3500

Introducing the VSS System for the Dodge RAM 2500HD 3500HD Limited (2019-Present), the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  100W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 1.5 Hours  Installation Difficulty - EasyBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 100W Maximum Power Voltage (Vmp) 21V Open Circuit Voltage (Voc) 24.78V Maximum Power Current (Imp) 4.76A Short Circuit Current (Isc) 5.23A

Introducing the VSS System for the Dodge RAM 2500 & 3500 (2018-current) EXTREME, the World’s First Vehicle Specific Bonnet-Mounted Solar Panel System. Key Features:  170W of clean solar energy to keep your battery topped up when the engine isn't running. Rugged “Marine-Grade” construction to withstand extreme environmental conditions. Perfect for overlanding, camping, and the jobsite. Keep your drinks cold and equipment charged without killing your battery. Solar Made Simple: An optional solar controller makes for everything you need for a clean and simple install. 3-year warranty. Approximate Installation Time - 2.5 Hours  Installation Difficulty - ModerateBenefits– Keep your vehicles battery topped up at all times: Perfect for the overlander or camper who wants to power devices without worrying about draining their battery. Perfect on the jobsite for work lights and charging cordless tools. – Extend the life of your battery: The VSS System will give you longer overall battery life by tending it constantly during periods of sun exposure. – Emergency engine starting device: If you ever manage to completely drain your battery the VSS will start the vehicle up again in as little as 30 minutes depending on sun exposure. – Anti-glare device: Due to it’s light absorbing properties the solar panel creates a surface with very low reflectivity across the bonnet of the vehicle.DescriptionThe VSS System hard-mounts to the bonnet of your vehicle, and during daylight hours, provides a constant flow of clean solar energy to your primary or secondary vehicle batteries. This gives you the ability to run 12V accessories like fridges, phone/laptop chargers, lights, power inverters etc. without the need to start your engine and without the fear of draining your battery and leaving you stranded. The VSS system is completely plug-and-play if paired with our optional MPPT solar charge controller and can be installed in as little as 1.5 hours. We chose the most stable and durable multilayers semi-flexible solar panel construction available to ensure that these solar panels can withstand extreme environmental conditions, maintenance-free, for years. The Future of Vehicle Charging is Here!FAQsWill Engine Heat Affect the VSS System? This is the most commonly asked question about our VSS System. It is a fact that solar cells lose efficiency as they warm up, however the simple answer is NO, engine heat will not have an effect on how the VSS system operates. Why you ask? Well, the main benefit of the VSS system is that it provides power to your vehicle battery when the engine is NOT running (and therefore not not). When the engine is running (and hot) the vehicle’s alternator is doing the majority of the charging and not the solar panel. This means there is very little effect from the additional heat on the system when the system is used for its intended benefits. In order to help with the heat build-up, each VSS panel is prepped with closed cell neoprene on the back of the panel. This serves two purposes; it lifts the panel up off of the bonnet creating an air packet between the panel and the bonnet allowing for cooling, while also helping to protect the vehicle bonnet from any contact with the back of the panel. Will the VSS System work with my battery? The MPPT charge controller included in our complete kits are programmed to charge a wide variety of battery types. Our system will work with AGM, Lead-Acid and Gel Cell Type Batteries. *we do not recommend the use of Optima Batteries with the VSS system. Can it be removed? Once installed the VSS system is not designated to be removed from the vehicle. The solar panel can be removed only if absolutely necessary. i.e., the panel needs to be replaced.Features Power 170W Maximum Power Voltage (Vmp) 19.5V Open Circuit Voltage (Voc) 23V Maximum Power Current (Imp) 3.58A Short Circuit Current (Isc) 3.94A

This kit creates a full-size rack that sits above your RAM 1500/2500/3500 6' 4" truck bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1560mm), 2 Tracks that install on top of the side channel of the load bed, and 6 Pickup Truck Bed Universal Legs that fit into the Tracks. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Drilling may be required to mount the track to the bed of your truck. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR018T - Ram 1500/2500/3500 6' 4" (2009-Current) Slimline II Top-Mount Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS027 - Leg Spacer 6mm (Pair)3x LASS038 - Pickup Roll Top/Top Mount Leg / Medium (Pair)1x RRAC939 - Pickup Load Bed Bolt Kit / 30mm1x RRSTP08 - SLII Tray - 1575mm(W)X1560mm(L)1x TRBU004 - Pick-Up Load Bed Tracks / 1600mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 38.4808kg (84.84lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 270mm (11")   Shipping Weight: Weight: 39kg (86lbs)

