Coilover Systems

Take your 21-23 F150 to new heights with this 6" lift kit from Zone Offroad. Kits include everything needed from high strength crossmembers and steering knuckles to strut spacers and rear block kit to level out the stance. Engineered to the highest standard to maintain ride quality and handling performance. Get the look, performance, and capability your truck deserves with clearance for 35-37" tires. Optimizes ground clearance and off-road protection Maintains drivability and handling performance Redesigned steering knuckles for ESC compliance Available rear lift blocks for desired stance Includes Factory Protection Plus for peace of mind Allows clearance for larger tires Specifications Front Lift Height: 6" Material: Steel Front Lift Method: Strut Spacers Lift Type: Suspension Features & Benefits Kit design optimizes ground clearance and improves offroad protection Maintains drivability and handling by correcting suspension, steering and driveline geometry. Redesigned steering knuckles specific to the 2021-2022 F150 to maintain ESC system compliance 4" or 5" replacement rear lift blocks available to achieve desired stance without the need to stack lift blocks Kits includes Factory Protection Plus (ESC system compatibility, Limited lifetime warranty, 5yr-60k mile drivetrain warranty) Kit allows clearance for 35" tires Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 5.75 in. Backspace 35 x 12.5 with 20 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 10 hours Difficulty: Hard Install Tools 204-592 Ball Joint Separator (Recommended) Tie Rod End Separator (Recommended) Torque Wrench Reciprocating Saw Socket Wrench Important Notes Will fit models with Auto 4wd that do NOT have the 4WD actuator hub assembly Some trucks with a 2 piece drive shaft may have a recall from Ford regarding the rear drive shaft. (Safety Recall 21S25) Due to the recall procedure, Zone Offroad recommends to have this performed prior to installing the lift.” 18" or larger diameter wheels required. Stock 17" and 18" wheels cannot be reinstalled. Stock 20’ wheels can be used with up to a 305/60R20 tire. 18" wheels with 5-5.5" backspacing should be test fit prior to mounting the tire to ensure proper clearance to the steering knuckle/tie rod. 18 - 20"wheels with 5.5-5.75" of backspacing is highly recommended for tire to frame crash bar clearance. 37" tires will require crash bar modification Models with 2-piece rear driveshaft WILL require carrier bearing shim kit D5405 (not included w/ kit). Block kits replace factory 1-1/4” block. Stock block will not be reinstalled. Crash bars may require modification based on wheel and tire choice. It is the end users responsibility to ensure modifications are non-detrimental to vehicle safety. Will not work with trucks equipped with CCD (Continuous Controlled Damping) Does not fit diesel models. Will not fit Tremor models. Requires frame bracket modification This system has not been tested on models equipped with Ford BlueCruise ComponentsKit Components ZONF2638: Zone Offroad 2021-2024 Ford F150 5" Rear Box Kit ZONF2660: Zone Offroad 2021-2024 Ford F150 Knuckle Box Kit - DS ZONF2661: Zone Offroad 2021-2023 Ford F150 Knuckle Box Kit - PS ZONF2662: Zone 2021-2023 Ford F150 Front Box Kit ZONF2663: Zone Offroad 2021-2023 Ford F150 Front Box Kit OKSUFD106F: Front 2.5" Remote Reservoir Coilover Shock, Compression Adjuster, to suit 6" Lift, Single OKSUFD105R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single

Upgrade your steering performance with the FOX 2.0 Adventure Series Dual Steering Stabilizer Kit. The monotube high pressure design provides excellent steering response and reduced wander to provide a controlled feel even on trucks with oversized off-road tires. The added steering control also aids in improving tire wear and front end component life. Kits include cylinders, brackets and mounting hardware. Monotube high pressure design for superior steering response Reduces wander for a controlled driving experience Improves tire wear and extends component life Includes all necessary cylinders and mounting hardware 100% bolt-on installation for easy setup Perfect for oversized off-road tires Specifications Type : Dual Stabilizer Features & Benefits HD center mounted axle bracket and tie rod brackets to fit a pair of FOX 2.0 Adventure Series stabilizers Helps control front end shimmy caused by oversized wheels/tires Extends life of front end steering components End-to-end stabilizer design 100% bolt-on design InstallationInstallation Install Guide 1 Estimated time: 1 hour Difficulty: Moderately Easy Install Tools Basic Hand Tools Important Notes Requires minimum of 2" front suspension lift. Requires a minimum of 1-1/2" of bump stop extension. This dual system will not work on vehicles with 2" of lift or less. ComponentsKit Components 984-50-303 (FOX98450303): Fox Adv Shock 23.13 x 16.01 x 2-EB1/EB1 ZONF8002: Dual Steering Stabiliser Bracket Kit

Specifications Adjustable: No Finish: Powdercoat Front Lift Height: 4" Front Lift Method: Coil Springs Lift Type: Lift Kit Material: Metal Rear Lift Height: 3" Rear Lift Method: Cast Blocks Requires Metal Cutting: No Requires Welding: No Features & Benefits Heavy duty fabricated steel replacement radius arms that correct caster alignment while maximizing ground clearance Forged pitman arm to correct steering angles Heavy duty fabricated track bar relocation bracket to re-center front axle Full length Diesel/ Gas specific coil springs for a smooth ride Outback Kitters 2.5" Remote Reservoir Compression Adjustable Shocks Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 4.5 in. Backspace 37 x 12.5 with 18 x 9 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 6 hours Difficulty: Moderate Install ToolsWrenches: Standard Important Notes 37x12.50 tires may require minor trimming. Factory wheels fit when paired with factory / original equipment tire size. Two-piece rear drive shaft? Add a carrier bearing drop kit to reduce post-lift driveline angles and avoid / eliminate driveshaft vibration. When adding the Dual Stabilizer option you will get the dual opposing steering stabilizer in addition to the single OE Replacement. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models Some trucks with a rear driveline vibration may have a recall from Ford regarding the rear axle. (Safety Recall 21S31) Due to the recall procedure, Zone recommends to have this performed prior to installing the lift. ComponentsKit Components ZONF1413: 4" (Diesel) Front Coil, Single ZONF1450: Zone Offroad 2020-2022 F250/F350 4.5" Rear Box Kit ZONF1601: Radius Arm, Single ZONF1614: Zone Offroad 2017-2022 Ford F250/F350 4-6in Radius Arm Front Box Kit OKSUFD205F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single OKSUFD203R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 3" Lift, Single

Take your RAM 1500 to new heights with this 6" lift kit from Zone Offroad. Kits include everything needed from high strength crossmembers and steering knuckles to strut spacers and differential relocation brackets to maintain driveline angles. Get the look, performance, and capability your truck deserves with clearance for up to 37" tires. Specifications Front Lift Height: 6" Rear Lift Height: 5" Material: Steel Front Lift Method: Knuckle & Strut Spacer Rear Lift Method: Coil Springs Features & Benefits Corrects suspension, steering, and drive-line geometry for great on-road handling and improved off-road performance. Heavy-duty differential skid slate improves off-road protection. High-strength, CNC machined, replacement steering knuckles improve strength while correcting steering angles. Top mount strut and pre-load spacers set ride height and maintain ride quality. 5" rear coil springs achieve leveled stance while maintain ride quality and load capacity. Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 5 in. Backspace 37 x 12.5 with 18 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Moderate Important Notes Factory 22" use ZOND97AOK Will NOT fit 2019-2021 RAM 1500 Classic models, Refer to the 2018 kit listings. Will NOT fit models equipped with the Thermal Axle option. Reference build code DSK-P. Vehicles equipped with the Off-Road Group option require special steps similar to Ram 1500 Rebel. To find out if your truck is equipped with the Off-Road Group, call your local Ram dealer, provide your VIN and ask if they can pull your window sticker. In the “Optional Equipment” section there will be a line item that reads “Off-Road Group” if your truck is equipped. RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ. Stock 17" wheels cannot be reinstalled due to steering interference. Stock 20s can be reinstalled with factory tire size. This kit will NOT work on Diesel models. Fitment: Does NOT work for models with factory rear airbag suspension. IF USING 18IN WHEELS WITH MAXIMUM RECOMMENDED BACKSPACING, TEST FIT WHEELS ON VEHICLE BEFORE MOUNTING TIRES TO ENSURE CLEARANCE ComponentsKit Components ZOND2630: Zone Offroad 2019-2023 RAM 1500 4wd Knuckle Box Kit Std - Drv ZOND2631: Zone Offroad 2019-2023 RAM 1500 4wd Knuckle Box Kit Std - Pass ZOND2639: Zone Offroad 2019-2023 RAM 1500 4wd 3-5" Rear Box Kit ZOND2642: Zone Offroad 2019-2023 RAM 1500 4wd 4-6" Front Box Kit 1 of 2 ZOND2643: Zone Offroad 2019-2023 RAM 1500 4wd 4-6" Front Box Kit 2 of 2 ZOND3509: Zone Offroad 2019-2023 RAM 1500 4wd 5" Rear Box Kit OKSURA106F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suit 6" Lift, Single OKSURA405R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 5" Lift, Single

Take your 2019+ RAM 1500 to new heights with the new 4 IFS Lift System from Zone Offroad. Specially designed for the new RAM trucks to improve stance with clearance for larger tires. These kits are built right here in the USA to the highest quality standards to all for improved on-road and offroad performance. As with all Zone Offroad lift kits, these new kits are backed by Factory Protection Plus for peace of mind wherever your adventures may take you. Factory Protection Plus includes Zone Offroads Limited Lifetime Warranty, ESC system compatibility and a 5-year 100,000-mile drivetrain warranty. Maintains on-road handling while improving offroad performance Heavy duty cross members and skid plates for protection New steering knuckles add strength and allow ESC system compatibility Top mounted front strut spacer retains factory ride quality Available with Nitro Series or FOX 2.0 Adventure Series rear shocks Allows fitment of up to 35 inch tires Specifications Front Lift Height: 4" Rear Lift Height: 3" Material: Steel Front Lift Method: Strut Spacers Rear Lift Method: Coil Springs Lift Type: Lift Kit Finish: Powdercoat Cutting Required: Yes Features & Benefits Maintains on-road handling while improving offroad performance Heady duty cross members and skid plates for protection New steering knuckles add strength and allow ESC system compatibility Top mounted front strut spacer retains factory ride quality Available with Nitro Series or FOX 2.0 Adventure Series rear shocks Allows fitment of up to 35" tires Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 5 in. Backspace 35 x 12.5 with 18 x 9 and 5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Moderate Easy Important Notes Will NOT fit 2019-2021 RAM 1500 Classic models, Refer to the 2018 kit listings. Will NOT fit models equipped with the Thermal Axle option (Reference build code DSK-P). Will NOT fit Ram 1500 Rebel or Ram 1500 with Off-Road Group option. Vehicles equipped with the Off-Road Group option require the Ram 1500 Rebel 4in kit to achieve correct ride height. To find out if your truck is equipped with the Off-Road Group, call your local Ram dealer, provide your VIN and ask if they can pull your window sticker. In the “Optional Equipment” section there will be a line item that reads “Off-Road Group” if your truck is equipped. RAMs with factory 22" wheels require the larger bore knuckles due to larger wheel bearing assembly. Reference build code WPM or WPZ. Stock 17" wheels cannot be reinstalled due to steering interference. Stock 20s can be reinstalled with factory tire size. This kit will NOT work on Diesel models. Fitment: Does NOT work for models with factory rear airbag suspension. IF USING 18IN WHEELS WITH MAXIMUM RECOMMENDED BACKSPACING, TEST FIT WHEELS ON VEHICLE BEFORE MOUNTING TIRES TO ENSURE CLEARANCE ComponentsKit Components ZOND2630: Zone Offroad 2019-2023 RAM 1500 4wd Knuckle Box Kit Std - Drv ZOND2631: Zone Offroad 2019-2023 RAM 1500 4wd Knuckle Box Kit Std - Pass ZOND2639: Zone Offroad 2019-2023 RAM 1500 4wd 3-5" Rear Box Kit ZOND2642: Zone Offroad 2019-2023 RAM 1500 4wd 4-6" Front Box Kit 1 of 2 ZOND2643: Zone Offroad 2019-2023 RAM 1500 4wd 4-6" Front Box Kit 2 of 2 ZOND3309: Zone Offroad 2019-2023 RAM 1500 4wd 3" Rear Box Kit OKSURA104F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, to suit 4" Lift, Single OKSURA403R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 3" Lift, Single

