All 4WD Parts and Accessories

A set of Gutter Mounted Load Bars used to transport gear on the roof of your vehicle when theres no need for a full Front Runner Roof Rack. This low profile, smaller footprint solution includes 4 225mm Gutter Mount legs, 2 1425mm Load Bars, 1 10mm Roof Load Bar Wind Deflector and fitting instructions - all the components necessary to mount the Front Runner Load Bars to a vehicle with gutters. You may not have the need for a full roof rack and find that you can get by using a set of Front Runner load bars. Can be used to mount a Front Runner Roof Top Tent or other accessories where a low profile and smaller footprint is preferred. The Load Bars are mounted directly to the rain gutters using Gutter Mounted Legs. Uses the same strong, corrosion free aluminum slats found in Front Runner Slimline II Racks. The sliding nut t-slots allow for quick fitting and removal of accessories and equipment on both the top and bottom of the slats. The Load Bars and Gutter Mount Legs can be used in the future as components to build a complete Front Runner Roof Rack. Made from stainless steel and a durable, weather resistant black powder-coated aluminum. Includes all hardware, components and the installation guide needed to fit Load Bars on a vehicle. PLEASE NOTE: The NAS roll cage on some Land Rover Defenders may interfere with the positing of the gutter mount legs. If you have a NAS roll cage on your Defender, please contact us before you make your purchase. Features KRLD024 - Land Rover Defender (1983-2016) Load Bar Kit / Gutter Mount - by Front Runner Consisting of: 2 x LASS107 - No 7 Leg 225mm (Pair) - by Front Runner 1 x LBSK016 - Roof Load Bar Pair 1425mm(W) - by Front Runner 1 x WDLB001 - Load Bar Wind Deflector / 10mm - by Front Runner Material used: Black epoxy powder-coated T6 aluminium High strength steel Approximate Installed Weight: 8kg (18lbs) The t-slots on the tops and bottoms of the slats accommodate standard 8mm bolts. To determine the approximate height from your vehicles roof to the top of your Load Bar Kit, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot or Grab-On Foot Foot listed above. If your Load Bar kit uses Legs, add the height of the Load Bar (22mm/ 7/8") to the height of the Legs listed above to determine the height of the rack from your vehicles rain gutters. If your Load Bar kit uses Foot Rails, add the height of the Load Bar (22mm/ 7/8") to the height of the Foot Rails listed above to determine the height of the rack from the crown (highest point) of the vehicles roof. Shipping Dimensions: Width 130mm (5") Length 1540mm (61") Height 195mm (8") Shipping Weight: Weight 9.5kg (21.0lbs)

This ladder clamps onto the gutter and bolts to the vehicle body. The bottom rung mounts below the bumper using existing holes. The ladder conforms to the contours of the vehicle and is made with off-road tough black powder-coated high-strength steel for maximum durability and strength. Easy installation: The top part of the ladder clamps onto the gutter and bolts to the vehicle body (drilling required). The bottom step mounts below the bumper using existing holes. Features Consists of: 1 x Land Rover Defender 90 110 (1983-2016) Ladder Installation Hardware Fitting Instructions Materials used: Black Powder coated steel & aluminium Product Dimensions: 155mm (6.1") L x 230mm (9.1") W x 721mm (28.4") H Weight: 4.51kg (9.9lbs)

Front Runner sump guards are designed for specific vehicle makes and models to ensure that the correct parts of the vehicle are protected from damage. Made of 6mm aluminium. Natural aluminum finish to compliment the Land Rover Defender. Fits both Left Hand and Right Hand drive vehicles. The 8mm black powder coated steel brackets mount to the existing mounting points on the Land Rover Defender. No drilling or vehicle modification required. Features Consists of: 1 x Aluminum Guard Plate 1 x Pair of Brackets Installation Hardware Fitting Instructions Materials used: 6mm Aluminum plate Black powder coated 8mm mild steel Product Dimensions: 373.5mm (14.7") L x 750mm (29.5") W x 252mm (9.9") H (Including brackets) Weight: 18.5kg (40.8lbs) Special Notes: Fits the Land Rover Defender 90 & 110 series

