Land Rover Defender Touring Accessories and Roof Racks

A set of Gutter Mounted Load Bars used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 225mm Gutter Mount legs, 2 1425mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to a vehicle with gutters. You may not have the need for a full roof rack and find that you can get by using a set of Front Runner load bars. Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred. The Load Bars are mounted directly to the rain gutters using Gutter Mounted Legs. Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. The Load Bars and Gutter Mount Legs can be used in the future as components to build a complete Front Runner Roof Rack. Made from stainless steel and a durable, weather resistant black powder-coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLD024 - Land Rover Defender (1983-2016) Load Bar Kit / Gutter Mount - by Front Runner Consisting of: 2 x LASS107 - No 7 Leg 225mm (Pair) - by Front Runner 1 x LBSK016 - Roof Load Bar Pair 1425mm(W) - by Front Runner 1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 8kg (18lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 130mm (5") Length 1540mm (61") Height 195mm (8") Shipping Weight: Weight 9.5kg (21.0lbs)

This ladder clamps onto the gutter and bolts to the vehicle body. The bottom rung mounts below the bumper using existing holes. The ladder conforms to the contours of the vehicle and is made with off-road tough black powder-coated high-strength steel for maximum durability and strength. Easy installation: The top part of the ladder clamps onto the gutter and bolts to the vehicle body (drilling required). The bottom step mounts below the bumper using existing holes. Features Consists of: 1 x Land Rover Defender 90 110 (1983-2016) Ladder Installation Hardware Fitting Instructions Materials used: Black Powder coated steel & aluminium Product Dimensions: 155mm (6.1") L x 230mm (9.1") W x 721mm (28.4") H Weight: 4.51kg (9.9lbs)

A spare wheel carrier that mounts onto your Land Rover Defender 90 & 110 Station Wagon and keeps that spare wheel safe and secure.

Front Runner sump guards are designed for specific vehicle makes and models to ensure that the correct parts of the vehicle are protected from damage. Made of 6mm aluminium. Natural aluminum finish to compliment the Land Rover Defender. Fits both Left Hand and Right Hand drive vehicles. The 8mm black powder coated steel brackets mount to the existing mounting points on the Land Rover Defender. No drilling or vehicle modification required. Features Consists of: 1 x Aluminum Guard Plate 1 x Pair of Brackets Installation Hardware Fitting Instructions Materials used: 6mm Aluminum plate Black powder coated 8mm mild steel Product Dimensions: 373.5mm (14.7") L x 750mm (29.5") W x 252mm (9.9") H (Including brackets) Weight: 18.5kg (40.8lbs) Special Notes: Fits the Land Rover Defender 90 & 110 series

The Front Runner Gullwing window replaces the rear window of a Land Rover Defender allowing easy access to the cargo bay via the side of the vehicle.While built for off-road durability and ease of use, the Front Runner Aluminum Gullwing Window looks smart and was designed to blend seamlessly with the exterior stylings of the vehicle. Fits in minutes, no modifications required. Sealed with the same durable, weather resistant powder coating as the Front Runner Slimline II Roof Rack. Includes 2 locking latches. The Land Rover Defender can be brought back to stock within minutes by removing and replacing with standard window. Note: The glass and aluminium panels for the Land Rover Defender are not interchangeable.   Consists of:1x Aluminium gullwing door assembly1x Outer frame1x Fastening kit2x Gas struts1x Right side inner bracket1x Left side inner bracket1x Top inner bracket1x Bottom inner bracketMaterials used:Black powder-coated 3mm aluminiumBlack powder-coated 2mm mild steel reinforcement plateBlack powder-coated high strength steelProduct Dimensions:Overall: L 1120mm (44.1") x W 50mm (2") x H 490mm (19.3")Door Panel: L 1044mm (41.1") x H 414mm (16.3")Weight:15.5kg (34.2lbs)