Heavy duty 1/4" steel, laser cut, internally gusseted radius arms improve strength, offer more ground clearance and correct caster High strength progressive rate front coil springs for a great ride on any terrain F/R HD track bar relocation brackets to correctly position both axles under the truck Forged drop pitman arm to corect steering angles HD transmission crossmember and t-case indexing ring to correct front driveline angles Outback Kitters 2.5" Remote Reservoir shocks to improved ride and offroad performance Allows clearance for up to 37" tires Heavy duty steel radius arms enhance strength and ground clearance Progressive rate coil springs ensure a smooth ride on any terrain Track bar relocation brackets position axles correctly Forged drop pitman arm corrects steering angles Transmission crossmember and indexing ring optimize driveline angles Remote reservoir shocks improve off-road performance Specifications Accommodates Factory Wheels: Yes Adjustable: No Finish: Powdercoat Front Lift Height: 4.5" Front Lift Method: Strut Spacers Lift Type: Lift Kit Material: Steel Rear Lift Height: 2.5" Rear Lift Method: Coil Springs Requires Metal Cutting: Yes Requires Welding: No Features & Benefits Heavy duty 1/4" steel, laser cut, internally gusseted radius arms improve strength, offer more ground clearance and correct caster High strength progressive rate front coil springs for a great ride on any terrain F/R HD track bar relocation brackets to correctly position both axles under the truck Forged drop pitman arm to corect steering angles HD transmission crossmember and t-case indexing ring to correct front driveline angles Outback Kitters 2.5" Remote Reservoir shocks to improved ride and offroad performance Allows clearance for up to 37" tires Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 4.5 in. Backspace 37 x 12.5 with 20 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Install Guide 3 Estimated time: 9 hours Difficulty: 4 out of 5 Install Tools Pitman Arm Puller Important Notes Will NOT fit air-ride equipped models Diesel models only Vehicles with a Manual Shift Transfer Case require a Manual T-Case Indexing Kit. Add ZOND5409 in kit configuration. Trucks equipped with a 2-piece rear driveshaft require carrier bearing shim kit D5406 (not included with kit) ComponentsKit Components ZOND1258: 2.5" Rear Spacer Box Kit ZOND1403: 4.5" Replacement Radius Arm Box Kit ZOND1413: Radius Arms, Single ZOND3401: 4.5" (Diesel), 5.5" (Petrol) Coils ZOND5612: T-Case Index - 6 Bolt - Diesel OKSURA205F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 5" Lift, Single OKSURA205R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 5" Lift, Single

Features & Benefits Heavy duty fabricated steel radius arms that correct caster alignment while maximizing ground clearance. Forged pitman arm to correct steering angles. Heavy duty fabricated track bar relocation bracket to recenter the front axle. Full length specific coil springs which are gas or diesel specific. Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 6 hours Difficulty: Difficult Install Tools30mm Socket; 46mm Socket; Hydraulic Floor Jack and Jack Stands; Pitman Arm Puller Important Notes Two-piece rear drive shaft? Add a carrier bearing drop kit to reduce post-lift driveline angles and avoid / eliminate driveshaft vibration. When adding the Dual Stabilizer option, you will get the dual opposing steering stabilizer in addition to the single OE Replacement. Due to taller factory ride height, Tremor models will not net full advertised lift height. Final ride height will be the same as standard models. Some trucks with a rear drive-line vibration may have a recall from Ford regarding the rear axle. (Safety Recall 21S31) Due to the recall procedure, Zone recommends having this performed prior to installing the lift. Does not fit vehicles with radius arm mounted ride height sensors. Fits SRW models only Recalibration of your vehicles Advanced Driver Assistance System (ADAS) cameras, radars, light detection and ranging (LiDAR), and other sensors may be necessary by your local dealership or ADAS service center. This will ensure proper functionality of the vehicle features such as lane keeping, lane departure, parking assistance, blind-spot detection, adaptive cruise control systems, and other functions as they did prior to installation. Please connect with your local dealership or ADAS service center. Similar to a wheel alignment, all charges and expenses that may occur from dealership calibrations and adjustments are the sole responsibility of the vehicle owner. 37x12.50 tires may require minor trimming. Factory wheels fit when paired with factory / original equipment tire size. ComponentsKit Components ZONF1316: 5" Rear Block Kit- 2 & 3 Leaf Main - 17.25" U-Bolt ZONF1413: 4" (Diesel) Front Coil, Single ZONF1432: Zone Offroad Drivers Side Radius Arm (LHS) ZONF1433: Zone Offroad Passengers Side Radius Arm (RHS) ZONF1614: Zone Offroad 2017-2022 Ford F250/F350 4-6in Radius Arm Front Box Kit OKSUFD205F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single OKSUFD204F: Front 2.5" Remote Reservoir Front Shock, Compression Adjuster, to suit 4" Lift, Single

Elevate your truck’s status with this 4" Suspension Lift Kit that will let you clear those 35" tires. This kit has everything you need to give you the ride you want and the look that’s going to turn heads. Fits 4WD 2013 - 2018 Dodge / Ram 1500 Trucks. Corrects suspension and steering geometry for improved handling Heavy-duty differential skid plate for off-road protection CNC machined steering knuckles enhance strength Multiple rear lift heights for desired stance Top-mount strut spacers maintain ride quality Easy installation for a quick upgrade Specifications Front Lift Height: 4" Rear Lift Height: 2" or 3" Front Lift Method: Strut Spacers Rear Lift Method: Coil Springs or Spacers Lift Type: Lift Kit Features & Benefits Corrects suspension, steering, and driveline geometry for great on-road handling and improved off-road performance. Heavy-duty differential skid slate improves offroad protection. High-strength, CNC machined, replacement steering knuckles improve strength while correcting steering angles. Multiple rear lift heights available to achieve desired stance (see important notes). Top-mount strut spacers set ride height, maintain ride quality, and are easy to install. Tyre & WheelTyre & Wheel 35 x 12.5 with 17 x 9 and 4.5 in. Backspace 35 x 12.5 with 18 x 9 and 5 in. Backspace 35 x 12.5 with 20 x 9 and 5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 9 hours Difficulty: Moderate Important Notes Fitment: Does NOT work with all wheel drive (AWD) models. Fitment: Will NOT fit adjustable air suspension (air-ride) equipped models. Fitment: Does not fit eco-diesel models. Front drive shaft WILL fail prematurely Stock 17" wheels CAN NOT be re-installed. Stock 20" can be re-installed with factory tire. ComponentsKit Components ZOND2620: Zone Offroad RAM 1500 DS Box Kit (1of 5) ZOND2621: Zone Offroad RAM 1500 DS Box Kit (2 of 5) ZOND2612: Zone Offroad RAM 1500 DS Box Kit (3 of 5) ZOND2411: Zone Offroad RAM 1500 DS Box Kit (4 of 5) ZOND2408: Zone Offroad RAM 1500 DS Rear Box Kit (5 of 5) OKSURA104F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, to suit 4" Lift, Single OKSURA103R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 3" Lift, Single BDS022309: 3" Rear Box Kit

Stand out with a brand new, quality, yet affordable 6" suspension lift that lets you clear big 37" tires. Built for everyday driving but sturdy enough for off-road abuse. Get the look and performance you want out of your 4WD 2013 - 2018 Dodge / Ram 1500 Truck. Quality 6 inch suspension lift for enhanced performance Clear big 37 inch tires with ease Built for everyday driving and off-road durability Improves suspension and steering geometry Heavy-duty differential skid plate for protection CNC machined steering knuckles for strength Specifications Accommodates Factory Wheels: See Notes Adjustable: No Finish: Powdercoat Front Lift Height: 6" Front Lift Method: Strut Spacers Lift Type: Lift Kit Rear Lift Height: 3" or 5" Rear Lift Method: Coil Springs Requires Metal Cutting: No Requires Welding: No Features & Benefits This kit includes a 5" rear lift spring for a "Tail High" stance a 3" rear lift spring version of this kit is also available if you'd prefer a level rear end Corrects suspension, steering, and driveline geometry for great on-road handling and improved off-road performance Heavy-duty differential skid slate improves offroad protection High-strength, CNC machined, replacement steering knuckles improve strength while correcting steering angles Top mount strut and preload spacers set ride height and maintain ride quality Tyre & WheelTyre & Wheel 37 x 12.5 with 17 x 9 and 4.5 in. Backspace 37 x 12.5 with 18 x 9 and 5 in. Backspace 37 x 12.5 with 20 x 9 and 5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 9 hours Difficulty: Moderate Important Notes Does NOT work with all wheel drive (AWD) models. This kit is not recommended for TRX models. CV shaft vibration will occur on TRX models unless the TRX struts are replaced with standard struts. Instead, consider our 4" lift system for about 5" of TRX lift. Will NOT fit adjustable air suspension (air-ride) equipped models. Fitment: Does not fit eco-diesel models. Front drive shaft WILL fail prematurely. These trucks are typically between 1" and 3" tail high from the factory. Please measure your trucks factory front-to-back ride height and order the rear lift height to achieve the desired stance. If closer to 1" tail high from the factory order the 5" rear coils for a more level stance. If closer to 3" tail high from the factory order the 3" rear coils for a more level stance. Stock 17" wheels CAN NOT be re-installed. Stock 20" can be re-installed with factory tire. ComponentsKit Components ZOND2608: Zone Offroad 6" Rear Box Kit ZOND2620: Zone Offroad RAM 1500 DS Box Kit (1of 5) ZOND2621: Zone Offroad RAM 1500 DS Box Kit (2 of 5) ZOND2612: Zone Offroad RAM 1500 DS Box Kit (3 of 5) ZOND2614: Zone Offroad 6" Box Kit (4 of 5) 984-50-759 (FOX98450759): Fox Adv Shock 30.05 x 18.46 x 2-EB1/EB1

Specifications Adjustable: No Front Lift Height: 3" Front Lift Method: Coil Springs Lift Type: Suspension Rear Lift Height: 1.25" Rear Lift Method: Coil Spacer Requires Metal Cutting: No Requires Welding: No Features & Benefits High strength progressive rate front coil springs for a great ride on any terrain. Front HD track bar relocation bracket to correctly reposition the front axle. Nitro series gas or FOX adventure series IFP gas shocks to improved ride and offroad performance. Allows clearance for up to 35" tires Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 5 in. Backspace 35 x 12.5 with 17 x 9 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Estimated time: 6 hours Difficulty: Moderately Hard Install Tools Pitman Arm Puller Cutoff Wheel Important Notes Does not fit Power Wagon Does not fit Gas Models. Does not fit 2500 Air Ride models If you experience front driveline vibration, a T-case indexing ring is available for 6-bolt and 8-bolt equipped models. Be sure to select the correct one for your application ComponentsKit Components ZOND1126: Zone Offroad 2019-2024 Ram 2500 1.25" Rear Spacer Box Kit ZOND1301: 3" Front Box Kit ZOND1413: Radius Arms, Single ZOND3302: 3" (Diesel) Coil, Single OK411201-R20: Rear, 2" Lifted Coils, +20% Set of 2 OK401006: Rear Shock Guards, Set of 2 OKBKRA209: Brake Line Mounting Bracket Kit for Remote Res Shocks OKSURA203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 3" Lift, Single OKSURA202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single BDS122414: Front Sway Bar Disconnect Kit including Sway Bar Links