Unlock your van’s storage potential with this highly versatile, rugged roof rack kit for Mercedes-Benz Sprinter vans. Long distance van-life mission, weekend trip or hauling equipment such as ladders and pipes, the low profile rack is designed to support large loads. It features an adjustable slat system to accommodate just about any type of roof-mounted equipment such as air conditioning units, skylights and air vents. The rack's expansive load-carrying area was designed to carry gear and mount Front Runner accessories in a huge range of configurations. Compatible with Mercedes-Benz Sprinter L2H1 144" MWB standard roof vans with a vehicle length of 5923mm / 233.2". Load-carrying area: 3176mm (125") L x 1528mm (60.2"). Twelve (12) Mounting Feet secure into van's existing factory mounting points. Included Slat Bracket can be inverted for a lower profile at 85mm (3.4") height, or left in standard configuration at 127mm (5"). Compatible with most Front Runner accessories. Slats can be configured to any spacing to accommodate roof AC, vents, or any other accessories. Fitment guide and all mounting hardware are included. No drilling or modification required. All Front Runner racks are backed by a limited lifetime warranty.* WARNING Cancer or Reproductive Harm www.P65Warnings.ca.gov Consisting of:6x FAVF004 - Mercedes Sprinter Van Rack Foot Set1x RRAC207 - Van Rack Joiner Kit2x RRAC208 - Van Rack Side Profile End Caps3x RRAC940 - Merc Bens Sprinter Slimpro Van Track T-Bolt Kit4x RRNS1425 - Narrow Slat / 1425mm (Pair)2x SPVT003 - Van Rack Side Profile / 1560mm1x WDST013 - Wind Deflector Van Rack 30mm LipMaterial Used:Black epoxy powder - coated T6 aluminiumHigh strength steelApproximate Installed Weight: 32.72kg (72.14lbs)Shipping Dimensions:Width: 440mm (17")Length: 1730mm (68")Height: 160mm (6")Shipping Weight:Weight: 38kg (84lbs)

Once these brackets are installed on a Front Runner Rack, no tools are needed to remove or install a roof top tent. Simply release the tabs on the 6 latches and lift the tent away in seconds. No more wrenching in tight spaces during the off-season or time-consuming weekday removal of a roof top tent. This strong and rattle-free mounting system is built off-road tough for use with Front Runner Racks. Compatible with the Roof Top Tent and other popular soft shell tent brands like TJM, ARB, Tepui, etc*. Compatible with hard shell tents such as Autohome/Maggionlina, and James Baroud*. Hard shell tent owners please read **IMPORTANT NOTE below. 6 low profile base brackets are bolted to a Front Runner Rack while 6 self-aligning bushes are secured to the tent base channels using the appropriate Tent Channel Set. Secures in place with 6 latches with safety catches. Can be locked using Rack Accessory Lock / Small combination cable lock. Certain tent sizes and designs will dictate the height needed to clear the edge of the Front Runner Rack. The brackets are small, unobtrusive and can be left on the roof rack when the tent is not mounted, leaving vast rack space available. No tent modification is required. Removed tents can be stored on the ground, raised slightly off the floor by the supplied steel bushes. Supplied with all required mounting hardware. Fitting instructions are included. James Baroud Quick Release Tent Channel Set / 6 Piece or Autohome Quick Release Tent Channel Set / 6 Piece may be required for other tent brands (sold separately). *Soft shell and hard shell tents may need additional Nut Plates, sold separately. **IMPORTANT NOTE: Hard shell tents need additional support. If you are using these brackets with hard shell tents, such as James Baroud or Autohome, and you are unable to position the tent to rest directly on the rack, or the edges of the rack side profiles, use Hard Shell Tent Support Channels. Depending on the tent manufacturer, your hard shell tent warranty may be voided if your tent becomes damaged and you did not provide proper lateral support for the hard shell tent. Note: Extra Mounting Brackets may be required for some tent and rack combinations which require extra support. Features Consists of: 6 x Quick Release Brackets Installation Hardware Fitting Instructions Materials used: Black powder coated steel 304 Stainless steel Product Dimensions: (Per assembled bracket) 131mm (5.2") L x 142mm (5.6") W x 60mm (2.4") H Weight: 9.9kg (21.8lbs)