This 752mm/29.6" long full-size Slimline II cargo carrying roof rack kit for the Land Rover Defender Single Cab Pickup contains Slimline II Tray and Wind Deflector, as well as 4 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle.All Front Runner Racks are backed by a Limited Lifetime Warranty*   KRLD009L - Land Rover Defender Single Cab (1983-2016) Pick-Up Truck Slimline II Roof Rack Kit Consisting of: 2 x LASS104 - No 4 Leg 170mm (Pair) - by Front Runner1 x RRSTJ04 - Slimline II Tray - 1425mm(W) X 752mm(L) - by Front RunnerMaterial used: Black epoxy powder-coated T6 aluminiumHigh strength steel Approximate Installed Weight 19kg (41lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicle’s roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above.If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicle’s rain gutters.If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof.Shipping Dimensions: Width 450mm (18")Length 1615mm (64")Height 140mm (6") Shipping Weight: Weight 21.9kg (48.2lbs)

A shelf that fits into the Front Runner Gullwing Box for the Land Rover Defender TDI/TD5.Use these shelves to create different sections in the Gullwing Box for storing goods, crockery and supplies.Consists of: 1x Wooden shelf1x Mild steel frame1x Fastening KitMaterial used: Shelf: Stained PlywoodFrame: Black powder-coated mild steelProduct dimensions: L 209mm (8.2") x W 997mm (39.3") x h 36mm (1.4")Weight:3.8kg (8.4lbs)

Keep your vehicle's headlights protected from damage with these tough, plastic coated, headlight protectors. Made out of high strength steel. Polyethylene plastic coated for protection against the elements. Mounts to existing mounting points on your Land Rover Defender and uses the original nuts and bolts. Designed specifically for your Land Rover Defender.

A spare wheel carrier for the Land Rover Defender 130/DC Ute. Allows fitment of an additional spare wheel to the rear of the vehicle. Secures to the chassis and the load bed body with supplied brackets and hardware. The spare wheel can then swing open to allow the tail gate to be opened. Load capacity 60kg (132.3lbs)

The same trusted and off-rough tough Front Runner lockable Jerry Can Holder, only conveniently reconfigured to mount on the side of the vehicle via a gutter mount. The adjustable stainless steel latch with safety catch holds your Jerry Can firmly in place over a lifetime of off-road abuse. For use with 20l / 5.3 gallon NATO/Wedco style military cans. This strap covers the Jerry can cap. Add your own padlock or Rack Accessory Lock / Small and you'll never have to worry about stolen fuel while on the road. Simple installation that uses an existing pop-rivet hole. Made of durable black powder coated high strength steel and designed to mount to the rain gutter on vehicles like the classic Land Rovers. Note: Will not work with Scepter style cans.Note: This Jerry Can Holder is not compatible with the Land Rover New Defender. Consists of:1 x Side Mount Jerry Can HolderInstallation HardwareFitting Instruction Materials used:Black powder coated high strength steel Product Dimensions:230mm (9.1") L x 385mm (15.2") W x 711mm (28") H Weight:5.5kg (12.1lbs)

​​The Front Runner Gullwing Box is used in conjunction with the Front Runner Gullwing Window-Glass or Front Runner Gullwing Window-Aluminium and creates a convinient storage compartment accessible through the side of your vehicle. The Front Runner Gullwing Box is used in conjunction with the Front Runner Gullwing Window-Glass or Front Runner Gullwing Window-Aluminium. This creates extra convenient storage space for your Land Rover Defender TDI/TD5. Front Runner Gullwing Box Shelves can be used to create divisions in the box for storage. *Front Runner Gullwing Box Shelves, sold seperately. Consists of:1x Fastening Kit2x Pinch Welds2x Side Panels - 1 Left, 1 Right2x Mounting Brackets1x Top Panel2x Wooden Back Panels1x Bottom PanelMaterials used:Black powder-coated mild steelProduct Dimensions:L 255mm (10") x W 1000mm (39.4") x H 654mm (25.8")Weight:13.1kg (28.9lbs)