Specifications Front Lift Method : Cross Member & Strut Spacer Front Lift Height : 4" Rear Lift Method : Block Rear Lift Height : 3" Shocks Included : Yes Lift Height : 4-5.5" Features & Benefits Maintains on-road handling while improving off-road performance. Heavy duty crossmembers and skid plates for protection. New steering knuckles add strength and allow ESC system compatibility. Top mounted front strut spacer retains factory ride quality. Adventure Series upper control arms for additional strength and durability. Works with OEM shocks Tyre & WheelTyre & Wheel 35 x 12.5 with 18 x 9 and 4.5 in. Backspace 35 x 12.5 with 22 x 9 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Difficult Install ToolsCut off Tool Important Notes All aftermarket wheels should be test fit prior to mounting the tire to ensure proper clearance to the brake caliper. Requires frame bracket modification. Fits Gas and Diesel Models. Will not fit Adaptive Ride Control (ARC) equipped models. This system has not been tested on models equipped with Super Cruise. Optional front skid plate will not work with2.7L Turbo or Diesel engine. ComponentsKit Components ZONC2412: Chevy ZR2/GMC AT4X 4" Front Box Kit ZONC2662: Zone Offroad 2019-2024 Chevy/GMC 1500 Front Box Kit ZONC2672: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 1 w/UCA (4" and 6" Compatible) ZONC2673: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 2 w/UCA (4" and 6" Compatible)

Up the ante in your 2019-2024 RAM 1500 4WD truck with style and performance by installing this 2-inch lift kit featuring FOX Performance Elite 2.5 coil-over shocks from Zone Offroad. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 33" tires. Up front the lift kit includes FOX 2.5 Performance Elite Series remote reservoir coil-over shocks and heavy duty tubular upper control arms for increased strength. In the rear this kit utilizes a complementary set of FOX 2.5 Performance Elite shocks for the smoothest ride. FOX Performance Elite FOX 2.5 Performance Elite shocks offer next level performance for on-road comfort and off-road comfort capability. Tuned and ready to install right out of the box these bolt-on 2.5-inch diameter shocks are built for abuse and packed with race-proven technology. They include a remote reservoir for additional fluid capacity to keep your shocks running cool so you can push the limits in the rough terrain. The DSC adjuster adds remarkable versatility and precise tuning with a simple twist of either two adjuster knobs offering 10 separate low-speed and 12 high-speed compression levels with a black anodized aluminum reservoir to increase cooling efficiency. HD Upper Control Arms (UCAs) Built for strength performance and increased travel these upper control arms are ready to bolt-in with most leveled/lifted trucks. They use 1.5" OD x .120-wall tubular construction with an indexed ball joint cup to correct the ball joint positioning allowing additional down travel and camber adjustment. At the frame mounting ends are durometer-specific rubber bushings for maintenance-free operation while at the other end a quality greaseable ball joints for smooth quiet operation and superior durability. Arms are finished in a durable black powder coat with a billet aluminum dust cap ready for installation right out of the box. FOX 2.5 Performance Elite coil-overs offer improved damper performance over stock DSC Adjuster allows easy high-speed and low-speed compression tuning for optimal performance in any terrain UCAs increase strength and allow for more suspension travel Specifications Front Lift Method : Coil-Over Rear Lift Method : Stock Shocks Included : Yes Front Lift Height : 2" Rear Lift Height : 0" Features & Benefits FOX 2.5 Performance Elite coil-overs offer improved damper performance over stock DSC Adjuster allows easy high-speed and low-speed compression tuning for optimal performance in any terrain Performance UCAs increase strength and allow for more suspension travel Tyre & WheelTyre & Wheel 33 x 12.5 with 20 x 9 and 4.5 in. Backspace 295 / 65 with 20 x 9 and 5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Easy Important Notes Fits 4WD models only Vehicles equipped with "Offroad or Rebel Package" will not achieve full 2" of lift, net ride height change will be around 1" above stock. Will not fit vehicle equipped with factory Air Ride. Will NOT fit 2019-2022 RAM 1500 Classic models, Refer to the 2018 kit listings. ComponentsKit Components ZOND2301: Upper Control Arms, Suits 2", 3" & 6" Lift, Set of 2 883-06-165 (FOX88306165): Front Fox Performance Elite Series 2.5" Coilover Remote Reservoir DSC Shocks, Suits 2" Lift, Set of 2 883-26-079 (FOX88326079): Fox 2019+ Ram 1500 DT Rear 2.5" Remote Reservoir Shocks, 0-2" Lift, DSC, Set of 2

Take your Chevy ZR2 / ATX4 to new heights with this 4" lift kit from Zone Offroad. This system raises ride height 4” over stock and will sit at the same height as a 6” system would on a standard truck. Kits include everything needed from high strength crossmembers and steering knuckles to strut spacers, upper control arms and differential brackets to maintain driveline angles. This system is designed to take full advantage of the factory Multimatic shock system by correctly positioning them with an upper strut spacer in front and a relocation bracket in the rear. Our unique knuckle design allows for a much tighter turning radius than our competition, as well as a wider selection of wheel fitment options. Get the look, performance, and capability your truck deserves with clearance for up to 35" tires. High strength crossmembers for improved control arm positioning Ductile iron steering knuckles for enhanced steering geometry Strut spacers maintain Multimatic shock functionality Includes upper control arms for offroad protection Rear lift blocks for leveling and improved stance Unique knuckle design for tighter turning radius Specifications Front Lift Height: 4" Rear Lift Height: 3" Front Lift Method: Strut Spacers Rear Lift Method: Cast Blocks Lift Type: Lift Kit Is Adjustable: No Cutting Required: Yes Welding Required: No Features & Benefits High strength crossmembers to correct lower control arm positioning. Ductile iron steering knuckles and new tie rod ends to correct steering geometry and maintain ESC system compatibility. Strut spacers and shock relocation brackets to maintain Multimatic shock functionality. Kits include adventure series upper control arms and differential skid plate for additional offroad protection. Rear lift blocks and u-bolts to lift and level the stance, sway bar correction, brake line and bump stop relocation brackets to correct operating angles. Tyre & WheelTyre & Wheel (Chevy) 35 x 12.5 with 20 x 9 and 5.5 in. Backspace (GMC) 33 x 12.5 with 20 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Moderate Important Notes Requires frame bracket modification Designed to fit ZR2 or AT4X trucks only equipped with MultiMatic shocks Factory 17" and 18" wheels cannot be reinstalled due to tie rod interference, stock 20" wheels can be reinstalled All aftermarket wheels should be test fit prior to mounting the tire to ensure clearance to brake caliper Some wheel profiles will not clear the brake caliper. This can be test fit before the vehicle is lifted while still in stock condition Front skid plate will not work with 2.7L Turbo Engines Will NOT fit models with a single leaf spring (mono-leaf) rear suspension. Will NOT fit 25+ Models. Refer to ZONC77. ComponentsKit Components ZONC2400: Zone Offroad 2022-2023 Chevy ZR2 / GMC AT4X 4" Suspension Lift Box Kit ZONC2662: Zone Offroad 2019-2024 Chevy/GMC 1500 Front Box Kit ZONC2672: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 1 w/UCA (4" and 6" Compatible) ZONC2673: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 2 w/UCA (4" and 6" Compatible)

Take your Silverado/Sierra 1500 to new heights with this 6" lift kit from Zone Offroad. Kits include everything needed from high strength crossmembers and steering knuckles to strut spacers, Adventure Series upper control arms and differential relocation brackets to maintain driveline angles. Get the look, performance, and capability your truck deserves with clearance for up to 35" tires. Enhance your truck's off-road capability with a 6 inch lift kit Includes high strength crossmembers for improved stability Features adjustable shocks for customized ride quality Ductile iron steering knuckles ensure precise steering geometry Top mounted strut spacers for easy installation and lift Differential skid plate offers added protection on rugged terrain Specifications Front Lift Height: 6" Rear Lift Height: 5" Front Lift Method: Knuckle & Drop Cross-Member Rear Lift Method: Cast Blocks Lift Type: Lift Kit Features & Benefits Outback Kitters 2.5" Remote Reservoir Compression Adjustable Shocks High strength crossmembers to correct lower control arm positioning Ductile iron steering knuckles and new tie rod ends to correct steering geometry and maintain ESC system compatibility Top mounted strut spacers to provide lift and install easily Differential skid plate for additional offroad protection Adventure Series upper control arms for improved strength and durability Rear lift blocks and u-bolts to lift and level the stance Sway bar, brake line and bump stop relocation brackets to correct operating angles Tyre & WheelTyre & Wheel See Notes with See Notes and See Notes in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Moderately Hard Important Notes All aftermarket wheels should be test fit prior to mounting the tire to ensure proper clearance to the brake caliper. Fits Gas and Diesel Models. Optional front skid plate will not work with 2.7L Turbo or Diesel Engines. Requires frame bracket modification. Will NOT work with Adaptive Ride Control (ARC) equipped models (Use ZONC70 or ZONC72). Will NOT work with Trail Boss or AT4 models. Will NOT work with 2019-2020 1500 Classic Models. Will NOT work with Silverado ZR2 or Sierra AT4X models (Use ZONC73). This system has not been tested on models equipped with Super Cruise. If equipped with a mono-leaf rear spring please use part #UBT4064 (Qty 4 required) ComponentsKit Components ZONC2662: Zone Offroad 2019-2024 Chevy/GMC 1500 Front Box Kit ZONC2672: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 1 w/UCA (4" and 6" Compatible) ZONC2673: Zone Offroad 2019-2024 Chevy/GMC 1500 Knuckle Box Kit 2 w/UCA (4" and 6" Compatible) ZONC2663: 2019-2023 Chevy/GMC 1500 6" Box Kit ZONC5653: Zone Offroad 2019-2023 Chevy/GM Front Skid Plate OKSUCH106F: Outback Kitters 2020+ GMC Chev 1500 Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, to suit 6" Lift, Single OKSUCH105R: Outback Kitters 2020+ GMC Chev 1500 Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single

Improves off-road performance and handling Enhances vehicle stance and appearance Durable construction for long-lasting use Easy installation for DIY enthusiasts Compatible with various terrain types Boosts ground clearance for better obstacle navigation Specifications Accommodates Factory Wheels: See Notes Adjustable: No Finish: Powdercoat Front Lift Height: 3" Front Lift Method: Torsion Key Lift Type: Lift Kit Material: Steel Rear Lift Height: 2" Rear Lift Method: Fabricated Blocks Requires Metal Cutting: No Requires Welding: No Features & Benefits High strength UCAs are boxed and fully welded. They are specially designed with an indexed ball joint cup to correct ball joint operating angle for more suspension travel. Cast construction indexed torsion bar keys to provide additional ride height while maximizing ground clearance. Front differential relocation brackets to correct CV axle operating angle. Sway bar relocation brackets to maintain clearance and proper operating angle.2" rear lift blocks and heavy duty u-bolts to level the stance. Nitro series gas or FOX 2.0 adventure series IFP gas shocks to improve performance. Maintains ride and handling characteristics with clearance for 35" tires. Allows for improve offroad performance with more droop travel. Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 5.75 in. Backspace 295 / 60 with 20 x 9 and 6.18 in. Backspace 285 / 65 with 20 x 9 and 6.18 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 6 hours Difficulty: Medium Install ToolsTorsion Bar Unloading Tool Important Notes Stock wheels with stock tires can be installed, however clearance are very tight to the upper control arms, we recommend using a 1/4" wheel spacer.  Proper torsion bar key unloading tool required, (Kent Moore #CH48809 or equivalent) Will work on gas or diesel models. Will work on standard and AT4 models. Not recommended for DRW applications (may require custom u-bolts) ComponentsKit Components ZONC1207: 2" Rear Blocks & U-Bolts without Overload ZONC2320: 3" Lift Front UCAs and Torsion Keys OKSUCH203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-3" Lift, Single OKSUCH202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-2" Lift, Single