This 1358mm/53.5" long, full-size Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Ram Crew Cab 2009+. Drilling is required for installation. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. The vehicle specific foot rails have openings for storing compatible gear under the rack such as Front Runner tables. These Foot Rails contain 1 openings to access Front Runner under rack mount tables (1 smaller prep or 1 larger camp size table). All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: Both traditional and panoramic sunroofs may be operated in 'vent mode' and fully retracted, provided that you do NOT mount a table underneath. If you do mount a table underneath, only traditional sunroofs may be fully opened because they retract underneath the roof. Traditional sunroofs may NOT be operated in 'vent mode' because the table will interfere. Models with traditional sunroofs include: Ram 1500 (2009-2018), Ram 1500 Classic (2019-Current), Ram 2500/3500 (2019-Current) Models with panoramic sunroofs include: Ram 1500 (2019-Current) Features KRDR010T - Ram 1500/2500/3500 Crew Cab (2009-Current) Slimline II Roof Rack Kit by Front Runner Consisting of: 1x FADR001 - Ram 1500 Crew Cab (2009-Current) Foot Rails1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L)   Material used: Black epoxy powder - coated T6 aluminium High strength steel   Approximate Installed Weight: 29.68kg (65.43lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17"); Length: 1730mm (68"); Height: 260mm (10")   Shipping Weight: Weight: 31kg (68lbs)

This 1358mm/53.5" long, full-size, Slimline II cargo roof rack kit contains the Slimline II Tray, Wind Deflector and 2 Foot Rails to mount the Slimline II Tray to your Ram Crew Cab. Drilling into the vehicle's roof is required. All Front Runner Rack Kits contain installation instructions, as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: Some side mount accessories are not suited for low profile foot rails such as Hi-Lift Jack Bracket and Recovery Device & Gear Holding Side Brackets. Note: Traditional sunroofs may be fully opened because they retract underneath the roof. They may NOT be opened in vent mode, otherwise the Low Profile rack will interfere. If you wish to open a traditional sunroof in vent mode you may install Ram 1500/2500/3500 Crew Cab (2009-Current) Slimline II Roof Rack Kit, provided that you do NOT mount a table underneath. Models with traditional sunroofs include: Ram 1500 (2009-2018), Ram 1500 Classic (2019-Current), Ram 2500/3500 (2019-Current) Panoramic sunroofs may NOT be opened in any mode because they retract over the roof. If you wish to open a panoramic sunroof in any mode you may install Ram 1500/2500/3500 Crew Cab (2009-Current) Slimline II Roof Rack Kit, provided that you do NOT mount a table underneath. Models with panoramic sunroofs include: Ram 1500 (2019-Current) Features KRDR011T - Ram 1500/2500/3500 Crew Cab (2009-Current) Slimline II Roof Rack Kit / Low Profile by Front Runner Consisting of: 1x FADR003 - Ram 1500 Crew Cab(2009-Curr)Foot Rails/ Low 1x RRSTJ07 - SLII Tray - 1425mm(W)X1358mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 29.7kg (65.48lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 445mm (18") Length: 1730mm (68") Height: 250mm (10") Shipping Weight: Weight: 28.4kg (62lbs)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500/2500/3500 when fitted with a ReTrax XR rails. This low profile solution includes 4 Pickup Roll Top Leg Mounts, 2 x 1575mm Load Bars that fit into the existing ReTrax XR rails, and fitting instructions. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop-down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from stainless steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components, and the installation guide needed to fit Load Bars on a vehicle. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR025 - Ram 1500/2500/3500 ReTrax XR (2003-Current) Double Load Bar Kit - by Front Runner Consisting of: 2x LASS028 - Pick-Up Roll Top Leg Mount 1x LBSK018 - Roof Load Bar Pair 1575mm(W) Material used: Black epoxy powder - coated T6 aluminium Approximate Installed Weight: 6.8kg (14.99lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 170mm (7") Length: 1690mm (67") Height: 160mm (6") Shipping Weight: Weight: 8kg (18lbs)

This kit creates a full-size rack that sits above your Ram 1500/2500/3500s (w/ReTrax XR rails) load bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1762mm) and 6 Pickup Truck Bed Universal Legs that fit into the existing ReTrax XR rails. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR019T - Ram 1500/2500/3500 ReTrax XR 5'7" (2009-Current) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS028 - Pick-Up Roll Top Leg Mount 1x RRSTP08 - SLII Tray - 1575mm(W)X1560mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 32.68kg (72.05lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1730mm (68") Height: 260mm (10") Shipping Weight: Weight: 34kg (75lb)

A set of Pickup Bed Load Bars used to transport gear over the bed of your Ram 1500/2500/3500 w/ReTrax XR rails. This low profile solution includes 3 x 1575mm Load Bars and 6 Pickup Roll Top Leg Mounts that fit into the existing ReTrax XR rails. The Load Bars are mounted via Pickup Roll Top Load Mounts that bolt directly into the existing ReTrax XR rails. Allows for gear to be mounted above the pickups load bed. The load bed retains its load-carrying ability, while the drop down door functions as usual. Uses the same strong, corrosion-free aluminum slats found in Front Runner Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. Made from steel and a durable, weather-resistant black powder coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR022 - Ram 1500/2500/3500 ReTrax XR (2009-Current) Triple Load Bar Kit - by Front Runner Consisting of: 3x LASS028 - Pick-Up Roll Top Leg Mount 1x LBSK019 - Roof Load Bar Set 1575mm(W) Material used: Black epoxy powder - coated T6 aluminium Approximate Installed Weight: 9kg (19.84lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot, Grab-On Foot, or Strap-On Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicle's rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 160mm (6") Length: 1690mm (67") Height: 150mm (6") Shipping Weight: Weight: 10kg (22lbs)