The Front Runner Gullwing Box is used in conjunction with the Front Runner Gullwing Window-Glass or Front Runner Gullwing Window-Aluminium. This creates extra convenient storage space for your Land Rover Defender Puma. Front Runner Gullwing Box Shelves can be used to create divisions in the box for storage. *Front Runner Gullwing Box Shelves, sold seperately. Consists of:1x Fastening Kit2x Pinch Welds2x Side Panels - 1 Left, 1 Right2x Mounting Brackets1x Top Panel2x Wooden Back Board1x Bottom PanelMaterials used:Black powder coated steelBack Board: Stained PlywoodProduct dimensions:860mm (33.9") W x 310mm (12.2") L x 654mm (25.8") H (Box)860mm (33.9") W x 310mm (12.2") L x 746mm (29.4") H (Overall incl. Brackets)Weight:13.1kg (28.9lbs)

The Front Runner Glass Gullwing Window replaces the rear window of a Defender and allows you to tilt​ up the window, creating 100% easy access to the contents of your load area.     The locking Front Runner Gullwing Window can be fitted together with the Front Runner Gullwing Box (GWDL004) to create extra gear storage possibilities.  The 6mm toughened glass with tinted laminate​ allows you to see what is stored, keeps your valuables secure, and adds a stylish finish to your vehicle's exterior.​​Note: The glass and aluminium panels for the Land Rover Defender are not interchangeable. Consists of:1x Glass gullwing door assembly1x Outer frame1x Fastening kit2x Gas struts1x Right side inner bracket1x Left side inner bracket1x Top inner bracket1x Bottom inner bracketMaterials used:6mm Toughened glass with tinted laminateBlack powder-coated high strength steelProduct Dimensions:Overall: L 1120mm (44.1") x W 50mm (2") x H 490mm (19.3")Door Panel: L 1044mm (41.1") x H 414mm (16.3")Weight:15kg (33.1lbs)Glass specifications:Visible Light:Transmission: 44Reflection Outside: 5Solar Energy:Total Elimination: 38Reflection Outside: 5Absorption 1: 47Direct Transmission: 47SHGC: 0.62Shading Coefficient:Ratio: 0.71U Value:(W/m2).K (Center of Glass): 5.8

A 1.6mm thick aluminium tread plate that fits on top of the fender of your vehicle for added protection. Made from black powder coated aluminium. Protects the fender against dents and scratching. Suitable for all Defender models. BPLD017 - Land Rover Defender 90/110 (1983-2016) Fender Protector / Black - by Front RunnerMaterial Used:Black epoxy powder - coated T6 aluminiumApproximate Installed Weight: 2.2kg (4.85lbs)Shipping Dimensions:Width: 380mm (15")Length: 1130mm (44")Height: 35mm (1")Shipping Weight:Weight: 2.2kg (5lbs)

The Polyair Red Series load assist airbag kits are specifically designed to suit coil sprung vehicles. When you load up the back of the vehicle or hook up a caravan or trailer, you’ll notice the rear end drop down; this drop can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - suspension bottoming out - rough ride - excessive sway & body roll - unpredictable braking characteristics - poor headlight aim All this can be mitigated by simply installing a set of Polyair Red Series! The airbag kit is air adjustable, giving you flexibility to tailor the level of support for your individual load types and weights. Having a correctly sprung vehicle for constant loads is always recommended as the first step, but in most cases the coil springs are rated well past what you will carry on a daily basis, giving you a rough, uncomfortable ride when not loaded up. Having the flexibility of the adjustable Polyair Red Series means you can have a smooth OEM ride comfort when unloaded and simply adjust the pressure when towing or hauling. Simple. Features: - Air adjustable from 5-35psi - Tough moulded polyurethane construction - Easy to install using common tools - Easy to follow, illustrated instructions - Quick connecting, easy to use air fittings. 2 year, unlimited km warranty Position: Rear Landrover - Defender 110 1983 - 2016