Improves off-road capability and ground clearance Designed for enhanced stability and control Durable construction for long-lasting performance Easy installation with no modifications required Compatible with various terrain types Optimized for a smooth ride on and off the road Specifications Accommodates Factory Wheels: See Notes Adjustable: No Finish: Powdercoat Front Lift Height: 3" Front Lift Method: Torsion Key Lift Type: Lift Kit Material: Steel Rear Lift Height: 2" Rear Lift Method: Fabricated Blocks Requires Metal Cutting: No Requires Welding: No Features & Benefits High strength UCAs are boxed and fully welded. They are specially designed with an indexed ball joint cup to correct ball joint operating angle for more suspension travel. Cast construction indexed torsion bar keys to provide additional ride height while maximizing ground clearance. Front differential relocation brackets to correct CV axle operating angle. Sway bar relocation brackets to maintain clearance and proper operating angle.2" rear lift blocks and heavy duty u-bolts to level the stance. Nitro series gas or FOX 2.0 adventure series IFP gas shocks to improve performance. Maintains ride and handling characteristics with clearance for 35" tires. Allows for improve offroad performance with more droop travel. Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 5.75 in. Backspace 295 / 60 with 20 x 9 and 6.18 in. Backspace 285 / 65 with 20 x 9 and 6.18 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Moderate Install ToolsTorsion Bar Unloading Tool Important Notes Stock wheels with stock tires can be installed, however clearance are very tight to the upper control arms, we recommend using a 1/4" wheel spacer. Proper torsion bar key unloading tool required, (Kent Moore #CH48809 or equivalent). Will work on gas or diesel models. Will work on standard and AT4 models. DRW applications reqire the "With Factory Overload" Option to get the correct U-Bolts. ComponentsKit Components ZONC1207: 2" Rear Blocks & U-Bolts without Overload ZONC2320: 3" Lift Front UCAs and Torsion Keys 987-24-010 (FOX98724010): Front Fox Performance Series 2.5" Smooth Body IFP HTO Shock, Suits 1.5-2.5" Lift, Single 987-24-009 (FOX98724009): Fox 2.5" Smooth Body IFP HTO Rear Shock to suit 0-1" Lift, Performance Series, Single

Specifications Accommodates Factory Wheels: No Adjustable: No Finish: Powdercoat Front Lift Height: 3.5" Front Lift Method: Strut Spacers Lift Type: Lift Kit Material: Steel Rear Lift Method: Cast Blocks Requires Metal Cutting: No Requires Welding: No Features & Benefits High strength UCAs are cast, ductile iron and specially designed with an indexed ball joint cup to correct ball joint operating angle for more suspension travel. Utilizes a combination top-mount and preload strut spacers to correctly lift vehicle. Retain factory ride quality without over extending suspension/drivelines at full suspension droop. Maintains ride and handling characteristics with clearance for larger tires.2" rear lift blocks and heavy duty u-bolts to level the stance. Nitro series gas or FOX 2.0 adventure series gas shocks to improve performance. Optional Steering Stops included for larger wheel/tire combinations. Tyre & WheelTyre & Wheel (Chevy) 37 x 12.5 with 20 x 9 and 5.5 in. Backspace (GMC) 35 x 12.5 with and in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Medium Install ToolsCut off Tool; Strut Compressor Important Notes Works on Gas and Diesel Models. All aftermarket wheels should be test fit prior to mounting the tire to ensure proper clearance to the brake caliper. Do not exceed wheel backspacing of 5.5" as it will cause clearance issues with UCA. Minor cutting of the factory droop limiter required to allow for the increased travel of replacement Upper Control Arms. Some wheel profiles will not clear the brake caliper. These can be test fitted before the vehicle is lifted in a stock condition. Will NOT fit Denali and High Country models with Adaptive Ride Control (ARC). Will NOT fit Trail Boss/ AT4 models. This kit has not been test fitted on Silverado ZR2 or Sierra AT4X models at this time. Will NOT fit models with a single leaf spring (mono-leaf) rear suspension. 2022 Models: This system has not been tested on models equipped with Super Cruise. Will NOT fit models with a single leaf spring (monoleaf) rear suspension. ComponentsKit Components ZONC2353: 2019-2024 Chevrolet Silverado/GMC Sierra 1500 3.5" Adventure Series Box Kit OKSUCH103F: Outback Kitters 2020+ GMC Chev 1500 Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, to suit 3" Lift, Single OKSUCH103R: Outback Kitters 2020+ GMC Chev 1500 Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 3" Lift, Single

Enhances off-road capability and performance Improves vehicle stance and appearance Durable construction for long-lasting use Easy installation for DIY enthusiasts Compatible with various terrain types Boosts ground clearance for better obstacle navigation Specifications Front Lift Height: 5" Rear Lift Height: 4.5" Material: 1/4" Steel Front Lift Method: Knuckle & Drop Cross-Member Rear Lift Method: Block Kit Lift Type: Suspension Features & Benefits Maintains ride quality and handling characteristics Improves ground clearance while correcting suspension-steering-driveline geometry High strength 1/4" thick steel crossmembers and differential skid plates CNC machined ductile iron steering knuckles to maintain ESC System compatibility Zone Offroad branded front skidplate and torsion bar relocation brackets Allows clearance for up to 37" tires to be installed Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 5.5 in. Backspace 35 x 12.5 with 20 x 10 and 5.5 in. Backspace 35 x 12.5 with 17 x 9 and 4.625 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 8 hours Difficulty: Difficult Important Notes Compatible with gas and diesel models as well as standard and AT4 equipped models. Frame bracket modifications required for installation. Stock 17-18" wheels cannot be reinstalled, stock 20" wheels can be reinstalled. Two-piece rear drive shaft? Add a carrier bearing drop kit to reduce post-lift driveline angles and avoid / eliminate driveshaft vibration. In some cases vehicles used in 4WD on the highway regularly could potentially experience a minor front driveline vibration. If this occurs we recommend replacing the front driveshaft with a dual cardan style driveshaft. ComponentsKit Components ZONC2459: Zone Offroad 2020-2024 Chevrolet Silverado/GMC Sierra 2500/3500 HD 4.5" Rear Block Kit w/o Overload ZONC2500: Zone Offroad 2020-2024 Chevrolet Silverado/GMC Sierra 2500/3500 HD Knuckle Box Kit - Drv ZONC2501: Knuckle Box Kit (RHS) ZONC2502: Zone Offroad 2020-2024 Chevrolet Silverado/GMC Sierra 2500/3500 HD Front Box Kit 1of3 ZONC2503: Zone Offroad 2020-2024 Chevrolet Silverado/GMC Sierra 2500/3500 HD Front Box Kit 2of3 ZONC2504: Zone Offroad 2020-2024 Chevrolet Silverado/GMC Sierra 2500/3500 HD Front Box Kit 3of3 OKSUCH205F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single OKSUCH205R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single

Take your Chevy/GMC HD to new heights with this 3" adventure series lift kit from Zone Offroad. Kits include everything needed from high strength upper control arms and indexed torsion bar keys to differential relocation spacers and a rear lift block kit to complete the install. Get the look, performance, and capability your truck deserves with clearance for up to 35" tires. Adventure series upper control arms enhance strength and travel Improved ride quality surpasses standard leveling kits Includes front differential drop for optimal CV angles Rear block kit provides a level to slightly tail high stance Indexed torsion bar keys allow precise ride height adjustment Clearance for up to 35" tires for rugged performance Specifications Front Lift Height: 3" Rear Lift Height: 2" Material: Metal Front Lift Method: Torsion Key Rear Lift Method: Cast Blocks Lift Type: Lift Kit Features & Benefits Adventure series fully boxed HD upper control arms for improved strength and suspension travel Improved ride quality and suspension travel over standard "leveling kits" Front differential drop included to correct CV shaft angles Rear 2" rear block kit will net a level to slightly tail high stance Indexed torsion bar keys to set ride height Allows clearance for up to 35" tires Tyre & WheelTyre & Wheel 34 x 11.5 with 17 x 9 and 5.5 in. Backspace 35 x 12.5 with 18 x 9 and 6 in. Backspace 35 x 12.5 with 20 x 9 and 6 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 5 hours Difficulty: Moderate Install Tools Torsion Bar Unloading Tool Important Notes Minor trimming may be required, especially if a wheel backspace of less the specified is used. Is not compatible with stock 20" rims, tyre will hit the upper control arm, wheels with a greater offset is required. Confirmed fitment for 2011-2019 ComponentsKit Components ZONC1207: 2" Rear Blocks & U-Bolts without Overload ZONC2311: 3" Box Kit 883-26-084 (FOX88326084): Front Fox Performance Elite Series 2.5" Remote Reservoir DSC Shocks, Suits 1.5-2.5" Lift, Set of 2 883-26-085 (FOX88326085): Rear Fox Performance Elite Series, 2.5" Remote Reservoir Shocks, DSC, 0-1" Lift, Suits 0-3" Lift Kits, Set of 2

Specifications Front Lift Height: 3" Rear Lift Height: 2" Features & Benefits Adventure series fully boxed HD upper control arms for improved strength and suspension travelImproved ride quality and suspension travel over standard "leveling kits". Front differential drop included to correct CV shaft angles. Rear 2" rear block kit will net a level to slightly tail high stanceIndexed torsion bar keys to set ride height. Allows clearance for up to 35" tires Tyre & WheelTyre & Wheel 34 x 11.5 with 17 x 9 and 5.5 in. Backspace 35 x 12.5 with 18 x 9 and 6 in. Backspace 35 x 12.5 with 20 x 9 and 6 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4.5 hours Difficulty: Moderate Install ToolsTorsion Bar Unloading Tool Important Notes Available for models with and without top mounted rear overload springs - be sure to select correct kit below for your application. Minor trimming may be required, especially if a wheel backspace of less the specified is used. Is not compatible with stock 20" rims, tyre will hit the upper control arm, wheels with a greater offset is required. ComponentsKit Components ZONC1207: 2" Rear Blocks & U-Bolts without Overload ZONC2311: 3" Box Kit OKSUCH203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-3" Lift, Single OKSUCH202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-2" Lift, Single

Take your Chevy/GMC HD to new heights with this 3" adventure series lift kit from Outback Kitters. Kits include everything needed from high strength upper control arms and indexed torsion bar keys to differential relocation spacers and a rear lift block kit to complete the install. Get the look, performance, and capability your truck deserves with clearance for up to 35" tires. Take your Chevy/GMC HD to new heights with this 3" adventure series lift kit from Outback Kitters. Kits include everything needed from high strength upper control arms and indexed torsion bar keys to differential relocation spacers and a rear lift block kit to complete the install. Get the look, performance, and capability your truck deserves with clearance for up to 35" tires. Specifications Accommodates Factory Wheels: See Notes Adjustable: No Finish: Powdercoat Front Lift Height: 3" Front Lift Method: Torsion Key Lift Type: Lift Kit Rear Lift Height: 2" Rear Lift Method: Cast Blocks Requires Metal Cutting: No Requires Welding: No Features & Benefits Adventure series fully boxed HD upper control arms for improved strength and suspension travelImproved ride quality and suspension travel over standard "leveling kits". Front differential drop included to correct CV shaft angles. Rear 2" rear block kit will net a level to slightly tail high stanceIndexed torsion bar keys to set ride height. Allows clearance for up to 35" tires Tyre & WheelTyre & Wheel 34 x 11.5 with 17 x 9 and 5.5 in. Backspace 35 x 12.5 with 18 x 9 and 6 in. Backspace 35 x 12.5 with 20 x 9 and 6 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4.5 hours Difficulty: Moderate Install ToolsTorsion Bar Unloading Tool Important Notes Available for models with and without top mounted rear overload springs - be sure to select correct kit below for your application. Minor trimming may be required, especially if a wheel backspace of less the specified is used. Optional steering stabilizer (PN# 7103) only fits vehicles that came equipped with a steering stabilizer from the factory. Requires 1/4" wheel spacer to accommodate stock 20" rims. ComponentsKit Components ZONC1207: 2" Rear Blocks & U-Bolts without Overload BDS121250: Upper Control Arms, Set of 2 ZONC1204: 2" Levelling Torsion Keys OKSUCH203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-3" Lift, Single OKSUCH202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-2" Lift, Single