The Front Runner Tracks have been designed to accommodate a stud plate which slides into the t-slotted track and enables the foot assembly to be secured with nyloc nuts before the roof rack bolts on to the foot. Made from t-slotted aluminum extrusion. Often used for trailers and canopies to mount a rack or load bars. Each track is supplied with fitted double sided tape and a section of pre-cut rubber, which is used to protect the vehicle roof from the track. Powder coated black. Comes in pairs. Features TRAC003 - Universal Track / 1800mm(L) - by Front Runner Consisting of: 1 x TRAC003 - Universal Track / 1800mm(L) - by Front Runner Material used: Black epoxy powder-coated T6 aluminium Approximate Installed Weight 3kg (8lbs)   Shipping Dimensions: Width 110mm (4") Length 1880mm (74") Height 110mm (4") Shipping Weight: Weight 4.0kg (8.9lbs)

The Front Runner Gullwing window replaces the rear window of a Land Rover Defender allowing easy access to the cargo bay via the side of the vehicle.While built for off-road durability and ease of use, the Front Runner Aluminum Gullwing Window looks smart and was designed to blend seamlessly with the exterior stylings of the vehicle. Fits in minutes, no modifications required. Sealed with the same durable, weather resistant powder coating as the Front Runner Slimline II Roof Rack. Includes 2 locking latches. The Land Rover Defender can be brought back to stock within minutes by removing and replacing with standard window. Note: The glass and aluminium panels for the Land Rover Defender are not interchangeable.   Consists of:1x Aluminium gullwing door assembly1x Outer frame1x Fastening kit2x Gas struts1x Right side inner bracket1x Left side inner bracket1x Top inner bracket1x Bottom inner bracketMaterials used:Black powder-coated 3mm aluminiumBlack powder-coated 2mm mild steel reinforcement plateBlack powder-coated high strength steelProduct Dimensions:Overall: L 1120mm (44.1") x W 50mm (2") x H 490mm (19.3")Door Panel: L 1044mm (41.1") x H 414mm (16.3")Weight:15.5kg (34.2lbs)

