Bed Recovery Device Mounting Hardware or MAXTRAX Mounting Pin Set * Sold Separately.
The included Pro Bed Recovery Device Mounting Hardware can be used to mount your Tred Pro and Tred GT Recovery Boards.
Mounting holes could be used mount other accessories to your Pro Bed System or Pro Bed Rack Kit.
As a universal solution, the Pro Bed Universal Accessory Mount is available.
For a complete water solution, Front Runner offers the Pro Bed Water Kit / 20L.
Made of high strength steel and coated in the same durable, weather-resistant black powder coating as the Front Runner Rack.
Features
Consists of:
1 x Pro Bed Universal Accessory Mount
1 x Pro Bed Recovery Device Mounting Hardware
Installation Hardware
Fitment Guide
Materials used:
Black powder coated steel
Product Dimensions:
490mm (19.3") L x 200mm (7.9") W x 30mm (1.9") H (Per Single Bracket)
Weight:
3.28kg (7.2lbs)
Front Runner
FRONT RUNNER Pro Bed Recovery Device Mounting Hardware - PBAC009
$65.70
$73.00
Just because you've installed the impressive Pro Bed Rack System doesn't guarantee you can't get stuck in the mud or water. This is why you need the Pro Bed Recovery Device Mounting Hardware to attach your recovery boards to the Pro Bed System. This means you can also quickly access them if needed. This system will work with MAXTRAX, TRED GT or TRED PRO recovery boards.
A hardware kit used to mount 1 or 2 pairs of MAXTRAX, TRED GT & TRED PRO to the Pro Bed Universal Accessory Mount.
Contains:
4 x M10 x 100 Hex Bolt
4 x M10 x 60 Hex Bolt
4 x M10 x 30 x 3 SS Flat Washer
4 x M10 Eye Nut
4 x M10 Nylock Nut
Features
Consists of:
4 x M10 x 100 Hex Bolt
4 x M10 x 60 Hex Bolt
4 x M10 x 30 x 3 SS Flat Washer
4 x M10 Eye Nut
4 x M10 Nylock Nut
Materials used:
Black powder-coated high strength steel
Weight:
0.78kg (1.7lbs)
Front Runner
FRONT RUNNER Pro Bed Tailgate Net - PBAC004
$54.00
$60.00
This Pro Bed Tailgate Net is a cargo saver that stops everything in your load bed from sliding out the back. It easily attaches to the integrated fixing points on the back of the Pro Bed System and Pro Bed Rack Rack Kits. It's a great way to ensure your gear stays where it should be.
The Pro Bed Tailgate Net attaches to the integrated fixing points on the back of the Pro Bed System and Pro Bed Rack Kits.
Designed to prevents items from sliding out the rear of the Load Bed.
Adjustable to securely fit all Pro Bed System and Pro Bed Rack Kits.
Made from high tensile polyester webbing with high quality buckles.
WARNING Cancer or Reproductive Harm www.P65Warnings.ca.gov
Consists of:1 x Cargo Net
Materials used:High Tenacity Polyester NetPolyacetal Buckles
Product Dimensions:2077mm (81.8") L x 620mm (24.4") W
Weight:0.5kg (1.1lbs)
Front Runner
FRONT RUNNER Pro Bed Universal Accessory Mount - PBAC006
$89.10
$99.00
When mounting accessories to your smart Pro Bed System, you will first need this Pro Bed Universal Accessory Mount. Once in place, this mount will happily accommodate any accessory as a universal solution.
This Pro Bed Rack Universal Accessory Mount bolts on the top and bottom side of the Pro Bed System.
Mounting holes are used mount accessories to your Pro Bed System or Pro Bed Rack Kit.
As a recovery solution, the Pro Bed Recovery Bracket is available.
As a water solution, Front Runner offers the Pro Bed Water Kit / 20L.
Made of high strength steel and coated in the same durable, weather-resistant black powder coating as the Front Runner Rack.
