Load Bed and Roof Rack Kits

Introducing the VSS System for the Toyota Landcruiser 60 + 200 Series, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3 year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 18V Open Circuit Voltage (Voc) 21.24V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Nissan Patrol (2020 – Present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  65W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 65W Maximum Power Voltage (Vmp) 19V Open Circuit Voltage (Voc) 23V Maximum Power Current (Imp) 3.25A Short Circuit Current (Isc) 3.57A

Introducing the VSS System for the Ford F-150 Raptor (2018 – Present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  70W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 70W Maximum Power Voltage (Vmp) 17V Open Circuit Voltage (Voc) 20V Maximum Power Current (Imp) 4.11A Short Circuit Current (Isc) 4.52A

Introducing the VSS System for the Ford F-150 (2015 – 2020), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 17V Open Circuit Voltage (Voc) 20V Maximum Power Current (Imp) 5.3A Short Circuit Current (Isc) 5.8A

Introducing the VSS System for the Toyota FJ Cruiser - 105W, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  105W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - Moderate Benefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 105W Maximum Power Voltage (Vmp) 18V Open Circuit Voltage (Voc) 21.24V Maximum Power Current (Imp) 5.8A Short Circuit Current (Isc) 6.4A

Introducing the VSS System for the Toyota Landcruiser Prado, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

Introducing the VSS System for the Dodge RAM 1500 Limited (2019-Present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  70W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional PWM Solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 70W Maximum Power Voltage (Vmp) 17V Open Circuit Voltage (Voc) 20V Maximum Power Current (Imp) 4.11A Short Circuit Current (Isc) 4.52A  

**Special Order** Please contact us for ETA Introducing the VSS System for the Chevy Chevrolet Silverado Trail Boss (2019-2022), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  60W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3 year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits – Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 55W Maximum Power Voltage (Vmp) 17.5V Open Circuit Voltage (Voc) 21V Maximum Power Current (Imp) 3.14A Short Circuit Current (Isc) 3.45A

Introducing the VSS System for the Subaru Outback (2009 - 2019), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 18V Open Circuit Voltage (Voc) 21.24V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Ford Super Duty F250, F350, F450, F550 (2011 – 2016), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  95W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 95W Maximum Power Voltage (Vmp) 18.5V Open Circuit Voltage (Voc) 22V Maximum Power Current (Imp) 5.13A Short Circuit Current (Isc) 5.64A

Introducing the VSS System for the Toyota Landcruiser LC200, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W (2x45W) Maximum Power Voltage (Vmp) 17.5V Open Circuit Voltage (Voc) 21V Maximum Power Current (Imp) 5.14A Short Circuit Current (Isc) 5.64A

Introducing the VSS System for the Nissan Pathfinder (2004 - 2015), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

Introducing the VSS System for the Toyota Landcruiser 80 Series, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 18V Open Circuit Voltage (Voc) 21.24V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Chevy Silverado (2001 - 2011), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your vehicles battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits – Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24.78V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

Introducing the VSS System for the Toyota Hilux (2015 – 2025), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 20V Open Circuit Voltage (Voc) 20V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Toyota Landcruiser Prado (with scooped bonnet), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your Land Cruiser Prado battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional PWM Solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 17.5V Open Circuit Voltage (Voc) 21V Maximum Power Current (Imp) 5.14A Short Circuit Current (Isc) 5.64A

Introducing the VSS System for the Y62 Nissan Patrol (2010 – Current), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  98W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 98W Maximum Power Voltage (Vmp) 27.84V Open Circuit Voltage (Voc) 32.85V Maximum Power Current (Imp) 3.52A Short Circuit Current (Isc) 3.87A

Introducing the VSS System for the Ford Super Duty F350 (2005 – 2007), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  140w (2 x 70W) of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 140W Maximum Power Voltage (Vmp) 42V Open Circuit Voltage (Voc) 46V Maximum Power Current (Imp) 6.66A Short Circuit Current (Isc) 7.34A

Introducing the VSS System for the Toyota 4 Runner (2003 – 2021), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24.78V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

Introducing the VSS System for the Mitsubishi Triton L200 (2019-2024), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 18V Open Circuit Voltage (Voc) 21.24V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Suzuki Jimny (2018 – Present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  85W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 85W Maximum Power Voltage (Vmp) 24.36V Open Circuit Voltage (Voc) 28.74V Maximum Power Current (Imp) 3.48A Short Circuit Current (Isc) 3.83A

Introducing the VSS System for the Toyota Landcruiser 70 Series - 65-Watt (VDJ78 & VDJ79) 35W + 30W, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  65W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 65W Maximum Power Voltage (Vmp) 16V Open Circuit Voltage (Voc) 18.88V Maximum Power Current (Amp) 4.06A Short Circuit Current (Amp) 4.46A