Direction Plus™ Ryco Pre-Filter Kit RC671DPK is designed, engineered & assembled in Australia to suit Ford Next Gen Everest & Ranger models, protecting its engine against costly injector failure. Diesel contains more impurities than petrol, necessitating optimal filtration. This is crucial, especially while towing, taking your vehicle off-road, or accessing fuel of uncertain quality in remote areas. While the OE filter works well for many contaminants, it has limitations against water and other particles. UPDATE: Version 2 bracket released November 2023 now compatible for Touring & Premium Pack options with Auxilliary 6 switch pack (overhead switches) This kit fits: Ford Next-Gen Ranger & Everest (BF2S 3.0L 6cyl) 2022- On Compatible with Dual Battery Systems Ford Next-Gen Ranger & Everest (YN2S 2.0L 4cyl) 2022- On Compatible with Dual Battery Systems VW Amarok Core & Life NF – (DXWA 3.0L 6cyl) 2023- On  Excludes Aventura, Panamericana & Style due to different battery tray VW Amarok Core & Life NF – (DXK 2.0L 4cyl) 2023-On Excludes Aventura, Panamericana & Style due to different battery tray PROTECT YOUR ENGINE It’s easy to think that fuel contamination is something that happens “in the bush” but this is simply not true! Did you know that 72% of all diesel fuel injection system failures are caused by water and fuel lubricity problems? Direction Plus™ Ryco Pre-Filter kits are designed for modern high pressure fuel systems with a lift pump in the tank, offering 10-micron filter media, effectively removes 99% water and 98% particles from diesel fuel, providing maximum efficiency, life and flow to your vehicle’s fuel system. This protects the main fuel filter and engine from contamination-related damage. By fitting the Wireless Sensor Kit, it is a true fit-and-forget install, where you can monitor your pre-filter kit remotely, no longer having to look under the bonnet where space is restricted to check the bowl for water. HOW IT WORKS Installing a Direction Plus™ Ryco Pre-filter kit between the fuel tank and the O.E.M fuel filter, effectively removes 99% water and 98% particles from diesel fuel providing maximum efficiency, life and flow to your vehicle’s fuel system. This also leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system. For the ultimate front line defence against water and particle contamination, investing in a Direction Plus™ Ryco Pre-Filter Kit will protect your investment 24 hours a day, 365 days a year. BENEFITS OF A RYCO PRE-FILTER KIT: Isolate water before it journeys through your fuel system causing damage. Protect your fuel system from corrosion of metal components that left unaddressed can cause expensive damage to your fuel system. Reduce micro-bacterial growth caused by water contamination, which can reduce engine durability and performance. Remove other contaminants down to 10 microns, meaning your OE filter does not have to work as hard. Water resistant silicone coated filter media provides maximum efficiency, life and flow Maximum working Pressure 87 PSI/6 bar/600 kPa Give you a visible or audible alert to water in your fuel system allowing you to take action to protect your engine (when used with S102XK and S101X accessories). Allow you to easily drain water from your fuel system multiple times to get to safety or a mechanical workshop. Tested in the Ryco lab to meet or exceed OE equivalents and to international ISO and SAE standards  Check fitment guide below to confirm suitability for your vehicle.

Direction Plus™ Ryco Pre-Filter Kit RC645DPK is designed, engineered & assembled in Australia to suit Isuzu D-Max, MU-X and Mazda BT-50 models, protecting its engine against costly injector failure. Diesel contains more impurities than petrol, necessitating optimal filtration. This is crucial, especially while towing, taking your vehicle off-road, or accessing fuel of uncertain quality in remote areas. While the OE filter works well for many contaminants, it has limitations against water and other particles. This kit fits: Isuzu D-Max 4JJ3-TCX (3.0L 4cyl) 2020 – On Isuzu MU-X 4JJ3-TCX (3.0L 4cyl) 2021 – On Mazda BT-50 4JJ3-TCX (3.0L 4cyl) 2020 – On PROTECT YOUR ENGINE It’s easy to think that fuel contamination is something that happens “in the bush” but this is simply not true! Did you know that 72% of all diesel fuel injection system failures are caused by water and fuel lubricity problems? Direction Plus™ Ryco Pre-Filter kits are designed for modern high pressure fuel systems with a lift pump in the tank, offering 10-micron filter media, effectively removes 99% water and 98% particles from diesel fuel, providing maximum efficiency, life and flow to your vehicle’s fuel system. This protects the main fuel filter and engine from contamination-related damage. By fitting the Wireless Sensor Kit, it is a true fit-and-forget install, where you can monitor your pre-filter kit remotely, no longer having to look under the bonnet where space is restricted to check the bowl for water. HOW IT WORKS Installing a Direction Plus™ Ryco Pre-filter kit between the fuel tank and the O.E.M fuel filter, effectively removes 99% water and 98% particles from diesel fuel providing maximum efficiency, life and flow to your vehicle’s fuel system. This also leaves the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system. For the ultimate front line defence against water and particle contamination, investing in a Direction Plus™ Ryco Pre-Filter Kit will protect your investment 24 hours a day, 365 days a year. BENEFITS OF A RYCO PRE-FILTER KIT: Isolate water before it journeys through your fuel system causing damage. Protect your fuel system from corrosion of metal components that left unaddressed can cause expensive damage to your fuel system. Reduce micro-bacterial growth caused by water contamination, which can reduce engine durability and performance. Remove other contaminants down to 10 microns, meaning your OE filter does not have to work as hard. Water resistant silicone coated filter media provides maximum efficiency, life and flow Maximum working Pressure 87 PSI/6 bar/600 kPa Give you a visible or audible alert to water in your fuel system allowing you to take action to protect your engine (when used with S102XK and S101X accessories). Allow you to easily drain water from your fuel system multiple times to get to safety or a mechanical workshop. Tested in the Ryco lab to meet or exceed OE equivalents and to international ISO and SAE standards  Check fitment guide below to confirm suitability for your vehicle.