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.Product Code: WT-RD130-2213UFitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.Product Code: WT-RD110F-2212UFitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.Product Code: WT-RD110-2013UFitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.For over four decades, the entirely fabricated and welded 'Commercial-Max' roof racks have set the standard of strength in Australia, offering individually designed mounting systems and custom platform dimensions tailored to specific vehicle makes and models.Engineered forTradespeople, especially those carrying bulky and heavier materialsAvailable For Most vans, new and old Older 4WD vehicles Ute canopies Vehicle Fitment: LAND ROVER DEFENDER 90 GEN 1Product Code: RD90Fitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.The Oval Steel roof rack is manufactured using oval steel tubing for superior strength and reduced wind resistance. Completely made in Australia, it's built for Australian conditions and customised for individual vehicle makes and models. Our uniquely designed mounting systems provide the strength required to carry heavy loads and withstand the demands of outback touring.A superior finish and strength are guaranteed through our advanced welding process. Additionally, the racks are zinc-plated to increase corrosion resistance. They're lighter than most steel racks and stronger than alloy alternatives, making them an excellent choice for tough conditions.The Oval Steel range offers various styles, including baskets with four sides, open ends with two sides, flat decks with no sides, tents with three sides at the front and no sides at the rear, and canopies. No matter your needs, we have the perfect option for you.Vehicle Fitment: LAND ROVER DEFENDER 90 GEN 1Product Code: OVRD90Fitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.The Oval Steel roof rack is manufactured using oval steel tubing for superior strength and reduced wind resistance. Completely made in Australia, it's built for Australian conditions and customised for individual vehicle makes and models. Our uniquely designed mounting systems provide the strength required to carry heavy loads and withstand the demands of outback touring.A superior finish and strength are guaranteed through our advanced welding process. Additionally, the racks are zinc-plated to increase corrosion resistance. They're lighter than most steel racks and stronger than alloy alternatives, making them an excellent choice for tough conditions.The Oval Steel range offers various styles, including baskets with four sides, open ends with two sides, flat decks with no sides, tents with three sides at the front and no sides at the rear, and canopies. No matter your needs, we have the perfect option for you.Vehicle Fitment: LAND ROVER DEFENDER 110 GEN 1Product Code: OVRD110Fitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.The Oval Steel roof rack is manufactured using oval steel tubing for superior strength and reduced wind resistance. Completely made in Australia, it's built for Australian conditions and customised for individual vehicle makes and models. Our uniquely designed mounting systems provide the strength required to carry heavy loads and withstand the demands of outback touring.A superior finish and strength are guaranteed through our advanced welding process. Additionally, the racks are zinc-plated to increase corrosion resistance. They're lighter than most steel racks and stronger than alloy alternatives, making them an excellent choice for tough conditions.The Oval Steel range offers various styles, including baskets with four sides, open ends with two sides, flat decks with no sides, tents with three sides at the front and no sides at the rear, and canopies. No matter your needs, we have the perfect option for you.Vehicle Fitment: LAND ROVER DEFENDER 130 GEN 1Product Code: OVRD130Fitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.For over four decades, the entirely fabricated and welded 'Commercial-Max' roof racks have set the standard of strength in Australia, offering individually designed mounting systems and custom platform dimensions tailored to specific vehicle makes and models.Engineered forTradespeople, especially those carrying bulky and heavier materialsAvailable For Most vans, new and old Older 4WD vehicles Ute canopies Vehicle Fitment: LAND ROVER DEFENDER 130 GEN 1Product Code: RD130Fitting Instructions

Wedgetail is the culmination of forty-six years of Australian roof rack manufacturing experience. This experience has brought you a world-class product.For over four decades, the entirely fabricated and welded 'Commercial-Max' roof racks have set the standard of strength in Australia, offering individually designed mounting systems and custom platform dimensions tailored to specific vehicle makes and models.Engineered forTradespeople, especially those carrying bulky and heavier materialsAvailable For Most vans, new and old Older 4WD vehicles Ute canopies Vehicle Fitment: LAND ROVER DEFENDER 110 GEN 1Product Code: RD110Fitting Instructions

Introducing the VSS System for the Land Rover Defender (2020-present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  90W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 90W Maximum Power Voltage (Vmp) 17.5V Open Circuit Voltage (Voc) 21V Maximum Power Current (Imp) 5.14A Short Circuit Current (Isc) 5.65

OUT OF STOCK – Pre-Order Now Introducing the VSS System for the Land Rover Defender (2007-2015), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  50W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 50W Maximum Power Voltage (Vmp) 20V Open Circuit Voltage (Voc) 23.6V Maximum Power Current (Imp) 2.5A Short Circuit Current (Isc) 2.75