Specifications Front Lift Height: 2" Rear Lift Height: 0" Features & Benefits Nodular cast iron torsion bar keys featured indexed slot to lift/level stance Shock extensions to allow use of factory shocks while properly limiting droop travel Torsion bar bolt keepers ensure bolt correct engagement and positioning Levels stance and allows clearance for 35" tires Quick install with easy to follow instructions Tyre & WheelTyre & Wheel 35 x 12.5 with stock and Stock in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Easy Install ToolsTorsion Bar Unloading Tool Important Notes Will fit AT4 models. Will fit petrol and diesel equipped models ComponentsKit Components ZONC1231: 2" Leveling Kit 987-24-010 (FOX98724010): Front Fox Performance Series 2.5" Smooth Body IFP HTO Shock, Suits 1.5-2.5" Lift, Single 987-24-011 (FOX98724011): Rear Fox Performance Series 2.5" Smooth Body IFP HTO Shock, Suits 1.5-2.5" Lift, Single

Improves vehicle stance and appearance Enhances ride quality and comfort Durable construction for long-lasting performance Easy installation with no special tools required Compatible with various off-road applications Boosts off-road capability and stability Specifications Front Lift Height: 2" Rear Lift Height: 0" Features & Benefits Nodular cast iron torsion bar keys featured indexed slot to lift/level stance. Shock extensions to allow use of factory shocks while properly limiting droop travel. Torsion bar bolt keepers ensure bolt correct engagement and positioning. Levels stance and allows clearance for 35" tires. Quick install with easy to follow instructions. Includes Factory Protection Plus warranty Tyre & WheelTyre & Wheel 35 x 12.5 with stock and Stock in. Backspace InstallationInstallation Install Guide 1 Estimated time: 6 hours Difficulty: Easy Install ToolsTorsion Bar Unloading Tool Important Notes Will fit AT4 models. Will fit petrol and diesel equipped models ComponentsKit Components ZONC1231: 2" Leveling Kit OKSUCH203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-3" Lift, Single OKSUCH202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-2" Lift, Single

Enhances off-road performance and stability Durable construction for long-lasting use Easy installation for a hassle-free upgrade Improves ground clearance for better visibility Optimized for a smooth ride on rough terrain Compatible with various truck models Specifications Accommodates Factory Wheels: See Notes Adjustable: No Finish: Powdercoat Front Lift Height: 5" Front Lift Method: Torsion Bar Drop Lift Type: Lift Kit Material: Steel Rear Lift Height: 3" Rear Lift Method: Cast Blocks Requires Metal Cutting: Yes Requires Welding: No Features & Benefits Heavy-duty differential skid slate improves off-road protection. High-strength, 1/4" steel construction crossmembers corrects lower control arm geometry. High-strength, CNC machined, replacement steering knuckles improve strength while correcting steering angles. No differential trimming required. Rear lift block and longer U-bolts for easy installation and level stance. Tyre & WheelTyre & Wheel 35 x 12.5 with 17 x 9 and 4.75 in. Backspace 285 / 65 with 20 x 9 and 6 in. Backspace 35 x 12.5 with 20 x 9 and 6 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 7 hours Difficulty: Difficult Install ToolsTorsion Bar Unloading Tool Important Notes 2015-2018 Models Only: 20" wheels can not be reinstalled due to GM changing the wheel thickness. The ID of the 20" wheels are smaller on 2015-2018 models. Fitment: WILL fit RWD models, however the front differential related parts in kit will not be used. Frame bracket modifications required for installation. Mod's Required: Modifications required for installation. See installation instructions for more information. Optional steering stabilizer (PN# 7103) only fits vehicles that came equipped with a steering stabilizer from the factory. Two-piece rear drive shaft? Add a carrier bearing drop kit to reduce post-lift driveline angles and avoid / eliminate driveshaft vibration. Will fit RWD models. The front differential related parts will not be used. With a 20" Wheel, 5"-6" backspacing is recommended. In some cases vehicles used in 4WD on the highway regularly could potentially experience a minor front driveline vibration. If this occurs we recommend replacing the front driveshaft with a dual cardan style driveshaft. ComponentsKit Components ZONC2630: Zone Offroad 2011-2019 Chevy/GMC HD 5in Front Box Kit (1of5) ZONC2631: Zone Offroad 2011-2019 Chevy/GMC HD 5in Front Box Kit (2of5) ZONC2632: Zone Offroad 2011-2019 Chevy/GMC HD 5in Front Box Kit (3of5) ZONC2633: Zone Offroad 2011-2019 Chevy/GMC HD 5in Front Box Kit (4of5) ZONC2634: Zone Offroad 2011-2019 Chevy/GMC HD 5in Front Box Kit (5of5) ZONC2639: Zone Offroad 2011-2019 Chevy/GMC HD 3in Rear w/o Top Overload OKSUCH205F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single OKSUCH205R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 5" Lift, Single

Get the look you've always wanted with this 2" torsion key leveling kit that allows you to upgrade your tires up to 34". Designed for 2011 - 2019 Chevy or GMC 2500HD /3500HD trucks. Zone Lift Kits: Engineered for Value, Manufactured for Reliability. 100 percent bolt on design for effortless installation Resonance frequency tested castings ensure durability Levels your truck's stance for a commanding look Allows for larger tires up to 34 inches Engineered for value and reliability Enhance your driving experience with improved handling Specifications Front Lift Height: 2" Rear Lift Height: 0" Features & Benefits 100% bolt-on design for easy installation. Castings are resonance frequency tested to ensure they are defect-free and ready to withstand any abuse. Levels out the stance of your truck and allows clearance for larger tires to be installed. Tyre & WheelTyre & Wheel 34 x 11.5 with 17 x 9 and 6 in. Backspace 34 x 11.5 with 18 x 9 and 6 in. Backspace 295 / 60 with 20 x 9 and 6 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 6 hours Difficulty: Easy ComponentsKit Components ZONC1204: 2" Levelling Torsion Keys 679: BDS Suspension Chev 2500 Bolt Pack - Differential Drop OKSUCH203F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-3" Lift, Single OKSUCH202R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 0-2" Lift, Single

Elevate your Ram 1500 DT with the Outback Kitters 2" Lift Kit Experience improved stance and ride quality with our 2.5" Remote Reservoir Shocks and Front/Rear Coils. Perfect fit for 35" tyres. Improved stance and ride quality with 2 inch lift kit Custom valved for heavier American trucks Allows clearance for up to 35 inch tires Finned remote reservoir for optimum cooling Durable zinc-plated steel body Includes Outback Kitters decal for added protection Specifications Max Tire Size: 35 x 12.5 Front Lift Height: 2" Rear Lift Height: 2" Features & Benefits Front Coilover Strut and Rear 2" Lifted Coils Front and Rear Outback Kitters 2.5" Remote Reservoir Compression Adjustable Shocks Allows clearance for up to 35” tires 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection Tyre & WheelTyre & Wheel Max Tire Size: 35 x 12.5 InstallationInstallation Install Guide 1 Estimated time: 5 hours Difficulty: Medium Important Notes Does not fit Ram 1500 DT Air Ride models Does not fit Ram 1500 DS models Will fit 2019-2024 model Ram 1500 DT with Coil Suspension ComponentsKit Components OKSURA102F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2" Lift, Single OKSURA402R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OK411101-R20: Rear, 2" Lifted Coils, +20%, Set of 2

ComponentsKit Components OKSURA103F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2-3" Lift, Single OKSURA402R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OK411101-R60: 2-3" Lifted Rear Coils, +60%, Set of 2 ZOND2301: Upper Control Arms, Suits 2", 3" & 6" Lift, Set of 2

ComponentsKit Components OKSURA103F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2-3" Lift, Single OKSURA402R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OK411101-R40: Rear, 2" Lifted Coils, +40%, Set of 2 ZOND2301: Upper Control Arms, Suits 2", 3" & 6" Lift, Set of 2

When 2" just isn't enough, well, why not take the extra inch. Go bold and make your Ram 1500 DT stand out from the pack with this 3" Lift Kit featuring Outback Kitters 2.5" Remote Reservoir Shocks, Rear Coils and the BDS Control Arms. This is a perfect fit for 35" tyres. Enhances vehicle performance and style Allows clearance for larger tires Features adjustable remote reservoir shocks Includes durable upper control arms Perfect for off-road adventures Transforms your vehicle's appearance and capability Features & Benefits Front Coilover Strut and Rear 2" Lifted Coils Front and Rear Outback Kitters 2.5" Remote Reservoir Compression Adjustable Shocks BDS Upper Control Arms Allows clearance for up to 35” tires InstallationInstallation Estimated time: 5 hours Difficulty: Medium ComponentsKit Components OKSURA103F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2-3" Lift, Single OKSURA402R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OK411101-R20: Rear, 2" Lifted Coils, +20%, Set of 2 BDS122253: Upper Control Arms, Suits 2-3" Lift, Set of 2

When 2" just isn't enough, well, why not take the extra inch. Go bold and make your Ram 1500 DT stand out from the pack with this 3" Lift Kit featuring Outback Kitters 2.5" Remote Reservoir Shocks, Rear Coils and the Zone Offroad Upper Control Arms. This is a perfect fit for 35" tyres. Enhances vehicle height for a bold look Compatible with 35 inch tires for off-road capability Includes adjustable remote reservoir shocks Improves suspension performance and handling Easy installation for DIY enthusiasts Durable construction for long-lasting use Features & Benefits Front Coilover Strut and Rear 2" Lifted Coils Front and Rear Outback Kitters 2.5" Remote Reservoir Compression Adjustable Shocks Upper Control Arms Allows clearance for up to 35” tires InstallationInstallation Estimated time: 5 hours Difficulty: Medium Important Notes Does not fit Ram 1500 DT Air Ride models Does not fit Ram 1500 DS models Will fit 2019-2024 model Ram 1500 DT with Coil Suspension ComponentsKit Components OKSURA103F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2-3" Lift, Single OKSURA402R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OK411101-R20: Rear, 2" Lifted Coils, +20%, Set of 2 ZOND2301: Upper Control Arms, Suits 2", 3" & 6" Lift, Set of 2

Outback Kitters Remote Reservoir Shocks Our shocks have been refined to withstand the harsh Australian conditions. Engineered for extreme durability in tough conditions Custom valving tailored for heavy American trucks Finned remote reservoir ensures optimal cooling Long hose allows for flexible installation options Zinc-plated steel body for enhanced corrosion resistance Rubber boots provide extra protection against debris Features & Benefits 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection

Lift up your nose on your RAM 2500 with the Outback Kitters 2" Levelling Kit. Designed with top-quality suspension components, including Front and Rear Outback Kitters 2.5" Remote Reservoir Shocks with Compression Adjuster, this kit ensures proper alignment and saves you money without sacrificing quality. Premium suspension components for enhanced performance Custom valving tailored for heavy-duty trucks Finned remote reservoir for superior cooling Durable zinc-plated steel body for longevity Adjustable compression valves for personalized comfort Rubber boots for added protection against elements Features & Benefits 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection Compression adjustable valves ComponentsKit Components OKSURA302F: Front 2.5" Remote Reservoir, Compression Adjuster, Suits 2" Lift, Single OKSURA300R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits Stock Height, Single OK411201-F20: Front, 2" Lifted Coils, +20%, Set of 2 OKBKRA209: Brake Line Mounting Bracket Kit for Remote Res Shocks