The NEW 32mm 14 row TransChill Arctic Black Transmission cooler kit TCB652DPK fits Mitsubishi Triton MV 4N16 (2024 – On) models. It is designed specifically to reduce excessive transmission heat caused by towing, carrying loads and driving in sand, snow, off-road or hot conditions. The TransChill Arctic Black Transmission cooler is an effective & economical way to keep the transmission at its optimum operating temperature. High efficiency turbulators in each tube direct the fluid for superior heat transfer. The unique 32mm plate & fin design allows for extreme cooling whilst the compact design is perfect for our vehicle specific mounting. New & Improved model Designed and engineered in Australia 32mm, 14 row fin & plate design allows for extreme cooling Durable Black powder coat resists oxidisation 100% pressure tested at 150psi for quality assurance Internal tubulation for efficient heat transfer Up to 50% more efficient (*heat transfer rate – BTU/hr) Pre-drilled mounting plates for easy installation Inlet & Outlet size: M16 fittings WHY DO YOU NEED ONE? Due to the extreme heat generated in an automatic transmission, an auxiliary oil cooler is an economical and efficient way to help protect against costly transmission repairs. Automatic Transmission Fluid (ATF) cools, lubricates and cleans internal transmission components. When transmission components exceed 93°C (200°F) the performance of ATF is seriously compromised. Subsequently the life span of the ATF, seals and internal components of the transmission are significantly reduced. Higher internal temperatures also increase the wear rate of the friction and clutch plates. HOW IT WORKS The Direction-Plus™ Transmission Cooler Kit can reduce the temperature of the ATF by as much as 33°C and assist maintaining acceptable operating temperatures. A reduction of just 11°C that can double the life expectancy of the transmission, ATF and all internal components. AUTOMATIC TRANSCHILL CONTENTS: Vehicle specific laser cut 4mm 5005-H34 aluminum mounting brackets All mounting hardware included ATF Hose (Meets or exceeds SAE J1019 requirements) 1x Davies Craig Black 32mm 14 row oil cooler 3yr Warranty *Conditions apply

The NEW 32mm 14 row TransChill Transmission cooler kit TCB601DPK fits Isuzu D-Max and MU-X 4JJ1TCX (3.0L 4cyl) 2012 – 2020 models and is designed specifically to reduce excessive transmission heat caused by towing, carrying loads and driving in sand, snow, off-road or hot conditions. The 32mm TransChill Transmission cooler is an effective & economical way to keep the transmission at its optimum operating temperature. High efficiency turbulators in each tube direct the fluid for superior heat transfer. The unique 32mm plate & fin design allows for extreme cooling whilst the compact design is perfect for our vehicle specific mounting. New & Improved model Designed and engineered in Australia 32mm, 14 row fin & plate design allows for extreme cooling Durable Black powder coat resists oxidisation 100% pressure tested at 150psi for quality assurance Internal tubulation for efficient heat transfer Up to 50% more efficient (*heat transfer rate – BTU/hr) Pre-drilled mounting plates for easy installation Inlet & Outlet size: M16 fittings WHY DO YOU NEED ONE? Due to the extreme heat generated in an automatic transmission, an auxiliary oil cooler is an economical and efficient way to help protect against costly transmission repairs. Automatic Transmission Fluid (ATF) cools, lubricates and cleans internal transmission components. When transmission components exceed 93°C (200°F) the performance of ATF is seriously compromised. Subsequently the life span of the ATF, seals and internal components of the transmission are significantly reduced. Higher internal temperatures also increase the wear rate of the friction and clutch plates. HOW IT WORKS The Direction-Plus™ Transmission Cooler Kit can reduce the temperature of the ATF by as much as 33°C and assist maintaining acceptable operating temperatures. A reduction of just 11°C that can double the life expectancy of the transmission, ATF and all internal components. AUTOMATIC TRANSCHILL CONTENTS: Vehicle specific laser cut 4mm 5005-H34 aluminum mounting brackets All mounting hardware included ATF Hose (Meets or exceeds SAE J1019 requirements) 1x Davies Craig Black 32mm 14 row oil cooler 3yr Warranty *Conditions apply