Introducing the 115-Watt VSS System for the Toyota Landcruiser 100 Series, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  115W of clean solar energy to keep your Land Cruiser battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 115W Maximum Power Voltage (Vmp) 23V Open Circuit Voltage (Voc) 27.14V Maximum Power Current (Imp) 5A Short Circuit Current (Isc) 5.5A

Introducing the VSS System for the Holden Colorado (2015-2021), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  55W of clean solar energy to keep your cars battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 55W Maximum Power Voltage (Vmp) 17.5V Open Circuit Voltage (Voc) 21V Maximum Power Current (Imp) 3.14A Short Circuit Current (Isc) 3.45A

Introducing the VSS System for the Lexus LX450, LX470, LX570, GX460, GX470, GX570, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your Lexus battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24.78V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

A 6 (six) step ladder that provides easy access to your Front Runner Slimpro Van rack. Secures to the side profile of the Slimpro Van Rack and to the bottom trim of the vehicle. Made from high-strength steel, aluminum and powder coated in the same durable black powder coating as all Front Runner racks. Drilling is required on the bottom trim of the vehicle. All mounting hardware and fitment guide is included. Load Capacity 110 kg / 242.5 lbs. Features Consists of: 1 x Mercedes Sprinter H1 Slimpro Van Rack Ladder Installation Hardware Fitting instructions Materials used: Black powder coated aluminum and steel Product Dimensions: 343mm (13.5") L x 235mm (9.3") W x 2066mm (81.3") H Weight: 7.6 kg (16.8 lbs)

A 7 (seven) step ladder that provides easy access to your Front Runner Slimpro Van rack. Secures to the side profile of the Slimpro Van Rack and to the bottom trim of the Mercedes Sprinter H2. Made from high-strength steel, aluminum and powder coated in the same durable black powder coating as all Front Runner racks. Drilling is required on the bottom trim of the vehicle. All mounting hardware and fitment guide is included. Load Capacity 110 kg / 242.5 lbs. Features Consists of: 1 x Mercedes Sprinter H2 Ladder Installation Hardware Fitting Instructions Materials used: Black powder coated aluminium and steel Product Dimensions: 455mm (17.9") L x 235mm (9.3") W x 2348mm (92.4") H Weight: 7.9kg (17.4lbs)

This 2166mm/85.3" long, full-size, Slimline II cargo carrying roof rack kit for the Mitsubishi Delica Space Gear L400 contains the Slimline II Tray and Wind Fairing, as well as 8 Gutter Mount Legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. Installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRMD003T - Mitsubishi Delica Space Gear L400 (1994-2007) Slimline II Roof Rack Kit - by Front Runner Consisting of: 1x LASP104 - No 4 Plus Leg 180mm (Pair)1x LASS027 - Leg Spacer 6mm (Pair)2x LASS105 - No 5 Leg 190mm (Pair)1x LASS106 - No 6 Leg 195mm (Pair)1x RRAC174 - Wind Fairing for Low Profile Rack/1165MM/1255mm(W)1x RRSTG11 - SLII Tray - 1345mm(W)X2166mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 43.11kg (95.04lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18"); Length: 1720mm (68"); Height: 220mm (9")   Shipping Weight: Weight: 42.8kg (94lbs)

This kit consists of two (4) x Tent Brackets Works with both Front Runner Roof Racks and Front Runner Load Bars and fits a wide variety of hard shell tents including various ranges from James Baroud and Autohome. These brackets let you mount your James Baroud or Autohome tents with the proper lateral support, even if your rack is narrower or wider than your tent base. When fitting a James Baroud or Autohome tent to a rack that is smaller (narrower, shorter or both) than your tent base footprint, the included spacer raises the mounting height of the tent so it rests on the edge of the racks side profiles for full support. When mounted to a rack that is larger (longer and wider) than your tent base footprint, the brackets position your tent flush on the rack for full support and use of the included spacer isnt required. Supplied with all installation hardware and fitting instructions. Features Consists of: 4 x Tent Brackets 4 x James Baroud Channel Plates 4 x Auto Home Channel Plates Installation Hardware Fitting Instructions Materials used: Black powder coated steel Product Dimensions: (Per Bracket) 140mm (5.5") L x 23.5mm (0.9") W x 81mm (3.2") H Weight: (Per Pair of Brackets) 1.6kg (3.5lbs)

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1560mm/61.4'' (L). Features The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1156mm/45.5'' (L). Features The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This 2772mm/109.1" long, full-size, Slimline II cargo carrying roof rack kit for the Volkswagen T5/T6 Transporter LWB contains a Slimline II Tray, Wind Deflector, and 8 Feet. Installs easily into the existing factory/OEM roof tracks with no drilling required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: This Kit required the OEM tracks for installation. Features KRVT015T - Volkswagen T5/T6 Transporter LWB w/OEM Tracks (2003-Current) Slimline II Roof Rack Kit - by Front Runner Consisting of: 4x FASS017 - Foot Set / 75mm-85mm1x RRSTJ14 - SLII Tray - 1425mm(W)X2772mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 41.84kg (92.24lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 230mm (9")   Shipping Weight: Weight: 47.6kg (105lbs)