Lift up your Ram 3500 and get that staunch look that you have been waiting for. This kit from Outback Kitters features all the key components to lift up your Ram 2500 so you can fit those 35" tyres underneath and get better ground clearance. Enhances ground clearance for better off-road capability Custom valving for heavy-duty performance Zinc-plated steel body for durability Finned remote reservoir for optimal cooling Allows fitment of larger 35 inch tires Includes protective rubber boots for longevity Specifications Max Tire Size: 35 x 12.5 Front Lift Height: 2" Rear Lift Height: 1" or 2" 1" = 2" Levelling Kit Features & Benefits 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection Allows clearance for up to 35” tires Tyre & WheelTyre & Wheel Max Tire Size: 35 x 12.5 InstallationInstallation Estimated time: 6 hours Difficulty: Medium Important Notes Does not fit 3500 Factory Air Ride models ComponentsKit Components OKSURA202F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, Suits 2" Lift, Single OKSURA302R: Rear 2.5" Remote Reservoir 2.5" Rear Shock, Compression Adjuster, Suits 2" Lift, Single OK411201-F20: Front, 2" Lifted Coils, +20%, Set of 2 BDS012215: BDS Suspension 2019+ Ram 3500 2" Rear Spacer Block & U-Bolts, w/o Overload OKBKRA209: Brake Line Mounting Bracket Kit for Remote Res Shocks

Outback Kitters 1" Lift and Levelling Kits Want to improve the handling of your 2013+ Ram 2500 under load but don't want to lift it up too high? The Outback Kitters 1" Lift Kit is the perfect balance of support and comfort. Whether you're wanting support in the front from a bullbar or need a bit of extra carrying capacity in the back with a van in tow, this is the kit for you! Improves handling and comfort under load Perfect balance of support and stability Custom valved for heavier American trucks Finned remote reservoir for optimal cooling Rubber boots for added protection Long remote reservoir hose for perfect placement Specifications Max Tire Size: 34 x 12.5 Front Lift Height: 1" Rear Lift Height: Stock Height or 1" 1" = 1" Lift Kit Stock Coils = 1" Levelling Kit Features & Benefits 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection InstallationInstallation Install Guide 1 Estimated time: 5 hours Difficulty: Medium Important Notes Does not fit Air Ride models ComponentsKit Components OKSURA200F: Front 2.5" Remote Reservoir Shock, Compression Adjuster, Suits Stock Height, Single OKSURA200R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, Suits Stock Height, Single OK411200-F20: Front, 1" Lifted Coils, +20%, Set of 2 OKBKRA209: Brake Line Mounting Bracket Kit for Remote Res Shocks OK401006: Rear Shock Guards, Set of 2

2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection Compression adjustable valves Improved stance and ride quality Custom valved for heavy trucks Finned reservoir for optimal cooling Durable zinc-plated steel body Adjustable compression valves for customization Rubber boots for added protection Specifications Max Tire Size: 35 x 12.5 Front Lift Height: 2" Rear Lift Height: 2" Features & Benefits 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection Compression adjustable valves InstallationInstallation Estimated time: 5 hours Difficulty: Medium Important Notes Does not fit Ram 1500 DS Air Ride models Does not fit 2019+ Ram 1500 DT models ComponentsKit Components OKSURA102F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, Suits 2" Lift, Single OKSURA102R: Rear 2.5" Remote Reservoir Shock, Compression Adjuster, to suit 2" Lift, Single OK411100-R20: 2" Lifted Rear Coils

Upgrade the rear suspension of your Ram 1500 DS with the Outback Kitters Rear 2.5" Remote Reservoir Shock, designed to suit vehicles running a 2" lift. Featuring a remote reservoir and compression adjuster, this shock provides improved suspension control and adjustable damping for enhanced performance on and off the road. Key Features 2.5" Remote Reservoir Shock Compression adjustable for suspension tuning Designed to suit vehicles with a 2" lift Single rear shock Remote reservoir design for improved suspension performance Designed specifically for compatible Ram 1500 DS models Vehicle Fitment Ram 1500 DS: 2013–2024 Product Details Brand: Outback Kitters Product Type: OK 2.5" Remote Reservoir Shock SKU: OKSURA102R Lift Height: 2" Position: Rear Quantity: Single Made to Order: This product is made to order. Please call 0483 939 770 to confirm availability and lead time before ordering.

Outback Kitters Remote Reservoir Shocks Our shocks have been refined to withstand the harsh Australian conditions. Refined for harsh conditions Custom valved for heavy trucks Finned reservoir for optimal cooling Long hose for perfect placement Rubber boots for added protection Zinc-plated steel body for durability Features & Benefits Front shocks come with Coil-over 2.5" Zinc-Plated Steel Body Outback Kitters decal for additional protection Custom valved for the heavier American Trucks Finned Remote Reservoir for optimum cooling Long Remote Reservoir hose for perfect placement Rotating hose heads on shock and reservoir Rubber Boots for additional protection

Simply level out your Ford F250 and F350 Super Duty truck to the next level with this performance spring 2-inch leveling kit from Outback Kitters. Designed to improve stance, performance, and capability, this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. Up front the lift kit includes dual rate Pro-Ride coil springs, track bar relocation bracket for steering correction, and alignment cams. This kit is rounded out with Outback Kitters 2.5" Remote Reservoir Shocks to further dial in the comfort and control of your F250/F350. Pro-Ride Coil Springs A pair of full-length Pro-Ride coil springs are supplied to provide the correct lift height and smooth, predictable ride across various terrains. These dual rate springs utilize a softer initial spring rate over the factory for improved on-road comfort, while also using a higher secondary spring rate to provide stability and performance in harsh terrains. Specifications Front Lift Method : Coil Spring Rear Lift Method : Stock Shocks Included : Yes Front Lift Height : 2" Rear Lift Height : 0" Tyre & WheelTyre & Wheel 35 x 12.5 with 17 x 9 and 4.5 in. Backspace 35 x 12.5 with 18 x 9 and 4.5 in. Backspace 35 x 12.5 with 20 x 9 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Estimated time: 4 hours Difficulty: Moderately Easy Install Tools 30mm Socket Important Notes 2017-2019 models net 1" of lift height; requires an additional 1" coil spring spacer to sit level. 2020-2024 models net 2". Kit designed for diesel models; Gas models will achieve approx. 1/2" more ride height ComponentsKit Components OKSUFD202F: Front 2.5" Remote Reservoir Front Shock, Compression Adjuster, to suit 2" Lift, Single OKSUFD202R: Rear 2.5" Remote Reservoir Rear Shock, Compression Adjuster, to suit 2" Lift, Single BDS013205: Front Box Kit (17-19 = 1" / 2020+ = 2") OK412200-F20: Front 2" Lifted Coils, 20%, Set of 2

Lift up your Chevy Silverado 1500 and get that staunch look that you have been waiting for. This kit from Outback Kitters features all the key components to lift up your Chevy Silverado 1500 so you can fit those 35" tyres underneath and get better ground clearance. Lift up your Chevy Silverado 1500 and get that staunch look that you have been waiting for. This kit from Outback Kitters features all the key components to lift up your Chevy Silverado 1500 so you can fit those 35" tyres underneath and get better ground clearance. Specifications Front Lift Height: 2" Rear Lift Height: 1" or 2" 1" = 2" Levelling Kit 2" = 2" Lift Kit 2" Heavy Duty = 40% Load Rated Coils for Tray/Canopy setups Allows clearance for up to 35” tires Tyre & WheelTyre & Wheel Max Tire Size: 35 x 12.5 ComponentsKit Components OKSUCH102F: Front 2.5" Remote Reservoir Coilover Strut, Compression Adjuster, to suit 2" Height, Single OKSUCH102R: Rear 2.5" Remote Reservoir, Compression Adjuster, to suit 2" Height, Single

The Ram 2500/3500's are the ultimate towing rig, but there is one weak point that can't be overlooked. When building a heavy touring rig, the factory front shock mounts tend to fail prematurely, so that is why we highly recommend the Outback Kitters Front Shock Brace Brackets. These are a simple Bolt-In Solution when you are installing your suspension and then get welded in afterwards. So if your workshop doesn't have anyone to weld, simply install these and then take it to a fabricator to finish the job and paint them black. Unlike other brands, you do not have to grind off the existing shock mounts, as the Outback Kitters Shock Brace Brackets enhance the support of the factory mounts. 6mm steel construction for maximum durability Raw finish for a rugged look Simple bolt-on installation with welding for added strength Compatible with all shock brands for versatility Enhances factory mounts without grinding Perfect for heavy-duty towing applications Features & Benefits 6mm Steel Construction Raw Finish Bolt on Installation and then weld to finish Suits 2014+ Ram 2500 / 3500 vehicles Works with all shock brands InstallationInstallation Install Guide 1 Estimated time: 0.5 hours

BDS introduces a high-performance suspension upgrade for the popular Toyota Hilux, designed to deliver exceptional ride quality, strength, and off-road capability. This system features heavy-duty BDS upper control arms paired with Fox Adventure Series 2.0" Shocks. Each setup is built to handle tough terrain while improving handling and control, both on and off the road. The rear of the vehicle benefits from a collaboration between BDS Engineering and Fox Ride Engineering, with rear shocks precisely tuned to work in harmony with the Hilux’s aggressive factory spring rate. This ensures a balanced, responsive ride and maximum performance under load or during spirited driving. Whether you're loading up, heading off-road, or simply want a more composed ride, BDS delivers the suspension solution the Hilux was meant to have. Adventure Series 2.0 Coil-Over Snap Ring IFP Shocks Our Adventure Series 2.0 Coil-Over Snap Ring IFP shocks are a true bolt-on solution, loaded with a long list of features that set them apart. A custom-molded spring seat allows you to reuse the factory front springs and mounting hardware while providing excellent on- and off-road performance at an affordable price point. Built on the same proven design as the FOX 2.0 Performance Series, these shocks utilize a precision impact-extruded steel body for increased strength, durability, and corrosion resistance in demanding conditions. Inside each shock is an internal nitrogen-charged gas reservoir, contained by an Internal Floating Piston (IFP) that separates the nitrogen from the shock oil. This design prevents cavitation and oil aeration commonly found in factory twin-tube shocks, allowing maximum performance from FOX’s factory-tuned, high-flow piston and precision valving. Three predetermined snap-ring preload settings allow for 1”, 2”, or 3” of adjustable front lift, making it easy to dial in the desired stance. Paired with FOX 2.0 Adventure Series rear shocks, this kit delivers a comfortable on-road ride with predictable, controlled off-road handling in even the toughest terrain. The result is a well-balanced suspension upgrade that improves ride quality, control, and confidence without sacrificing daily drivability. BDS Suspension offers a high-performance upgrade for Toyota Hilux Designed for exceptional ride quality and off-road capability Features heavy-duty upper control arms and Fox Adventure Series shocks Precisely tuned rear shocks ensure balanced and responsive ride Allows for adjustable front lift to customize stance Delivers improved handling and control on tough terrain Specifications Front Lift Method : Coil-Over Front Lift Height : 2-3" Rear Lift Method : Block Rear Lift Height : 1" Shocks Included : Yes Features & Benefits 2-3" of lift depending on the front coil over selected. BDS upper control arms increase strength and allow for more suspension travel. Your choice of Fox coil-over options for customizable performance Front and rear Fox shocks designed and tuned for the popular Hilux application. Rear shocks specifically valved for factory Hilux leaf springs Enhanced stability and control across all driving conditions Backed by BDS’s No Fine Print Warranty Factory protection plus drivetrain warranty included. Easy, bolt on installation. Tyre & WheelTyre & Wheel 285 / 70 with 16 x 8 and 4.5 in. Backspace 285 / 70 with 17 x 8 and 4.5 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Moderate Install Tools 35mm Axle Nut Socket Cut-off Tool Important Notes Re-uses OEM spring and upper mount. ComponentsKit Components BDS018301: Upper Control Arms, 1" Rear Block, Set of 2 983-51-003 (FOX98351003): Front Fox Adventure Series 2.0" Snap Ring Shock 984-50-056 (FOX98450056): Rear Fox Adventure Series 2.0" Shock