POLYAIR 'ULTIMATE' BELLOWS # 89416ULT LOAD ASSIST COMPLETE 'DOUBLE' AIR BAG KIT suit FORD RANGER 'RAPTOR' SERIES 2 - STANDARD HEIGHT ONLY. NOTE: FOR 08/2022 Onward Models NEXT GEN. RAPTORS ONLY with O.E. FOX 'COIL-OVER' REAR SHOCKS FITTED ONLY. This Kit suits ALL O.E.M. STANDARD HEIGHT 'RAPTOR' MODELS ONLY, NOT SUITABLE FOR RAISED HEIGHT RAPTORS *** NOTE: NOT SUITABLE FOR LEAF SPRING REAR NEXT GEN RANGER UTES or 1ST GEN. RAPTOR MODELS ! This kit offers an EASY, NO DRILL, BOLT-IN FITMENT able to be fitted with ordinary hand tools, yourself. As the RANGER RAPTOR Model was primarily designed by Ford's Motorsport Dept. as an Off Road Action Vehicle, Polyair wanted to make sure that their Load Assist solution for this action vehicle retained the full downward articulation (Droop) of the Raptors unique suspension while still offering a premium Load Assist solution to maintain a level vehicle when Loaded for Work or for when Towing Duties were required. Polyair's BELLOWS ULTIMATE KIT includes their unique POLYAIR CRADLE Kit for Maximum Downward Suspension Travel when used as an off road vehicle. The Kit also uses their latest Polyair Ultimate Bellows which incorporates an INTERNAL BUMP STOP in each Air Bag Bellows for added protection and stopping power in rough terrain. This Kit offers the Ultimate Solution for this unique off road vehicle without reducing the wheel droop of the FOX Bypass Shocks and Coil-Over Suspension design. NO DRILLING OR MODIFICATIONS REQUIREDSUPER EASY TO INSTALLDOES NOT LIMIT THE EXSTING RAPTOR SUSPENSION'S 'FULL DROOP' PERFORMANCE - STILL ALLOWING MAXIMUM WHEEL DROOP / FULL EXTENSION.THIS KIT CAN CONBINED WITH ANY OF THE POLYAIR 'WIRELESS' COMPRESSOR SYSTEMS or BOSS ON-BOARD AIR SYSTEMS for even more convenience...2 YEAR WARRANTYFREE AUSTRALIA WIDE SHIPPING ON THIS AIR BAG KIT ONLY!

The Polyair Ultimate Series load assist airbag kits are specifically designed to suit coil sprung vehicles. The Ultimate Series unique design allows for a huge 60psi of pressure for those seriously heavy loads! When you load up the back of the vehicle or hook up a caravan or trailer, you’ll notice the rear end drop down; this drop can have some adverse effects on your vehicle’s safety and handling. Symptoms such as: - Suspension bottoming out - Rough ride - Excessive sway & body roll - Unpredictable braking characteristics - Poor headlight aim All this can be mitigated by simply installing a set of Polyair Ultimate Series! The airbag kit is air adjustable, giving you flexibility to tailor the level of support for your individual load types and weights. In this day and age, we are all expecting more out of our SUV’s and 4WD’s and as a result they are towing and carrying more and more. We at Polyair Springs have acknowledged this trend and have provided a solution with the ‘Polyair Ultimate Series’ The Ultimate Series significant 60psi pressure rating allows you to take on the tough loads, whether you are highway touring or travelling off the beaten track. The Polyair Ultimates are the most advanced polyurethane airbag on the market and will provide your vehicle with a new level of support! Features: - Air adjustable from 5-60psi ! - Tough molded polyurethane construction - Easy to install using common tools - Easy to follow, illustrated instructions - Quick connecting, easy to use air fittings. 2 year, unlimited km warranty Position: Rear Toyota - Landcruiser 300 Series