This Rack Kit is for truck canopies/camper shells/caps and trailers that have roof top sizes no larger than approximately 1345mm/53" (W) x 1560mm/61.4" (L). The Slimline II Tray mounts to six (6) supplied Feet that slide in to the supplied Track. The 1500mm/59” long pair of tracks can be easily mounted to your canopy/shell or trailer.See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:3x FASS024 - Foot Set / 50mm - 60mm1x RRSTG08 - SLII Tray - 1345mm(W)X1560mm(L)1x TRCA004 - Canopy Tracks / 1500mm(L)Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 29.46kg (64.95lbs)The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts.To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions:Width: 440mm (17")Length: 1730mm (68")Height: 270mm (11")Shipping Weight:Weight: 34.4kg (76lbs)

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2368mm/93.2'' (L). Features The Slimline II Tray mounts to eight (8) supplied Feet that slide into the supplied Track. The 2 x 750mm/29.5 long pair of tracks can be easily mounted to your canopy/shell or trailer. Installation See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1358mm/53.5'' (L). Features The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2570mm/101.2'' (L). Features The Slimline II Tray mounts to eight (8) supplied Feet that slide into the supplied Track. The 2 x 1150mm/45.3 long pair of tracks can be easily mounted to your canopy/shell or trailer. Installation See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2772mm/109.1'' (L). Features The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2166mm/85.3'' (L). Features The Slimline II Tray mounts to eight (8) supplied Feet that slide into the supplied Track. The 2 x 750mm/29.5 long pair of tracks can be easily mounted to your canopy/shell or trailer. Installation See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1762mm/69.4'' (L). Features The Slimline II Tray and six (6) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1964mm/77.3'' (L). Features The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2166mm/85.3'' (L). Features The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 1762mm/69.4'' (L). Features The Slimline II Tray mounts to eight (8) supplied Feet that slide into the supplied Track. The 1600mm/63” long pair of tracks can be easily mounted to your canopy/shell or trailer. Installation See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2368mm/93.2'' (L). Features The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1425mm/56.1'' (W) x 1358mm/53.5'' (L). Features The Slimline II Tray mounts to six (6) supplied Feet that slide into the supplied Track. The 3 x 140mm/5.5” long pair of tracks can be easily mounted to your canopy/shell or trailer. See the Track installation instructions in the INSTALL tab for further details. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1425mm/56.1'' (W) x 954mm/37.6'' (L). Features The Slimline II Tray mounts to four (4) supplied Feet that slide into the supplied Track. The 1150mm/45.3” long pair of tracks can be easily mounted to your canopy/shell or trailer. See the Track installation instructions in the INSTALL tab for further details. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2772mm/109.1'' (L). Features The Slimline II Tray mounts to eight (8) supplied Feet that slide into the supplied Track. The 2 x 1150mm/45.3 long pair of tracks can be easily mounted to your canopy/shell or trailer. Installation See the Track installation instructions in the INSTALL tab for further details. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1425mm/56.1'' (W) x 1156mm/45.5'' (L). Features The Slimline II Tray mounts to four (4) supplied Feet that slide onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track.** Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1425mm/56.1'' (W) x 752mm/29.6'' (L). Features The Slimline II Tray and four (4) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1345mm/53'' (W) x 2570mm/101.2'' (L). Features The Slimline II Tray and eight (8) supplied Feet mount onto the OEM/Factory installed track of your canopy/shell or trailer. NOTE: Additional fasteners may be required to fit OEM/Factory supplied tracks. Track Requirements In order for Front Runner Feet and supplied hardware to work with your OEM/Factory supplied canopy track, the track must have: Slot base width min 20mm / max 25mm Slot base height min 6.5mm / max 10mm Slot opening width min 8.5mm / max 10.5mm Slot opening height min 2mm / max 5mm **Please check with the canopy manufacturer regarding the load ratings for your specific canopy and track. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.

This Rack Kit is designed for truck canopies/camper shells/caps and trailers that have rooftop sizes no larger than approximately 1425mm/56.1'' (W) x 752mm/29.6'' (L). Features The Slimline II Tray mounts to four (4) supplied Feet that slide into the supplied Track. The 750mm/29.5” long pair of tracks can be easily mounted to your canopy/shell or trailer. Track Installation See the Track installation instructions in the INSTALL tab for further details. Installation All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. Warranty All Front Runner Racks are backed by a Limited Lifetime Warranty*.