Take your 2022-2024 Toyota Tundra truck to the next level and improve the ride with this 0-3-inch lift kit featuring FOX 2.5 Performance Elite Coilovers from BDS Suspension. Designed to improve stance, performance, and capability, this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. Up front the lift kit includes FOX 2.5 Performance Elite Coilovers with DSC remote reservoirs, heavy duty tubular upper control arms for increased strength, BDS heavy duty diff. drop brackets as well as solid aluminum sway bar drop blocks. In the rear this kit utilizes 1- 3/4" BDS heavy duty coil springs and a set of FOX 2.5 Performance Elite shocks with DSC remote reservoirs for ultimate adjustability that lets you dial in for the smoothest ride possible. DSC Adjustment FOX 2.5 Performance Elite front coil-overs and rear shocks come equipped with DSC (dual speed compression) adjustment to tune the high-speed and low-speed compression damping allowing for added control on-road with the ability to easily dial in more aggressive damping offroad. Tuning is a simple twist of the two clearly defined knobs with immediate feedback to dial it in for any terrain. HD Upper Control Arms (UCAs) Built for strength, performance and increased travel, these upper control arms are ready to bolt-in with most leveled/lifted trucks. They use 1.5" OD x .120-wall tubular construction with an indexed ball joint cup to correct the ball joint positioning allowing additional down travel and camber adjustment. At the frame mounting ends are durometer-specific rubber bushings for maintenance-free operation while at the other end a quality greaseable ball joints for smooth, quiet operation and superior durability. Arms are finished in a durable black powder coat with a billet aluminum dust cap ready for installation right out of the box. Improved damper performance with FOX 2.5 Performance Elite series Increased strength and suspension travel with BDS performance UCAs Ultimate adjustability with FOX 2.5 Performance Elite rear shocks Factory Protection Plus drivetrain warranty included Easy installation with 100% bolt-on design Designed for enhanced ride quality and off-road capability Specifications Front Lift Method : Coil-Over Rear Lift Method : Springs Shocks Included : Yes Front Lift Height : 3" Rear Lift Height : 1" Features & Benefits FOX 2.5 Performance Elite series DSC coil-overs offer improved damper performance over stock BDS performance UCAs increase strength and allow for more suspension travel FOX 2.5 Performance Elite series DSC rear shocks included Factory Protection Plus drivetrain warranty included Easy, 100% Bolt on installation Tyre & WheelTyre & Wheel 305 / 55 with 20 x 9 and 5 in. Backspace 285 / 65 with 20 x 9 and 6.18 in. Backspace 35 x 12.5 with 18 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Estimated time: 5 hours Difficulty: Moderate Install Tools Basic Hand Tools Hydraulic Floor Jack and Jack Stands Important Notes TRD Sports will achieve the same amount of lift but will have a lower stance than other models in the front Will not work with Adaptive Variable Suspension (AVS) System equipped vehicles Will not work with Air Ride models Will not work with TRD Pro models For regular off-road use, it is recommended to upgrade Non TRD Off-Road trucks half axles (CVs) to Toyota TRD's (Driver Toyota Part# 434200C020, Passenger Toyota Part# 434100C020). Not including TRD Pro model. Alternatively, the 67-52420CV - ReadyLift High-Performance CV Axle Kit For 2022+ Toyota Tundra Ball joint cap must be removed for maintenance of ball joint. Remove cap to access grease zerk. Grease at regular maintenance intervals For replacement ball joints, order BDS088200. Ball joints are not directional. The ADAS system in some vehicles needs to be recalibrated by a certified shop. The vehicle may warn the driver of potential collision from lower bridges, overhead signs/wires, and signs in windy conditions. Most windshield repair shops (Safelite) and dealers are capable of doing this. Use the Panhard Rods (Part# KPR190) for the perfect alignment ComponentsKit Components BDS028311: 3" Front Box Kit BDS038156: 1-3/4" Rear Coil Springs BDS128254: Upper Control Arms, Set of 2 884-06-318 (FOX88406318): Front Fox Performance Elite Series 2.5" Remote Reservoir DSC Shocks, Suits 3" Lift, Set of 2 883-26-139 (FOX88326139): Rear Fox Performance Elite Series 2.5" Remote Reservoir DSC Shocks, Suits 0-1.5" Lift, Set of 2

Experience superior off-road performance with the BDS 6.5" Lift Kit featuring Fox 2.5" PE Coilover DSC Shocks for enhanced stability and control Enhances off-road capability and performance Improves vehicle stability and control Includes high-quality Fox 2.5 inch PE Coilover DSC Shocks Designed for easy installation and durability Provides a striking lift for a commanding presence Perfect for serious off-road enthusiasts Specifications Adjustable Damping: Yes Adjustable: Yes Lift Height: 6.5" Pvg Product Status: Active Features & Benefits FOX 2.5 Coilovers w/ Remote DSC Adjustment Heavy duty tubular UCAs to improve travel Fully Boxed and Gusseted LCAs Next Level Performance On and Offroad Compatible with existing 4.5" and 6.5" BDS Lifts Easy Installation (Only minor welding for gusset) InstallationInstallation Install Guide 1 Estimated time: 4 hours Difficulty: Easy Important Notes Stock wheels and stock tyres cannot be reinstalled due to tie rod end interference. ComponentsKit Components BDS021303: BDS Suspension 2020-2024 GM HD LCA Kit - Drv BDS021304: BDS Suspension 2020-2024 GM HD LCA Kit - Pass BDS121301: BDS Suspension 2020-2024 GM HD C/O Conversion UCA Kit BDS121663: BDS Suspension 2020-2024 GM HD C/O Conversion Kit - 6.5" 884-06-339 (FOX88406339): Fox Chevy/GMC 2500/3500 HD Front Coilover, 2.5 Series, R/R 6.5" Lift, DSC

Take your 2022-2024 Toyota Tundra truck to the next level and improve the ride with this 2.25 inch lift kit featuring FOX 3.0 Internal Bypass Factory Race Coilovers from BDS Suspension. Designed to improve stance, performance, and capability, this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. Up front the lift kit includes FOX 3.0 Internal Bypass Factory Race Coilovers with DSC remote reservoirs, heavy duty tubular upper control arms for increased strength, BDS heavy duty diff. drop brackets as well as solid aluminum sway bar drop blocks. In the rear this kit utilizes 1- 3/4" BDS heavy duty coil springs and a set of FOX 3.0 Factory Race shocks with DSC remote reservoirs for ultimate adjustability that lets you dial in for the smoothest ride possible. FOX Factory Race Series FOX Factory Race Series 3.0 Internal Bypass shocks for the Toyota Tundra deliver position-sensitive damping technology, Dual Speed Compression (DSC) adjustment, and high-speed ready performance in a bolt-on kit. Patented Internal Bypass technology allows for multiple zones of damping control. The result is a comfortable, confident ride with increased damping force through rough terrain. Internal bypass shocks produce more force progressively to control hard bottom-outs, prevent harsh top-outs, and provide an initial catch for landing. Shock fluid bypasses the main piston through a series of bleed holes in the ride zone. As the shock extends past the ride zone in rebound or compression, the bleed holes terminate, forcing fluid through the main piston. Finned external reservoirs and aluminum shock bodies keep shock fluid temperatures cool for better performance. Type III anodization prevents corrosion and wear of the 3-inch diameter bodies. The DSC adjuster allows you to dial in your Tundra for load, environment, and driving style. FOX Internal Bypass shocks deliver the support and confidence you need while driving high-speed through rugged terrain. Experience race-bred performance next time you leave the pavement. HD Upper Control Arms (UCA) Built for strength, performance and increased travel, these upper control arms are ready to bolt-in with most leveled/lifted trucks. They use 1.5" OD x .120-wall tubular construction with an indexed ball joint cup to correct the ball joint positioning allowing additional down travel and camber adjustment. At the frame mounting ends are durometer-specific rubber bushings for maintenance-free operation while at the other end a quality greaseable ball joints for smooth, quiet operation and superior durability. Arms are finished in a durable black powder coat with a billet aluminum dust cap ready for installation right out of the box. Improved ride quality and performance with FOX 3.0 shocks Enhanced stance and capability for your Tundra Includes heavy duty upper control arms for strength Adjustable coilovers for a smooth ride Durable construction with corrosion-resistant finish Easy installation with all necessary components included Specifications Front Lift Method : Coil-Over Rear Lift Method : Springs Shocks Included : Yes Front Lift Height : 2.5" Rear Lift Height : 0" Features & Benefits 3.0" impact extruded and CNC machined 6061-T6 Type III anodized aluminum body Patented, internal bypass design Application-specific springs 7/8" stainless steel shafts Vehicle-specific tuning maximizes performance Redundant sealing pack system: main seal, wiper seal, scraper seal Finned reservoir, with DSC adjuster High strength 1.5-inch tubular construction improves strength and durability over stock UCA Indexed ball joint cup allows for increased travel on leveled/lifted applications Factory style rubber bushings for long lasting, maintenance-free operation High quality greaseable ball joints and a protective cap to keep out debris Fully assembled and ready to install right out of the box Tyre & WheelTyre & Wheel 305 / 55 with 20 x 9 and 5 in. Backspace 285 / 65 with 20 x 9 and 6.18 in. Backspace 35 x 12.5 with 18 x 9 and 5.5 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Estimated time: 4 hours Difficulty: Moderate Important Notes TRD Sports will achieve the same amount of lift but will have a lower stance than other models in the front Will not work with Adaptive Variable Suspension (AVS) System equipped vehicles Will not work with Air Ride models Will not work with TRD Pro models For regular off-road use, it is recommended to upgrade Non TRD Off-Road trucks half axles (CVs) to Toyota TRD's (Driver Toyota Part# 434200C020, Passenger Toyota Part# 434100C020). Not including TRD Pro model Ball joint cap must be removed for maintenance of ball joint. Remove cap to access grease zerk. Grease at regular maintenance intervals For replacement ball joints, order BDS088200. Ball joints are not directional. The ADAS system in some vehicles needs to be recalibrated by a certified shop. The vehicle may warn the driver of potential collision from lower bridges, overhead signs/wires, and signs in windy conditions. Most windshield repair shops (Safelite) and dealers are capable of doing this. ComponentsKit Components BDS028311: 3" Front Box Kit BDS038156: 1-3/4" Rear Coil Springs BDS128254: Upper Control Arms, Set of 2 883-06-219 (FOX88306219): Front Fox Factory Race Series 3.0 Internal Bypass Remote Reservoir DSC Shocks, Suits 2-2.25" Lift, Set of 2 883-26-142 (FOX88326142): Rear Fox Factory Race Series 3.0" Internal Bypass Remote Reservoir DSC Shocks, Suits 1-2" Lift, Set of 2