For over 60 years GME has designed and manufactured an extensive range of high quality accessories to suit a wide variety of applications. From 4WDing to Boating and Fishing, GME has a genuine accessory to meet every need. The BP017 is a 2000mAh IP67 Li-Ion Battery Pack that suits the TX6500S. Lithium-Ion Polymer Battery PackCapacity: 2000mAh7.2V DC1 Year Warranty Key FeaturesLithium-Ion Polymer Battery PackCapacity: 2000mAh7.2V DC In the boxBattery Pack

MSA 4X4 POWER FOLD BLACK TOWING MIRRORS FOR MITSUBISHI TRITON-TM1152 MSA 4X4’s patented, SEMA award-winning Towing Mirrors feature a large single mirror that pivots on a heavy-duty extension slide. Allowing the mirror to extend out when towing and return to a normal driving position, when not towing. Government guidelines state that the driver is required to see 20m past the widest point of the towed vehicle. MSA 4X4 has created a range of Towing Mirrors that meet this guideline and are specifically designed for Australian towing vehicles. The mirror is the subject of Chinese utility model No. 201721652844.X and international patent application No. PCT/AU2017/051320, as well as corresponding patents and patent applications in Australia, Belgium, Canada, China, France, Germany, the Netherlands, New Zealand, South Africa, Spain, the United Kingdom and the United States of America. The mirror is also the subject of international patent application No. PCT/AU2020/050810, as well as corresponding patents and patent applications in Australia, Canada, China, Europe, New Zealand, South Africa and the United States of America. The shape of the mirror is protected by Australian design registration No. 201715134 and Chinese design registration No. 201830077185.5. FEATURES:  Four different mirror positions Large, single mirror lens Adjustable viewing angles Vertical and horizontal adjustment Unique pivot design Fold inwards or outwards ADR Compliant Injection moulded and die-cast aluminium components INCLUDES:  MSA 4X4’s 5 Year Warranty NOTE: AM Radio reception may not be available Please note that mirrors may take up to 2 weeks to ship. We're working hard to get your order to you as quickly as possible. Thank you for your understanding and patience!