Introducing the VSS System for Land Rover Defender (1984 - 2006), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  75W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 75W) Maximum Power Voltage (Vmp) 20V Open Circuit Voltage (Voc) 24V Maximum Power Current (Imp) 4.16A Short Circuit Current (Isc) 4.58A

Front Runner Hi-Lift Jack Rear Bumper Mount for Land Rover Defender Carry your Hi-Lift Jack securely without the need for a roof rack using the Front Runner Hi-Lift Jack Rear Bumper Mount. Specifically designed for the Land Rover Defender, this rugged mounting solution allows you to store your jack conveniently on the rear bumper for quick access when recovery situations arise. Constructed from black powder-coated high-strength steel, this durable two-piece bracket is engineered to withstand harsh weather conditions, rough tracks, and demanding off-road use. The rear bumper mounting position provides easy access to your Hi-Lift Jack without the need to climb onto your vehicle, making recovery equipment more accessible when you need it most. In addition to its practical functionality, this bumper mount adds a distinctive off-road appearance to your Defender, enhancing both style and capability. Key Features Designed specifically for Land Rover Defender vehicles. Securely mounts a 1.2m Hi-Lift Jack to the rear bumper. Heavy-duty two-piece mounting bracket design. Manufactured from high-strength steel. Black powder-coated finish for corrosion resistance. Lockable design for added security. Provides quick and easy access to your recovery jack. Enhances the rugged appearance of your Defender. Benefits Eliminates the need for roof rack-mounted jack storage. Keeps recovery equipment easily accessible. Protects your jack during off-road travel. Offers a secure and convenient mounting solution. Adds a functional off-road aesthetic to your vehicle. Compatibility Suitable for Land Rover Defender models. Designed to carry one 1.2m Hi-Lift Jack. Compatible with user-supplied padlocks for added security. Construction Material: High-strength steel. Finish: Black powder-coated. Built for long-term durability and outdoor use. Important Information Hi-Lift Jack sold separately. Padlock not included. Professional installation is recommended if you are unfamiliar with vehicle accessory fitting.

Front Runner Land Rover Defender 110 Sill Protector Black - BPLD003 Protect your vehicle's door sills from everyday wear and off-road damage with the Front Runner Sill Protector for the Land Rover Defender 110. Designed specifically for Defender 110 models, these durable aluminium tread plates provide an extra layer of protection against scratches, dents, scuffs, and impacts. Manufactured from 1.6mm thick aluminium and finished in a tough black powder coating, the sill protectors are built to withstand harsh conditions while complementing the rugged appearance of your Defender. Whether you're frequently entering and exiting the vehicle, loading equipment, or tackling challenging terrain, these protectors help preserve your vehicle's bodywork and maintain its appearance. Key Features Designed specifically for Land Rover Defender 110 models (1983–2016). Provides added protection for vehicle door sills and corners. Manufactured from durable 1.6mm thick aluminium tread plate. Black powder-coated finish for enhanced durability and corrosion resistance. Helps prevent dents, scratches, scuffs, and impact damage. Enhances the rugged appearance of the vehicle. Built to withstand demanding off-road and touring conditions. Benefits Protects vulnerable sill areas from everyday wear and tear. Reduces the risk of costly bodywork repairs. Maintains the appearance and value of your vehicle. Provides long-lasting protection in harsh environments. Complements the Defender's rugged styling. Construction Material: 1.6mm thick aluminium tread plate. Finish: Black powder-coated. Corrosion-resistant and weather-resistant construction. Compatibility Suitable for Land Rover Defender 110 models (1983–2016). Engineered for a precise vehicle-specific fit. Important Information Designed specifically for Defender 110 models. Please verify vehicle compatibility before purchase. Professional installation is recommended if required.