Elevate your ride with the BDS 6.5" Lift Kit featuring Fox 2.5" PES DSC Coilover Shocks for superior performance and style Experience superior off-road performance with advanced coilover technology Enhance your vehicle's stance for a commanding presence on the road Durable construction ensures long-lasting reliability and strength Easy installation process for a hassle-free upgrade Optimized for improved handling and ride quality Perfect for enthusiasts seeking adventure and style Specifications Front Lift Method : Coil-Over Rear Lift Method : Block Shocks Included : Yes Front Lift Height : 6.5" Rear Lift Height : 5" Features & Benefits FOX 2.5 coilovers offer improved damper performance over stock DSC Adjuster allows easy high-speed and low-speed compression tuning for optimal performance in any terrain Performance UCAs increase strength and allow for more suspension travel High Clearance design w/ no torsion bar drop maximizes ground clearance Robust steering knuckles maintain ESC system compliance HD skid plate system improved off-road protection Multipoint differential relocation brackets to secure the front axle and improve CV angles Factory Protection Plus drivetrain warranty included Tyre & WheelTyre & Wheel 37 x 12.5 with 20 x 9 and 4.5" to 5.5" in. Backspace InstallationInstallation Install Guide 1 Estimated time: 10 hours Difficulty: Difficult Important Notes Without Overload Rear Springs Models with two-piece rear drive shafts will require a carrier bearing drop kit. (BDS121612) Requires frame bracket modification. Stock wheels and stock tyres cannot be reinstalled due to tie rod end interference. Disassembly/assembly of the factory torsion bar system requires the use of a special unloading tool. The GM specified tool # is CH48809. Compatible with diesel models ONLY. Works with standard or AT4 diesel models. Some minor trim will be required with certain wheel/tire combination. This is normal with most aftermarket tire/wheel fitment on Chevy/GM trucks. Trimming will normally include the bottom edge of the inner fender shrouds and/or lower corner of front bumper valance. As a rule of thumb, deeper backspacing and shorter/narrower tires will reduce/eliminate trimming required. Further trimming tips are included at the end of this instruction sheet. In some cases vehicles used in 4WD on the highway regularly could potentially experience a minor front driveline vibration. If this occurs we recommend replacing the front driveshaft with a dual Cardan style driveshaft. Coilover coil has a large amount of preload, a coil spring compressor must be used to remove the coil from the coilover. Failure to use a coil spring compressor may result in death or injury. Do not increase coilover preload. For DRW models, use the w/ overload rear lift option. Will NOT work with AT4X or ZR2 models, lower control arm profile is different ComponentsKit Components BDS021690: 5-6.5" Knuckle Box Kit (LHS) BDS021691: 5-6.5" Knuckle Box Kit (RHS) BDS021692: 5-6.5" Front Box Kit (1 of 2) BDS021693: 5-6.5" Front Box Kit (2 of 2) BDS121661: BDS Suspension 2020+ Chevy/GMC 2500/3500 HD 5"-6.5" Skid Plate Box Kit BDS011516: 6.5" Rear Box Kit without overloads BDS121301: BDS Suspension 2020-2024 GM HD C/O Conversion UCA Kit BDS021303: BDS Suspension 2020-2024 GM HD LCA Kit - Drv BDS021304: BDS Suspension 2020-2024 GM HD LCA Kit - Pass BDS121663: BDS Suspension 2020-2024 GM HD C/O Conversion Kit - 6.5" 884-06-339 (FOX88406339): Fox Chevy/GMC 2500/3500 HD Front Coilover, 2.5 Series, R/R 6.5" Lift, DSC 884-26-031 (FOX88426031): Rear Fox Performance Elite Series 2.5" Remote Reservoir DSC Shocks, Suits 5-6.5" Lift, Set of 2

Up the ante in your 2020-2024 Chevy Silverado and GMC Sierra 2500 HD 4WD truck and improve the ride with this 3-inch lift kit featuring FOX 2.5 Performance HTO IFP shocks from BDS Suspension. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. These kits feature proprietary FOX 2.5 shocks designed specifically to bolt-on performance for increase travel and the ability to soak up the roughest terrain along with smooth on-road comfort. Up front the lift kit includes FOX 2.5 Performance Series HTO shocks and heavy duty tubular upper control arms for increased strength. Along with the control arms a pair of indexed cast steel torsion bar keys are supplied upfront to lift the vehicle and a small differential relocation kit is supplied to correct CV axle operating angles without affecting ground clearance. To eliminate sway bar interference a pair of sway bar relocation brackets is used which maintains proper operating angle. In the rear a 2" block and u-bolt kit is used to create a level to slightly tail high stance when unloaded. Rounding out these kits are a pair of specially tuned FOX 2.5 Performance Series HTO shocks ready to soak up the terrain. FOX Performance FOX 2.5 Performance Series HTO shock is a bolt-on shock loaded with position-sensitive technology, vehicle-specific valving, and larger pistons to improve on and off-road performance. A type II anodized aluminum body efficiently dissipates heat and prevents corrosion. The 2.5-inch shock body features an internal floating piston (IFP) to separate the shock oil from the high-pressure nitrogen, optimizing damping. Hydraulic Top Out (HTO) technology offers usable position-sensitive rebound damping control on and off the pavement. HTO reduces harsh top-outs and increases comfort by forcing shock oil through a secondary shim stack to slow down shock shaft speed; HTO is particularly beneficial after installing heavier, aggressive tires and applications lifted higher than OEM specification. Bolt-on 2.5 Performance Series HTO shocks to increase damping capacity and ride in comfort with position-sensitive rebound control. HD Upper Control Arms Built for strength performance and increased travel these upper control arms are ready to bolt-in with most leveled/lift Up the ante in your 2020-2024 Chevy Silverado and GMC Sierra 2500 HD 4WD truck and improve the ride with this 3-inch lift kit featuring FOX 2.5 Performance HTO IFP shocks from BDS Suspension. Designed to improve stance performance and capability this kit includes everything necessary to set your truck up right with clearance for up to 35" tires. These kits feature proprietary FOX 2.5 shocks designed specifically to bolt-on performance for increase travel and the ability to soak up the roughest terrain along with smooth on-road comfort. Up front the lift kit includes FOX 2.5 Performance Series HTO shocks and heavy duty tubular upper control arms for increased strength. Along with the control arms a pair of indexed cast steel torsion bar keys are supplied upfront to lift the vehicle and a small differential relocation kit is supplied to correct CV axle operating angles without affecting ground clearance. To eliminate sway bar interference a pair of sway bar relocation brackets is used which maintains proper operating angle. In the rear a 2" block and u-bolt kit is used to create a level to slightly tail high stance when unloaded. Rounding out these kits are a pair of specially tuned FOX 2.5 Performance Series HTO shocks ready to soak up the terrain. FOX Performance FOX 2.5 Performance Series HTO shock is a bolt-on shock loaded with position-sensitive technology, vehicle-specific valving, and larger pistons to improve on and off-road performance. A type II anodized aluminum body efficiently dissipates heat and prevents corrosion. The 2.5-inch shock body features an internal floating piston (IFP) to separate the shock oil from the high-pressure nitrogen, optimizing damping. Hydraulic Top Out (HTO) technology offers usable position-sensitive rebound damping control on and off the pavement. HTO reduces harsh top-outs and increases comfort by forcing shock oil through a secondary shim stack to slow down shock shaft speed; HTO is particularly beneficial after installing heavier, aggressive tires and applications lifted higher than OEM specification. Bolt-on 2.5 Performance Series HTO shocks to increase damping capacity and ride in comfort with position-sensitive rebound control. HD Upper Control Arms Built for strength performance and increased travel these upper control arms are ready to bolt-in with most leveled/lifted trucks. They use 1.5" OD x .120-wall tubular construction with an indexed ball joint cup to correct the ball joint positioning allowing additional down travel and camber adjustment. At the frame mounting ends are durometer-specific rubber bushings for maintenance-free operation while at the other end a quality greaseable ball joints for smooth quiet operation and superior durability. Arms are finished in a durable black powder coat with a billet aluminum dust cap ready for installation right out of the box. Specifications Front Lift Height: 3" Front Lift Method: Torsion Key Rear Lift Height: 2" Rear Lift Method: Block Rear Lift Option: 3 Inch Block Kit Without Overload Features & Benefits FOX 2.5 Performance Series HTO shock is a bolt-on shock loaded with position-sensitive technology, vehicle-specific valving, and larger pistons to improve on and off-road performance. Performance UCAs increase strength and allow for more suspension travel High strength cast torsion bar keys use an indexed design to provide additional ride height. Sway bar relocation for proper clearance Differential relocation to improve CV operating angle. Rear block and u-bolt kit provides lift while maintaining spring function and load capacity Tyre & WheelTyre & Wheel 35 x 12.5 with 20 x 9 and 5.75 in. Backspace 295 / 60 with 20 x 9 and 5.75 in. Backspace 285 / 65 with 20 x 9 and 6.18 in. Backspace InstallationInstallation Install Guide 1 Estimated time: 7 hours Difficulty: Moderate Install Tools Grinder Sanding Disc Torsion Bar Unloading Tool Important Notes Stock wheels and stock tyres cannot be reinstalled due to tie rod end interference. Disassembly/assembly of the factory torsion bar system requires the use of a special unloading tool (See OK221001 under suggestions) Some minor trimming may be necessary to fit certain wheel/tire combination. This is normal with most aftermarket tire/wheel fitment on Chevy/GM trucks and typically consists of trimming the bottom edge of the inner fender shrouds and/or lower corner of front bumper valance. As a rule of thumb, deeper backspacing and shorter/ narrower tires will reduce/eliminate trimming required. Further trimming tips are included at the end of this instruction sheet. Will NOT work with AT4X or ZR2 models, lower control arm profile is different ComponentsKit Components BDS011218X: 2" Rear Block without overloads BDS011310: 3" Box Kit includes Upper Control Arms & Torsion Keys 987-24-010 (FOX98724010): Front Fox Performance Series 2.5" Smooth Body IFP HTO Shock, Suits 1.5-2.5" Lift, Single 987-24-011 (FOX98724011): Rear Fox Performance Series 2.5" Smooth Body IFP HTO Shock, Suits 1.5-2.5" Lift, Single

Upgrade your ride with BDS Suspension's 4" Lift Kit featuring Fox 2.5" PE DSC Coilover Shocks for enhanced performance and style. Enhances off-road capability Improves ride quality Durable construction for long-lasting use Easy installation process Stylish lift for a commanding presence Compatible with various accessories Specifications Front Lift Method : Cross-Member Rear Lift Method : Block Shocks Included : Yes Front Lift Height : 4" Rear Lift Height : 2" Tyre & WheelTyre & Wheel 33 x 12.5 with 20 x 9 and 6.25 in. Backspace 35 x 12.5 with 20 x 9 and 6.25 in. Backspace InstallationInstallation Install Guide 1 Install Guide 2 Estimated time: 8 hours Difficulty: Difficult Install Tools36mm Socket; Cut Off Wheel or Equiv.; Ball Joint Separation Tool; Reciprocating Saw; Welding Equipment Important Notes Requires frame bracket modification Will not fit MagneRide / ARC equipped models Factory 17" and 18" wheels cannot be reinstalled due to tie rod end interference, stock 20" wheels can be reinstalled. 17" Wheels with 4.5" backspacing should be test fit prior to mounting the tire to ensure proper clearance to the steering knuckle / tie rod. All aftermarket wheels should be test fit prior to mounting the tire to ensure proper clearance to the brake caliper. Some wheel profiles will not clear the brake caliper. These can be test fitted before the vehicle is lifted in a stock condition. Will NOT work with TrailBoss or AT4 models. 2.7L models use Diesel kit for proper skid plate fitment This kit has not been test fit on Silverado ZR2 or Sierra AT4X models. If equipped with a mono-leaf rear spring please use part #UBT4064.(Qty. 4 required) Due to the Australian Remanufacturing Process, you will need to arrange custom hand brake lines. This needs to be factored in when arranging installation of the product. ComponentsKit Components BDS011316: BDS Suspension 2019+ Chevy/GMC 1500 Rear Box Kit - 4" BDS021664: Knuckle Box (1 of 2) with Upper Control Arm (4" and 6" Compatible) BDS021665: BDS Suspension 2019+ Chevy/GMC 1500 Knuckle Box 2of2 w/UCA (4" and 6" Compatible BDS021682: Chevy/GMC 4" or 6" Front Box Kit (1 of 2) BDS021683: Chevy/GMC 4 or 6" Front Box Kit (2 of 2) BDS121633: Coilover Reservoir Mounting Bracket Kit 884-06-321 (FOX88406321): Fox 2019+ Chevy/GMC 1500 Front 2.5" Remote Reservoir Coilover Shocks, Performance Elite Series, DSC, 4" Lift, Set of 2 884-26-023 (FOX88426023): Fox 2019+ Chevy/GMC 1500 Rear 2.5" Remote Reservoir Performance Elite Shocks, DSC, 4-6" Lift, Set of 2