Suits Toyota Landcruiser 200 Series GXL/VX/Sahara Designed from the ground up, the way a quality 4WD storage system should be. Sick of shoving everything loosely in the back of a vehicle? Why not get organised with an MSA 4X4 Storage Drawer System. MSA 4X4’s Storage Drawer Systems are designed with a patented slide technology Now fitted with fully sealed, stainless steel bearings with Nylon rollers as standard. Offering a quieter, smoother operation under heavy loads and saving up to 3kg per Drawer Module. The entire drawer extends further from the frame, allowing 100% access to the drawers. No more hard-to-reach items at the back! MSA 4X4’s Storage Drawer Systems are constructed from aluminium and have anodised aluminium components. Super-strong, lightweight and comes with stainless steel fasteners used throughout for a rust-free, corrosion resistance lifetime of use. The patented “Stay-Open Block” allows the drawer to remain in an open position even on a 30-degree slope. They also feature an LED Light Strip that activates at full extension and has a manual override switch. A 100% safe and secure lock system that can not be levered open from underneath, is an exceptional security measure. Dust resistant seals around front panels ensure all the items stored inside stay clean and dust free. Flush-fitting wing kits are available for most 4WDs and utes, creating additional storage space between the Storage Drawer System and the inner sides of the car. Access to the space is gained through removing the wing and face panels. The reinforced wing kit brackets provide a fully supported base for fridge slides to be mounted onto the wing panels, allowing for more placement options. The impact force of an unsecured item, within a vehicle during an accident, can be twenty to thirty times its static weight. Therefore greatly increasing the potential of occupant injuries. MSA 4X4’s Storage Drawer Systems, and the attachments that come with them (cargo barrier mount points and child restraint points), have been crash-tested and are fully ADR compliant. Tested to ADR3/02, ADR34/01 and ADR42 and passed all the requirements prescribed by the ADRs and AS/NZS, without any structural weaknesses or degradation of the system. FEATURES:  100% Drawer extension for complete access Patented “Stay-Open Block” Rust resistant sealed bearings with Nylon rollers Internal LED Light Strip Safe and secure lock system Dust resistant seal Stainless steel fasteners Removable wing and face panels INCLUDES: Complete wing kits Cargo Barrier mounting points Child restraint points MSA 4X4’s Lifetime Guarantee PARTS INCLUDED: Right Drawer Module Right Fit Kit (includes floor extension) Right Wing Kit Single Width Trim EXTERNAL DIMENSIONS  +10mm for rear anchor bolts Overall drawer length = 1045mm (including handle lock) Overall drawer height = 275mm Overall single drawer width = 530mm (no wings) INTERNAL DIMENSIONS Usable drawer height = 215mm (upto under side of the top deck) Drawer height = 211mm Internal drawer length = 930mm Internal drawer width = 453mm  

MSA 4x4 Ford Ranger PY Double Storage Drawer System- 41013 SUITS: Ford Ranger PY Ford Ranger PY FEATURES:  100% Drawer extension for complete access Patented “Stay-Open Block” Rust resistant sealed bearings with Nylon rollers Internal LED Light Strip Safe and secure lock system Dust resistant seal Stainless steel fasteners Removable wing and face panels INCLUDES: Complete wing kits Cargo Barrier mounting points Child restraint points MSA 4X4’s Lifetime Guarantee PARTS INCLUDED: Left Drawer Module Left Fit Kit(includes floor extension) Left Wing Kit Right Drawer Module Right Fit Kit (includes floor extension) Right Wing Kit Double Drawer Joining Bolts Double Width Trim Double Drawer Joining Wire EXTERNAL DIMENSIONS +10mm for rear anchor bolts Overall drawer length = 1365mm (including handle lock) Overall drawer height = 275mm Overall single drawer width = 530mm (no wings) INTERNAL DIMENSIONS Usable drawer height = 215mm (upto under side of the top deck) Drawer height = 211mm Internal drawer length = 1250mm Internal drawer width = 453mm  

VEHICLE DATE: 2015-02/2024 PRODUCT TYPE: Power Fold SUITS: Mitsubishi Triton Chrome, Electric, Heated, Indicators, Blind Spot Monitoring, Power Fold FEATURES:  Four different mirror positions Large, single mirror lens Adjustable viewing angles Vertical and horizontal adjustment Unique pivot design Fold inwards or outwards ADR Compliant Injection moulded and die-cast aluminium components INCLUDES:  MSA 4X4’s 5 Year Warranty MSA POWER FOLD™ is a trademark used under licence

VEHICLE DATE: 2018-Current PRODUCT TYPE: NON Power Fold SUITS: Ram 1500 Black, Electric, Heated, Temp Sensor FEATURES:  Four different mirror positions Large, single mirror lens Adjustable viewing angles Vertical and horizontal adjustment Unique pivot design Fold inwards or outwards ADR Compliant Injection moulded and die-cast aluminium components INCLUDES:  MSA 4X4’s 5 Year Warranty

MSA 4X4 SL95 Straight Slide FEATURES: Compact size Easy install Lock-in and lock-out safety system Powder-coated steel frame construction Stainless steel and blue anodised aluminium fittings Travel lock and key Anodised blue faceplate INCLUDES: All fixing and tie-down straps MSA 4X4’s Lifetime Guarantee NOTE: MSA 4X4 Fridge Barrier is available for this model