Features
Consists of:
2 x Mounting Brackets
Hardware Kit
Fitting Instructions
Materials used:
Black powder coated high strength steel
Product Dimensions:
490mm (19.3") L x 200mm (7.9") W x 30mm (1.9") H (Per Single Bracket)
Weight:
2.53 kg (5.6 lbs)
Front Runner
FRONT RUNNER Pro Bed Water Kit / 20L - PBAC011
$350.10
$389.00
Water must be easily accessible when on the road in your rig. That is exactly what the lockable Pro Bed Water Kit offers, as it attaches to the side of your Pro Bed System, 20 litres of water at your disposal.
This Pro Bed Water Kit / 20L bolts on the side of the Pro Bed System.
Install this mount onto your Pro Bed System to allow quick and easy access to your 20L Pro Water Tank.
Easily remove your water tank by loosening the stainless-steel eye nuts.
The water tank can be locked for added peace of mind using the Rack Accessory Lock / Small (sold separately).
Plastic alignment spacers protect, align and secure your water tank.
Mounting holes could be used mount other accessories to your Pro Bed System or Pro Bed Rack Kit.
As a recovery solution, the Pro Bed Recovery Bracket is available.
Made of high strength steel and coated in the same durable, weather-resistant black powder coating as the Front Runner Rack.
Features
Consists of:
1 x Pro Bed Universal Accessory Mount
1 x Universal Side Mount for Pro Water Tank / 20L
1 x Pro Water Tank With Tap / 20L
Installation Hardware
Fitment Guide
Materials used:
Black powder coated steel
Food grade BPA free polyethylene Water Tank
Assembled Product Dimensions:
470mm (18.5") L x 224mm (8.8") W x 490mm (19.3") H
Weight:
6.82kg (15lbs)
Front Runner
FRONT RUNNER Pro Bike Carrier - RRAC148
$819.00
$910.00
Easily install onto your Front Runner Rack in minutes.
No front wheel removal necessary.
Suitable for all bike sizes; all frame styles including composite carbon frames; all thru axle and brake configurations as well as Lefty forks and full suspension bikes.
Front wheel holder is easily adjusted and holds the bike steady while the rear Wheel Holder is secured.
Adjustable to secure most wheel diameters including road bikes, MTB and fat bikes with tire widths ranging from 18mm/0.7" up to 132mm/5.2".
The carrier folds flat and secures onto your rack when not in use.
Bike can be locked using Rack Accessory Lock / Large.
Constructed with same weather resistant stainless steel and powder coating as the Front Runner racks and mounting systems.
Features
Consists of:
1 x Bike Carrier
1 x Bike Carrier Rack Clamp
1 x Rear Wheel Holder
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel
Plastic
Product Dimensions:
Bike Carrier (Closed):
825mm (32.5") L x 205mm (8.1") W x 100mm (3.9") H
Rear Wheel Holder:
230mm (9.1") L x 170mm (6.7") W x 70mm (2.8") H
Weight:
9.4kg(20.7lbs)
Special Notes:
Suitable for all bike sizes incl. Fat Bikes
Front Runner
FRONT RUNNER Pro Canoe / Kayak / Sup Carrier - RRAC137
$652.50
$725.00
Fits most size canoes, kayaks, SUPs and surf skis. The space between the brackets is only limited by the length of your Front Runner Roof Rack or distance between your Load Bars.
Highly adjustable brackets allow for multiple mounting angles for your canoe, kayak or SUP.
The foam-padded holders are self-adjusting for the perfect fit to the hull of your boat.
The dense weather-resistant open cell foam pads are covered with a water-repellent polyester cover that is UV stabilized to prevent fading.
Pads can be easily replaced if damaged in any way.
Toys are secured to the Canoe / Kayak / SUP Carrier using the supplied Front Runner Stratchits straps and eye nuts.
The included Front Runner adjustable and stretchable Stratchits are the perfect tie-down for serious cargo.
The quick and efficient straps will keep loads stable and secure without damaging surfaces and are rated up to 300 lbs.
The Stratchit's clever cinching system creates an easy-on, and easy-off, secure transport every time.
Complete kit includes everything necessary to secure your water toys to Front Runner Roof Racks or Load Bars.
Weight limit: 60kg (132 lbs).