This 1358mm/53.5" long 1/2 size Slimline II cargo carrying roof rack kit for the Land Rover Defender contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner Camp Tables or other compatible accessories under the rack. Installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLDT01L - Land Rover Defender (1983-2016) Slimline II 1/2 Roof Rack Kit / Tall - by Front Runner Consisting of: 3x LASS108 - No 8 Leg 250mm (Pair) 1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 31.48kg (69.4lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18") Length: 1730mm (68") Height: 140mm (6") Shipping Weight: Weight: 31.48kg (69lbs)

This safe is bolted to the body of the vehicle under the original center console and is manufactured from 2mm thick mild steel. It features a tamper proof cam lock and is carpet lined to protect your valuables and prevent rattling. Please Note: Installation of this product requires a Rivnut tool. We suggest using the Rivnut tool / M6/M8. Features Consists of: 1x Under console safe 2x Keys supplied Materials used: Black powder-coated mild steel Carpeted base Product Dimensions: 433mm (17.1") L x 275mm (10.8") W x H 100mm (3.9") Internal Dimensions: 375mm (14.8") L x 265mm W (10.4") (Raised section)/205mm (8.1") W (Lower Section) x 107mm (4.2") H Weight: 3.2kg (7.1lbs)

This 2166mm/85.3" long, 3/4 size, Slimline II cargo carrying roof rack kit for your Land Rover Defender 110 contains the Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount Legs for mounting the Tray to the vehicle. Installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRLD035T - Land Rover Defender 110 (1983-2016) Slimline II 3/4 Roof Rack Kit - by Front Runner Consisting of: 4x LASS107 - No 7 Leg 225mm (Pair) 1x RRSTJ11 - SLII Tray - 1425mm(W)X2166mm(L) 1x WDST009 - Wind Deflector 20mm Lip Wide Pair / 1345mm(W) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 42.74kg (94.23lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1720mm (68") Height: 280mm (11") Shipping Weight: Weight: 43.4kg (95lbs)

This 2166mm/85.3" 3/4 size Slimline II cargo carrying roof rack kit for your Land Rover Defender 110 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. This kit has space for mounting the Front Runner tables or other compatible accessories under the rack. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRLD030L - Land Rover Defender 110 (1983-2016) Slimline II 3/4 Roof Rack Kit / Tall - by Front Runner Consisting of: 4x LASS108 - No 8 Leg 250mm (Pair)1x RRSTJ11 - SLII Tray - 1425mm(W)X2166mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 34.1kg (75.18lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18"); Length: 1730mm (68"); Height: 140mm (6")   Shipping Weight: Weight: 40.48kg (89lbs)

This 2772mm/109" long full-size Slimline II cargo carrying roof rack kit for the Land Rover Defender 110 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLD003L - Land Rover Defender 110 (1983-2016) Slimline II Roof Rack Kit - by Front Runner Consisting of: 4 x LASS107 - No 7 Leg 225mm (Pair) - by Front Runner 1 x RRSTJ14 - Slimline II Tray - 1425mm(W) X 2772mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 42kg (92lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight 48.8kg (107.3lbs)

This 2772mm/109" long full-size Slimline II cargo carrying roof rack kit for the Land Rover Defender 110 contains Slimline II Tray and Wind Deflector, as well as 8 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. It installs easily with no drilling required.   All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLDT03L - Land Rover Defender 110 (1983-2016) Slimline II Roof Rack Kit / Tall - by Front Runner Consisting of: 4 x LASS108 - No 8 Leg 250mm (Pair) - by Front Runner 1 x RRSTJ14 - Slimline II Tray - 1425mm(W) X 2772mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 42kg (93lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight 49.0kg (107.8lbs)

This 1762mm/69.4 long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 4 Contour Rails to mount the Slimline II Tray to your Land Rover Defender 110 L663. Easily installs using the existing factory rails. No drilling is required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle-specific contour rails have openings for storing compatible gear under the rack such as Front Runner tables. An opening on the Contour Rails allows access to Front Runner under rack mount table (Pro Stainless Steel Prep Table Kit). All Front Runner Racks are backed by a Limited Lifetime Warranty* Features KRLD042T - Land Rover Defender 110 L663 (2020-Current) Slimline II Roof Rack Contour Kit Consisting of: 1x FALD012 - Land Rover Defender L663 (2020-Cur) Contour Rail 1x RRSTD09 - SLII Tray - 1255mm(W)X1762mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 32.41kg (71.45lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 450mm (18") Length: 1720mm (68") Height: 275mm (11") Shipping Weight: Weight: 32kg (70lbs)