This kit creates a full-size rack that sits above your Ram 1500/2500/3500s (w/ReTrax XR rails) load bed. This Slimline II cargo carrying rack kit contains the Slimline II tray (1575mm x 1762mm) and 6 Pickup Truck Bed Universal Legs that fit into the existing ReTrax XR rails. All Front Runner Rack Kits contain installation instructions as well as all the components needed to mount the Slimline II Tray to your vehicle. All Front Runner Racks are backed by a Limited Lifetime Warranty* Note: If your Roll Top extrusion has a 6mm (0.24") to 7mm (0.28") slot opening, you may need Track Mount Stud Plate for installation. Features KRDR020T - Ram 1500/2500/3500 ReTrax XR 6'4" (2003-Current) Slimline II Load Bed Rack Kit - by Front Runner Consisting of: 3x LASS027 - Leg Spacer 6mm (Pair) 3x LASS028 - Pick-Up Roll Top Leg Mount 1x RRSTP09 - SLII Tray - 1575mm(W)X1762mm(L) Material used: Black epoxy powder - coated T6 aluminium High strength steel Approximate Installed Weight: 35.79kg (78.9lbs) The t-slots on the tops and bottoms of the rack tray slats and edge profiles accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Slimline II Roof Rack, add the height of the Slimline II Tray (50mm/2") to the height of the Foot or Grab-on Foot listed above. If your Slimline II Roof Rack kit uses Legs, add the height of the Slimline II Tray (50mm/2") to the height of the Legs to determine the height of the rack from your vehicle's rain gutters. If your Slimline II Roof Rack kit uses Foot Rails, add the height of the Slimline II Tray (50mm/2") to the height of the Foot Rails to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width: 440mm (17") Length: 1730mm (68") Height: 260mm (10") Shipping Weight: Weight: 37kg (81lbs)

Effortlessly convert your Slimline II Roof Rack to an expedition style rack with the new Expedition Perimeter Rail Kit. This kit includes all hardware and components needed to fit rails to each length of the 1358mm long x 1345mm wide Front Runner Slimline II Roof Rack. The modular bolt-on design allows you to remove rail components whenever needed, such as to mount a roof top tent. Convert your Front Runner Slimline II Roof Rack at any time to a classic looking safari style basket shaped roof rack. No drilling is required for installation, and the kit adds extra cargo support with an attractive, low-profile design. Mounting hardware is included, and the rails are powder-coated with the same durable, weather-resistant finish as the Slimline II Roof Rack. The Expedition Rails add 63mm / 2.5" to the height of the roof rack and are manufactured with corrosion-resistant, high-density aluminum components. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:1x KRXG003 - Expedition Rail Kit - Front or Back -1345mm(W)1x KRXS007 - Expedition Rail Kit - Sides - 752mm to 1358mmMaterial Used:Black epoxy powder - coated T6 aluminiumHigh strength steelProduct Dimensions:1358mm (53.5") L x 1345mm (53") W x 63mm (2.5") H Weight:4.38 kg (9.7 lbs)

Effortlessly convert your Slimline II Roof Rack to an expedition style rack with the new Expedition Perimeter Rail Kit. This kit includes all hardware and components needed to fit rails to each length of the 1358mm long x 1425mm wide Front Runner Slimline II Roof Rack. The modular bolt-on design allows you to remove rail components whenever needed, such as to mount a roof top tent. Convert your Front Runner Slimline II Roof Rack at any time to a classic looking safari style basket shaped roof rack. No drilling is required for installation, and the kit adds extra cargo support with an attractive, low-profile design. Mounting hardware is included, and the rails are powder-coated with the same durable, weather-resistant finish as the Slimline II Roof Rack. The Expedition Rails add 63mm / 2.5" to the height of the roof rack and are manufactured with corrosion-resistant, high-density aluminum components. Note: A maximum driving speed of 130km/80mi per hour should be adhered to, when equipped with a Front Runner Roof Rack or Load Bar kit. Consisting of:1x KRXJ003 - Expedition Rail Kit - Front or Back -1425mm(W)1x KRXS007 - Expedition Rail Kit - Sides - 752mm to 1358mm Material Used:Black epoxy powder - coated T6 aluminiumHigh strength steel Product Dimensions:1358mm (53.5") L x 1425mm (56.1") W x 63mm (2.5") H Weight:4.5 kg (9.9 lbs)