Features
Consists of:
2 x Adjustable Holders
4 x Pads
1 x Pair of Stratchits
4 x Eye nuts
Installation Hardware
Fitting Instructions
Materials used:
Adjustable Holders:
Black powder coated steel
EPE (Expandable Polyethylene) foam Pads:
100% UV protected polyester outer shell
100% polyester lining
Product Dimensions (fully opened):
700mm (27.6") L x 75mm (3") W x 112mm (4.4") H (Single Holder)
Weight:
6.2kg (13.7lbs) (Holder Set)
Front Runner
FRONT RUNNER Pro Canoe And Kayak Carrier Spare Pad Set - RRAC138
$49.50
$55.00
Firm 100% polyethylene open cell foam for long-lasting reliability.
Made with water-resistant and UV protected outdoor grade fabrics.
The heavy-duty Velcro closure system allows for quick attachment or removal.
Pads secure around the Pro Canoe / Kayak / SUP Carrier.
A single carrier bracket provides a wide 600mm / 23.6" surface for a range of uses and extra protection.
Sold in pairs.
Features
Consists of:
2 x Pads
Materials used:
Foam:
100% polyethylene open cell foam
Fabric:
90% Polyester / 10%PVC
Grade-4 UV protection
Product Dimensions:
300mm (11.8") L x 75mm (3") W x 40mm (1.6") H (Single Pad)
Weight:
280g (9.9oz)
Special Notes:
Foam Density: 1.1lb
Foam Max Load: 100kg (220lbs)
Front Runner
FRONT RUNNER Pro Fork Mount Bike Carrier / Power Edition - RRAC189
$122.40
$136.00
Upright bike carrier, made from strong steel and aluminum.
Powder-coated in the same durable finish as the Front Runner rack and load bars for durability.
Front fork clamp features a quick release that fits all standard fork dropouts.
Rear wheel holder can accommodate all wheel sizes and widths from 700c x 23mm road wheels up to 26 x 4.5" fat bike tires.
Quickly secure and adjust the rear wheel with the robust ratcheting buckle and strap.
Note: Fitment to a rack requires a minimum rack length of 1156mm (6 slats).
Note: This solution is not compatible with Boost Hubs/Forks.
Features
Consists of:
1 x Fork Clamp
1 x Rear Wheel Holder
Installation Hardware
Fitting Instructions
Materials used:
Black powder coated steel & aluminum
Rubber ladder strap
Plastic ratchet buckle
Overall Product Dimensions:
300mm (11.8") L x 176mm (6.9") W x 81mm (3.2") H
Rear Holder:
230mm (9.1") L x 176mm (6.9") W x 81mm (3.2") H
Front Clamp:
70mm (2.8") L x 152mm (6") W x 114mm (4.5") H
Weight:
1.6kg (3.5lbs)
Front Runner
FRONT RUNNER Pro Ski, Snowboard And Fishing Rod Carrier - RRAC149
$437.40
$486.00
Easily secure and store longer gear, such as fishing rods, snowboards and skis, with these alligator-grip style holders.
Built to keep your gear safe on, and off, the worlds toughest roads.
Made from corrosion resistant steel and sealed with the same durable, weather rated powder coating as the Front Runner Roof Racks.
The soft 30mm / 1.2 wide rubber grippers clamp tight without harming or scratching the surfaces of your valuable gear in all weather conditions.
Lock your valuable gear in place for extra security. Supplied with 4 keys (3 spare keys).
Each lock features a cover to prevent water ingress and ice forming in colder climates.
The locking mechanism has a ratchet feature to allow easier closing of the holders for gear up to 30mm / 1.2" thick.
A hold open feature allows for easy loading and unloading.
Usable opening size: 495mm / 19.5.
There is a 65mm / 2.6 clearance distance from the top of the rack or load bar slat to the bottom of the snowboard / fishing rod.
A holder set can accommodate two (2) pairs of ski's or one (1) snowboard (two (2) with bindings removed).
All Front Runner Roof Racks can accommodate 2 holders side by side. This allows storage of up to four (4) pairs of skis or two (2) snowboards (four (4) with bindings removed).
Save space on top of your rack and use Recovery Device & Gear Holding Side Brackets* to mount this carrier to the sides of any Front Runner Rack.
*Note: Recovery Device & Gear Holding Side Brackets are sold separately.