This water tank comes with a mounting bracket and hose kit included Mounts underneath your Land Rover Defender 110 Capacity: 36l (9.5gal) Made from food grade polyethylene and BPA free Features Materials used: BPA-free polyethylene Dimensions (mm): Slanted from 560W to 380W x 270H x 310L

This water tank comes with a mounting bracket and hose kit included Mounts underneath your Land Rover Defender 110 Capacity: 36l (9.5gal) Made from food grade polyethylene and BPA free Features Materials used: BPA-free polyethylene Dimensions (mm): Slanted from 560W to 370W x 320H x 315L

This 1560mm/61.4" long 1/2 size Slimline II cargo carrying roof rack kit for the Land Rover Defender 110/130 contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the vehicle. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLD005L - Land Rover Defender 110/130 (1983-2016) Slimline II 1/2 Roof Rack Kit - by Front Runner Consisting of: 3 x LASS107 - No 7 Leg 225mm (Pair) - by Front Runner 1 x RRSTJ08 - Slimline II Tray - 1425mm(W) X 1560mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 31kg (68lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight 35.8kg (78.8lbs)

This 1560mm/61.4" long 1/2 size Slimline II cargo carrying roof rack kit for the Land Rover Defender 110/130 contains Slimline II Tray and Wind Deflector, as well as 6 Gutter Mount legs for mounting the Tray to the vehicle. This taller kit has space for mounting the Front Runner tables or other compatible accessories under the rack. It installs easily with no drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLDT05L - Land Rover Defender 110/130 (1983-2016) Slimline II 1/2 Roof Rack Kit / Tall - by Front Runner Consisting of: 3 x LASS108 - No 8 Leg 250mm (Pair) - by Front Runner 1 x RRSTJ08 - Slimline II Tray - 1425mm(W) X 1560mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 29kg (64lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/ 2") to the height of the Legs to determine the height of the rack from your vehicles rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/ 2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 450mm (18") Length 1615mm (64") Height 140mm (6") Shipping Weight: Weight: 33.8kg (74.3lbs)

This kit creates a full-size rack that sits above your Land Rover Defender 130's truck bed. This Slimline II rack kit contains the Slimline II tray (1575mm x 1358mm), two (2) tracks, and six (6) pickup truck bed universal legs that fit into the tracks. All Front Runner rack kits contain installation instructions as well as all the components needed to mount the Slimline II tray to your vehicle. All Front Runner racks are backed by a limited lifetime warranty* Drilling is required to mount the track to the bed of your truck. Features KRLD041T - Land Rover Defender 130 (1983-2016) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS030 - Universal Load Bed Leg / Medium (Pair) 1x RRSTP07 - SLII Tray - 1575mm(W)X1358mm(L) 1x TRBU003 - Pick-Up Load Bed Tracks / 1400mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 32.6kg (71.87lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1730mm (68") Height: 265mm (10") Shipping Weight: Weight: 34kg (75lbs)

Get your extremely capable Land Rover Defender 130 ready for heavy gear-carrying duties with the modular Slimline II Roof Rack Kit. With over 55 accessories available for this tough rack, you can confidently tackle any adventure with the right gear. This 2368mm/93.2" long full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Land Rover Defender 130. It easily installs using the existing factory mounting points. No drilling required. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 2 openings to access a Front Runner under rack mount table (1 smaller prep table and 1 larger camp size table). All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: The OEM Tracks need to be removed when fitting this Rack Kit. Vehicles with the panoramic sunroof, only the rear, large table can be fitted. If you fit the front table you will not be able to open the sunroof. Features KRLD043T - Land Rover Defender 130 Slimline II Roof Rack Kit Consisting of: 1x FALD013 - Land Rover Defender 130 (2022-Curr) Foot Rails 1x RRSTD12 - SLII Tray - 1255mm(W)X2368mm(L) Material Used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 41.87kg (92.31lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicle's roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1720mm (68") Height: 280mm (11") Shipping Weight: Weight: 45kg (99lbs)