Features
Consists of:
2 x Holders
4 x Rubber Grippers
4 x Keys
2 x Brackets for side mount (*requires Recovery Device & Gear Holding Side Brackets not incl.)
Installation Hardware
Materials used:
Black powder coated steel
Rubber
Product Dimensions:
578mm (22.8") L x 49mm (1.9") W x 106mm (4.2") H (Single Holder)
Weight:
2.4kg (5.3lbs) (Single Holder)
4.8kg (10.6lbs) (Per Set)
Optima
Optima Battery D34 YellowTop Deep Cycle 12V AGM 750 CCA
$379.00
$600.00
Optima Battery D34 YellowTop Deep Cycle 12V AGM 750 CCA (Free Postage)
The Yellow Top battery is the result of four decades of technological innovation and engineering. Like Optima's Red Top and Blue Top batteries, the battery features Optima's "Six Pack." The AGM design features spiral cells filled with highly absorbent, fine fiberglass mats.
Handles Heavy Loads
The Yellow Top battery delivers vital power when there are high electrical loads. Sometimes, demand exceeds alternator capacity. It's an excellent choice for vehicles loaded with accessories. For example, the Yellow Top delivers the power needed to meet the demands of an aftermarket audio system with extra amplifiers. When there's a substantial draw of electrical current, the Optima Yellow Top delivers the superior performance you need. Heavy loads often deplete traditional flooded lead-acid batteries to the point that they never recover.
You can also count on the Yellow Top battery to meet regular starting and operational needs.
Excellent No-alternator Solution
The deep-cycle battery is the perfect choice when there is no alternator. For example, competitive racers love the Yellow Top. They use it in ultra-lightweight hill-climb cars, drag cars and motorkhana specials. Also, the Yellow Top is up to 15 times more resistant to vibration than traditional flooded designs. This is a big plus in typical racing conditions. Extreme enthusiasts trust the Yellow Top when a power failure is not an option.
This deep-cycle design offers other important advantages. Count on the Yellow Top to perform across the wide range of Australia's weather extremes. Enjoy the superior performance you require during winters in Melbourne and summers in Sydney.
The Yellow Top battery delivers up to three times the battery life of certain competitors. The maintenance-free design is good for more than 300 discharge and recharge cycles. Better yet, the AGM design is virtually spill-proof. It is possible to mount the Yellow Top in almost any position.
Invest in the Yellow Top, a high-performing AGM battery from Optima, an industry leader in advanced battery technology. Its best-in-class material purity outperforms competing lead alloy models.
The Yellow Top deep-cycle battery delivers reliable power every day and everywhere.
Features
Voltage: 12v
Terminal: SAE
Assembly: LHP
CCA 750
AH 55
L 254 x W 173 x H 199 mm
Deep-cycle and cranking power
Up to 3X longer life
15 times more vibration-resistant
Virtually spillproof
Mountable in virtually any position
Maintenance-free
Faster recharging
Optimal starting power
300+ discharge/recharge cycles
8012-254
TJM
TJM Awning To Suit Allora Rtt - 620ALYRTTAWN (Pick up Only)
$269.01
The TJM Awning is a perfect match for the Allora Aluminium Rooftop Tent, designed to bring added comfort and protection on your outdoor adventures. Constructed from durable 420D Oxford Polyester Fabric, this awning boasts a water column rating of 3000mm, ensuring reliable water resistance even in unpredictable weather. Quick and easy to set up, it offers ample shade, making it ideal for relaxing, or staying dry during unexpected showers. Enhance your rooftop tent experience with the TJM Awning—built tough for the great outdoors.
Specifications
Compatible:
TJM Allora Aluminium Roof Top Tent
Shade Coverage:
Provides up to 7.5m2 of shade
Material:
420D polyester Oxford fabric with 3000mm PU waterproof rating, UPF 50+
Parts Included:
Awning, aluminium telescopic tent poles, ground pegs, guy ropes, and storage bags
Package Weight:
6.50 kg
TJM
TJM Wireless 8 Gang Switch Panel Controller - 032TJM8WSPC
$259.00
Take control of your off-road setup with the ultimate 8-gang wireless switch controller from TJM. Designed for explorers who demand precision and power, this controller lets you command your 4x4’s accessories from up to 60m away. With customizable backlighting, 3 switch modes, and a140 interchangeable legends, you’ll have total control over your adventure. Quick to recharge, ruggedly built, and powerful enough for any job - this isn’t just a controller, it’s your key to freedom. Take The Lead.
Voltage: 12V/24V DCPower Capacity: 720W @ 12V DC, 1920W @ 24V DCMaximum Current: 60 amp (Combined Total)Standby Power: <3mAPower Source: 3.7V Dc Lithium 1000 mAhFrequency: 433MhzCharge Time: 2-3 hrsCertification: CE, EMC, RoHSDimensions: 127 x 69 x 14mm (Controller), 192 x 135 x 36mm (Control Box)Weight: 160grams (Controller), 570grams (Control Box)Package Weight: 2.18 kg
Rhino-Rack
RHINO-RACK Vortex Complete Roof Rack Bundle For Byd Shark 6 - RX100-VA137B-LORD
$499.00
Conquer any adventure with the Rhino-Rack Vortex Complete Roof Rack Bundle for BYD Shark 6 - your professional solution for superior cargo carrying, aerodynamic performance, and reliability. Designed for adventurers, tradies, and weekend warriors, this proven system delivers strength, style, and security perfectly matched to your BYD Shark 6.
WHAT'S INCLUDED?
2X Rhino-Rack Vortex Bars (Black 1375mm) - aerodynamic design with VGS rubber strip
RX100 Leg System (x4) - 'Overland Tough' construction for BYD Shark 6 raised rails
VGS Rubber Strip - reduces wind drag and noise
Security Hardware - theft protection included
End Caps - complete professional finish
KEY BENEFITS
Aerodynamic Vortex design minimizes wind noise
'Overland Tough' construction for maximum durability
VGS rubber strip provides roof protection and noise reduction
Complete security hardware protects against theft
Seamless vehicle integration with sleek appearance
INSTALLATION OPTIONS
Choose DIY installation with Rhino-Rack's comprehensive step-by-step guide, or let our experienced team at TJM Northern Beaches handle the professional installation for you. With 15+ years of 4X4 expertise, we ensure perfect fitment and optimal performance for your specific vehicle.
Ready to upgrade your BYD Shark 6's roof carrying capacity? Contact TJM Northern Beaches today.
Rhino-Rack RX100
The Rhino-Rack RX100 roof rack system is designed specifically for use with roofs that feature raised rails. Built 'Overland Tough' with rugged good looks and vigorously tested to meet the needs of any adventurer, tradie or weekend warrior.
The system suits a wide range of activities and comes with security hardware to protect your racks against theft. The RX leg provides a seamless transition between product and vehicle, for a sleek look that doesn't compromise functionality. The system comes with a comprehensive step-by-step installation guide, for adventurers who choose to self-install.
100% load capacity in all conditions
System rated to 100kg/220lbs* or vehicle manufacturer’s roof load limit. Know your limits, visit www.rhinorack.com/loadrating.
Quick and easy installation and compatible with Rhino-Rack Vortex™ Bars and Pioneer™ Platforms
City Crash and durability tested by independent labs making it suitable for off-road use
Easy access to Vortex™ Bar channel for quick accessory installation
KEY BENEFITS
Package length: 500 mm
Package width: 140 mm
Package height: 90 mm
Warranty: 5 Years
Country of Origin: Australia
Rhino-Rack Vortex Bars
The Rhino-Rack Vortex bars can be purchased in black or silver and are cut to 7 different predefined lengths to suit different vehicles. All bars include the VGS rubber strip which has been designed to reduce wind drag and noise as well as providing added protection for your roof racks and load. All bars include end caps.
Vortex Bars available to replace your current bars (sold individually)
Bars come in black and silver colour options
Bars are cut to predefined lengths and are priced accordingly
All Vortex bars come with end caps
All Vortex Bars come with the VGS strip
KEY BENEFITS
Package length: 1440 mm
Package width: 90 mm
Package height: 50 mm
Warranty: 5 Years
Country of Origin: Australia
TJM
TJM Compressor Bundle - TJMCOMPRESSORBUNDLE
$799.00
Master every terrain with the TJM Compressor Bundle — your complete, high-performance solution for fast tyre inflation, pressure management, and air tool operation. Designed for serious 4WDers, this rugged setup delivers power, precision, and convenience — all for just $799. Limited-time offer.
What’s in the box?:
TJM Pro Series Twin Air Compressor – $789
TJM Tyre Inflation Kit – $99
TJM Pro Series Airline Kit – $85
TJM PRO SERIES TWIN AIR COMPRESSOR
SKU: 013COMPVPROTAARetail Price: $789.00
Built for high-demand performance, the TJM Pro Series Twin Air Compressor delivers an industry-leading 170LPM flow rate. Its dual motor design, convection cooling (patent pending), and hard-anodised internals ensure powerful inflation under pressure. Encased in a robust anodised aluminum body, it’s made to last.
Key Benefits:
170LPM fast inflation power
Dual motor with independent fail-safe operation
Vertical or horizontal mounting flexibility
Integrated 0.48L air tank and multiple ports for lockers or tools
Durable anodised alloy construction
3-year warranty
Specifications
Flow Rate: 170LPM
Tyre Inflation Time: 10–40 PSI for 285/75/R16
Ports:
4 × 1/8” BSPT (Pro Locker, pressure switch)
5 × ¼” BSPT (hose connector)
1 × 1/8” NPT (relief valve)
Air Tank: 0.48L with integrated extrusion
Bore Size: 48mm
Cooling System: Internal fan with convection cooling
Fuse Rating: 2 × 40A (ANS type)
Power Supply: 12V
Mounting: Vertical or horizontal
Weight: 14.60 kg
TJM TYRE INFLATION KIT
SKU: 013COMPDTIAARetail Price: $99.00
Engineered for ease and precision, the TJM Tyre Inflation Kit features a backlit digital display, 600mm rubber-reinforced hose, and robust brass fittings. A bleed valve and broad inflator button give you full control for accurate tyre management in any conditions.
Key Benefits:
Digital and analogue gauge options
Multiple units: PSI, KPA, Bar, Kgf/cm
Built-in bleed valve for easy deflation
Heavy-duty brass fittings with latch-type chuck
Wide compatibility with Nitto and US fittings
Specifications
Gauge Type: Digital and analogue
Digital Display Diameter: 60mm
Display Colour: Orange
Measuring Range: 5–200 PSI
Pressure Capacity: 200 PSI
Units: PSI, KPA, Kgf/cm², Bar
Fittings:
Brass tyre chuck (latch type)
Nitto & US-style air fittings
Hose: 600mm reinforced rubber
Weight: 1.16 kg
TJM PRO SERIES AIRLINE KIT
SKU: 013COMPAKNAARetail Price: $85.00
From tyre inflation to powering pneumatic tools, the TJM Airline Kit is your all-in-one air solution. It includes a 6m reinforced hose with quick-connect fittings, multiple inflation needles, an air blow gun, and a durable PVC storage case for organized use on the go.
Key Benefits:
6m rubber-reinforced hose with male/female Nitto fittings
Multiple inflation accessories for tyres, toys, and tools
Air blow gun with fittings for dust/off-road cleaning
Convenient storage bag for portability
Specifications
Hose Length: 6m
Hose Type: Rubber-reinforced with male/female Nitto fittings
Included Accessories:
Air blow gun with male Nitto fitting
Female Nitto one-touch fitting (1/4” BSPT thread)
Tyre inflation chuck
3 inflation needles (large, small, rubber tip)
Short air blow gun tip
PVC storage bag
Weight: 1.82 kg
Lightforce
LIGHTFORCE Beast 230Mm Clear Spot Filter- F230BEASTSC
$41.40
$46.00
LIGHTFORCE BEAST 230MM CLEAR SPOT FILTER- F230BEASTSC
Lightforce’s unique Modular Filter System has been applied to the new Beast LED Driving Light. The Clear Spot Filter adds even more protection over the moulded Beast lens and the bezel from road debris and impacts, without affecting the driving light's beam pattern.
Specifications
Colour: Clear
Beam Pattern: Spot
Size: 230mm
Material: Polycarbonate
